Professional Documents
Culture Documents
RCD-M41 Rcd-M41Dab: Click Here!
RCD-M41 Rcd-M41Dab: Click Here!
RCD-M41 Rcd-M41Dab: Click Here!
11
CD RECEIVER
Click here!
RCD-M41 Online service parts list
RCD-M41DAB https://dmedia.soundunited.com/documents/details/23162
Online Parts List (P5 to P7)
CAUTION IN SERVICING
ELECTRICAL
MECHANICAL
REPAIR INFORMATION
UPDATING
• For purposes of improvement, specifications and design are subject to change without notice.
• Please use this service manual with referring to the operating instructions without fail. Please refer to the MODIFICATION NOTICE.
• Some illustrations using in this service manual are slightly different from the actual set.
Confidential
CAUTION IN SERVICING
SAFETY PRECAUTIONS
Caution in
servicing
NOTE FOR SCHEMATIC DIAGRAM
Electrical
INSTRUCTIONS FOR HANDLING SEMICONDUCTORS AND
OPTICAL UNIT
Mechanical
Accessing the Parts List
Logging in to New SDI and Accessing the Parts List
Accessing the Part List from the Model Asset Screen
PRINTED CIRCUIT BOARDS Parts Table
Downloading the Parts List as an Excel File
Repair Information
Revision History
Searching Part Numbers or Ref. Numbers
SERIAL NUMBER
Serial Number Organization
SKU Code of this Unit
CAUTION IN SERVICING.
Updating
Initializing This Unit
JIG FOR SERVICING
2
SAFETY PRECAUTIONS
The following items should be checked for continued protection of the customer and the service
◎ Make a safety check after servicing!
Check that all screws, parts and wires removed or disconnected when servicing have been put back
technician.
in their original positions, check that no serviced parts have deteriorate the area around. Then make
Leakage current check
Caution in
servicing
an insulation check on the external metal connectors and between the blades of the power plug, and
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or otherwise check that safety is ensured.
(2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance (Insulation check procedure)
from chassis to either side of the power cord is less than 460 kohms, the set is defective. Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and on the power.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's Using a 500V insulation resistance tester, check that the insulation resistance value between the inplug
power is in each state (on, off and standby mode), if applicable. and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is
1M Ω or greater. If it is less, the set must be inspected and repaired.
Electrical
CAUTION Please heed the following cautions and instructions during servic- CAUTION Concerning important safety parts
ing and inspection.
◎ Heed the cautions! Many of the electric and the structural parts used in the set have special safety properties. In most cases
Cautions which are delicate in particular for servicing are labeled on the cabinets, the parts and the these properties are difficult to distinguish by sight, and the use of replacement parts with higher rat-
chassis, etc. Be sure to heed these cautions and the cautions described in the handling instructions. ings (rated power and withstand voltage) does not necessarily guarantee that safety performance will
◎ Cautions concerning electric shock! be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and the
(1) An AC voltage is impressed on this set, so if you touch internal metal parts when the set is energized, parts list in this service manual. Be sure to replace them with the parts which have the designated part
you may get an electric shock. Avoid getting an electric shock, by using an isolating transformer and number.
Mechanical
wearing gloves when servicing while the set is energized, or by unplugging the power cord when
replacing parts, for example. (1) Schematic diagrams Indicated by the z mark.
(2) There are high voltage parts inside. Handle with extra care when the set is energized. (2) Parts lists Indicated by the z mark.
◎ Caution concerning disassembly and assembly! The use of parts other than the designated parts could cause electric shocks, fires or other dangerous
Through great care is taken when parts were manufactured from sheet metal, there may be burrs on the situations.
edges of parts. The burrs could cause injury if fingers are moved across them in some rare cases. Wear
gloves to protect your hands.
◎ Use only designated parts!
Repair Information
The set's parts have specific safety properties (fire resistance, voltage resistance, etc.). Be sure to use
parts which have the same properties for replacement. The burrs have the same properties. In particular,
for the important safety parts that are indicated by the z mark on schematic diagrams and parts lists,
be sure to use the designated parts.
◎ Be sure to mount parts and arrange the wires as they were originally placed!
For safety seasons, some parts use tapes, tubes or other insulating materials, and some parts are mount-
ed away from the surface of printed circuit boards. Care is also taken with the positions of the wires by
arranging them and using clamps to keep them away from heating and high voltage parts, so be sure to
set everything back as it was originally placed.
Updating
3
NOTE FOR SCHEMATIC DIAGRAM WARNING AND LASER SAFETY INSTRUCTIONS
WARNING: GB WARNING NL WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn gevoelig
Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD). voor elektrostatische ontladingen (ESD).
by the manufacturer. Careless handling during repair can reduce life Onzorgvuldig behandelen tijdens reparatie kan de
Caution in
levensduur drastisch doen verminderen.
servicing
drastically.
CAUTION: When repairing, make sure that you are connected
with the same potential as the mass of the set via a
Zorg ervoor dat u tijdens reparatie via een polsband
met weerstand verbonden bent met apparaat.
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) wrist wrap with resistance. Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
Keep components and tools also at this potential.
a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from
chassis to either side of the power cord is less than 460 kohms, the set is defective. F ATTENTION D WARNUNG I AVVERTIMENTO
WARNING: Tous les IC et beaucoup d’autres semiconducteurs
sont sensibles aux décharges statiques (ESD).
Alle IC und viele andere Halbleiter sind
empfindlich gegen elektrostatische
Tutti IC e parecchi semi-conduttori sono sensibili
alle scariche statiche (ESD).
DO NOT return the set to the customer unless the problem is identified and remedied. Leur longévité pourrait être considérablement Entladungen (ESD). La loro longevita potrebbe essere fortemente ridatta
écourtée par le fait qu’aucune précaution n’est prise Unsorgfältige Behandlung bei der Reparatur in caso di non osservazione della piu grande
NOTICE: a leur manipulation.
Lors de réparations, s’assurer de bien être relié au
kann die Lebensdauer drastisch vermindern.
Sorgen sie dafür, das Sie im Reparaturfall
cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM même potentiel que la masse de l’appareil et enfiler dem Massepotential des Gerätes verbunden collegato allo stesso potenziale che quello della
le bracelet serti d’une résistance de sécurité. sind. massa dell’apparecchio tramite un braccialetto a
ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P Veiller a ce que les composants ainsi que les outils Halten Sie Bauteile und Hilfsmittel ebenfalls resistenza.
INDICATES MICRO-MICRO FARAD. N INDICATES NANO FARAD. EACH VOLTAGE AND CURRENT ARE que l’on utilise soient également a ce potentiel. über ein Pulsarmband mit Widerstand mit auf
diesem Potential.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo potenziale.
Electrical
MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT
GB D
PRIOR NOTICE.
Safety regulations require that the set be restored to its original condition Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten.
and that parts which are identical with those specified be used. Der Originalzustand des Gerats darf nicht verandert werden.
Fur Reparaturen sind Original-Ersatzteile zu verwenden.
1. Parts indicated by "nsp" on this table cannot be supplied. Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkelijke
toestand wordt terug gebracht en dat onderdelen, identiek aan de
Le norme di sicurezza esigono che l’apparecchio venga rimesso nelle
condizioni originali e che siano utilizzati pezzi di ricambiago idetici a quelli
2. When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying. gespecifieerde worden toegepast. specificati.
3. A part ordered without specifying its part number can not be supplied. “Pour votre sécurité, ces documents F
4. Part indicated by "@" mark is not illustrated in the exploded view. doivent être utilisés par des
spécialistes agrées, seuls habilités à Les normes de sécurité exigent que l’appareil soit remis a l’état d’origine et
réparer votre appareil en panne.” que soient utilisées les pièces de rechange identiques à celles spécifiées.
WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts
Mechanical
recommended by the manufacturer.
LASER SAFETY
INSTRUCTIONS FOR HANDLING SEMICONDUCTORS AND This unit employs a laser. Only a qualified service person should
OPTICAL UNIT remove the cover or attempt to service this device, due to
possible eye injury.
Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential differ-
ence caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 M ohm) that is properly grounded to remove any static electricity
Repair Information
that may be charged on the body.
2. Ground for Workbench
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
Be sure to place a conductive sheet or copper plate with proper grounding (1 M ohm) on the work- OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN
bench or other surface, where the semi-conductors are to be placed. Because the static electricity MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
charge on clothing will not escape through the body grounding band, be careful to avoid contacting
AVOID DIRECT EXPOSURE TO BEAM
semi-conductors with your clothing
WARNING
<Incorrect> <Correct> Grounding Band
The use of optical instruments with this product will
increase eye hazard.
Repair handling should take place as much as possible with
1MΩ a disc loaded inside the player
Updating
CBA CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING
1MΩ ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL Å PNES UNNGÅ EKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
Conductive Sheet or
VARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN
Copper Plate
VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU
100301DM
4
Online Parts List
Accessing the Parts List Logging in to New SDI and Accessing the Parts List
(1) Click the URL link on the cover of the service manual. (1) Access New SDI from the URL below.
Caution in
servicing
Examples of display <http://dmedia.dmglobal.com>
(2) When the login screen is displayed, enter your username and password.
(3) Enter the 5 letters shown as the blue CAPTCHA code as single-byte characters.
If the text is unclear, click "Refresh" to change the CAPTCHA code, and enter it again.
Electrical
NOTE : If the web browser does not open automatically, copy the URL and paste it into the address bar
of the web browser and then press Enter. (4) Press the "Login" button.
(5) When the Home screen is displayed, click "Advanced Search".
Mechanical
(2) When the login screen is displayed, enter your username and password. (6) Enter the following search conditions and click "Search".
(3) Enter the 5 letters shown as the blue CAPTCHA code as single-byte characters. Keyword : Model name Brand : brand name Asset Type : Part list
If the text is unclear, click "Refresh" to change the CAPTCHA code, and enter it again.
Repair Information
(7) Click the model name when the search results are displayed.
(4) Press the "Login" button.
Updating
5
Accessing the Part List from the Model Asset Screen Downloading the Parts List as an Excel File
(1) Display Model Asset from New SDI. (1) Displays the Parts List. Click the Download icon.
Caution in
servicing
(2) Click the section displayed as ▼ Link to Part Lists under the model name.
Electrical
NOTE : If the ▼ Link to Parts List section is not displayed, download the parts table from the Asset list.
Mechanical
PRINTED CIRCUIT BOARDS Parts Table Revision History
(1) Display the Parts List. Click the PCB name in the blue bar to display the parts list for the board. (1) Click "Revision history" in the blue bar.
Repair Information
The following details are displayed.
Updating
Factories : Factory number
Ver : Version number after revision if changes were made to the parts list
Date : Date of changes
6
A1
SERIAL NUMBER
Searching Part Numbers or Ref. Numbers Serial Number Organization
You can search a Parts List for part numbers or Ref. numbers. The 14-digit serial number that contains the code of the manufacturing plant and the manufacturing
Caution in
servicing
(1) Enter the part number or Ref. number in the search window of the Parts List, and press the search date.
button.
(2) The search results are displayed. 14 digits
The name of the sheet in which the search part is used and the part’s line are displayed.
Electrical
The last Month
(3) Next, click the "Sheet" section of the search results. 2digit of year (01 ~ 12)
Mechanical
Product SKU SKU Code
(4) The Board Part Table opens and the line on which the searched part number appears is highlighted. RCDM41BKE2 AUG
RCDM41SPE2 AUH
RCDM41DABBKEK AUJ
RCDM41DABSPEK AUK
RCDM41BKE1C AUP
Repair Information
RCDM41K AUM
RCDM41SP AUN
Updating
7
CAUTION IN SERVICING.
Initializing This Unit
Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the
Caution in
servicing
digital PCB.
1. Press the power operation button to turn off the power, and remove the AC plug from the socket.
2. While holding down buttons the "SOURCE" and "8" buttons simultaneously, insert the AC plug to
turn the power on.
* This unit can also be initialized by holding down the button "SOURCE" and pressing the power
button for 3 seconds or more while on standby.
3. "INITIALIZE" is displayed.
* The unit is initialized.
* Unplug the AC plug to cancel this mode.
4. After 5 seconds, switch to the normal mode.
Electrical
NOTE: • If the unit fails to enter the service mode in step 3, repeat the procedure from step 1.
• Initializing the device restores the customized settings to the factory settings. Write down
your settings in advance and reconfigure the settings after initialization.
RCD-M41DAB
Mechanical
X SOURCE 8
Repair Information
d JIG FOR SERVICING
When repairing the board, use an extension jig cable (300mm FFC cable connecting the CD mechanism
to the main board) for the JIG.
Updating
8
ELECTRICAL
SCHEMATIC DIAGRAMS LEVEL DIAGRAM
Caution in
servicing
SCH01_CPU HEADPHONE
SCH02_DSP SPEAKER
SCH03_DIR
SCH04_CNT1
SCH05_INPUT
BLOCK DIAGRAM
SCH06_CNT2
SCH07_DAB
POWER DIAGRAM
Electrical
SCH08_FRONT
SCH09_SPK
SCH10_AMP WIRING DIAGRAM
SCH11_ST_BY
g SCH12_ST_BY-2
SEMICONDUCTORS
PRINTED CIRCUIT BOARDS 1. IC's
Mechanical
2. FL DISPLAY
MAIN, INPUT, CNT 1, CNT 2, REGULATOR 1,
3. Remote Code Table
REGULATOR 2, DAB EK Only, GUIDE R, GUIDE F, SUB
GUIDE F , GUIDE
SPK, FRONT, AMP, ST_BY
g ST_BY-2
Repair Information
Updating
9
SCHEMATIC DIAGRAMS
SCH01_CPU
Caution in
servicing
161129
Added R217 47 ohm
Connected BT_RX line
+3V3_ST
A3 A2
JTDI
CD_P_ON
JTDO
JTMS
JTCK
VFD_RST
VFD_CE
VFD_DA
TU_SEN
MAIN_MUTE
AUDIO_MUTE
BT_RX
JTRSTX
SW_MUTE'
VFD_CLK
SPK_OPTIMIZER
TO 3A TO 2A
R101 -
4K7 AD_MONI1
R392 R102 -
160928
D101
160928
FLAG2
0
R103 10K
D101
Q122 FLAG1
KRC102S R104 -
+3V3_ST AMP_PROT
C102
47/6.3-Z8155
1N-J
A4
47
47
47
47
47
47
47
47
47
47
47
47
DIR_DI
0
R315
10K
10K
10K
DIR_DO
R105
R106
R107
R109
R110
R111
R112
R217
R113
R114
R115
R116
R117
R118
DIR_CE
TO 4A
Added R233, R235(10K) R233 10K
FPC101
DIR_CLK
R119
R120
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
R121 33K
+3V3_ST R122 0 DIR_RST
SPK_OPTIMIZER
BT_RX
JTCK
VCC
TU_SEN
JTMS
JTRSTX
JTDO
JTDI
VFD_RST
{pin78}
MAIN_MUTE
{pin73}
{pin72}
VFD_CE
VFD_DA
VFD_CLK
+3V3_ST
AUDIO_MUTE
VCC KEY1
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
DGND R123 0 R124 0 DIR_INT1
VOL/DIR/DAC PART
TU_INT TU_INT UPDATE_RX
2
DGND DGND EX_INTERRUPT
R125 0 KEY_EXTINT 60.KEY1 UPDATE_TX R126 0 UPDATE_TX DIR_INT2
3
R127 0 R128 0 R129 0
VFD_3V3 VFD_3V3 +3.3VD'' DIR_INT1 DIR_INT1
59.UPDATE_RX KEY2 KEY2
79.CD_P_ON
4
80.VSS
VOL_CE
R130 0 R131 33
FRONT PART
VFD_RST VFD_RST DIR_INT2 DIR_INT2 DAB_TU_ON DAB_TU_ON
5
VFD_CE VFD_CE LED_RED
R132 0 RED_LED DAB_DA/TU_SDA R133 33 DAB_DA/TU_SDA
VOL_CLK
47/6.3-Z8155
6
VFD_CLK VFD_CLK LED_GREEN
R134 0 GREEN_LED DAB_CLK/TU_CLK R135 33 DAB_CLK/TU_CLK VOL_DA
7
R357 10K R136 0
Electrical
VFD_DA VFD_DA BT_P_ON BT_P_ON TU_RST TU_RST DAC_DEMP
8
R137 33 IC101
C105
C106
RMC
100N-K
100N-K
1N-J
RMC RMC RMC AVSS
C103
C104
MB9AF344 DAC_MUTE
KEY1 KEY1 AMP_PROT
R138 22K AMP_PROT AVRH
20 19 18 17 16 15 14 13 12 11 10
DAC_FLT
KEY2 KEY2 PROT_V PROT_V AVCC L101 BLM18PG221SN1
R139 100K R140 33 L102 BLM18PG221SN1 DAC_FMT
EX_INTERRUPT EX_INTERRUPT BT_INT BT_INT POWER_DOWN PWR_DN
R216 100K R142 33
VOL_UP VOL_UP VOL_CE VOL_CE DIR_CE DIR_CE SPK_OPTIMIZER
R141 33 R144 33 160922
VOL_DOWN VOL_DOWN DIR_CLK
9A
VOL_CLK VOL_CLK DIR_CLK SET OPTION
R143 33 AUDIO_MUTE
H/P_DET H/P_DET VOL_DA VOL_DA DIR_RST R146 33 D126 DIR_RST
RED_LED LED_RED DAC_DEMP
R145
R147
33
33
DAC_DEEMP
42.SET_OPTION CD_RESET R148 33 LBAS16HT1G
CD_RST
SET R157
TO A9 H/P_MUTE'
22.H/P_MUTE
41.VCC R150 33 EK(UK) 33K(2.5V)
21.H/P_DET
GREEN_LED LED_GREEN DAC_MUTE DAC_MUTE CD_TX CD_TX MAIN_MUTE
R149 33 R152 33
A5
31 EEPROM_CLK
DAC_FLT DAC_FLT CD_RX CD_RX E2(EU) 1K8(0.5V) SW_MUTE'
32 EEPROM_DA
33 SMPS_P_ON
FPC101 R151 33 R154
VOL_DOWN
47Kohm->open
1.0-11-17P
TO 5A
DAC_FMT DAC_FMT
29 VOL_UP
E3(NA) 4K7(1V)
35 DIR_DO
R153 33 DAB_TU_ON
34 DIR_DI
TO FPC502
R155 47K
10K
28 INITX
25 VCC
36 MD1
37 MD0
24 VSS
40 VSS
26 X0A
27 X1A
VSS
R156 -
X0
39 X1
E1C(CHN) 8K2(1.5V) DAB_DA/TU_SDA
23 C
R157
33K
161208
21
22
30
38
R156
K(JP) 15K(2V) DAB_CLK/TU_CLK
4K7
4K7
4K7
-
4700P-K
TU_INT
C108
220/6.3
160919
47K
R162 1M TU_RST
R158
R159
R160
R161
32.768KHz
C109
33
33
33
33
33
100K
X102
R163
CN112
47/6.3-Z8155
0
0
0
0
0
X101
1N-J
IC103 TU_SEN
4 1
10K
10K
10K
GND VOUT RESET 4M(20P)
CW24C16CDR
C112
33P-J
33P-J
C107
C110
C111
VDD
R164
R165
R166
R167
R168
R169
R170
R171
R172
R173
R174
R175
1
PWR_DN
3 2
TO JTAG
JTCK JTCK NC VDD
C113
2
10K VCC NC PWR_ON 160919
5 6 7 8
4 3 2 1
R176
R177
R178
R179
R180
JTDI JTDI CN108
10K
10K
3
DGND
WP NC
PROT_V 1.0-16-7PB-2
JTDO JTDO R318 10K
100N-K
4.7/25-Z8154
20P-J
20P-J
IC102 C117 EEPROM_SCL SCL NC
C115
C116
C118
H/P_MUTE
H/P_DET RESET RESET RESET
C114
JTMS
1
JTMS
RESET
5
BU4827F 1U-K
100/6.3-Z8156
EEPROM_SDA SDA GND
JTRSTX +3V3_ST +3V3_ST +3V3_ST
2
JTRSTX
6
H/P_MUTE'
L103 BLM18PG221SN1 UPDATE_TX UPDATE_TX UPDATE TX
3
DGND
PWR_ON
7
VOL_UP
DIR_DO
L104 BLM18PG221SN1
100N-K
DIR_DI
C119 C120 UPDATE_RX UPDATE_RX UPDATE RX
4
C121
C122
MD0
J150 0 J146 0 VOL_DOWN
R389
100P-J 100P-J DGND DGND DGND
5
+3.3VS 4K7
MD0 MD0 UPDATE MD0
Mechanical
NC
7
Q120
+3V3_ST
+3V3_ST
A_-12V
A_-12V
AD_MONI1
100N-K
FPC102
A
PD
C
LD
Q119
C125
KRC102S
+3.3VS
X103
+3.3VS
VC 161207
+3.3VSD
J147 0 J148 0
VCC C126, C127 : 15pF->22pF L106 L105
2
100/6.3-Z8156
E BLM18PG121SN1D-BD121 BLM18PG121SN1D-BD121
100N-K 100/6.3-Z8156
+3.3VD'' +3.3VD'' MOT_GND DGND
A_+12V
A_+12V
SPK_OPTIMIZER
SPK_OPTIMIZER
D D LD 22P 22P
4
C128
100N-K
100N-K
100N-K
100N-K
100N-K
100N-K
L108 1N-J
TP101
TP102
TP104
TP105
100N-K
68/25
+3.3VSD
100/6.3-Z8156
A A
5
TP106
C123
DGND
(105¡É)
10N-K
B B 161205
TO CD PICK-UP
6
-
R183 18
680P-K
C345 - C C R182 Deleted L109
7
R184 18
C132
2M 161201
C135
C136
C137
C138
C139
C140
C133
C134
C129
C130
161207
TP103
F F
8
C131
DGND
47K-F
47K-F
33K-F
33K-F
33K-F
33K-F
C124
TP107
9
R186 18
161201
LD
10
C141
DGND
DGND
Q101 2700P-J
VR
A7
11
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
R187 10-J KTA1504S
C142 L110
R194
PD
12
R188
R189
R190
R191
R192
R193
PD 0
EQO
1K
XO
TEST6
TEST5
TEST4
FRI
AVDD2
TEST_IN
DVDD
MONO1
MONO0
MONO1
MONO0
AGND2
TEST_OUT
DGND
J128 0 6800P-K XI
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
J132 0
1
F+
100N-K
100N-K
100N-K
100N-K
100N-K
+3.3VD'' D3V3'''
13
FP AVDD1
10/16-Z8154
2
T-
14
TN
C336 10N-K TP108
56K-F
J141 0 C337 - BD FLAG3
R195
R196
3
T+
15
TP
C341 10N-K TP109 L111 L112
C155
J140 0 C339 10N-K VBIAS FLAG2 FLAG2 IC106
DIR PART
4
F- 0 0
16
FN AP7361-ADJ
C342 -
C146
C147
C148
C149
C150
J142 0 C340 10N-K AM5888S_MUTE AGND1 FLAG1 FLAG1 TP110 D_5V
5
C351
TO 7A
-
1N-J
10K
12K7-F 6K8-F
8K2-F
10/16-Z8154
J143 0 C343 -
0.22/50
R198
R197
E FLAG0
R230 R229
6
C143
R199
C352 - TP111
J144 0 C344 - IC105 F DGND
7
IC104
47N-K
C338 1N-J
-
0
J145 0
3.3/35
AM5888S
C144
LBAS16HT1G
C154
PD BU9546KV TEST3
R227
8
J134 0 R201 R200 1K LD TEST2
D102
9
AGND
DGND
22 23 24 25 26 27 28
FDOUT
DGND1
DGND
VINFC MUTE
J135 0
7 6 5 4 3 2 1
C145 100N-K-16V
C151
C152
10K ASY TEST1
16 15 14 13 12 11 10
J136 0 TRB_1 BIAS R202 470 D3V9_BT R231
SP+ SP+ R203 12K PCO TEST0
Repair Information
6
J137 0 R204
REGO2 VINTK
SP- SP- FCO VDD_CORE 6K8-F
J138 0
5
REGO1 NC R206 0
DVDD
DIN/OUT MCK
DOUTA LRCK
SL- SD- R207 3K3 TDOUT R213 0
TO CD MECHA
J119 0 161208
3
AVDD
CD_LM+ FWD VINLD R208 0 DGND
26 VDD_CORE
SDOUT IC106 LM1117 -> AP7361
23 SUBDATA
J118 0 DGND R214 0
30 RESETB
22 SUBSYQ
R/W
BUSY
SUBCK
WFCK
2
31 XBUFO
Added R227(10K), R229(2K-F)
32 DGND
29 CLK88
27 DGND
CLVOUT
J139 0 LIMIT S/W CD_LIMIT
28 CLK
1
R230(12K7-F), R231(4K7-F)
29
30
+3V3_ST
J149 0 C153 100N-K C151(100N->47N)
R210
17
18
19
20
21
24
25
CN101 161205
10K
C154(100N->1N)
VDD_CORE
J120 0
R225
R223
10K
10K
DGND
Nearby micom
15 16 17 18 19 20 21
Vcc1 VCTL
D102(LBAS16HT1G->OPEN)
14 13 12 11 10 9 8
J121 0 161201
+3.3VSD D105
LOAD+ VOTR- NC Added coutermesure circuit
J122 0 for IN/OUT short test of 5V regulator
LOAD- VOTR+ Vcc2
J123 0 LBAS16HT1G
R211
R212
100/6.3-Z8156
10K
J131 0
10K
C160
TP115
SD- Q124
J125 0 CLOSE S/W CD_SW_A VOSL- VOLD+
C158 100N-K
C157
100N-K-16V
5
KRC102S
R220
TP112
TP113
TP114
DGND FN VOFC- VOTK-
J151 0 15K
4
Q123
KRC102S
J124 0 LOAD- LOAD-
100N-K-16V
C159
33
2
TP116
R221
3K9
AGND
AGND
LOAD+ LOAD+
CP101
1
C162
J129 0-3216 100N-K
R215
CN102
J130 0-2012
A0 A6 D_5V D_5V
ST-BY PART
TO DSP PART
J153 0-3216
DIR/DAC/VOL PART
CD_LIMIT DGND1 DGND1
J154 0-3216
A_-12V A_-12V
CD_SW_A
TO 6A
DGND
DGND
A_+12V A_+12V
CD_SW_B
MOT_GND MOT_GND
CD_RST +8VM +8VM
+3V3_ST +3V3_ST
CD_TX
J103 0 J105 0 J108 0
DGND
CD_RX
J104 0 J106 0 J109 0 DGND
J107 0 J110 0
TO 0A DGND CP101
9P_WIRE(2.5mm) TO CN512
DGND
DGND
J117 0
161201
DGND
DGND
CD_DIN_OUT
CD_SUBSYQ
DGND
DGND
CD_BUSY
CD_DATA
CD_LRCK
CD_MCK
CD_DCK
CD_RES
PROT_V
CD_16M
CD_RW
SDOUT
FDOUT
FLAG2
FLAG1
SP+
CD : RFEQ
SP-
TN
TP
Updating
VREF
BT_INT
CD_RES
CD_SUBSYQ
CD_BUSY
CD_MCK
LD_CHK
D3V9_BT
CD_16M
CD_DCK
CD_LRCK
CD_DATA
CD_DIN_OUT
CD_LM+
CD_LM-
+3V9_ST
CD_RW
AM5888S_MUTE
C164
CH_GND
DGND
100N-K
100N-K
100N-K
100N-K
100N-K
100N-K
CH_GND
CH_GND
CH_GND
C175 100N-K
DGND
DGND
MOT_GND
DGND
DGND
100/6.3-Z8156
100N-K-16V
C165
C169
DGND
MOT_GND
C170
C171
C172
C173
C174
TO DSP PART
TO 1A
DGND
DGND
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
10
SCH02_DSP
Caution in
servicing
3A 1A 2A
TO A3 TO A1 TO A2
BLM18PG121SN1D-BD121
TO CPU PART
0A
DSP Part
+3V3_BT''
TO A0
AM5888S_MUTE
CD_DIN_OUT
CD_SUBSYQ
161201
AD_MONI1
D3V9_BT1
CD_SW_A
CD_SW_B
CD_BUSY
CD_P_ON
CD_DATA
CD_LRCK
BT_P_ON
CD_LIMIT
CD_MCK
CD_DCK
+3V9_ST
Added connection for CD solution
CD_RST
CD_RES
CD_LM+
LD_CHK
CD_16M
100/6.3-Z8156
CD_LM-
CD_RW
BT_INT
CD_RX
CD_TX
BT_RX
FLAG2
FLAG1
L113
100N-K
10K
10K
C176
C177
R218
R219
VDD 161201
9 10
R222 47 Added connection for CD solution
RESET BT_RST
RTS R224 47 BT_CTS R245 100
8
AD_MONI1 AD_MONI1'
CTS R226 47 BT_RTS R247 100
7
R228 47
TO BT UNIT
FLAG2 FLAG2'
TXD BT_RX
6
FLAG1
R248 100 FLAG1'
DGND
5
R232 47
RXD BT_TX
U T R P N M L K J H G F E D C B A R234 10
Electrical
SF_CS1 SF_CS
DGND R252 4K7
3
DGND DAC_SCLK2
R237 47 U1 T1 R1 P1 N1 M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 B1 A1 R236 10
SCL BT_SCL SF_DI1 SF_DI
2
R239 47 AM5888S_MUTE 1 AD_MONI1' CD_LRCK1 CD_16M1 BT_RX1 BT_TX1 +3.3V1 DAC_SCLK2 FLAG1' FLAG2' CD_RES1 AM5888S_MUTE R240 10
SDA BT_SDA SF_DO1 SF_DO
1
+3.3V1
R241 4K7 +3V3_BT''
PGPC08 PGPC07 PGPC04 PGPC03 PGPB15 PGPB14 PGPB11 PGPB10 PGPB07 PGPB06 PGPB03 PGPB02 PGPA14 PGPA13 PGPA10 PGPA09 PGPA08
SF_CLK1
R243 10 SF_CLK
FPC103 R244 100
CD_RES CD_RES1
U2 T2 R2 P2 N2 M2 L2 K2 J2 H2 G2 F2 E2 D2 C2 B2 A2
SPDIF
R246 10 SPDIF1 2 CD_SUBSYQ1 CD_DATA1 BT_RTS1 BT_CTS1 CD_LIMIT1 BT_INT SPDIF1
PGPC09 PGPC06 PGPC05 PGPC02 PGPC01 PGPB13 PGPB12 PGPB09 PGPB08 PGPB05 PGPB04 PGPB01 PGPA15 PGPA12 PGPA11 PGPA06 PGPA07
RTCK1
R250 10 RTCK
U3 T3 B3 A3 TDO1
R253 10 TDO
3 R255 10
BT_SDA1 BT_SDA
CD_DIN_OUT
R256 100 CD_DIN_OUT1
PGPC10 PGPC11 PGPA05 PGPA04
TCK1
R257 10 TCK
U4 T4 P4 N4 M4 L4 K4 J4 H4 G4 F4 E4 D4 B4 A4 BT_SCL1
R258 10 BT_SCL
C_RX
R259 100 C_RX1 4 1.2V DGND +3V3_BT'' CD_DCK1 CD_LM-1 CD_SW_B1 CD_SW_A1 1.2V CD_BUSY1 C_TX1 CD_DIN_OUT1 +3V3_BT'' DGND +3.3VA R260 10
TMS1 TMS
R261 100 VDD12INT VSS12INT VDD33IO PGPC00 PGPC15 PGPC13 PGPC12 VDD12INT PGPD15 PGPD14 PGPD04 PGPB00 VDD33IO VSS33ADC VDD33ADC
C_TX C_TX1 160919 +3V3_BT
R262 1K IC108
CD_BUSY CD_BUSY1
U5 T5 P5 N5 L5 J5 G5 E5 D5 B5 A5 C198
R263 100 LD_CHK 100N-K
CD_LIMIT CD_LIMIT1 5 +3.3VU DGND CD_LM+1 DGND C_RX1 DGND LD_CHK R264 10
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
VDD VSS
1
100 TDI1 TDI
CD_SW_A
R265 CD_SW_A1
VDD331USB PUID20 PGPE00 VSS33IO PGPC14 VSS12INT PGPD13 VSS33IO PAIN[4] PAIN[0] PAIN[1] D0 DQ0 DQ15 D15
R266 10
2
R267 100 NTRST1 NTRST C199 VDDQ VSSQ
100N-K
3
BT_TX BT_TX1
U6 T6 P6 D6 B6 A6 D1 D14
R268 100 DQ1 DQ14
4
CD_SW_B CD_SW_B1 D7
6 +3.3VU CD_RX1 RTCK1 D2 DQ2 DQ13 D13
5
BT_RX
R269 100 BT_RX1
VDD330USB PUVBUS20 PGPE01 PRTCK PAIN[3] PAIN[2] D6 C197
VSSQ VDDQ
100N-K
6
CD_LM+
R270 100 CD_LM+1 D5 D3 DQ3 DQ12 D12
7
U7 T7 P7 N7 E7 D7 B7 A7
R271 100 D4 DQ4 DQ11 D11
8
BT_CTS BT_CTS1 DGND CD_TX1 BT_RST1 TDO1 TCK1 +3.3VU D4
7 C267
R272 100 PUDP20 VSS330USB2 PGPE02 PGPE03 PTDO PTCK VDD33USB1 PUDN11 100N-K
VDDQ VSSQ
9
CD_LM- CD_LM-1 D3
D5 D10
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
DQ5 DQ10
D2
BT_RTS
R273 100 BT_RTS1
U8 T8 P8 D8 B8 A8 D6 DQ6 DQ9 D9
D1 VSSQ VDDQ
C272
R274 330 8 44.2R TMS1 DGND 100N-K
Mechanical
CD_16M CD_16M1
W9812G6KH
PUDN20 PRTUNE20 PGPE04 PTMS VSS33USB11 PUDP11 D0
D7 DQ7 DQ8 D8
CD_LRCK
R275 470 CD_LRCK1 C268 VDD VSS
D15 100N-K
CD_DCK
R276 470 CD_DCK1
U9 T9 P9 N9 E9 D9 B9 A9 LDQM LDQM NC
9 D14
CD_DATA
R277 470 CD_DATA1
+3V3_BT'' DGND 1.2U DGND 1.2V TDI1 DGND 1.2V WEN WE UDQM UDQM
VDD33OSCVSS331USB2 VDD12USB2VSS12USB20 VDD12INT PTDI VSS12INT VDD12INT D13 CASN CAS CLK SDCLK
CD_SUBSYQ
R278 100 CD_SUBSYQ1
RASN RAS CKE SDCKE
A8 L114
U10 T10 P10 D10 B10 A10
D12
SDCSN CS NC AD12
R280 D11
R285 10
TO DIR PART
X4MI 1.2V NTRST1 DGND +3V3_BT'' BA0 AD11
CD_SPDIF' SPDIF BS0 A11
47 BD121 47K PXI VDD12ALIVE PGPE05 PNTRST VSS33IO VDD33IO D10 BA1 BS1 A9 AD9
+3V3_BT''
TO 8A CD_RX
R282 100 CD_RX1
U11 T11 P11 N11 E11 D11 B11 A11
D9 AD10
AD0
A10/AP
A0
A8
A7
AD8
AD7
11 X4MO D8
CD_TX
R283 100 CD_TX1
DGND BT_SCL1 BT_SDA1 SF_DI1 SF_CS1
AD1 A1 A6 AD6
PXO PTEST PGPE06 PGPE07 PGPD02 PGPD03 PGPA02 PGPA03 BA1
BT_RST
R284 100 BT_RST1 AD2 A2 A5 AD5
BA0 AD4
U12 T12 P12 D12 B12 A12 AD3 A3 A4
FPC104
AD10 C269 VDD VSS
12 DGND CD_RST1 1.2P SF_DO1 SF_CLK1
100N-K
C_TX R286 47 X4MI
VSS33OSC PRESETN VDD12PLL PGPD01 PGPA01 PGPA00
TO BT DEBUG
C_TX AD2
C_RX R287 47 C_RX X4MO
AD1
R319 10K 160922 U13 T13 P13 N13 L13 J13 G13 E13 D13 B13 A13
+3V3_BT''
CASN1
R299 100 CASN
R296 100 14
CD_MCK1 CD_RW1 +3V3_BT'' AD4 1.2V BA1 +3V3_BT'' D5 D4
CD_RW CD_RW1
PGPE[12] PEXTSRC0 VDD33IO PAD[4] PGPD05 PGPD07 PGPD08 VDD12INT PGPD09 PGPD10 PGPD12 PSDBA[1] VDD33IO PD[5] PD[4] R301 100
W25Q16JVSSIQ_
FPC105 SDCSN1 SDCSN SF_CS
100N-K
1
160919
R302
R303
R304
R305
C196
SF_DO
IC109
DO
2
7
VDD AD3
1
Repair Information
/WP
3
6
TMS TMS
2
15 LDQM
R307 44R2-F D2 D3
GND
44.2R DGND
DI
4
5
NTRST NTRST PWAKEUP PEXTSRC1 PD[2] PD[3]
3
UDQM
TCK TCK
4
BT_P_ON SF_DI
R308 100
TO MLC3730 DEBUG DGND U16 T16 R16 P16 N16 M16 L16 K16 J16 H16 G16 F16 E16 D16 C16 B16 A16
SDCKE1 SDCKE
5
SF_CLK
R309 100
TDO TDO 16 SDCLK1 SDCLK
6
3.0R AD9 AD8 AD5 SDCKE1 LDQM AD3 RASN1 WEN1 AD2 BA0 D8 D11 D12 D1 D0 R310 4K7
RTCK RTCK PRTCXI VDD30RTC PAD[9] PAD[8] PAD[5] PSDCKE PSDDQM[0] PAD[3] PSDRASN PSDWEN PAD[2] PSDBA[0] PD[8] PD[11] PD[12] PD[1] PD[0]
7
AD4
TDI TDI
8
AD5
DGND U17 T17 R17 P17 N17 M17 L17 K17 J17 H17 G17 F17 E17 D17 C17 B17 A17
10 9
AD12 AD11 AD7 AD6 SDCLK1 UDQM SDCSN1 CASN1 AD0 AD1 AD10 D9 D10 D13 D14 D15 AD6
RST CD_RST 17
DGND
PRTCXO PAD[12] PAD[11] PAD[7] PAD[6] PSDCLK PSDDQM[1] PSDCSN PSDCASN PAD[0] PAD[1] PAD[10] PD[9] PD[10] PD[13] PD[14] PD[15]
10P-J
100K
10P-J
D127 AD7
LBAS16HT1G
AD8
IC107
C178
C179
AD9
MLC3730
R311
AD11
AD12
DGND
+3V3_BT''
161201
+3V3_BT
X4MO
X4MI
CD_P_ON
BT_P_ON
+3V3_ST
BD121
BD121
L127
+3V3_BT''
+3V3_BT''
R312
L128
1.2U
1.2V
+3.3VU
+3.3VS
+3.3VA
1.2V
1.2P
R317
L117 L118 X106
1K
BD121
100N-K-16V
4 5 6
3 2 1
4 5 6
3 2 1
For DPP
100N-K-16V
SMFB14
M7
1U-K
1U-K
100N-K-16V
BD121 BLM18PG121SN1D-BD121
C181
0 4K7
100N-K
100N-K
100N-K-16V
C180
C200
4
C182
C321
C184
C185
IC112
100N-K-16V LM1117-1.2
C186
3
D123
161207
9P-J
C323
C322
C202
C201
1N-J
1N-J
C192
9P-J
DGND
DGND
DGND
100N-K
100/6.3-Z8156
DGND
C193
DGND
C195
C191
D3V9_BT
161201
Changed D123 value C194
Updating
LBAS16HT1G ->0-2012 100/6.3-Z8156
DGND
DGND
170109
Changed D123, D124 value
D123 : 0-2012 -> LBAS16HT1G
D124 : LBAS16HT1G -> 0-2012
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
11
SCH03_DIR
Caution in
servicing
4A
DIR/DAC/VOL PART
H/P_MUTE
AUDIO_MUTE
DIR_INT1
100N-K 22/6.3-Z8154
DIR_INT2
DIR_DI
DIR_DO
DAC_BCK
DIR_DO
DAC_MCK
DAC_LRCK
DAC_DATA
C204 C203
DIR_DI AMP_PROT
DIR_RST
DIR_CLK DGND
DIR_CE
33
33
33
33
0
0
AMP_PROT
0(AR)
R331
DAC_DEMP
R332
C205 IC114
R325
R326
R327
R328
R329
R330
-
- LM1117-3.3
DAC_FLT
24
23
22
21
20
19
18
17
16
15
14
13
DAC_FMT
100/6.3(6.3*11, PVO)
100N-K
0(AR)
100N-K
R336
R340 IC115
MDI/SDA
R334 0
10/16-Z8154
NDO/ADR0
LBAS16HT1G
DAC_MUTE DIR_CLK MPIO_B1
36 35 34 33 32 31 30 29 28 27 26 25
DGND
9 10 11 12
SCKO
MPO1
MPO0
DVDD
DOUT
NJW1194A
-
LRCK
BCK
R335 0 IC124
C208
D104
DIR_CE PCM5100A
10N-K
MPIO_B0
220/50(10*16)-RFG
VOL_DA
C212
C213
IN1_R C211
-
IN1_L
32
R338 0
CPU PART
6A
C207
100N-K
C320
25.MC/SCL 47/50(6.3*11)-RFO
C206
MODE MPIO_C3
R341
C216 C210
C209
VOL_CLK 26.MS/ADR1 DAC_R
14.MPIO_B3
13.MPIO_B2
DVDD CPVDD DAC_R' DAC_L DAC_L'
19 20
31
R339 0
2
J152 2R2U-K-16V
-
CD_SPDIF' RXIN7/ADR1 MPIO_C2 47/50(6.3*11)-RFO
D106
C214
DGND CAPP TU_R' TU_R TU_L TU_L'
30
VOL_CE DGND1
-
RXIN6/ALRCKI0 MPIO_C1 C215 0 IC116
100/35(10*12.5)-UFG
100N-K
100/35(10*12.5)-UFG
LDOO CPGND AUX_R' AUX_R AUX_L AUX_L'
15 16 17 18
29
R342 0 R346 LM7808RTR
4
PROT_V DAB_SPDIF' RXIN5/ABCKI0 IC127 MPIO_C0 R343 0 C219
7
PCM9211 0(AR) DAC_MUTE XSMT CAPM GND A_+12V
28
GND
5
RXIN4/ASCKI0 MPIO_A3 2R2U-K-16V
PWR_ON R344 0 C220 C221
100N-K
100N-K
6
330(AX)-AMRS
100/25(TOSHIN)
DAC_FMT FMT VNEG
27
R345 0
LBAS16HT1G
5
100/16-Z8157
6
OPT2 R348 100/16-Z8157
Electrical
RXIN3 MPIO_A2 R347 0
5
PWR_DN GND VOL_L1''
C225
DAC_LRCK LRCK OUTL DAC_L' GND
26
6
7
38.GNDRX
D107
C223
RXIN2 MPIO_A1
-
37.RXIN0
2.NPCM/INT1 R349 0
4
R451 0
C231
C230
R351 DAC_DATA DIN OUTR DAC_R' VOL_R1'' R_OUT
12 13 14
25
MAIN_MUTE R353 L_OUT
8
1.ERROR/INT0
DIR_RST
C222
C224
xRST MPIO_A0 R352 0 R350
3
1K 0 R452 0 DAC_BCK BCK AVDD V- ADR1
24
8
9
DAB_TU_ON OPT1 RXIN1 DIR_INT2 330(AX)-AMRS D108
R354 0 R355 100 C229
2
45 AGNDAD
R356 R453 0 DAC_MCK SCK AGND AGND DATA ADR0
46 VCCAD
10
23
LBAS16HT1G
9
44 VCOM
10/50-Z8156
41 AGND
100K
VDDRX DIR_INT1
48 VINR
47 VINL
DAB_DA/TU_SDA
C228
C226
C227
R358 0 R359 100
42 VCC
40 XTO
43 FILT
2N2(EB)-100V
2N2(EB)-100V
IC117
100N-K
R454 0
39 XTI
0 DAC_FLT FLT DEMP CLK V+
11
10
11
22
100N-K
LM7908RTR
DAB_CLK/TU_CLK R360 100
100N-K-16V
LATCH V- A_-12V
37
38
12
21
100N-K-16V
C239 D109
C232
GND GND
C243
100N-K
C238
13
20
TU_INT DAC_DEMP
R456
R361
3300P-K LBAS16HT1G
C240
1
C234
C235180P-J
C236180P-J
C237180P-J
14
19
3300P-K
TO A6
TU_RST C253 R362 VOL_DA
22/6.3-Z8154
CPU PART
100N-K
C245
100N-K
100N-K 0 C246
100/25(TOSHIN)
100N-K
15
18
100N-K
LBAS16HT1G
22/6.3-Z8154
TU_SEN
C233
R370 VOL_CLK
22/6.3-Z8154
16
17
C254
C250
C242
D110
- R363
R365
D3V3
AMP_PROT VOL_CE C247 C248
C244
R370 0ohm->open
R366
-
680
4K7
160919
R364 4.7/25-Z8154 4.7/25-Z8154
C241
C249
4700P-K
1M
C255
4K7
24M576(10P)
SPK_OPTIMIZER
161130
X109
TO A4
Changed GND
R367
1 2
0
C256
68N-K-16V
NET00162
C252
161130
22/6.3-Z8154
C258
8P-D
R462 0
8P-D
C257
R368 R461 0
AGND DGND1
0
R369 -
A3V3
BD600
IC118
L120 LM1117-3.3
L121 L122
BD600 0
D_5V D_5V
100N-K
100N-K
100/25(6.3*11)-RFO
LBAS16HT1G
10/16-Z8154
DGND
D114
C264
7A
VOL_R1''
VOL_L1''
TO A7 C261
C262
C263
DSP PART
L123
0
D3V3''' DGND
Mechanical
22/50(6.3*5.3)-RVG 22/50(6.3*5.3)-RVG
8A CD_SPDIF'
TO A8 SPK_OPTIMIZER
C271 J101
C270 47/50(6.3*11)-RFO 470(AX)-AMRS
35MU104KZ22012 R371 CP102
47K-SUSUMU
12K C276 CP102
47K(SUSUMU)
C273 100N-K Q103
C280 12P_WIRE
1/50-Z8155
35MU104KZ22012 KRA103S
R374
-
R378
470K
47K-SUSUMU
C277
R380
R376
-
AMP PART
33K MAIN_MUTE MAIN MUTE
R382
C278
5 6 7 8
R381
56K
R383
MUTE_B+
HFD27/012-S
-
LBAS16HT1G
AMP_PROT
RLY101
VCC PROTECTOR
NJM8068G
Q104
4K7
R379
IC120
D115
KTC2875B AGND GND1
47K(SUSUMU)
Q117
KRC102S GND2
R384
R385
56K
47K-SUSUMU
VSS
R386 AMPIN_GND
Q106 33K Q118
C279
4 3 2 1
R388
KRC102S KRC102S VOL_L AMPIN_L
47K-SUSUMU
R396
-
AUDIO_MUTE
C283 Q105
TU_R' AGND
-
- AMPIN_GND
R375
KTC2875B
AGND VOL_R AMPIN_R
C281
100N-K R393 AMPIN_GND
TU_L' J102
470(AX)-AMRS
C285 C282
12K
C286
HP_L HP_L
AUX_L'
35MU104KZ22012 35MU104KZ22012 47/50(6.3*11)-RFO H/P_GND H/P_GND
AGND HP_R HP_R
CN104 AUX_R'
R399 1K5 160923 ADD
CN104
TO CP703
SM125Z-19T
VOL_R1
VOL_L1
LBAS16HT1G
OPT1 OPT1
KTC3203Y
D116
DGND DGND
Q107
Repair Information
R401
OPT2 OPT2
R402
3K9
12
R403
R406 R400
DGND DGND
12
R404 R405 27K
0
R418
NET00445 HP_L
CNT1 PART
D3V3
33 33 C289
0
Q108
47K
C288
R408
SW_MUTE SW_MUTE' H/P_GND KTC2875B 10/50-Z8156 C290
100/25(6.3*11)-RFO
12
R411
10/50-Z8156
100P-J
PROT_V PROT_V HP_R
D117 12
Q110 R407
LBAS16HT1G
1K R409
160919
PWR_ON PWR_ON KTC2875B
KTA1271Y
R410
R413
100-SUSUMU
10K
Q109
C291
PWR_DN PWR_DN 100N-K
R412 8 7 6 5
C325
DGND DGND 33K R414 VCC
NJM8068G
DAB_SPDIF DAB_SPDIF'
H/P_GND
IC122
1K5
DGND DGND
R415
DAB_DA/TU_SDA DAB_DA/TU_SDA R457 R458 VSS
1K5
LBAS16HT1G
100P-J
DAB_CLK/TU_CLK DAB_CLK/TU_CLK 10K 10K 1 2 3 4 C292
R416 100N-K
160919
TU_INT TU_INT 33K
C353
C354
1000N
1000N
D118
47K
KTC3203Y
TU_RST TU_RST R419
Q111
Q112
C326
R463 R464 1K
R421
R420
TU_SEN KTC2875B
10K
R422
TU_SEN
12
R424 C293
12
DAB_TU_ON 5K1 47K 47K 10/50-Z8156 R423
R417
DAB_TU_ON C296 Q113
R425 KTC2875B R426 100-SUSUMU
MUTE_B+ 10/50-Z8156
100N-K
MUTE_B+ R428
CPU PART
C297
C329
R432
SW_OUT 68N 33 33 R427
KTA1271Y R430
C294 27K C295
12
12
TO CN106
100 R429 10/50-Z8156
SW_MUTE'
100/25(6.3*11)-RFO
LBAS16HT1G
C298 10K
REGION OPTION 100N-K
D119
3K9
R431
Q114
8 7 6 5
VSS
5
E2/E3/E1C/JP EK
NJM8068G
VCC
-
3
R459
R437
CN113
R433
R434
1K5
0
470K
VSS Q116
CN114
CN113
7
C330
R460
KRA103S
20010WS-08
1 2 3 4 100N-K
A9
0
VCC
CNT2 PART
C301 C300
8
AUDIO_MUTE
CN114 AGND AGND R438 IC121
20010WS-05 10K NJM8068G
TU_L TU_L' H/P_MUTE'
SW_GND
AUX_L AUX_L' MAIN_MUTE
AGND AGND MUTE_B+
C303
AUX_R AUX_R' 10/50-Z8156 R440
R439 0
VOL_L1'
SW_GND SW_GND 3K9
SW_OUT SW_OUT
R441 R442
VOL_R1' 5A
3K9
C304
10/50-Z8156
0
SW_MUTE' TO A5
TO CP506 TO CP505
Updating
J115 0 J113 10N J111 0 C166 10N-K
AGND
J116 0 J114 1N J112 0 C167 1N
REWORK WIRE
AGND
AGND
AGND
DGND
H/P_GND
DGND
H/P_GND
SW_GND
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
12
SCH04_CNT1
Caution in
servicing
Electrical
CNT1 PART
CN107
CN106 CN106
SF125Z-19T
CN107
SF125Z-19T
INPUT PART
PWR_ON PWR_ON PWR_ON PWR_ON
PWR_DN PWR_DN PWR_DN PWR_DN
Mechanical
DGND DGND DGND DGND
DAB_SPDIF DAB_SPDIF' DAB_SPDIF' DAB_SPDIF
DGND DGND DGND DGND
DAB_DA/TU_SDA DAB_DA/TU_SDA DAB_DA/TU_SDA DAB_DA/TU_SDA
DAB_CLK/TU_CLK DAB_CLK/TU_CLK DAB_CLK/TU_CLK DAB_CLK/TU_CLK
TU_INT TU_INT TU_INT TU_INT
TU_RST TU_RST TU_RST TU_RST
TU_SEN TU_SEN TU_SEN TU_SEN
DAB_TU_ON DAB_TU_ON DAB_TU_ON DAB_TU_ON
MUTE_B+ MUTE_B+ MUTE_B+ MUTE_B+
TO CN104 TO CN502
Repair Information
C545 1000P
CH_GND
CH_GND
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
13
SCH05_INPUT
Caution in
servicing
Electrical
INPUT PART
JK502
RCA-107A
R529 R530
SW
470 470 3
SW_OUT SW_OUT'
2
R531 1
10K
100P-J
100K
Q504
KTC2875B CH_GND
R533
10K C524
SW_MUTE 1N-J
C525
R532
Q505
KTC2875B
R435 SW_GND
470K
OPT1
C526 0
C299 OPT1 VOUT
3
SW_GND
10/50-Z8156
GND
2
L503 C527
0 100N-K 3V3
1
Q115
KRA103S NET00445 D3V3'
JK503
JSR2124 25MBPS
Q121 JK504
KRC102S JSR2124 25MBPS
Mechanical
C528
OPT2
OPT2 VOUT
3
0
GND
2
C529
10/16-Z8154 3V3
1
C530
100N-K
C533
10N-K
BKT510
C539 -
DGND SW_GND
C540 - C534
DGND
DGND
SW_MUTE'
MUTE_B+
A_-12V
100P-J
CH_GND
CN502
SM125Z-19T
CN502
OPT1 OPT1
CN503
DGND
CN503 OPT2 OPT2
SF125Z-17T
DGND
SW_GND SW_GND NET00445 D3V3
SW_OUT SW_OUT SW_MUTE' SW_MUTE
CNT2 PART
PROT_V PROT_V
CNT1 PART
PROT_V PROT_V
PWR_ON PWR_ON PWR_ON PWR_ON
PWR_DN PWR_DN PWR_DN PWR_DN
DGND DGND DGND DGND
DAB_SPDIF DAB_SPDIF' DAB_SPDIF' DAB_SPDIF
CH_GND
DGND DGND DGND DGND
Repair Information
DAB_DA/TU_SDA DAB_DA/TU_SDA DAB_DA/TU_SDA DAB_DA/TU_SDA
BKT511
DAB_CLK/TU_CLK DAB_CLK/TU_CLK DAB_CLK/TU_CLK DAB_CLK/TU_CLK
TU_INT TU_INT TU_INT TU_INT
TU_RST TU_RST TU_RST TU_RST
TU_SEN TU_SEN TU_SEN TU_SEN
DAB_TU_ON DAB_TU_ON DAB_TU_ON DAB_TU_ON
MUTE_B+
TO CN107
A_-12V A_-12V MUTE_B+
MUTE_B+
NC
MUTE_B+ IC506 ISP278R12
REGULATOR 1 B'D
CN515
AD360AF
D516
TO CN506
10N-K
CN515
C549
R554
10K
4P_WIRE
R574
10K
DGND
VIN
DGND
TO CP504
DGND
VOUT(A_+12V)
CN401
IC401
REGULATOR
CN401
2 B'D
LM7805(TO-220F) D401 D402 5P_WIRE
0-3216 0-3216
VIN
DGND
TO _CP505
s
100N-K
100N-K
C401
C402
DGND
DGND DGND
VOUT(+5V)
CH_GND
BKT401
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
14
SCH06_CNT2
Caution in
servicing
Electrical
CNT2 PART CN504
CN504
SM125Z-9T
ST-BY PART
DGND
R534 - 161130
DGND ST_BY DGND/AMP_GND
R535 - Connection option
DGND
A_+12V
161130
R534, R535 A_-12V
0ohm->OPEN IC402 +3V9_ST
LM7805RTR
PWR_DN
TO CN511
100/25(RFO, 6.3*11)
100N
PWR_ON
1U-K-25V
PROT_V
C403
C568
CN505
C404
CN505
SM125Z-05T
DAB PART
DAB_CLK/TU_CLK
5
DAB_DA/TU_SDA
4
TU/DAB_5V TU/DAB_5V
3
DGND
2
DAB_CLK/TU_CLK
DAB_SPDIF
DAB_DA/TU_SDA
1
RESION OPTION
TO CN110
DAB_SPDIF'
-
-
EK E2, E3, E1C, JP
PWR_ON
PWR_DN
+3V9_ST
PROT_V
A_+12V
R536 OPEN 33
A_-12V
Mechanical
DGND
R537 OPEN 33
R538 OPEN 33
R544
R545
R539
R540
OPEN
OPEN
33
33
CN506
R541 OPEN 0 CN506
DGND
R543 OPEN 0 SM125Z-17T
C554 OPEN 100N
TUNER OPTION C555 OPEN 100N SW_GND SW_GND
TU/DAB_5V
TM501 C561 OPEN 1000P
K/SP(JP) E903-99021-001-0S C562 OPEN 1000P SW_OUT SW_OUT
E2(EU) E900-99030-001-0S C531 OPEN 22/50
PROT_V PROT_V
E1C(CH) E900-99080-001-0S C532 OPEN 22/50
E3(NA) E903-99092-001-0S C553 OPEN 470/10 PWR_ON PWR_ON
TM501 OPEN TUNER
PWR_DN PWR_DN
INPUT PART
CN505 BTOB 5P OPEN
CP505 OPEN 8P WIRE DGND
CP506 5P WIRE OPEN
DAB_SPDIF' DAB_SPDIF
DGND DGND
TM501 DAB_DA/TU_SDA DAB_DA/TU_SDA
TUENR(WINEVER)
DAB_CLK/TU_CLK DAB_CLK/TU_CLK
TUNER PACK
R536 33
TU_INT TU_INT TU_INT TU_INT
(WINEVER)
R537 33
TU_RST TU_RST TU_RST TU_RST
7
R538 33
TU_SEN TU_SEN TU_SEN TU_SEN
6
R539 33
TU_SDA DAB_DA/TU_SDA DAB_DA/TU_SDA DAB_TU_ON DAB_TU_ON
5
R540 33
TU_SCLK DAB_CLK/TU_CLK DAB_CLK/TU_CLK A_-12V A_-12V 160928
4
4 5 6
3 2 1
3
R542
TO CN503
100N-K
R541 0
R_OUT TU_R NC
2
R543 0 0
L_OUT TU_L
1
1U-K-25V
100N-K
100N-K
22/50
22/50
C552
470/10(6.3*11)
IC501
TPS22918
C550
C551
C553
1N-J
CP505
C554
C555
C532
C531
C561
Repair Information
1N-J
CH_GND
CP505
8P_SHIELD_WIRE
C563
1N-J
C562
MUTE_B+
1N-J TU_R TU_R'
CP506
-
CP506 AGND
5P_SHIELD_WIRE
TU_L TU_L'
TO CN114
R550
R551
AUX_L AUX_L'
SPK PART
0
SW_OUT SW_OUT
MUTE_B+
5 TO CN113 A_+12V
C560
1N-J
DGND 161130
R546 C556 ST_BY DGND/AMP_GND
JK505
2P_RCA
AUX_L' DGND
22/50 Connection option
1 470
180P-J
R547
100K
AUX IN
C557
DGND
3 DGND
AGND
DGND
TO CN513
180P-J
2
R548
100K
C558
4 R549 C559
AUX_R' C564 1000P
22/50
470
C565 10N
C566 1000P
C567 10N
AGND
DGND
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
15
SCH07_DAB
Caution in
servicing
Electrical
DAB PART
CN111
32P_PIN_SOCKET
NC
32
NC
31
GND_D
30
GND_A
29
DAB_nRST
28
R443 0
USB_DET
27
USB_DN
26
USB_DP
25
R444 47
DAB_SPDIF DAB_SPDIF
24
GND_D
23
NC
22
160919
GVM130S01
(GLOVANE)
NC
21
NC
20
GND_D
19
Mechanical
NC
18
NC
17
DAB_SCLK DAB_SCLK
16
DAB_SDA DAB_DATA
15
NC
14
GND_D
DAB_SPDIF'
13
DGND
NC
CN110
12
NC
CNT2 PART
11
NC CN110
10
SF125Z-05T
NC
9
R445 0
NC DAB_SCLK DAB_CLK/TU_CLK DAB_CLK/TU_CLK
5
R446 0
NC DAB_DATA DAB_DA/TU_SDA DAB_DA/TU_SDA
7
4
R447 10K
FIX LOW TU/DAB_5V TU/DAB_5V
6
3
FIX LOW R448 10K D120 DGND
5
2
LBAS16HT1G
GND_D D121 LBAS16HT1G L124 IC125 DAB_SPDIF
4
1
BLM18PG221SN1 LM1117-3.3
GND_D
3
IC126 TU/DAB_5V
L125 L126 161130
+3.3V BLM18PG221SN1 LM1117-1.2
2
TO CN505
100/10
100N-K
10N-K
10N-K
10N-K
10N-K
10N-K
10N-K
LBAS16HT1G
100/6.3-Z8156
22P-J
22P-J
47/6.3-Z8155
47/6.3-Z8155
0
D122
C306
C309
C308
C312
C313
C307
C311
C314
C317
R449
R450
C315
C316
C318
C319
DGND
C324
C310
C305
100/6.3-Z8156
220/6.3-Z8157
100/6.3-Z8156
Repair Information
For LPP
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
16
SCH08_FRONT
Caution in
servicing
FRONT PART
Electrical
SDB TONE TUNED AUTO STMONO TOTAL RANDOM 1 FLD ALL SLEEP
PGND
LGND
/RST
OSC
VDD
TSB
TSA
DA
CP
CS
VH
F2
1 4 5 6 7 8 9 10 11 12 13 14 30 31 32 33 34 35 36 37 38 39 40 43
CN501
POWER PART
R501 1.0 FL1
1
R502 1.0 FL2
2
R503 +VKK
3
C501 100P R504 10
C502 100P 10
100NF
RC501 3P WAFER
10NF
CN501
10NF
50V/1UF
C504 100P
C503
TO CP502
C506
C507
C508 100NF
Mechanical
16V/100UF
C505
R505 10
C509
C511
C512
47P
C510 100NF
10N
R506
47K
C513 OPEN
FPC502
33
33
33
33
+3V3_ST
R507
R508
R509
R510
DGND
160923
DGND
VFD_3V3
VFD_RST
CPU_PART
VFD_CE
VFD_CLK
VFD_DA
RMC
LBAS16HT1G
LBAS16HT1G
KEY1
D501
LBAS16HT1G
LBAS16HT1G
LBAS16HT1G
LBAS16HT1G
KEY2
D503
D504
D505
D506
D502
EX_INTERRUPT
R511 0
VOL_UP
R513 R514 R515 R516 R517 R518 R519 R512 0
VOL_DOWN
1.8K 1.5K 1K 0 1.8K 1.5K 1K H/P_DET
OPEN/CLOSE
PLAY/PAUSE
STOP/BAND
ON/STANBY
RED_LED
SOUCE
(0.66V)
S501
S502
S503
S504
S505
S506
S507
S508
(0.99V)
(0.66V)
10NF
(0.3V)
+SKIP
(0.99V)
-SKIP
C515
(0.3V)
10NF
C514
R520
(0V)
22K
(0V)
BT
Q502 GREEN_LED
FPC502
KRA102S FPC 17P
JK501
TO FPC101
VR501
H/P JACK
Repair Information
Q501
L501 BD121 KRA102S
4700P
4700P
KRC102S
R522
R521
680
120
D507
C516
C517
10N(FILM)
10N(FILM)
C518
C519
R523
0-1608
LBAS16HT1G
10K
D508
10K
10N
10N
R524
LBAS16HT1G D509
BD121
C520
C521
R526
R G
R525
C523 C525
1000P 1000P
C524 C526
- 10N
CP501
-
CP501
3 2 1 H/P_WIRE
R527
R528
HP_L
HP_R
H/P_GND
GND503
TO CP705
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
17
SCH09_SPK
Caution in
servicing
Electrical
SPK Part
SPK L
JK506
2
C581
L-CH
NM
1
_CP504
100NF/100V
NM
GND1
C582
1000P
C596
GND1 3
C598
MAIN MUTE Q516
KRC102S
HI+B
C583
R-CH
HI+B NM 3
LBAS16HT1G
AMP_GND
100NF/100V
AMP PART
AMP_GND
NM
D551
1000P
C597
HI_B-
C584
RL502 1
C599
HI_B-
2
AMPOUT_L L510
Mechanical
AMPOUT_L
L508 JK507 SPK R
AMPOUT_R
R581 C585 C586 CN512
AMPOUT_R 33K(AMRS) R582 NM 4700/35V(UTSP)
NM C587
100NF/250V
160919 NM AC
3
D552
C588
2.5mm 13P CNT R583 R584 C589 C590 GND
2
CP504 33K(AMRS) NM NM 4700/35V(UTSP)
C591 AC
1
L509
TO CP706
NM
L511
R585 R586
1K2(1) 1K2(1)
DZ502
LBAS16HT1G DZ503
CN513 CN513
BTOB 7P
C592
10/50(ELNA)
ZJ3.9B
J501 NM
J502 NM
MUTE_B+ R587 NM J503 NM
A_+12V R588 NM
GND C593
H_GND CONNECTION 10NF
GND 1 2 3 1 2 3
NC GND504 GND505 BKT510
C594
NC 100NF BKT-BURRING
160928
NC
CNT2 PART
TO CN507
Repair Information
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
18
SCH10_AMP
Caution in
servicing
RCD-M41 AMP ASSY
100N-K
R702
100K
FL
470 C703 C701
R704 R706 100N-K
220/25(NICHICON) 470 470
2N5551S
R705 C704
R703
Q701
C702
10K 100N-K
Q702
2N5401S
P701 Q705 Q706
2N5401S 2N5401S
Q707
22K
100/16
22K
10K
Q703 Q704 DHPTF1608471P85T
0
2N5401S
680K
2N5401S 2N5401S
10N-K
22K
2N5551S
R707
R708
10N-K R709
R712 Q710
C705
R710
Q708 R714 2SD2081
Q709
22K 2N5401S 47
C752
R711
R713
100
100
C706
100P R717
Electrical
C707 - 10K
C751
C709 2 Q711
R720
R715
R716
100/25(TOSHIN) 1K5 R721 33K C708 R718 2N5551S
R722 R719 - 6K8
4K7 0R33(3)
3 1
Q712 L701 1uH
4 5
470/16(ELNA)
HN4A06J
1K(B)-V
C710 - Q713 R724 10
C711 R723
- KTC3964 0R33(3)
10(1W) 47N-K(FILM)
C717 1000pF(FILM)
R728 C713 - R725
C. W.
C712
33K
1K5 240
C715
-
R726 2N2-K(FILM)
VR701
C714
NM
0
82K
R727
C716
R729
47K
33K
Q714
R732
R734 2N5551S R735 47 Q715
Q716
R730
R731
Q717 1K2 2SB1259
1K2
R733
2N5551S 2N5551S Q720
Q718
2N5551S
R797
R799
NM KTC3875
NM
C718
LBAS16HT1G
R738 R739
R736 R737 470/16(RFO) R807
Q719
220-1608
470 470 220-1608
KTC3875
10K
11K
R808
D702
47/50(RFO)
R741 - C748
NM
NM
470 C747
R798
R800
C720 220P(FILM)
R742
R743
-
C721
C745 100P
Mechanical
C756 -
C757 -
R746 R747
- - R748 100
R749 4.7R
CP703 Q721
2N5401S
R750 10K
MAIN MUTE CH.L IDDLE+
R751 10K
PROTECTOR CH.L IDDLE-
GND1
GND1 R754 10K
CH.R IDDLE+
AMPIN_GND R755 10K
CH.R IDDLE-
AMPIN_L
AMPIN_GND
AMPIN_R
AMPIN_GND
HP_L CP706
H/P_GND
HP_R GND1
R757 GND1
FR
160923 ADD R760 R761 C719
TO CP102
470 C725 - - C724 MAIN MUTE
C753 C754 R759 R763 100N-K 220/50(RFO)
220/25(NICHICON) 470 470 R762 C726 HI+B
Q723
- - 10K 100N-K
2N5401S HI+B
R764 R765
CP705 - -
P702 Q726
2N5401S
AMP_GND
2N5401S Q727
Repair Information
DHPTF1608471P85T AMP_GND
HP_L Q724 Q725 2N5401S
680K
2N5401S HI_B-
H/P_GND C722
22K
220/50(RFO) HI_B-
HP_R R767 Q729
Q728 R769 2SD2081 AMPOUT_L
22K 2N5401S 47
TO CP501
R766
AMPOUT_L
R768
C728 AMPOUT_R
100P R770
C729 - 10K AMPOUT_R
C731 2 Q730
R773
100/25(TOSHIN) 1K5 R774 33K C730 R771 2N5551S
R772
TO _CP504
R775 - 6K8
4K7 0R33(3)
3 1
L702 1uH
4 HN4A06J 5
1K(B)-V
- KTC3964 0R33(3)
2N2-K(FILM)
10(1W) 47N-K(FILM)
C739 1000pF(FILM)
C734
33K
1K5
C737
240
-
R779
VR702
C736
NM
0
R780
C738
R782
82K
Q733
33K
47K
2N5551S R785
R787 R788 47 Q734
1K2 2SB1259
R783
R784
Q735 Q736 Q737 1K2
R786
2N5551S 2N5551S 2N5551S Q738 Q739
R804
R801
KTC3875 KTC3875
LBAS16HT1G
C740
R789 R790 470/16(RFO) R792 R806
D703
470 470 R805 R791
220-1608 NM NM 220-1608
11K
10K
47/50(RFO) C744
R794 - C750 10/50(RFO)
NM
NM
470 C749
R803
R802
C742 220P(FILM)
R795
R796
-
C743
C741
C746 100P 10/50(RFO)
Updating
BKT109 BKT105 BKT106 BKT107 BKT108
BKT104 BURRING
BURRING BURRING BURRING BURRING
BURRING
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
19
SCH11_ST_BY
Caution in
servicing
g Note: For products with a serial number in the following
table, see the schematic diagram in SCH12_ST_BY-2.
ST-BY PART
Model Applied Serial Number
DM41 SBKE3 02014-
Electrical
IC502
0
LM7808(TO-220F)
D510
RCDM41 SP 05412-
TO CNT1_GND 1SR156-400
C596
C597
CN512
1SR156-400
D511
DC_5V
100N-K
C544 100N-K
RCDM41 DABBKEK 17171-
CPU PART
CP504
DGND
47/50(RFO)
C543 -
A_-12V
TO CN515
DGND
DGND
+14.2V
C541
+12V
C542
A_+12V
MOT_GND
+8VM
R552 CP504 RCDM41 DABSPEK 19870-
2200/25(UTSP)
4K7
+3V3_ST
DGND Q506
RCDM41 SPE2 03902-
C546
D512 KRC102S R553 D513
C550
DGND LBAS16HT1G 22K LBAS16HT1G
TO CP101
220/16V(UTSP)
CN512 D514 D515
10N-K
47N-K
R555
C547
C548
8K2
9P WAFER(2.5mm)
10N-K
R556
100K
C549
1N4007 1N4007
J557 JUMPER R557
D517 1K
R558
R559
200K
100K
220/16V(UTSP)
10K
10N-K
R561
LBAS16HT1G
CN509
C551
10N-K
4K7 D518 D519
D520
10N-K
AC15V
C555
8
C552
C553
R560
LM7912(TO-220) C554 1N4007 1N4007
Q507
_CP505 +14.2V
7
D521 KRC102S IC504 2200/25(UTSP)
TRANS
LBAS16HT1G R562 D522 DGND
6
22K LBAS16HT1G -14.2V
5
CP505 D524 1N4007
DGND
DGND
DGND
+8.5V
+8.5V
+5V
4
L508 BD221 D523 1N4007
2200/25(UTSP)
+8.5V
3
R563 56(1/4)
10N-K
10N-K
C556 AC3.5V
47/50(RFO)
C558
C557
C559
2
R564 100/50(RFO) R565 56(1/4)
15K
TO CN401 AC3.5V
1
C581
Q508
D525 KTC1027Y
Mechanical
LBAS16HT1G 1N4007 R566
D526
47/50(RFO)
10/50(RFO)
1N4007
47/50(RFO)
Q509 330
ZJ5.6B
100/63
100/63
KRC102S
R567 D527 D529
R568
LBAS16HT1G
4K7
CP502
100/50(8*11.5)
ZJ20B
47K LBAS16HT1G
FRONT PART
R570
R569
4K7
C563
C560
C561
C562
3K9
C564
C565
D531
D533
D528
D530
"H" PROTECTION D532 Q510 ZJ20B
KRC102S
LBAS16HT1G R571
FL1
1
4.7/50(5*7)
22K
FL2
C566
2
R572
15K
C576 10N
+VKK
3
C582 10N
C583 10N CP502
LBAS16HT1G
R573
1K
F501
IC505 JZC-36FD/005-HLT AC220_240 : T1.0AL/250V
RL501 AC100_120 : T2.0AL/250V
NJM2845DL1-33 C567 D534
1
LBAS16HT1G
TRANS
3 4
10/50 ZJ6.8B C568 F501 CP503
10U-M-6.3V
47/50(RFO)
4N7
2
D535
J553 JUMPER
D536 D537 D538
1U-K-25V
JUMPER
22/50(RFO)
C572
C570
D540
JUMPER
C569
J549
D542
D548 1N4007
CN511
Repair Information
LBAS16HT1G
AC_CORD
CNT2 PART
CN511
BTOB_9P D545 D546 1N4007 CN510
R590
T501
10K
2200/16V
PROT_V
R576 0 s 1N4007
D547 1N4007
C575
-
C577 10N-K
C574
PWR_ON
Q512 100N(EB)-100V
PWR_DN JUMPER KRC245S
J559
C578
+3V3_ST
s D553 1N4007
R589
10K
A_-12V
A_+12V
R581 51K R579
AMP_GND CONNECTION GND J510 JUMPER J505 0
Q513, R589, D550 Q514 4K7 J511 JUMPER J506 0
GND
C579 10N-K
10K
D550
47K
J516 JUMPER
J508 JUMPER
R580
TO CN504
J512 JUMPER
-
KRC102S
J556 JUMPER
J515 JUMPER
1N-J
-
-
J560 JUMPER
R578
J552 0
J561 JUMPER
J558 0
C573
C580
C595
J514 JUMPER
J513 0
BKT502 BKT501
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
20
g
SCH12_ST_BY-2
Caution in
servicing
ST-BY PART Note: This schematic diagram is for products with a se-
rial number in the following table. For products with
earlier serial numbers, see SCH11_ST_BY.
161207
Electrical
IC502
0
LM7808(TO-220F)
D510
TO CNT1_GND 1SR156-400
C596
C597
1SR156-400
Model Applied Serial Number
D511
DC_5V
100N-K
C544
CPU PART
DGND
47/50(RFO)
- 100N-K
A_-12V C543
DGND
DGND
+14.2V
C541
+12V
C542
A_+12V TO MAIN_CH
12V REGULATOR
MOT_GND
RCDM41 SP 05412-
1SS355 171115
TOSHIN KOGYO
R552
+8VM D541
2200/25(UTSP)
4K7 160922
CP504
+3V3_ST
D&M 160919
DGND Q506 TOSHIN KOGYO
C546
KRC102S R553 D513
D&M
D512
C550
DGND LBAS16HT1G 22K LBAS16HT1G
220/16V(UTSP)
D514 D515
C584 10N-K
CN512
10N-K
47N-K
10K
1SS355
R555
C547
C548
SIZE_¥õ10
8K2
171115
D539
171115
9P WAFER(2.5mm)
10N-K
RCDM41 DABSPEK 19870-
R556
100K
C549
161011 1N4007 1N4007
R574
J557 JUMPER R557
D517 1K
J555 JUMPER
LBAS16HT1G
R558
R559
LM7912(TO-220)
200K
100K
220/16V(UTSP)
10K
R561 160922
10N-K
LBAS16HT1G
CN509
SIZE_¥õ10
C551
161011 D518 D519
10N-K
4K7
D520
IC504
10N-K
AC15V
C555
8
C552
C553
R560
C554 1N4007 1N4007
7
D521 KRC102S 2200/25(UTSP)
TRANS
LBAS16HT1G R562 D522 DGND
6
1SS355 D543 D&M
22K LBAS16HT1G TOSHIN KOGYO -14.2V
5
CP505 171115 D524 1N4007
DGND
DGND
DGND
+8.5V
RCDM41 BKE1C 01184-
+8.5V
+5V
4
L508 BD221 D523 1N4007
2200/25(UTSP)
+8.5V
3
R563 56(1/4)
10N-K
10N-K
C556 AC3.5V
47/50(RFO)
C558
C557
C559
2
R564 100/50(RFO) R565 56(1/4)
15K TO AMP_Heatsink AC3.5V
1
5V REGULATOR
C581
Q508
D525 KTC1027Y
Mechanical
170130 D&M 1N4007
D526 LBAS16HT1G R566
47/50(RFO)
10/50(RFO)
1N4007
47/50(RFO)
Q509 330
ZJ5.6B
100/63
100/63
KRC102S
D527
R568160922 R567 D529
LBAS16HT1G
4K7
100/50(8*11.5)
ZJ20B
47K LBAS16HT1G
FRONT PART
R570
R569
4K7
C563
160922
C560
C561
C562
3K9
C564
C565
D531
D533
D528
D530
"H" PROTECTION D532 Q510 ZJ20B
KRC102S
LBAS16HT1G R571
FL1
1
4.7/50(5*7)
22K
FL2
C566
2
R572
15K
C576 10N
+VKK
3
C582 10N
C583 10N CP502
170120 EMI
Q511 KTC1027Y
LBAS16HT1G
R573
1K
IC505 JZC-36FD/005-HLT
RL501
NJM2845DL1-33 C567 D534
1
LBAS16HT1G
TRANS
3 4
10/50 ZJ6.8B C568 F501 CP503
10U-M-6.3V
47/50(RFO)
4N7
2
F501
D535
AC220_240 : T1.0AL/250V
J553 JUMPER AC100_120 : T2.0AL/250V
D536 D537 D538
1U-K-25V
JUMPER
22/50(RFO)
C572
C570
D540
J549 JUMPER
C569
D542
D548 1N4007
LBAS16HT1G
Repair Information
AC_CORD
CNT2 PART
CN511
BTOB_9P D545 160919 D546 1N4007 CN510
R590
T501
10K
2200/16V
SIZE_¥õ10
PROT_V 160315 1N4007 C575
R576 0 D547 1N4007 C574 -
C577 10N-K
PWR_ON OPEN
Q512 100N(EB)-100V
PWR_DN JUMPER KRC245S
J559
C578
10K
A_-12V
A_+12V
R581 30K R579
AMP_GND CONNECTION GND J510 JUMPER J505 0
Q513, R589, D550 Q514 4K7 J511 JUMPER J506 0
GND
C579 10N-K
KRC102S
J509 JUMPER J507 JUMPER
GND
l
EK,E2 E3,E1C,JP
R577
D550
47K
J516 JUMPER
R581 30K 47K J508 JUMPER
R580
KRC102S
J556 JUMPER
J515 JUMPER
1N-J
170120
-
-
161001 J552 0
(POWER DOWN MODIFY) J561 JUMPER
J558 0
C573
C580
C595
J514 JUMPER
J513 0
BKT502 BKT501
Updating
GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO STBY POWER
21
PRINTED CIRCUIT BOARDS
MAIN, INPUT, CNT 1, CNT 2, REGULATOR 1, REGULATOR 2, DAB EK Only, GUIDE R, GUIDE F, SUB GUIDE F , GUIDE
Lead-free Solder
Caution in
servicing
When soldering, use the Lead-free Solder (Sn-Ag-Cu).
MAIN (A SIDE) MAIN (B SIDE) INPUT (A SIDE) INPUT (B SIDE) DAB (A SIDE) DAB (B SIDE)
EK Only EK Only
C349 J115 J113 R419 R407
C350 J111 R417 R410
J116 CN113(RD) CN114(RD) J112 J114
CN503
C345 CP102
CN104
CN101
CLOSE S/W
LIMIT S/W
OPEN S/W
SP+
SP-
SL+
SL-
DGND
LIMIT S/W
R433 Q108 C162
DGND
Q113
R211
R212
LOAD+
LOAD-
CN111
DGND
C333
R210
SP+
C325
R404
R405
SL+
SP-
R426
R425
C326
SL-
DAB_CLK/TU_CLK
NC
CN102
MUTE_B+
-12V
DAB_TU_ON
TU_SEN
TU_RST
TU_INT
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
DGND
DAB_SPDIF
DGND
PWR_DN
PWR_ON
PROT_V
SW_OUT
SW_GND
DAB_DA/TU_SDA
DAB_TU_ON
CLOSE S/W
DGND
OPEN S/W
LOAD-
LOAD+
CN113 CN114 C300
DAB_SPDIF
C258
R434
MAIN MUTE
PROTECTOR
GND1 R438
GND2
MUTE_B+
PROTECTOR
C296
C332
C331
SW_GND
J151 (8P ETC) (5P EK) Q112 Q110
AMPIN_GND
IC123 AMPIN_GND
AMPIN_GND
C158
TU_SEN
TU_RST
PWR_ON
PWR_DN
MAIN MUTE
SW_OUT
TU_INT
PROT_V
R428
C288 C298
C257
X109
R368 C294
H/P_GND
AMPIN_R
C156
NJM8068G AMPIN_L
DGND
DGND
OPT1
DGND
OPT2
DGND
D3V3
SW_MUTE
PROT_V
PWR_ON
PWR_DN
DGND
DAB_SPDIF
DGND
DAB_DA/TU_SDA
DAB_CLK/TU_CLK
TU_INT
TU_RST
TU_SEN
DAB_TU_ON
MUTE_B+
-12V
TU_R'
AGND
TU_L'
AUX_L'
AGND
AUX_R'
SW_GND
SW_OUT
AMPIN_GND
AMPIN_L
AMPIN_GND
AMPIN_R
AMPIN_GND
HP_L
H/P_GND
HP_R
SW_GND
SW_OUT
C251
C253
NC
C314 C315 L125
R362
C301
GND2
GND1
C233
AUX_R'
HP_R
JK502
AUX_L'
R421 R401
HP_L
R365
C252 C317
AGND
AGND
R430
TU_R'
R444
C256
TU_L'
R408
C524
R449
R450
R443
RCDM41 DAB
R196 C244 C254
C316
R533
R364 R370
R531
38
MAIN
C230 R367
RCDM41_INPUT
C2
R198
R445
R446
L120
R361
STEP : MP
R453 C163 IC126
R197
R195
Q114
Q111
Q107
Q109
R452 R356 C164
C243
C234 C277 LM1117-1.2
[[ G ]]
R369
STEP : MP
R451 C175
C308
R353 R456
Pb
7020-08141-040-0V
Q105
Q116
C232 R199
C7
R447
C297
R429
C299
R448
R415
R351 C221 R399 R207
C309
SW_MUTE
R338
C134
Q104
DAB_SPDIF
DAB_SPDIF
7020-08141-040-0V
R346 R340
PWR_ON
R345
PWR_DN
R414
PROT_V
DAB_CLK/TU_CLK
R204
C203
DGND
DAB_DA/TU_SDA
R342
R439
DGND
DGND
DGND
R441
C157
R383 R388
D121
OPT2
OPT1
C293
R436
C302 L121 TU/DAB_5V
D3V3
RCDM41
R339 7020-08141-040-0V
D116
D117 R411
7020-08141-040-0V
C248 R363 C278 C279 R203 Q504 Q505 DAB_DA/TU_SDA
J125
DAB_TU_ON
R201 STEP : MP RCDM41_DAB
C340
R386
R334
R335
DAB_CLK/TU_CLK
C303
C133
MUTE_B+
Q103
C240
L108
IC105
L107
TU_SEN
R208 R205
R463
C353
TU_RST
C275
TU_INT
R378 AM5888S C292 DAB_SPDIF
C324
DGND
C304
D119
D118
C166 R380 C204
R331
R206
C153 IC122 C319
C160 C159
C310
7020-08141-040-0V
C211
R432
C167 DGND
R422
TP112
TP113
TP114
7020-08141-040-0V
R529 R530
R403
R532
C525
NJM8068G
R326
R325
C246 IC115
R379 TU/DAB_5V
C143 C161
C227
R413
R330 R459
STEP : MP
IC127
J1
C280 C283 R420
D122
DAB_DA/TU_SDA L124
X103 16M9344
R209
R402 R406
R329
38
Q115 C311
C540
PCM9211 R423
C312
C539
DAB_CLK/TU_CLK
R431 R427
R328 R348 R418 C295 C140
NJW1194A
IC125
C229
R327 C139 Q117
Q121
CN110
LM1117-3.3
R215
R457
R400 J124
C330
C145
C305
R440 R442
R354 J128 R202
C307
C306
J101
C141 C526
R352 IC124 C247 C142 TP110 TP111 R200 Q118
IC104
BU9546KV
PCM5100A C144
C210
NJM8068G
C127 R182
C354
R458
C347
9
R350
C274
R374 C291
8 10
R347 R376 C290 C138 R189
J131
C313
C165
10 TP
C216
R358
R341 R409
IC121
R190
J1
C226
R344
R343
C237
C236
C235
R336 R396 C169
L105
D120
RCDM41_INPUT
3
D115
STEP : MP
3
C239
C245
C346 R193
TP
R191
R192 R460 C527
C270 C273 TP106
C220
TP107
TP101
C209
C339
R213
R214
R382
3
R355
R359
R360
R464
C329
10
C215 TP105
R381
FPC102
TP
R332
TP104
C289 JK503
C348
C125 C132
Electrical
C228
R290
R293
R297
TP J1
R181
[[ G ]]
C219
10 22 IC109
C286
C129
Pb
R371
2 W9812G6KH
C212 C131
TP115
TP116
C7
VC
C214
Q106
C205 R461
C128
R384
C1 13 35
C213
R385
Q101
VCC
C 1
C528
37 6 L106
RLY101 HFD27/012-S C124
NJM8068G
C
E
SW_MUTE
R194
DAB_CLK/TU_CLK
C530
R275 R277
R274 R273
R269 R271
R263 R267
PWR_ON
J121
D
PWR_DN
DAB_DA/TU_SDA
PROT_V
C123
R291
C344
A
R186
R185
R184
R183
DGND
DGND
IN ICT OP ADJ FI
R462
C122
IC120
OPT1
OPT2
D3V3
R278
B
R245
5
DAB_TU_ON
J139
C529
7
DAB_SPDIF
C
R3
R241
R252
R393
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
J119
MUTE_B+
F C130
C343
TU_SEN
C342
C281
TU_RST
D109
TU_INT
R187
R244
AGND1
DGND
DGND
C154
C196
DAB_TU_ON
DAB_SPDIF
SW_MUTE
LD
R248
R247
J148
J147
J146
C285 C282
C250
R256
R262
R265
R268
R270
R276
R272
R284
6
C155
VR
MUTE_B+
TU_SEN
TU_RST
TU_INT
PWR_DN
PWR_ON
PROT_V
D3V3
DGND
OPT2
DGND
OPT1
3
C3
DGND
DGND
R294
PD
J1
RCDM41 MAIN
J1
3
C150
C149
C148
C147
C146
C351 D104
L503
4
F+
4
JK504
9
C338
J1
7
R246 L114 R280 C121
C249
D110
T- C206
R310
R298
R231
0
R220 R283 R227
2
T+ L116 L104
Q123
J1
4
C185
CN502
J1
C181
F-
L112
7020-08141-040-0V L103
4
R127 R282
C261
D114
J1
R307
IC106 L117 R285
STEP : MP
J132
J123
AP7361 R261 D_5V
C184
L118
Pb
10
FPC101
R221
L1
R317 R312
L115
+3V3_ST
X106 C191 J120
L122
DGND DGND A_-12V
18
C264 DGND 24MHz R255 DGND A_+12V BKT510
J1
CP101 R229 R230 L123 VFD_3V3 R236 R319 R288
R235 R258 VFD_3V3 MOT_GND BURRING
R134 R137
R130 R132
2
MLC3730
VFD_RST
1
5
R149
IC107
R233 +8VM
C152
VFD_RST
4
C3
DGND1 R240
R250
R253
[[ G ]] VFD_CE
J1
D103
5
R128
R123
4
R143
VFD_DA
C7 VFD_CLK
D105
J106 DGND
J1
R151
R147
C263
+8VM R121 KEY1 R289 DGND R308 J134 DGND
C241 C151
FPC105
+3V3_ST TDI RMC J107
R392
C208 KEY2
R125
R301
R295
R299
R292
5
R139
Q122
C3
R216
C207
DGND R165 VOL_UP TDO C182
Q120 KEY2
Q124
L111 DGND
CP101
C268
C107
TCK
C267
LM1117-3.3
H/P_DET LM1117-3.3
IC114
C262 NTRST C199 VOL_UP R153
W9812G6KH
RED_LED TMS C179
IC108
GREEN_LED VOL_DOWN
R105
R109 VDD R311
R389
H/P_DET
D106
C269
IC116 R315 R110 R111 C178 R138
R302
R303
R304
R305
C117
LM7808RTRL R112 R217 C193 RED_LED
R357
R163
R107 R114 R106
R223
R225
R264
L127
C194
C197
C272
IC103 X102 R102 BU4827F R178
C222
LM1117-1.2
J153
C118
D127
D107
R113
CW24C16CDR R173
C195
32.768KHz R166
IC112
R104
J154
R167 R168 L128
C103
R180
C120
R169 R170 R103
R286
R287
C223 J130
C106
R171 R172 IC128 C321 C177
R174
R232 R218 TXD
R228
R226 R219 RTS
R224
R222
C110
C_TX
C_RX
DGND
NC
NC
C104
C3
R455
J105
C111
R152
R150
L102 C105
3
D123
D124
C322
R133
J109
C108
R120 R119
J1
J104
J126
J103
X101 C113 FPC104
SDA
SCL
DGND
RXD
DGND
CTS
RESET
VDD
37
4MHz FPC103
R136
C201
R129 J110
C323
R126 R158
R124 R159
R154 R122
R131
R135
R155
R156
D101 R316
R157 R146 R148
D126
R318
R160
R161
TPS22918
C112
C101
UPDATE_RX
UPDATE_TX
C202
+3V3_ST
C287
RESET
DGND
C327
MO0
C102
C170
C171
C172
C173
C174
C328
NC
CN108
C217
VDD
JTDI
JTDO
JTMS
JTRSTX
DGND
CN112 C218
Mechanical
C284
CNT 1 (A SIDE) CNT 1 (B SIDE) CNT 2 (A SIDE) CNT 2 (B SIDE) REGULATOR 1 (A SIDE) REGULATOR 1 (B SIDE)
CN107
DGND
DGND
D516 VOUT
CN515
VOUT
DGND
DGND
VIN
C125Z2-19-AN
VIN
R540
R539
RCDM41_REGULATOR1
RCDM41_REGULATOR1
Pb
OPT1 7020-08141-040-0V
DGND STEP : MP 7020-08141-040-0V
R554
R543
STEP : MP
R541
DAB_CLK/TU_CLK
C555
DAB_DA/TU_SDA
D3V3 OPT2
R574
ON/OFF
SW_MUTE DGND
ON/OFF
DGND
OUT
IN
[[ G ]]
DGND
PROT_V D3V3 ON/OFF GND OUT IN
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
TU/DAB_5V
DGND
DAB_SPDIF
R538
DAB_SPDIF
OUT
TU/DAB_5V
PWR_ON SW_MUTE
R537
PWR_ON
CN504
PWR_DN
+3V3_ST
C7
C562
PWR_DN PROT_V
PROT_V
IN
R536
A_+12V
C561
A_-12V
DGND PWR_ON
DGND
DGND
DGND
DGND
DAB_SPDIF PWR_DN CN505
DGND DGND C566
DAB_DA/TU_SDA DAB_SPDIF C567
DAB_CLK/TU_CLK DGND
Repair Information
DGND
DGND
DGND
A_+12V
A_-12V
+3V3_ST
PWR_DN
PWR_ON
PROT_V
TU_INT DAB_DA/TU_SDA
C554
R545
R544
TU_RST DAB_CLK/TU_CLK
TU_SEN TU_INT
DAB_TU_ON TU_RST
MUTE_B+ TU_SEN C553
DAB_TU_ON
MUTE_B+
WH
R534
R535
C568
CN506
RCDM41_CNT1
IC402
STEP : MP
LM7805
C563
C403 C404
TPS22918 C560
IC501
C550
C546
C564
C565
RD
SW_GND
SW_OUT
PROT_V
PWR_ON
PWR_DN
DGND
DAB_SPDIF
DGND
DAB_DA/TU_SDA
DAB_CLK/TU_CLK
TU_INT
TU_RST
TU_SEN
DAB_TU_ON
A_-12V
MUTE_B+
NC
DAB_SPDIF
DAB_TU_ON
7020-08141-040-0V
R546
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
CP506 (5P, EK)
CP505 (8P, ETC)
RESET RESET
PWR_ON
SW_GND
PWR_DN
SW_OUT
R547
MUTE_B+
PROT_V
C545 AUX_R AUX_R
TU_SEN
TU_RST
C557 C556
TU_INT
DGND
DGND
A_-12V
AGND AGND
BKT401
HOLE
AUX_L AUX_L IC401
BKT514 LM7805
BURRING OUT G IN
CP506(RD)
TU_L
R550
R551
JK505 TU_L
AGND AGND
TU_R TU_R
RCDM41_REGULATOR2
RCDM41 MAIN
C531 CP505(RD) RCDM41_REGULATOR2 IN G OUT
C559
7020-08141-040-0V 7020-08141-040-0V
Pb
STEP : MP
MUTE_B+
STEP : MP
STEP : MP
R549
R548
C558
DGND
DGND
DGND
DGND
DGND
A_+12V
MUTE_B+
DZ501
A_+12V
RCDM41_CNT1
7020-08141-040-0V
DGND
DGND
DGND
DGND
DGND
D401
STEP : MP
VOUT(+5V)
RCDM41 CNT2
D402
[[ G ]] C401
DGND
DGND
DGND
C7
VIN
BKT515 7020-08141-040-0V
STEP : MP
VOUT(+5V)
DGND
DGND
DGND
VIN
CN514
HOLE
C402
CN507
C548 C532
Pb
C547
C7
[[ G ]]
OPT1 OPT1
DGND DGND
OPT2 OPT2
DGND DGND
D3V3 D3V3
SW_MUTE SW_MUTE
PROT_V PROT_V
PWR_ON PWR_ON
PWR_DN PWR_DN
DGND DGND
DAB_SPDIF DAB_SPDIF
DGND DGND
DAB_DA/TU_SDA DAB_DA/TU_SDA
DAB_CLK/TU_CLK DAB_CLK/TU_CLK
TU_INT TU_INT
TU_RST TU_RST
TU_SEN TU_SEN
DAB_TU_ON DAB_TU_ON
MUTE_B+ MUTE_B+
CN106
C125Z2-19-AN
Updating
GUIDE R (A SIDE) GUIDE F (A SIDE) SUB GUIDE F (A SIDE) GUIDE (A SIDE)
STEP : MP
7020-08141-040-0V
RCDM41_GUIDE
Pb
RCDM41
7020-08141-040-0V
GUIDE F SUB GUIDE F [[ G ]]
7020-08141-040-0V STEP : MP C7
STEP : MP
RCDM41 GUIDE R
22
SPK, FRONT, AMP, ST_BY
Caution in
servicing
SPK (A SIDE) SPK (B SIDE) FRONT (A SIDE) FRONT (B SIDE)
MUTE_B+
657 A_+12V
S503
S507
+SKIP
STOP
675 A_+12V
34 NC
12CN513
CN513
GND
GND
MUTE_B+
GND
GND
NC
NC
CN513
231 NCNC
4 NC
Pb
R518
R515
C7
[[ G ]]
C522
DZ502
GND505
AMP_OUT
C592 R585
J137
FI
R587
R588
C517 D504 D502
4700UF/35V
VR501
JK507
R586 BKT510 D505 D501
ADJ
D506 D503
Bonding
7020-08142-000-0S
7020-08142-000-0S
CN512
C515
R517
S508
S506
C586
PLAY
RCDM41_FRONT(MP)
-SKIP
OP
DZ503 AC R523
C591
R519
RED
CH_GND
ICT
J535 C516
J536
J514
GND
IN
C587
C597
1 HP_L
C584
J139 3 HP_R
Q516
C599
CP501
2 H/P_GND 2 H/P_GND
SOURCE
R524
S501
*3P WRE 260mm
OPEN
R514
3 HP_R
S502
1 HP_L
GND
CN501
RL502 AC C519
AC
CP504
D551
C583
1 +VKK
J538
J559
C518
2 FL2
3 FL1
C588
J564
1 GND1
BK
J543
3 FL1
2 FL2
1 +VKK
1 GND1
L502
L501
2 GND1 2 GND1
AC
Electrical
C589
J544
J513
3 MAIN_MUTE
J545
3 MAIN_MUTE
D552
C509
4 +VCC 4 +VCC
5 +VCC 5 +VCC
JK501
JK506
6 GND
GND
C581
6 GND
C596
7 GND
J542
7 GND
C512 C511
4700UF/35V
8 -VCC
RC501
8 -VCC
D507
D509
C524
C523
Bonding
L509
C585
9 -VCC
L511
BK
9 -VCC R505
CH_GND
C582 10 LCH 10 LCH J533
C590
L510
L508
J515
J516
11 LCH
J560
11 LCH J144
J530
12 RCH
R502
J566
12 RCH
C598
R504
13 RCH
J562
13 RCH C507
J563
AMP_OUT
J561
C503
GND504
C7 Pb
C525
C526
Q503
12 +3V3_ST
C506
RED
[[ G ]]
3 DGND 12 +3V3_ST
R503 R506
FI ADJ OP ICT IN DGND DGND
546 VFD_3V3
VFD_RST 3 VFD_3V3
DGND R520 C510
J503 VFD_CE J527 54 VFD_RST
R584
J529
Mechanical
R512
R511
J528
BKT107 L_CH R_CH E C B B C E E C B E C B B C E E C B
Q715 Q734 Q729
R784 C724
Q713 Q710 Q732
2SB1259 KTC3964 2SD2081
BKT105
R783
KTC3964
R731
R730 C701 C708
R711 Q705 R718
B C E E C B B C E B C E E C B B C E J534
AMPOUT_R J537
BKT106 AMPOUT_R FPC502
R801 AMPOUT_L
Q739 R797 AMPOUT_L J532
R703
C702
J171
HI_B-
R803
Q706 P702 P701
HI_B- J531
R800
Q719
R733
AMP_GND
AMP_GND
Q702 C749 R766
HI+B
R802 HI+B
Q726 MAIN_MUTE
C514
R516
GND1
Q738
J701
R724
CP706
R798
R735 GND1
Q709
J700
R772
0.33(3)
R719
0.33(3)
C747
R785
R714
Q718
R769
Q730
R732
C748
C750
C751
R788
R776
R725
S504
0.33(3)
C712
J192
R709 J147
BT
D703 J190
J185 R778
R710 J191 C726 Q711
R775
J186 C704
R722
J187 J188
C752
J189
J194
R804
D702
J123
R762
R744
R745
J124
Q707
R705
J170
C705
R770
0.33(3)
R723
L701
C730
R771
J103 1UH
R746
R747
Q727 R528
J133
R749
C714
J121
R501
R768
R729
C505
C736
R527
J126
J134
J150
J115
J110
J135
C722
220/50
Q721
J114
J131
J118
AMPOUT_R
J132
J116
J122
J113
AMPOUT_R
R525
C520
FL501
C723
J161
J129
AMPOUT_L J175
J128
J130
C741
J125
AMPOUT_L
R748
R
C744
R
J136
J145
J101
HI_B-
Q501
HI_B- J182
R521
J169
J120
J117
J119
C732
J162
AMP_GND
C729
Pb
AMP_GND
R782
J152
C757
HI+B
ON/STBY
220/50
R765 R760
C719
R767
R795
R763
HI+B
D508
J181
S505
R764 R761
MAIN_MUTE R774 J143
J176 C710 Q502 R522
J159
R526
C521
GND1
R796 C707
R712
GND1
C745
R742
CP705
R721 R757
C746
HP_R
R706
G
R702
J163
Repair Information
H/P_GND Q725 R790
C734
54
Q723
C756 R743
C7
HP_L Q704
J157
J180
J166
J156
J164
J165
J146
Q701
R737
7020-08142-000-0S
C755
53
C742
J179 Q717
C7
R704
J104
C740
Q724
C703
J160
Q728
R759 R781
C743
C725
Q736 R794
Q703
Q708
HP_R J178 C721
R789
L702
C728
C720
1UH
C718 H/P_GND
J155
R736
FI
R728
Q737
J111
C706
J142
Q716
R787
Q731 C733 R808 R807
C737
C738
J193
R726
R734
C715
R780
R779
C735 R805
R806
R773
BKT108 R727
RCDM41_AMP(MP)
R777
R750
C709
[[ G ]]
C7
R792
Q720
R751
R791
J154 C713
J149
R738
OP
J148
J177
HP_R
H/P_GND
HP_L
R754
R739
J141
R716
R755 R708
BKT109
Q733
C731
PROTECTOR
R720
C739
MAIN_MUTE
Q714
AMPIN_GND
AMPIN_GND
AMPIN_GND
VR702 CP702
J174
AMPIN_GND
AMPIN_R
AMPIN_GND
AMPIN_L
AMPIN_GND
GND1
GND1
PROTECTOR
MAIN_MUTE
J138
ICT
C717
AMPIN_R
H/P_GND
AMPIN_L
VR701
R715
R707
CP703
GND1
GND1
CP701
HP_R
J151
HP_L
J158
IN
D530
CN510
C562
8.AC15V
7.+14.2V
6.GND
5.-14.2V
4.+8.5V
3.+8.5V
2.AC3.5V
1.AC3.5V
CN509
CP503
C580
C573
C595
J512
BKT501
C564
R565
R563
AC220_240 : T1.0AL/250V
AC100_120 : T2.0AL/250V
D525
F501B
C582
C565
CAUTION
3.FL1
2.FL2
1.+VKK
CP502
7.+14.2V
8.AC15V
5.-14.2V
C560
CN509
6.GND
C547
ZJ20B R566
C548
D533 ZJ20B
RCDM41 SP 05412-
Q508
RL501 CP502
D514 D527
J510
J511
1.+VKK
CP502
D518
F501
R567
2.FL2
3.FL1
Q509
2200/25
IC502 LM7808
Updating
D523
D524
J515 D510
J514
D515 J516 J551
J556 D511 RCDM41
C542 CN511
7020-08143-000-0S 3.DGNDST_BY C559
2.DGND
Q511
C543 R581
R572 R555 R553
C549
1.+14.2V 7.+3V3_ST
R559
R556
R557
D512 5.MOT_GND
D542
J558
D548
R576
D534 3.DGND 6.+8VM R558
D538
D537
ZJ6.8B CP504
2.DGND 5.MOT_GND 4.A_+12V
3.A_-12V CN512
C574
D553
Pb
R552
C551
D520
J513
C558
4.+12V 4.A_+12V J553
2.DGND
D513
C567 D536
2.DGND 9.NC
D547
J505
D546
C596 IC505
J549
7.DGND 8.DGND
J560
BKT502 D517
CN512
Q513
D521 C597
D550
4.3V3_ST 5.A_-12V
J559
C571
ZJ12B C577
4.3V3_ST
C572
C566 J506
3.PWR_DN 3.PWR_DN L508
2.PWR_ON
2.DGND
3.DGND
4.DGND
J557
R564
C569
1.+8.5V
R561
R562
C581
CLP502
1.PROT_V 2.PWR_ON R589
R590
5.+5V
23
g
ST_BY-2
Caution in
servicing
Note: This printed circuit board is for products with a serial
number in the following table. For products with
earlier serial numbers, see ST_BY.
Electrical
RCDM41 DABSPEK 19870-
RCDM41 SPE2 03902-
RCDM41 BKE2 04091-
RCDM41 BKE1C 01184-
Mechanical
C576
D531
ZJ5.6B
D530
CN510
C562
8.AC15V
7.+14.2V
6.GND
5.-14.2V
4.+8.5V
3.+8.5V
2.AC3.5V
1.AC3.5V
CN509
CP503
C580
C573
J512
C595
BKT501
C564
R565
7020-08143
J561
R563 D525
AC220_240 : T1.0AL/250V
AC100_120 : T2.0AL/250V
F501B
C582 -000-1S
C565
CAUTION
3.FL1
2.FL2
1.+VKK
FOR CONTINUED PROTECTION AGAINST
CP502
C575
C561
A RISK OF FIRE HAZARD, REPLACE ONLY
1.AC3.5V
2.AC3.5V
7.+14.2V
8.AC15V
5.-14.2V
C560
CN509
6.GND
C547
ZJ20B
C548
D533 ZJ20B Q508
CP502 R574
RL501 D514 D527
J510
J511
1.+VKK
C584
CP502
D518
F501
R567
2.FL2
3.FL1
IN GND OUT R570
C563
Q509
C546
F501A
2200/25
IC502 LM7808
D523
D524
J515 D510
J514
D515 J516 J551 RCDM41
D519 J556 D511
C583
C542 CN511 1.+14.2V
7020-08143-000-1S C544 3.DGND ST_BY C559
2.DGND
Q511
R573
T501
RCDM41 ST_BY(MM) R568
D539 (MM) Q512 R577
R580
C579
J552
R571
Q510
C543 9.DGND R560
C549
R569 D543 C557
D542
1.+14.2V 7.+3V3_ST C7 6.+8VM
D528
R559
R556
D512 R557 D541
5.MOT_GND
D548
R576
D534 3.DGND 6.+8VM R558
D538
D537
4.A_+12V
J558
ZJ6.8B CP504
C574 2.DGND 5.MOT_GND CN512
Pb
D553
C551
D520
R552
J513
C558
4.+12V 4.A_+12V 3.A_-12V
Repair Information
J553
2200/25 CN511 2.DGND
D513
OUT IN GND
3.A_-12V CN511
J555
J505
D546
Q507
C596 IC505
BKT502 J549
7.DGND 8.DGND
J560
CN512
Q513
R578
D550
2200/16 C552 J509 5.A_-12V 6.A_+12V
4.3V3_ST 5.A_-12V
R562
J559
- C577
C571
C572
D540
2.DGND
3.DGND
4.DGND
J557
R564
R561
C569
1.+8.5V
C570
CLP502 2.PWR_ON
C581 1.PROT_V R589
5.+5V
1.PROT_V D522
R590
D545 CP505 CLP501
Updating
24
Caution in Electrical Mechanical Repair Information Updating
servicing
RCD-M41 LEVEL DIAGRAM(HEADPHONE)
25
LEVEL DIAGRAM
HEADPHONE
Caution in Electrical Mechanical Repair Information Updating
servicing
RCD-M41 LEVEL DIAGRAM (SPEAKER)
26
SPEAKER
BLOCK DIAGRAM
Caution in
servicing
IC115
NJW1194 Speaker
INPUT SELECT OUT
& VOLUME AMP BLOCK
TU_INT
TU_RST
TU_SEN
TU_SDA
TU_SCLK
Electrical
Headphone
OUT
PCM5100A
IC123 Subwoofer
OUT
IC101
Mechanical
DAB_CLK/TU_CLK
MB9AF344 IC123
DAB_DA/TU_SDA
CD BLOCK
EEPROM_SCL
EEPROM_SDA
IC127
PCM9211
Repair Information
VFD_RST
VFD_CE
VFD_CLK
VFD_DA
RMC
KEY1
KEY2
EX_INTERRUPT
VOL_UP
VOL_DOWN
H/P_DET
RED_LED
GREEN_LED
RESET
RTS
CTS
TXD
RXD
GND
SCL
SDA
KEY ENCODER IR
Updating
FLT
27
POWER DIAGRAM
EEPROM
RCD-M41 CD Receiver POWER BLOCK Diagram CW24C16
Caution in
servicing
u-COM
MB9AF344
32mA BT_MODULE
NJM2845DL1 3V3 MB8811C1
TPS22918
-33
25mA
W25Q16JV
4V1
70mA
AC IN AP7361 W9812G6KH
ADJ
TPS22918
Electrical
LM1117 MLC3730_DS
1V2 +1V2
POWER
TR
+22.8V
S1 LM1117 32mA
PCM5100A
3V3
NM
-22.8V +8V
LM7808
+8V
AM5888S
Mechanical
ISP278R12
+14.2V
+12V 8mA
S2
+12V LM7808 H/P
+8V 8mA
OP-AMP
LM7912 8mA
-12V
-14.2V LM7908 SPK
-12V 17mA 8mA
-8V OP-AMP
17mA NJW1194V 8mA
SW
Repair Information
8mA
OP-AMP
S3 +5V LM7805
+8.5V +5V
LM7805
TPS22918 TUNER
+5V
+3V3 LM1117
LM1117
3V3
3V3 DAB
AC3V5 LM1117
1V2
S4 DAB OPTION
Updating
+42V
S5 BU9540KV
28
WIRING DIAGRAM
RCD-M41 WIRING DIAGRAM
BT
Caution in
EX_INTERRUPT
FRONT PCB
servicing
GREEN_LED
VOL_DOWN
RED_LED
VFD_RST
VFD_CLK
VFD_3V3
+3V3_ST
H/P_DET
VOL_UP
VFD_CE
VFD_DA
DGND
DGND
KEY1
KEY2
RMC
3P WIRE FFC 17P FFC 10P
3P WIRE
3P Wafer
12P WIRE
CD MECHA
H/P_GND
5P WIRE 6P WIRE FFC 16P
PROTECTOR
HP_L
HP_R
MAIN MUTE
AMP_GND
AMP_GND
AMP_GND
H/P_GND
AMPIN_R
HP_L
HP_R
VOL_L
DGND
DGND
Electrical
MAIN PCB
FFC 17P
5P WIRE 6P WIRE FFC 16P VDD
FFC 10P
RESET
RTS
CTS
TXD
GND1 GND
12P WIRE
GND1 RXD
AMP PCB
MAIN MUTE
GND
BTOB 19P
HI+B
SCL
13P WIRE
HI+B
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
AMP_GND SDA
DAB_TU_ON
AMP_GND
DAB_SPDIF
AMP_HEATSINK
SW_MUTE
MUTE_B+
HI_B-
PWR_ON
PWR_DN
PROT_V
TU_SEN
TU_RST
TU_INT
HI_B-
DGND
DGND
DGND
OPT1
OPT2
D3V3
D_5V
AMPOUT_L
WAFER 7P
AMPOUT_L
AMPOUT_R
UPDATE MD0
AMPOUT_R
UPDATE RX
LM7805
UPDATE TX
9P WIRE
+3V3_ST
RESET
Mechanical
DGND
NC
5P or 8P WIRE
ISP278R12
MAIN_CH
ST_BY PCB
BTOB 19P
BTOB 9P
BTOB 9P
PROT_V
PWR_ON
5P WIRE
AC IN
4P WIRE
PWR_DN
+3V9_ST
A_-12V
3P WIRE 9P WIRE
A_+12V FL1 DC_5V
+14.2V
GND GND AGND
FL2
5P or 8P WIRE
GND GND
+VKK A_-12V
GND +12V
TU_R A_+12V
AGND
TU_L MOT_GND
AUX_L +8VM
AGND AC15V +3V3_ST
Repair Information
AUX_R
SW_GND +14.2V DGND
SW_OUT
BTOB 5P GND DGND
2P WIRE
-14.2V
PIN HEADER 32P
+8.5V
TUNER +8.5V
TUNER 8P
TU_INT AC3.5V
TU_RST
DAB PCB
TU_SEN AC3.5V
TU_SDA
TU_SCLK
8P WIRE
TUNER 8P
TU+5V
R_OUT
L_OUT
BTOB 5P
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
TU/DAB_5V
AGND
CNT2 PCB
DAB_SPDIF
SW_GND
SW_OUT
INPUT PCB MAIN TRANS
BTOB 17P
BTOB 19P
BTOB 19P
BTOB 17P
PROT_V
DAB_CLK/TU_CLK
DAB_DA/TU_SDA
PWR_ON
2P WIRE
DAB_TU_ON
PWR_DN
DAB_SPDIF
SW_MUTE
8P WIRE
MUTE_B+
PWR_ON
PWR_DN
PROT_V
TU_SEN
DAB_SPDIF
TU_RST
TU_INT
DGND
DGND
DGND
OPT1
OPT2
D3V3
D_5V
DGND
CNT1 PCB
D_5V
DAB_DA/TU_SDA
DAB_CLK/TU_CLK
Updating
TU_INT
TU_RST
3P WIRE
TU_SEN
DAB_TU_ON
SPK PCB
A_-12V
MUTE_B+ 13P WIRE
NC
BTOB 7P
BTOB 7P
MUTE_B+
A_+12V
3P WIRE
GND
GND
GND
NC
NC
29
SEMICONDUCTORS
Only major semiconductors are shown, general semiconductors etc. are omitted to list.
The semiconductor which described a detailed drawing in a schematic diagram are omitted to list.
Caution in
servicing
1. IC's
MB9AF344 (MAIN : IC101) Terminal Function
pin
Pin Name Alternate Symbol I/O Description
No
1 VCC - - -
2 P50 INT00_0/SIN3_1/MADATA00_1 TU_INT I/O TUNER INTERRUPT
3 P51 INT01_0/SOT3_1/MADATA01_1 EX_INTERRUPT I KEY EXIT REQUEST
4 P52 IN02_0/SCK3_1/MADATA02_1/MADATA02_1 DIR_INT1 I DIR INTERRUPT 1
5 P53 INT07_2/SIN6_0/TIOA1_2/MADATA03_1 DIR_INT2 I DIR INTERRUPT 2
6 P54 SOT6_0/TIOB1_2/MADATA04_1 LED_RED O RED LED
7 P55 SCK6_0/ADTG_1/MADATA05_1 LED_GREEN O GREEN LED
Electrical
8 P56 INT08_2/MADATA06_1 BT_P_ON O BT POWER SWITCH ON/OFF
9 P30 TIOB0_1/INT03_2/MADATA07_1 RMC I REMOCON INPUT
10 P31 TIOB1_1/SCK6_1/INT04_2/MADATA08_1 AMP_PROT I AMP PROTECTION
:'' 4%2-28C'6398C1%(C
11 P32 TIOB2_1/SOT6_1/INT05_2/MADATA09_1 PROT_V I POWER PROTECTION
4-28C7-2C1%(%8%C 4%27-2C-28C;/94
4-28C738C1%(%8%C 4%2738 C8-3&C 12 P33 INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA11_1 BT_REQ I BT POWER ON REQUEST
4-28C7'/C1%(%8%C 4%27'/C8-3%C 13 P39 ADTG_2 VOL_CE O NJW1194 CE
47-2C8-3%C-28C1%(%8%C 4&%2738C1%(C
4738C8-3&C1%(%8%C 4%%27-2C-28C1%(C
14 P3A TIOA0_1/RTCCO_2/SUBOUT_2 VOL_CLK O NJW1194_CLK
47'/C%(8+C1%(%8%C 4%27'/C1%(C 15 P3B TIOA1_1 VOL_DA O NJW1194_CA
4-28C1%(%8%C 4%2738C1%(C
16 P3C TIOA2_1 DAC_DEEMP O DAC DEEMPHASYS
48-3&C-28C1%(%8%C %:77
17 P3D TIOA3_1 DAC_MUTE O DAC MUTE
48-3&C7'/C-28C1%(%8%C
LQFP - 80 %:6,
48-3&C738C-28C1%(%8%C %:'' 18 P3E TIOA4_1 DAC_FLT O DAC FILTER
4-28C8-3&C7-2C%(8+C1%(%8 %C 4%27-2C-28C1%(C
19 P3F TIOA5_1 DAC_FMT O DAC OUT FORMAT
Mechanical
4%(8+C 4%27'/C1%(C
4%8-3%C68''3C79&398C 4%2738 C1%(C 20 VSS - - -
4&8-3%C 4%27-2C-28C1%(C
21 P44 TIOA4_0/MAD00_1 H/P_DET I HEADPHONE DETECTION
4'8-3%C 4%27'/C68''3C79&398C1%(C
4(8-3%C 4%2738C1%(C 22 P45 TIOA5_0/MAD01_1 H/P_MUTE O HEADPHONE MUTE
4)8-3%C 4%27-2C-28C;/941%(C 23 C - - -
4*8-3%C 4%2
:77 :''
24 VSS - - -
25 VCC - - -
26 X0A P46 SUB CLOCK - 32,768Hz
27 X1A P47 SUB CLOCK -
28 INITX - RESET - RESET
29 P48 INT14_1/SIN3_2/MAD02_1 VOL_UP I VOLUME ENCODER UP
Repair Information
30 P49 TIOB0_0/SOT3_2/MAD03_1 VOL_DOWN I VOLUME ENCODER DOWN
31 P4A TIOB1_0/SCK3_2/MAD04_1 EEPROM_SCL O EEPROM CLK
32 P4B TIOB2_0/MAD05_1 EEPROM_SDA I/O EEPROM DATA
33 P4C TIOB3_0/SCK7_1/CEC0/MAD06_1 PWR_ON O POWER ON/OFF
34 P4D TIOB4_0/SOT7_1/MAD07_1 DIR_DI I DIR DATA INPUT
35 P4E TIOB5_0/INT06_2/SIN7_1/MAD08_1 DIR_DO O DIR DATA OUTPUT
36 MD1 PE0 MD1 - UPGRADE MD1(GND)
37 MD0 - MD0 - UPGRADE MD0
38 X0 PE2 MAIN CLOCK - 4MHz
39 X1 PE3 MAIN CLOCK -
40 VSS - - -
41 VCC - - -
42 P10 AN00 SET_OPTION I SET OPTION
43 P11 AN01/SIN1_!/INT02_!/WKUP1/MAD09_1 CD_RX I CD UART INPUT
Updating
44 P12 AN02/SOT1_!/MAD10_1 CD_TX O CD UART OUTPUT
45 P13 AN03/SCK1_!/RTCCO_1/SUBOUT_1/MAD11_1 CD_RST O CD RESET
46 P14 AN04/INT03_1/SIN0_1/MAD12_1 DIR_RST O DIR RESET
47 P15 AN05/SOT0_1/MAD13_1 DIR_CLK O DIR CLOCK
48 P16 AN06/SCK0_1/MAD14_1 DIR_CE O DIR CE
49 P17 AN07/SIN2_2/INT04_1/MAD15_1 PWR_DN I AC PULSE INPUT
50 AVCC - - -
30
pin
No
Pin Name Alternate Symbol I/O Description BU9546KV (MAIN : IC104)
51 AVRH - - -
ANA_MONI1
ANA_MONI0
Caution in
TEST_OUT
52 AVSS - - -
AD_MONI1
AD_MONI0
servicing
TEST_IN
TEST6
TEST5
TEST4
DGND
DGND
53 P18 AN08/SOT2_2/MAD16_1 TU_RST O TUNER RESET
DVDD
DVDD
EQO
RFI
XO
54 P19 AN09/SCK2_2/MAD17_1 DAB_CLK/TU_CLK O DAB CLOCK / TUNER CLOCK
55 P1A AN10/SIN4_1/INT05_1/MAD18_1 DAB_DA/TU_SDA I/O DAB DATA / TUNER DATA
DAB POWER ON / TUNER POWER
56 P1B AN11/SOT4_1/MAD19_1 DAB_ON/TU_ON O
ON
57 P23 AN16/SCK0_0/TIOA7_1 KEY2 I KEY INPUT 2
58 P22 AN17/SOT0_0/TIOB7_1 TX O UPDATE TX
59 P21 AN18/SIN0_0/INT06_1 RX I UPDATE RX
60 P20 AN19/INT05_1/CROUT_0/MAD24_1 KEY1 I KEY INPUT 1
61 P00 TRSTX/MCSX7_1 JTRSTX - JTAG
62 P01 TCK/SWCLK JTCK - JTAG
63 P02 TDI/MCSX6-1 JTDI - JTAG
Electrical
64 P03 TMS/SWDIO JTMS - JTAG
65 P04 TDO/SWO JTDO - JTAG
66 P07 AN22/ADTG_0/MCLKOUT1/TRACED2/ACK4_2 TU_SEN O TUNER SENSE
67 P0A SIN4_0/INT00_2/MCSX1_1 BT_RX I BT RX INTERRUPT
68 P0B SOT4_0/TIOB6_1/MCSX0_1 VFD_CLK O VFD CLOCK
69 P0C SCK4_0/TIOA6_1/MALE_1 VFD_DA O VFD DATA
MCK
DIN/DOUT
DVDD
BUSY
VDD_CORE
CLK
DGND
SUBSYQ
CLK88
XBUFO
R/W
SUBDATA
SUBCK
RESETB
DGND
WFCK
70 P0D RTS4_0/TIOA3_2/MDQM0_1 VFD_CE O VFD CE
71 P0E CTS4_0/TIOB3_2/MDQM1_1 VFD_RST O VFD RESET
72 P0F NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0 - O
73 P63 INT03_0/MWEX_1 - O
Terminal Function
74 P62 SCK5_0/ADTG_3/MOEX_1 SPK_OPTIMIZER O SPEAKER OPTIMIZE RELAY ON/OFF Pin Description(s)
Mechanical
75 P61 SOT5_0/TIOB2_2/UHCONX AUDIO_MUTE O AUDIO MUTE Pin No. Pin Name Description of terminals Pin No. Pin Name Description of terminals
76 P60 SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1 MAIN_MUTE O SPEAKER RELAY ON/OFF 1 AVDD1 Analog power terminal 33 DVDD I/O digital power terminal
2 AC A + C voltage input 34 DOUTA Audio data output
77 VCC - - - 3 BD B + D voltage input 35 LRCK Audio LR signal output
78 P80 UDM0 - O 4 VBIAS Bias level 36 DCK Audio clock output
5 AGND1 Analog GND 37 VDD_CORE Internal digital power terminal
79 P81 UDP0 CD_P_ON O Power 3V On 6 E E voltage input 38 TEST0 Test signal I/O
80 VSS - - - 7 F F voltage input 39 TEST1 Test signal I/O
8 PD Photo detector input 40 TEST2 Test signal I/O
9 LD Laser drive output 41 TEST3 Test signal I/O
10 ASY For asymmetric correction 42 DGND Digital GND terminal
11 PCO PLL PCO output terminal 43 FLAG0 Various flag output terminal
12 FCO PLL FCO-DAC output terminal 44 FLAG1 Various flag output terminal
13 FDOUT Focus drive output terminal 45 FLAG2 Various flag output terminal
14 TDOUT Tracking drive output terminal 46 FLAG3 Various flag output terminal
Repair Information
15 SDOUT Sled drive output terminal 47 DVDD I/O digital power terminal
X'tal 16.9344MHz connecting
16 CLVOUT CLV drive output terminal 48 XI
(input) terminal
17 DVDD I/O digital power terminal 49 XO X'tal 16.9344MHz
Sub Q and command transfer
18 MCK 50 DGND Digital GND terminal
clock input terminal
Command input and status and
19 DIN/DOUT 51 TEST_IN Test signal input terminal
sub Q output terminal
Command read/write signal
20 R/W 52 TEST_OUT Test signal output terminal
input terminal
21 BUSY Busy signal output terminal 53 DVDD I/O digital power terminal
22 SUBSYQ Sub code synchronous 54 DGND Digital GND terminal
23 SUBDATA Sub code data output 55 TEST4 Test signal I/O
24 SUBCK Sub code bit clock 56 TEST5 Test signal I/O
25 WFCK Disk frame synchronous signal 57 TEST6 Test signal I/O
26 VDD_CORE Internal digital power terminal 58 DVDD I/O digital power terminal
27 DGND Digital GND terminal 59 AD_MONI0 Test signal input/monitor
Test signal input/monitor
28 CLK Output terminal for various clocks 60 AD_MONI1
signal output terminal
Analog test signal
Clock output terminal for driver
29 CLK88 61 ANA_MONI0 input/monitor signal output
IC
Updating
terminal
Analog test signal
System reset terminal
30 RESETB 62 ANA_MONI1 input/monitor signal output
(“L” → reset condition)
terminal
31 XBUFO X'tal 16.9344MHz output 63 RFI RF output capacity
After-RF-equalizer
32 DGND Digital GND terminal 64 EQO
output terminal
31
AM5888S (MAIN : IC105) NJW1194V (MAIN : IC115)
MUTE BIAS VINTK TRB_2 NC VINLD GND VCTL NC VCC2 VOLD- VOLD+ VOTK- VOTK+
32 17
Caution in
28 27 26 25 24 23 22 21 20 19 18 17 16 15
servicing
GND PGND No. Pin Name No. Pin Name
10K
Vcc2 1 InA1 17 Tone_Ba2b
15K
MUTE 2 InA2 18 Tone_Ba1b
10K
-
+
Driver(4X) Driver(6x)
-
25K
4 InA4 20 GND
+
Thermal
Shut down 5 GND 21 V -
Vcc2
Vcc2 6 DCCAP_A 22 V +
Vcc1
25K 10K 7 GND 23 A DR0
+
-
+ -
8 Out A 24 A DR1
Sled Actuator
+
25K
Driver(4X) Driver(6x) 9 V DDOUT 25 Out B
-
Pre-DRV 10 DATA 26 GND
TRAY
DRIVER
PGND Vcc1 11 CLOCK 27 DCCAP_B
10K
12 LATCH 28 GND
Electrical
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VINFC TRB_1 REGO2 VINSL+
13 GND 29 I nB4
REGO1 FWD REV VCC1 VOTR- VOTR+ VOSL+ VOSL- VOFC- VOFC+
14 Tone_Tr1a 30 I nB3
1 16 15 Tone_Ba1a 31 I nB2
16 Tone_Ba2a 32 I nB1
Pin Discriptions
PIN No Pin Name Function
1 VINFC Input for focus driver
Block Diagram
2 TRB_1 Connect to external transistor base
$FK7RQH)LOWHU
3 REGO2 Regulator voltage output, connect to external transistor collector
4 VINSL+ Input for the sled driver
9 *1' 9 9
5 REGO1 Regulator voltage output, connect to external transistor collector
Mechanical
6 FWD Tray driver forward input
7 REV Tray driver reverse input
8 Vcc1 Vcc for pre-drive block and power block of sled and tray
9 VOTR- Tray driver output (-) %LDV &RQWURO/RJLF
,Q$
10 VOTR+ Tray driver output (+)
,Q$ =HUR&URVV'HWHFWLRQ
11 VOSL+ Sled driver output (+)
12 VOSL- Sled driver output (-) ,Q$
13 VOFC- Focus driver output (-) ,Q$ 2XW$
14 VOFC+ Focus driver output (+) 721(
Repair Information
15 VOTK+ Tracking driver output (+) ,Q%
16 VOTK- Tracking driver output (-) ,Q%
17 VOLD+ Spindle driver output (+)
,Q% 2XW%
18 VOLD- Spindle driver output (-) 721(
,Q%
19 Vcc2 Vcc for power block of spindle, tracking and focus
20 NC No Connection
21 VCTL Speed control input of tray driver
22 GND Ground
23 VINLD Input for spindle driver
24 NC No Connection
25 TRB_2 Connect to external transistor base
26 VINTK Input for tracking driver %FK7RQH)LOWHU
27 BIAS Input for reference voltage
Updating
28 MUTE Input for mute control
Notes) Symbol of + and – (output of drivers) means polarity to input pin.
(For example, if voltage of pin1 is high, pin14 is high.)
32
PCM9211
PCM5100A (MAIN : IC124) DIR PCM9211 (MAIN : IC127)
PW 20-Pin Package www.ti.com SBAS495 – JUNE 2010
Caution in
(Top View)
servicing
PIN CONFIGURATIONS
PT PACKAGE
LQFP-48
(TOP VIEW)
AGNDAD
GNDRX
VCCAD
VCOM
RXIN0
AGND
VINR
VINL
VCC
XTO
FILT
XTI
48 47 46 45 44 43 42 41 40 39 38 37
ERROR/INT0 1 36 VDDRX
Pin Functions
NPCM/INT1 2 35 RXIN1
Electrical
PIN
TYPE DESCRIPTION
NAME NO. MPIO_A0 3 34 RST
AGND 9 — Analog ground
MPIO_A1 4 33 RXIN2
AVDD 8 P Analog power supply, 3.3 V
BCK 13 I Audio data bit clock input (1) MPIO_A2 5 32 RXIN3
CAPM 4 O Charge pump flying capacitor terminal for negative rail
MPIO_A3 6 31 RXIN4/ASCKIO
CAPP 2 O Charge pump flying capacitor terminal for positive rail
PCM9211
CPGND 3 — Charge pump ground MPIO_C0 7 30 RXIN5/ABCKIO
CPVDD 1 P Charge pump power supply, 3.3 V
(1) MPIO_C1 8 29 RXIN6/ALRCKIO
DEMP 10 I De-emphasis control for 44.1-kHz sampling rate : Off (Low) / On (High)
DGND 19 — Digital ground MPIO_C2 9 28 RXIN7/ADIN0
DIN 14 I Audio data input (1)
MPIO_C3 10 27 MODE
DVDD 20 P Digital power supply, 1.8 V or 3.3 V
FLT 11 I Filter select : Normal latency (Low) / Low latency (High)
Mechanical
MPIO_B0 11 26 MS/ADR1
FMT 16 I Audio format selection : I2S (Low) / Left-justified (High)
LDOO 18 P Internal logic supply rail terminal for decoupling, or external 1.8 V supply terminal MPIO_B1 12 25 MC/SCL
LRCK 15 I Audio data word clock input (1)
OUTL 6 O Analog output from DAC left channel 13 15 16 18 19 20 23
14 17 21 22 24
OUTR 7 O Analog output from DAC right channel
System clock input (1)
DVDD
DOUT
MPO0
MPO1
SCKO
DGND
MPIO_B2
BCK
MDI/SDA
LRCK
MPIO_B3
MDO/ADR0
SCK 12 I
VNEG 5 O Negative charge pump rail terminal for decoupling, –3.3 V
XSMT 17 I Soft mute control (1): Soft mute (Low) / soft un-mute (High)
PIN FUNCTIONS
PIN
Repair Information
5-V
NO. NAME I/O TOLERANT DESCRIPTION
1 ERROR/INT0 O No DIR Error detection output / Interrupt0 output
2 NPCM/INT1 O No DIR Non-PCM detection output / Interrupt1 output
3 MPIO_A0 I/O Yes Multipurpose I/O, Group A (1)
4 MPIO_A1 I/O Yes Multipurpose I/O, Group A (1)
5 MPIO_A2 I/O Yes Multipurpose I/O, Group A (1)
6 MPIO_A3 I/O Yes Multipurpose I/O, Group A (1)
7 MPIO_C0 I/O Yes Multipurpose I/O, Group C (1)
8 MPIO_C1 I/O Yes Multipurpose I/O, Group C (1)
9 MPIO_C2 I/O Yes Multipurpose I/O, Group C (1)
10 MPIO_C3 I/O Yes Multipurpose I/O, Group C (1)
11 MPIO_B0 I/O Yes Multipurpose I/O, Group B (1)
12 MPIO_B1 I/O Yes Multipurpose I/O, Group B (1)
Updating
13 MPIO_B2 I/O Yes Multipurpose I/O, Group B (1)
14 MPIO_B3 I/O Yes Multipurpose I/O, Group B (1)
15 MPO0 O No Multipurpose output 0
33
SBAS495 – JUNE 2010 www.ti.com www.ti.com SBAS495 – JUNE 2010
DIR PCM9211 Block Diagram
PIN FUNCTIONS (continued) BLOCK DIAGRAM
PIN
FILT
Caution in
5-V
servicing
NO. NAME I/O TOLERANT DESCRIPTION
AUXIN 0
16 MPO1 O No Multipurpose output 1
AUTO
RXIN7
17 DOUT O No Main output port, serial digital audio data output RXIN 0 RXIN0 DIR DIR SCKO
21 DGND – – Ground, for digital RXIN 4/ASCKI 0 RXIN4 Lock :DIR AUXIN2
Unlock:ADC
22 DVDD – – Power supply, 3.3 V (typ.), for digital RXIN 5/ABCKI 0 RXIN5 Clock/ Data
Recovery
Software control I/F, SPI data output / I2C slave address setting0 (2)
RXIN 6/ALRCKI 0 RXIN6
23 MDO/ADR0 I/O Yes
RXIN 7/ADIN0 RXIN7 AUTO
24 MDI/SDA I/O Yes Software control I/F, SPI data input / I2C data input/output (2) (3)
DIR
25 MC/SCL I Yes Software control I/F, SPI clock input / I2C clock input (2) MPIO_ A0 RXIN8 ADC
2 (2) Lock Detection
26 MS/ADR1 I Yes Software control I/F, SPI chip select / I C slave address setting1
Electrical
MPIO_ A1 DIT
RXIN9 AUXIN0
MPIO_ A
27 MODE I No Control mode setting, (see the Serial Control Mode section, Control Mode Pin Setting) MPIO_ A2
SELECTOR RXIN10 AUXIN1
28 RXIN7/ADIN0 I Yes Biphase signal, input 7 / AUXIN0, serial audio data input (2) MPIO_ A3 RXIN11 RECOUT 0 AUXIN2
29 RXIN6/ALRCKI0 I Yes Biphase signal, input 6 / AUXIN0, LR clock input (2) DITOUT RECOUT 1
30 RXIN5/ABCKI0 I Yes Biphase signal, input 5 / AUXIN0, bit clock input (2) RECOUT0
MPO 0
31 RXIN4/ASCKI0 I Yes Biphase signal, input 4 / AUXIN0, system clock input (2)
RECOUT1 MPO0/1
SELECTOR MPO 1
ADC DITOUT
(2)
32 RXIN3 I Yes Biphase signal, input 3 VINL
ADC Mode
33 RXIN2 I Yes Biphase signal, input 2 (2) VINR ADC Control
Mechanical
DIR
38 GNDRX - - Ground, for RXIN ADC Standalone
MPIO _C1 ADC MPIO_B1
(5)
39 XTI I No Oscillation circuit input for crystal resonator or external XTI clock source input MPIO _C2
MPIO_ C AUXOUT MPIO _B
MPIO_B2
SELECTOR AUXIN0
AUXIN 2 SELECTOR
40 XTO O No Oscillation circuit output for crystal resonator MPIO _C3
AUXIN1
AUXIN1 MPIO_B3
44 VCOM O No ADC common voltage output; must connect external decoupling capacitor XTI Divider
XTO OSC
45 AGNDAD – – Ground, for ADC analog
XMCKO SBCK /SLRCK
Secondary BCK / LRCK
46 VCCAD – – Power supply, 5.0 V (typ.), for ADC analog XMCKO (To MPIO _A & MPO0/1 )
Divider
( to MPIO_A )
Divider
47 VINL I No ADC analog voltage input, left channel Selector
Repair Information
48 VINR I No ADC analog voltage input, right channel
MC /SCL REGISTER EXTRA DIR FUNCTIONS ERROR /INT0
(2) Schmitt trigger input
Open-drain configuration in I2C mode
DIR DIR
(3) MDI /SDA
2
SPI/I C
Function
Control
DIR CS
( 48-bit) PC and PD fS Calculator
ERROR DETECTION NPCM /INT1
(4) Onboard pull-down resistor (50 kΩ, typical) MDO /ADR 0 INTERFACE
Non-PCM DETECTION
Updating
8 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated
34
2. FL DISPLAY
16-ST-103GINK (MAIN : FL501) PATTERN DETAIL
Caution in
servicing
Upper Lower
16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G 1-1A 2-1A 3-1A 4-1A 5-1A 1-1B 2-1B 3-1B 4-1B 5-1B
1-2A 2-2A 3-2A 4-2A 5-2A 1-2B 2-2B 3-2B 4-2B 5-2B
1-3A 2-3A 3-3A 4-3A 5-3A 1-3B 2-3B 3-3B 4-3B 5-3B
1-4A 2-4A 3-4A 4-4A 5-4A 1-4B 2-4B 3-4B 4-4B 5-4B
1 43
Electrical
PIN CONNECTION 1-5A 2-5A 3-5A 4-5A 5-5A 1-5B 2-5B 3-5B 4-5B 5-5B
CONNECTION PIN NO.
14
15
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
1
2
3
4
-
1-6A 2-6A 3-6A 4-6A 5-6A 1-6B 2-6B 3-6B 4-6B 5-6B
1-7A 2-7A 3-7A 4-7A 5-7A 1-7B 2-7B 3-7B 4-7B 5-7B
RESET
PGND
LGND
VDD
OSC
TSA
TSB
DA
NC
NX
VH
NP
NP
NP
NP
CP
CS
F2
F1
ANODE CONNECTION
T21 T20 T19 T18 T17 T16-T1 T21 T20 T19 T18 T17 T16-T1
Mechanical
2) NP ------No pin D3A - - - - - 4-1A D3B - - - - - 4-1B
Repair Information
10) CP ----Shift Register Clock D16A - - - - - 2-4A D16B - - - - - 2-4B
D17A - - - - - 3-4A D17B - - - - - 3-4B
11) DA ----Serial Data Input D18A - - - - - 4-4A D18B - - - - - 4-4B
Updating
AD1 -
AD2 -
AD3 -
AD4 - - - -
35
3. Remote Code Table
KEY CODE (Kaseikyo)
Caution in
servicing
RCD-M41:RC-1214 Maker Code(C0C1) Byte 1 Byte 2
1 2 3 4 M40 Remarks DENON(3254H) 00101010 01001100
Power 1 SLEEP
basic setup 2 CLOCK
3 DIMMER KEY No. Name Genre 1(D0) Genre 2(D1) DATA Code (D2) Parity (DP) Byte 3 Byte 4 Byte 5 Byte 6
4 POWER KEY1 SLEEP SYSTEM (5H) SYSTEM (1H) SLEEP (431H) 02H 00001010 10001000 11000010 01000000
5 6 7 CD
5 KEY2 CLOCK SYSTEM (5H) SYSTEM (1H) CLOCK(434H) 52H 00001010 10000010 11000010 01001010
6 TUNER KEY3 DIMMER SYSTEM (5H) SYSTEM (1H) DIMMER(433H) 22H 00001010 10001100 11000010 01000100
7 Bluetooth KEY4 POWER SYSTEM (5H) SYSTEM (1H) POWER ON/STANDBY(403H) 21H 00001010 10001100 00000010 10000100
8 9 10 source select OPTICAL IN 1
8 KEY5 CD SYSTEM (5H) AUDIO PLAYER(3H) (/FUNCTION)CD(407H) 63H 00001010 11001110 00000010 11000110
9 OPTICAL IN 2 KEY6 TUNER SYSTEM (5H) TUNER (6H) (/FUNCTION)TUNER (407H) 66H 00001010 01101110 00000010 01100110
10 ANALOG IN KEY7 Bluetooth SYSTEM (5H) AMP/RECEIVER (2H) BLUETOOTH(41DH) C3H 00001010 01001011 10000010 11000011
11 12 13
11 KEY8 OPTICAL IN 1 SYSTEM (5H) AMP/RECIEVER (2H) (/FUNCTION)OPTICAL(414H) 53H 00001010 01000010 10000010 11001010
12 KEY9 OPTICAL IN 2 SYSTEM (5H) AMP/RECIEVER (2H) (/FUNCTION)OPTICAL2(41CH) D3H 00001010 01000011 10000010 11001011
14 15 16 13 KEY10 ANALOG IN SYSTEM (5H) AMP/RECIEVER (2H) (/FUNCTION)AUX1(408H) 92H 00001010 01000001 00000010 01001001
14 |<< KEY11
playback 15 PLAY/ PAUSE KEY12
operation 16 >>|
17 18 19 KEY13
17 <</TU - KEY14 |<< SYSTEM (5H) SYSTEM (1H) |<< (40DH) C1H 00001010 10001011 00000010 10000011
18 STOP
KEY15 PLAY/ PAUSE SYSTEM (5H) SYSTEM (1H) PLAY/PAUSE(40AH) B1H 00001010 10000101 00000010 10001101
Electrical
19 >>/TU +
KEY16 >>| SYSTEM (5H) SYSTEM (1H) >>| (40CH) D1H 00001010 10000011 00000010 10001011
20 21 22 20 CH+
KEY17 <</TU - SYSTEM (5H) SYSTEM (1H) <</TU- (40FH) E1H 00001010 10001111 00000010 10000111
21 SDB/TONE
basic operation KEY18 STOP SYSTEM (5H) SYSTEM (1H) STOP (43FH) E2H 00001010 10001111 11000010 01000111
22 VOLUME up
KEY19 >>/TU + SYSTEM (5H) SYSTEM (1H) >>/TU+ (40EH) F1H 00001010 10000111 00000010 10001111
23 CH-
MUTE KEY20 CH+ SYSTEM (5H) TUNER (6H) CH+(40CH) D6H 00001010 01100011 00000010 01101011
23 24 25 24
VOLUME down KEY21 SDB/TONE SYSTEM (5H) SYSTEM (1H) TONE(/SDB)(430H) 12H 00001010 10000000 11000010 01001000
25 KEY22 VOLUME up SYSTEM (5H) SYSTEM (1H) VOLUME+ (404H) 51H 00001010 10000010 00000010 10001010
26 FOLDER / ALL
UP KEY23 CH- SYSTEM (5H) TUNER (6H) CH-(40DH) C6H 00001010 01101011 00000010 01100011
26 28 27
INFO KEY24 MUTE SYSTEM (5H) SYSTEM (1H) MUTE (406H) 71H 00001010 10000110 00000010 10001110
27 28
LEFT KEY25 VOLUME down SYSTEM (5H) SYSTEM (1H) VOLUME- (405H) 41H 00001010 10001010 00000010 10000010
29
30 ENTER KEY26 FOLDER / ALL SYSTEM (5H) SYSTEM (1H) FOLDER(42DH) C3H 00001010 10001011 01000010 11000011
31 RIGHT KEY27 UP SYSTEM (5H) SYSTEM (1H) CURSOR UP (420H) 13H 00001010 10000000 01000010 11001000
29 30 31 MENU 32 DAB/RDS KEY28 INFO SYSTEM (5H) SYSTEM (1H) DISPLAY(/TIME) (432H) 32H 00001010 10000100 11000010 01001100
operation DOWN KEY29 LEFT SYSTEM (5H) SYSTEM (1H) CURSOR LEFT (422H) 33H 00001010 10000100 01000010 11001100
33
34 SETUP KEY30 ENTER SYSTEM (5H) SYSTEM (1H) ENTER (424H) 53H 00001010 10000010 01000010 11001010
35 1 KEY31 RIGHT SYSTEM (5H) SYSTEM (1H) CURSOR RIGHT (423H) 23H 00001010 10001100 01000010 11000100
33 2 KEY32 DAB/RDS SYSTEM (5H) TUNER(6H) DAB/RDS(42AH) B4H 00001010 01100101 01000010 00101101
32 34 36
37 3 KEY33 DOWN SYSTEM (5H) SYSTEM (1H) CURSOR DOWN (421H) 03H 00001010 10001000 01000010 11000000
Mechanical
38 4 KEY34 SETUP SYSTEM (5H) SYSTEM (1H) (/SYSTEM)MENU(440H) 15H 00001010 10000000 00100010 10101000
39 5 KEY35 1 SYSTEM (5H) SYSTEM (1H) 1 (411H) 00H 00001010 10001000 10000010 00000000
35 36 37 6 KEY36 2 SYSTEM (5H) SYSTEM (1H) 2 (412H) 30H 00001010 10000100 10000010 00001100
40
41 7 KEY37 3 SYSTEM (5H) SYSTEM (1H) 3 (413H) 20H 00001010 10001100 10000010 00000100
42 8 KEY38 4 SYSTEM (5H) SYSTEM (1H) 4 (414H) 50H 00001010 10000010 10000010 00001010
38 39 40 9 KEY39 5 SYSTEM (5H) SYSTEM (1H) 5 (415H) 40H 00001010 10001010 10000010 00000010
43
10 key 44 +10 KEY40 6 SYSTEM (5H) SYSTEM (1H) 6 (416H) 70H 00001010 10000110 10000010 00001110
45 0 KEY41 7 SYSTEM (5H) SYSTEM (1H) 7 (417H) 60H 00001010 10001110 10000010 00000110
41 42 43 CLEAR
46 KEY42 8 SYSTEM (5H) SYSTEM (1H) 8 (418H) 90H 00001010 10000001 10000010 00001001
47 RANDOM KEY43 9 SYSTEM (5H) SYSTEM (1H) 9 (419H) 80H 00001010 10001001 10000010 00000001
48 REPEAT KEY44 +10 SYSTEM (5H) SYSTEM (1H) +10(41CH) D0H 00001010 10000011 10000010 00001011
44 45 46
49 PROGRAM KEY45 0 SYSTEM (5H) SYSTEM (1H) 0 (41BH) A0H 00001010 10001101 10000010 00000101
50 REMOTE/BROWSE KEY46 CLEAR SYSTEM (5H) SYSTEM (1H) CLEAR(42FH) E3H 00001010 10001111 01000010 11000111
RANDOM
47 48 49 50 REPEAT
KEY47 RANDOM SYSTEM (5H) SYSTEM (1H) RANDOM (42AH) B3H 00001010 10000101 01000010 11001101
PROGRAM KEY48 REPEAT SYSTEM (5H) SYSTEM (1H) REPEAT (42BH) A3H 00001010 10001101 01000010 11000101
KEY49 PROGRAM SYSTEM (5H) SYSTEM (1H) PROGRAM(429H) 83H 00001010 10001001 01000010 11000001
Repair Information
REMOTE/B
KEY50 REMOTE/BROWSE SYSTEM (5H) PORTABLE (7H) REMOTE/BROWSE(42DH) C5H 00001010 11101011 01000010 10100011
Extended Code
1 POWER ON SYSTEM (5H) SYSTEM (1H) POWER ON (401H) 01H 00001010 10001000 00000010 10000000
2 POWER OFF SYSTEM (5H) SYSTEM (1H) POWER OFF (402H) 31H 00001010 10000100 00000010 10001100
3 DAB SYSTEM (5H) TUNER (6H) DAB (40AH) B6H 00001010 01100101 00000010 01101101
4 FM SYSTEM (5H) TUNER (6H) FM (409H) 86H 00001010 01101001 00000010 01100001
5 AM SYSTEM (5H) TUNER (6H) AM (408H) 96H 00001010 01100001 00000010 01101001
6 CD PLAY SYSTEM (5H) AUDIO PLAYER(3H) PLAY(/CD) (408H) 93H 00001010 11000001 00000010 11001001
7 USB PLAY SYSTEM (5H) AUDIO PLAYER(3H) PLAY(/USB) (421H) 01H 00001010 11001000 01000010 10000000
8 PAUSE SYSTEM (5H) SYSTEM (1H) PAUSE (409H) 81H 00001010 10001001 00000010 10000001
9 DISC(/All)(/descrete) SYSTEM (5H) SYSTEM (1H) DISC(/All)(/descrete) (439H) 82H 00001010 10001001 11000010 01000001
10 Folder(/descrete) SYSTEM (5H) SYSTEM (1H) Folder(/descrete) (438H) 92H 00001010 10000001 11000010 01001001
Updating
36
MECHANICAL
DISASSEMBLY
Caution in
servicing
Flowchart
1. LOADER PANEL
2. FRONT PANEL ASSY
3. MECHA ASSY
4. HEAT SINK SUB ASSY
5. REAR PANEL
6. PCB ASSY
Electrical
7. MAIN PCB
8. TRANS
EXPLODED VIEW
PACKING VIEW
Mechanical
Repair Information
Updating
37
DISASSEMBLY
Flowchart
• Remove each part following the flow below.
Caution in
servicing
• Reassemble the removed parts in the reverse order.
• Read "SAFETY PRECAUTIONS" before reassembling the removed parts.
• If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work. Failure to shape the wires correctly may cause problems such as noise.
• See "EXPLODED VIEW"
TOP COVER
Electrical
LOADER PANEL HEAT SINK SUB ASSY REAR PANEL
DISASSEMBLY DISASSEMBLY DISASSEMBLY
1. LOADER PANEL 4. HEAT SINK SUB ASSY 5. REAR PANEL
and "EXPLODED VIEW" and "EXPLODED VIEW" and "EXPLODED VIEW"
LOADER PANEL GUIDE_R PCB BACK
Ref. No. of EXPLODED VIEW : P 2 Ref. No. of EXPLODED VIEW : P 7 Ref. No. of EXPLODED VIEW : 3
GUIDE_F PCB
Ref. No. of EXPLODED VIEW : P 8
FRONT PANEL ASSY REGULATOR 2 PCB PCB ASSY
Ref. No. of EXPLODED VIEW : P 14
Mechanical
DISASSEMBLY DISASSEMBLY
2. FRONT PANEL ASSY AMP PCB 6. PCB ASSY
and "EXPLODED VIEW" Ref. No. of EXPLODED VIEW : P 9 and "EXPLODED VIEW"
FRONT PCB ST_BY PCB
Ref. No. of EXPLODED VIEW : P 10 Ref. No. of EXPLODED VIEW : P 12
BLUETOOTH MODULE INPUT PCB
Ref. No. of EXPLODED VIEW : 22 Ref. No. of EXPLODED VIEW : P 2
CNT2 PCB
Ref. No. of EXPLODED VIEW : P 4
Repair Information
MECHA ASSY SPK PCB
DISASSEMBLY Ref. No. of EXPLODED VIEW : P 11
3. MECHA ASSY CNT1 PCB
and "EXPLODED VIEW" Ref. No. of EXPLODED VIEW : P 3
CD MECHA DAB PCB
Ref. No. of EXPLODED VIEW : 12 Ref. No. of EXPLODED VIEW : P 13
Updating
DISASSEMBLY DISASSEMBLY
7. MAIN PCB 8. TRANS
and "EXPLODED VIEW" and "EXPLODED VIEW"
MAIN PCB TRANS
Ref. No. of EXPLODED VIEW : P 1 Ref. No. of EXPLODED VIEW : 13
38
Explanatory Photos for DISASSEMBLY 2. FRONT PANEL ASSY
• For the shooting direction of each photos used in this manual, see the photo below.
• A, B, C and D in the photo below indicate the shooting directions of photos. Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY
Caution in
servicing
• The photographs with no shooting direction indicated were taken from the top of the unit. (1) Remove the screws.
• Photos of RCD-M41 E1C are used in this manual.
The viewpoint of each photograph
↓Shooting direction: D↓
↑Shooting direction: C↑
(Shooting direction : X) [View from the top]
x2 x3
↓Shooting direction: B↓
Electrical
↓Shooting direction: C↓
↑Shooting direction: D↑
(2) Remove the STYLE PINs and connectors. Remove the FFC.
↓Shooting direction: C↓
Bluetooth MODULE
CP705
↑Shooting direction: D↑
Mechanical
↑Shooting direction: A↑
STYLE PIN
1. LOADER PANEL
Proceeding : TOP COVER → LOADER PANEL CP502
(1) Open the CD tray and remove LOADER PANEL. Remove the AC power cord.
Repair Information
NOTE: Please remove slowly so as not to damage the hook of Tray and LOADER PANEL. (3) Remove the FFC.
MAIN PCB
FPC101
Updating
39
3. MECHA ASSY 4. HEAT SINK SUB ASSY
Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY → MECHA ASSY Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY → MECHA ASSY
Caution in
servicing
(1) Remove the screws. → HEAT SINK SUB ASSY
Caution : Remove the FFC cable after the CD mecha's short circuit pattern for LD damage prevention
(1) Remove the screws.
has been short circuited.
↑Shooting direction: C↑
CN102
CN101
x1 x5
Caution
Electrical
View from the bottom
x3
MAIN PCB
(2) Remove the connector.
Mechanical
CP703
(2) Remove the FFC cable after the CD mecha's short circuit pattern for LD damage prevention has
been short circuited.
Be sure to wear an earth band.
CP706
CP505
Repair Information
Soldering place
Updating
40
5. REAR PANEL 7. MAIN PCB
Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY → MECHA ASSY Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY → MECHA ASSY
Caution in
servicing
→ HEAT SINK SUB ASSY → REAR PANEL → HEAT SINK SUB ASSY → REAR PANEL → PCB ASSY → MAIN PCB
(1) Remove the screws. (1) Remove the screws.
FFC
x3 x11 x3
Electrical
View from the bottom
6. PCB ASSY
Mechanical
Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY → MECHA ASSY 8. TRANS
→ HEAT SINK SUB ASSY → REAR PANEL → PCB ASSY
Proceeding : TOP COVER → LOADER PANEL → FRONT PANEL ASSY → MECHA ASSY
(1) Remove the screws. Remove the connector. Cut the wire clamps, then remove the STYLE PINs.
→ HEAT SINK SUB ASSY → REAR PANEL → PCB ASSY → TRANS
CN113 See "EXPLODED VIEW" for instructions on removing the transformer (TRANS).
Repair Information
CN104
x4 CUT
CN512
CN504
CLP501
CN509 STYLE PIN
CP503
Updating
41
EXPLODED VIEW
Parts List kNote: The following Serial number is using the parts(30).
https://dmedia.soundunited.com/documents/details/23162 Others are not used.
• RCDM41BTBKE3-------until AUT36790906883
Caution in
servicing
• RCDM41BTBKE2-------until AUG36400109830
• RCDM41BTDABBKEK-until AUJ36200140104
30 • RCDM41BTSPE2-------until AUN36391217010
• RCDM41BTSP-----------until AUH36491009543
S5X4
1
3
S5X11
S6X2
S5X9Only DAB
Electrical
24
12-2 S3X4 S1 X2
12 P12
6
2 S1X3
P2
S1 X4 P3 35 S8X1
28
16
11 P1
36 29
Mechanical
15
P6 S4 X1 P13 Only DAB
13
P4
23 34 S1 X1
P11
22
P10
S1 X1
z S1X1
S1X6 S3X4 S4 X3
P5
18 21 27 32 X2
S1X3 19
Repair Information
S1 X1
33 S1X1 14 27
17 8 31
S1X2
25
30 P8
20
P9
4 S1X1
33 S7 X2
P7
S1X2
7
9 X4
P14
Updating
26 S7X4
S1X2 Only SL MODEL S1X8
S2 X4
5
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
42
PACKING VIEW
Parts List
https://dmedia.soundunited.com/documents/details/23162
Caution in
servicing
4
7-11. ZIPPERBAG(A4size)
7-1. Notes on RADIO
Electrical
1
7-6. FM Antenna (E3/E2/E1C/JP)
DAB Antenna (EK Only)
7-10. Antenna Isolator
(E1C only) 21
20
7-7. CARD PASS Front 19
12 14
7-5. AM Antenna(E3/E1C/JP Only)
(E1C only)
Mechanical
13
10 3 z
7
2
3 8
Repair Information
5
9 DEN
ON
ON
DEN
15
SPEAKER TERMINAL BUSHING * BOX BOTTOM TAPING
Updating
17 2
16
43
REPAIR INFORMATION
TROUBLE SHOOTING SPECIAL MODE
Caution in
servicing
1. The unit does not power on (No.1) Special mode setting button
2. The unit does not power on (No.2) 1. Version Display Mode
3. VFD is not lit 2. Display check mode
4. The disc does not load, does not play, or "UNSUPPORTED" is indicated on the 3. Initialization Mode
FL display, etc. 4. Test mode
5. No audio output from Tuner 4-1. Disc mounting
6. No audio output from DAB (EK Only) 4-2. Servo check
Electrical
7. No audio output from Bluetooth. 4-3. Pickup movement
8. No audio output from this unit. 4-4. Stop
4-5. All servo on
Mechanical
5-2. Chucking mode
NOTES ON HANDLING AND REPLACEMENT OF 5.3. Error display
6. Accumulated laser on time display mode
THE LASER PICK-UP 7. Protection History Display Mode
1. Protection of the LD 8. Version Display of DAB Module (RCD-M41DAB Only)
2. Precautions when handling the laser CD mechanism
3. Cautions on assembling and adjustment
ADJUSTMENT
Repair Information
h
4. Notes on Handling the Laser Pick-Up
Updating
44
TROUBLE SHOOTING
1. The unit does not power on (No.1) 2. The unit does not power on (No.2)
NO NO Check the state / soldering for the following parts.
Caution in
Check Power Supply Voltages for +3V3_ST
servicing
ST-BY PART
The red LED is blinking. TO "2. The unit does not power on (No.2)" ST-BY PART
[IC505, T501]
[CN512 : 7pin (3.3V)]
Other connected circuits.
YES YES
Check Power Supply Voltages for PWR_ON. NO Check the PWR_DN signal. NO
Check the state / soldering for the following parts. Check the state / soldering for the following parts.
ST-BY PART ST-BY PART
CPU Part ST-BY PART
[CN511 : 2pin (3.3V)] [CN511 : 4pin]
[IC101] [Q514]
A normal voltage occurs immediately after the A signal with the same period as the frequency of
Other connected circuits. Other connected circuits.
power is turned on. the power supply is generated.
YES YES
Electrical
Check Power Supply Voltages for DC_5V. NO Check the RESETS signal. NO Check the state / soldering for the following parts.
Check the state / soldering for the following parts.
ST-BY PART CPU Part CPU Part
ST-BY PART
[CN512 : 1pin] [IC101 : 28pin] [IC102]
[CP505]
A normal voltage occurs immediately after the Voltage is output Other connected circuits.
Other connected circuits.
power is turned on. YES
YES
NG Check the state / soldering for the following parts.
Check Power Supply Voltages for A_-12V. NG Check the KEY signal.
Check the state / soldering for the following parts. CPU Part
ST-BY PART CPU Part
ST-BY PART [FPC101, IC101]
[CN512 : 3pin] [IC101 : 60pin]
[IC504] FRONT PART
A normal voltage occurs immediately after the The voltage changes when the POWER button is
Other connected circuits. [FPC502, S505]
pushed.
Mechanical
power is turned on. Other connected circuits.
YES YES
Repair Information
Check Power Supply Voltages for +8VM NO
Check the state / soldering for the following parts.
ST-BY PART
ST-BY PART
[CN512 : 6pin]
[IC502]
A normal voltage occurs immediately after the
Other connected circuits.
power is turned on.
YES
Updating
45
3. VFD is not lit 4. The disc does not load, does not play, or "UNSUPPORTED" is f
NO
indicated on the FL display, etc.
Check the state / soldering for the following parts.
Caution in
servicing
Check Power Supply Voltages for VFD.
ST-BY PART NO
FRONT PART Check the Pickup.
[CN509]
Check Power Supply Voltages for Filament. No abnormalities in "4. Notes on Handling the Replace the mechanical.
FRONT PART
Voltage between [CN501: 1 - 2pin] Laser Pick-Up".
[FL501]
A normal +2.97V ~ 3.63V.
Other connected circuits. YES
YES
Check the KEY signal. NO
Check the state / soldering for the following parts.
Check Power Supply Voltages for VFD. NO CPU Part
Check the state / soldering for the following parts. KEY PCB
FRONT PART [IC101 : 60pin]
ST-BY PART [S506]
Check the voltage for VH. The voltage changes when the PLAY button is
[Q508] Other connected circuits.
[CN501 : 3pin] voltage pushed.
Other connected circuits.
A normal 38V ~ 46V. YES
Electrical
YES
Check the state / soldering for the following parts. NO
Check Power Supply Voltages for VFD. NO CPU Part
Check the state / soldering for the following parts. Repair the abnormal area.
FRONT PART [IC101, IC105, IC104]
DISPLAY PCB
Check the voltage for EK. No other abnormalities in the connected circuit.
[D531]
Voltage of [CN501 : 3 - 1, 2pin] YES
Other connected circuits.
A normal 4.8V ~ 7V.
YES No abnormalities in the wiring. NG
CPU Part
NG Repair or replace the part with the abnormality.
Check Power Supply Voltages for VFD. Check the state / soldering for the following parts. No abnormalities in the wiring or connections
FRONT PART DIR/DAC/VOL PART between [FPC102, CN101, CN102] and the mecha.
Mechanical
YES
Check the voltage for VDD. [IC118]
[FL501 : 37pin (3.3V)] Other connected circuits.
NO
YES Check the state / soldering for the following parts. f
DSP Part Replace the MAIN PCB ASSY with new one.
NO [IC107]
Check the state / soldering for the following parts.
Check the VFD communication signal. YES
CPU Part
FRONT PART
[FPC101, IC101]
[FL501 : 32, 33, 34, 35pin]
Other connected circuits.
Replace the CD mechanism with new one.
Repair Information
YES
Updating
46
5. No audio output from Tuner 6. No audio output from DAB (EK Only)
NO NO
Caution in
servicing
Is the antenna connected normally? Connect the antenna. Is the antenna connected normally? Connect the antenna.
YES YES
NO Check the state / soldering for the following parts. NO Check the state / soldering for the following parts.
Check Power Supply Voltages for Tuner module. Check Power Supply Voltages for Tuner module.
CNT2 PART CNT2 PART
CNT2 PART CNT2 PART
[IC402] [IC402]
[TM501 : 3pin (5V)] [CN505 : 3pin (5V)]
Other connected circuits. Other connected circuits.
YES YES
NO Check the state / soldering for the following parts. NO Check the state / soldering for the following parts.
Electrical
Check control signal for Tuner module. Check control signal for Tuner module.
CPU Part CPU Part
CNT2 PART CNT2 PART
[IC101] [IC102]
[TM501 : 4, 5, 6, 7, 8pin] [CN505 : 4, 5pin]
Other connected circuits. Other connected circuits.
YES YES
Check output signal for Tuner module. NG Check output signal for Tuner module. NG
CNT2 PART CNT2 PART
Change the Tuner module. Change the Tuner module.
[TM501 : 1, 2pin] [CN505 : 1pin]
Analog Audio signal is output. A digital signal is output.
YES YES
Mechanical
Check the state / soldering for the following parts. Check the state / soldering for the following parts.
DIR/DAC/VOL PART DIR/DAC/VOL PART
[IC127, IC124, IC115] [IC127, IC124, IC115]
Other connected circuits. Other connected circuits.
Repair Information
Updating
47
7. No audio output from Bluetooth. 8. No audio output from this unit.
NO Check the state / soldering for the following parts. Check Power Supply Voltages for Audio. NO Check the state / soldering for the following parts.
Caution in
Check Power Supply Voltages for Bluetooth.
servicing
DSP Part AMP ASSY SPK Part
DSP Part
[IC128] [CP706 : 9pin (Hi+B)] [D552]
[FPC103 : 10pin (3.3V)]
Other connected circuits. A voltage near +30V is being generated. Other connected circuits.
YES YES
Check the connection for Bluetooth. NO Check Power Supply Voltages for Audio. NO Check the state / soldering for the following parts.
DSP Part AMP ASSY SPK Part
Repair the abnormal area.
Check the connection between [FPC103] and the [CP706 : 5pin (Hi-B)] [D552]
FFC of the Bluetooth module. A voltage near -30V is being generated. Other connected circuits.
YES YES
Check the state / soldering for the following parts. NO Check Power Supply Voltages for Audio. NO Check the state / soldering for the following parts.
Electrical
DIR/DAC/VOL PART AMP ASSY SPK Part
Repair the abnormal area.
[IC127, IC124, IC115] [CP706 : 5pin (Hi-B)] [D552]
No other abnormalities in the connected circuit. A voltage near -30V is being generated. Other connected circuits.
YES YES
Check the Audio signal. NG Check the state / soldering for the following parts.
Probable causes of problem :
DIR/DAC/VOL PART DIR/DAC/VOL PART
DSP Part [IC107]
[IC115 : 8, 25pin] [IC127, IC124, IC115]
Main PCB
Analog Audio signal is output. Other connected circuits.
Replace the Bluetooth module.
YES
Mechanical
NO
Check the state / soldering for the following parts.
Check the Audio signal.
DIR/DAC/VOL PART
DIR/DAC/VOL PART
[IC102, RLY101, Q104, Q105]
[CP102 : 5, 7pin (AMPIN_L, AMPIN_R)]
MUTE_B+ signal
Analog Audio signal is output.
Other connected circuits.
YES
Repair Information
Area around the SPK Part
Check other connected circuits.
Updating
48
MEASURING METHOD AND WAVEFORMS
1. TEST POINT 2. WAVEFORMS
Connect the GND (-) probe of the oscilloscope to the specified reference voltage points to check the 1. DISC PLAY RF WAVEFORM (EYE-PATTERN)
Caution in
servicing
waveforms. 1.1 CD(TCD784) PLAY
NOTE
Measuring Disc : CD/TCD-784
(It is recommended to use extension wires between the probe and test points.)
• When watching the HF waveform, use the extending wire as short as possible.
• If the HF waveform is unclear due to noise or the eye pattern is indistinguishable, replace the traverse
ASSY after measuring the lop. qRFEQO
• For points q take measurements at the points shown in the diagram below.
1.1. MAIN PCB test point
C349 J115 J113 R419 R407
C350 J111 R417 R410
J116 CN113(RD) CN114(RD) J112 J114
C345 CP102
CN104
CN101
SP+
SP-
SL+
SL-
DGND
LIMIT S/W
Q108
Electrical
R433 Q113 C162
R211
R212
C333
R210
C325
R404
R405
R426
R425
C326
CN102
CLOSE S/W
DGND
OPEN S/W
LOAD-
LOAD+
CN113 CN114 C300
C258
R434
MAIN MUTE
PROTECTOR
GND1 R438
GND2
C296
C332
C331
J151 (8P ETC) (5P EK)
R428
C288
C257
X109
R368 C294
C156
OPT1
DGND
OPT2
DGND
D3V3
SW_MUTE
PROT_V
PWR_ON
PWR_DN
DGND
DAB_SPDIF
DGND
DAB_DA/TU_SDA
DAB_CLK/TU_CLK
TU_INT
TU_RST
TU_SEN
DAB_TU_ON
MUTE_B+
TU_R'
AGND
TU_L'
AUX_L'
AGND
AUX_R'
SW_GND
SW_OUT
AMPIN_GND
AMPIN_L
AMPIN_GND
AMPIN_R
AMPIN_GND
HP_L
H/P_GND
HP_R
R362
C301
C233 R421 R401
R365
R430
C256
R408
R364 R370 R196
38
R198
R361
R454
R453 R437 C163
R197
R195
Q114
Q111
Q107
Q109
R452 R356 C164
R451 C234 C277 C175
R353 R456
Q116
C232 R199
C297
R429
R415
R351 C221 R399
C134 R207
R346 R340
R345 R414
R342
R439
R441
C157
R383 R388
C293
R436
R339
D116
D117 R411
C248 R363 C278 C279 R203
R334
R335
C303
C133
C240
L108
L107
C275 R378
C304
D119
D118
C166
R331
C153
C211
R432
R422
C167
TP112
TP113
TP114
R403
R326
R325
C246 IC115
C143
C227
R413
IC127 R330
J1
C280 C283 R420
X103 16M9344
38
PCM9211 R329 R423
R328 R348 R418 C295 C140
NJW1194A
R327 C139
R400 J124
C145
R440 R442
R354 J128
J101
C141
R352 IC124
PCM5100A
C247
C144 C142 TP110 TP111
C210
C127 R182
C347
9
R350
C274
R374
8 10
R347 R376 C290 C138
J131
C165
10 TP
R341 R409
J1
C226
L105
R336 R396 C169
33 D115
C239
C245
C346
TP
C270 C273 TP106
C220
R366 C126
TP107
TP101
C209
R213
R214
3
R382
R355
R359
R360
10
C215 TP105
R381
FPC102
TP
R332
TP104
C289
C348
C228 C125
R290
R293
R297
TP J1
C219 R181
10 22 IC109
C286
R371
2 W9812G6KH
C212 C131 VC
C214
Q106
C205 R461
C128
R384
C1 13 35
C213
R385
Q101
VCC
C 1
37 6 L106
RLY101 HFD27/012-S C124
C
E
R194
R275 R277
R274 R273
R269 R271
R263 R267
J121
D
C123
R291
A
R186
R185
R184
R183
R462
IN ICT OP ADJ FI
R278
B
R245
75
J139
C
R3
R241
R252
R393
J119
F
C342
D109
R187
R244
AGND1
C154 LD
C285 C282
C250
C155
VR
R294
PD
J1
RCDM41 MAIN
J1
C150
C149
C148
C147
C146
C351
49
F+
27
C338 R246 L114 R280
C249
D110
T-
R231
R220 T+ L116
Q123
C185
F-
L112
7020-08141-040-0V
R127
R307
IC106 L117
AP7361 STEP : MP R261
C184
L118
Pb
10
FPC101
R221
R259
LM7908RTRL
IC117
L1
R317 R312
+3V3_ST
DGND X106 C191 J120
C264 DGND 24MHz
CP101 R229 R230 L123 R236
Mechanical
VFD_3V3
R235
R134 R137
R130 R132
52
D_5V R234
R145
R141
MLC3730
VFD_RST
R149
IC107
R233
C152
C3
DGND1 R240
[[ G ]] VFD_CE
D103
A_-12V C320 VFD_CLK C192 R243
R128
R123
A_+12V IC101
R143
VFD_DA
D105
C7
R151
R147
C186
+8VM R121 KEY1 R289 DGND
C241 C151 R176
C341
FPC105
+3V3_ST TDI
R392
C208 KEY2
R125
R301
R295
R299
R292
35
L111 DGND
CP101
W9812G6KH
RED_LED TMS
IC108
GREEN_LED VDD
R109
R389
R302
R303
R304
R305
LM7808RTRL R112 R217
R163 R114 R115
R223
R225
R264
C194
D127
C195
C223
R171 R170 R172 IC128 C321 C177
R174
R232
R228 R218 TXD
R226 R219 CTS
R224
R222
C110
C_TX
C_RX
DGND
NC
NC
R455
C111
R152
R150
34
C224
D123
D124
C322
R133
C108
R120 R119
RTS
RESET
VDD
4MHz FPC103
R136
C201
R129
C323
R126 R158
R124 R159
R154 R122
R131
R135
D101
R157 R146 R148
D126
C109 IC113
R324
C200
R160
R161
TPS22918
C112
C101
C202
C287
C327
C102
C170
C171
C172
C173
C174
C328
C217
VDD
JTDI
JTDO
JTMS
JTRSTX
DGND
CN112 C218
C284
Detail A
Repair Information
RFEQO q
R413
J1
X103 16M9344
38
C295 C140
C139
J124
C145
C141
C142 TP110 TP111
C144
C127 R182
C347
9
8 10
C290 C138
C165
10 TP
R409
L105
D115 C169
C346
TP
TP106
C126
TP107
TP101
R213
R214
03
TP105
1
TP
TP104
C289
C348
R290
R293
R297
TP J1
10 22 IC109
2 W9812G6KH
Q106
C1 13 35
C 1
37 6 L106
C124
C
R275 R277
R274 R273
R269 R271
R263 R267
J121
C123
R291
FI
R278
R245
J139
R241
R252
J119
R244
J1
Updating
27
49
NOTES ON HANDLING AND REPLACEMENT OF THE LASER PICK-UP
1. Protection of the LD
Solder a part of the LD circuit to short-circuit. After connecting the circuit, remove the soldering form.
Caution in
Precautions when handling the laser CD mechanism
servicing
2. Precautions when handling the laser CD mechanism
• Be careful not to expose the laser pick-up to dust.
• Do not leave the laser pick-up bare. Be sure to cover it.
• If dust adheres on the laser pick-up lens, blow it off with a blower brush.
• Do not apply shock to the laser pick-up.
• Do not watch the light of the laser pick-up.
Electrical
• Be sure that the bench, jig, head of soldering iron (with ceramic) and measuring instruments are well
grounded.
• Workers who handle the laser pick-up must be grounded.
• The finished mechanism (prior to anchoring in the set) should be protected against static electricity
and dust.
The mechanism must be stored where abnormal external force is not applied.
• When carrying the finished mechanism, hold it by the chassis body.
• Do not use or store the mechanism where corrosive gas such as H2S, SO2, NO2 and CI2 or toxic gas
may be generated, or where substances especially organosilicon, cyanide, formalin and phenolic
Mechanical
materials exist. In particular, make sure that these substances which generate toxic gas do not exist in
the set. This may cause the motor not rotating.
Repair Information
Updating
Protective soldering place for laser diode.
50
SPECIAL MODE
Special mode setting button
b No. 1 - 8 : While holding down buttons "A" and "B" simultaneously, insert the AC plug into the wall outlet to turn on the power.
Caution in
servicing
No. Mode Button A Button B Descriptions
The firmware version is shown on the display.
1 Version Display Mode 2 8
(See 1. Version Display Mode)
All segments on the display flash in a 2 second cycle.
2 Display check mode X 5
(See 2. Display check mode)
3 Initialization Mode SOURCE 8 Initialize this unit. (See 3. Initialization Mode)
4 Test mode X SOURCE Servo adjustment. Displaying the adjustment values and laser current. (See 4. Test mode)
4-1 Disc mounting 5 - For executing each CD mode.
Electrical
4-2 Servo check 1/3 - Checks each servo.
4-3 Pickup movement 8 or 9 Moves the pickup to the inner or outer circumference.
4-4 Stop 2 - Stops playback operations and servos and loads the automatic adjustment values.
4-5 All servo on SOURCE - Turns all servos on and performs automatic adjustment.
Displays the following adjustment values.
4-6 Display adjustment values ↑ -
FOCUS BALANCE, FOCUS GAIN, TRACKING BALANCE, TRACKING GAIN, FOCUS OFFSET, TRACKING OFFSET, RFRP
4-7 Displaying the laser current 2 - Indicates the present laser current.
Executes each heat run mode.
5 CD heat Run mode 2 9
Mechanical
(See 5. Heat run mode)
5-1 Normal heat run mode 1/3 - Executes normal heat run mode.
5-2 Chucking mode 2 - Executes chucking mode.
5-3 Error display - - Displays the error code.
Indicates the accumulated laser on time.
6 Accumulated laser on time display mode X 2
(See 6. Accumulated laser on time display mode)
6-1 Resetting the count value 1/3 - Initializes the count value.
Repair Information
Displays the protection occurrence history.
7 Protection history display mode SOURCE 9
(See 7. Protection History Display Mode)
7-1 Resetting the protection history 1/3 - Resetting the protection history.
5 1/3 2
RCD-M41DAB
Updating
X SOURCE 8 9
51
1. Version Display Mode 3. Initialization Mode
1.1. Actions 3.1. Actions
Caution in
servicing
Version information is displayed when the device is started in this mode. Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the
PCB.
1.2. Starting up Initial value of laser current and The accumulated laser on time are not cleared.
While holding down buttons the "2" and "8" buttons simultaneously, insert the AC plug to turn the
power on. 3.2. Operations
then press the "8 or 9" button to display the information in section "1.3." on the display. 1. Press the power operation button to turn off the power, and remove the AC plug from the socket.
2. While holding down buttons the "SOURCE" and "8" buttons simultaneously, insert the AC plug to
1.3. Display Order turn the power on.
q System Version → w Bluetooth Version ····· * This unit can also be initialized by holding down the button "SOURCE" and pressing the power
Unplug the AC plug to cancel this mode. button for 3 seconds or more while on standby.
Electrical
3. "INITIALIZE" is displayed.
* The unit is initialized.
* Unplug the AC plug to cancel this mode.
Mechanical
L1 Ver ********v\\ 3.3. Initialization item
L2 No Items Default
1 SOURCE DISC
\ : Region (E3, E2, EK, CH, JP) 2 TUNER BAND FM (EK only : DAB)
3 TUNER frequency Minimum receive frequency
w Bluetooth Version 4 SDB OFF
5 BASS 0
L1 Bluetooth VER 6 TREBLE 0
L2 7 BLANCE CENTER
**** ** ** **
Repair Information
8 DIMMER 100%
9 VOLUME 5
10 TUNER PRESET ALL 0
11 Unit -/+(TUNER) PRESET - / +
12 Clock 00:00 (flashes, E3 only : AM12:00)
2. Display check mode 13
14
ALARM SOURCE
ALARM ON
DISC
00:00 (flashes, E3 only : AM12:00)
2.1. Operations 15 ALARM OFF 00:00 (flashes, E3 only : AM12:00)
While holding down buttons the "X" and "5" buttons simultaneously, insert the AC plug to turn the 16 SPK OPTIMISE ON
17 CD Auto Play ON
power on.
18 CLOCK MODE Off
Unplug the AC plug to cancel this mode.
19 H/P AMP GAIN Middle
L1 ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ 20 AUTO STANDBY E2/EK : ON, E3/JP/CN : OFF
21 DAB setting (EK Only) initialized
L2 ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ 22 Bluetooth Pairing information None
Updating
23 Bluetooth On/Off setting Off
All segments on the display flash in a 2 second cycle (1 second on, 1 second off).
52
(4. Test mode (
4-3. Pickup movement
4.1. Actions (1) Press the "8 or 9" buttons to move the pickup to the inner or outer circumference.
Caution in
servicing
A mode for starting Servo check, Pickup movement, Stop, All servo on, Adjustment value display, Dis- Release the button to stop the pickup.
playing the laser current and various test modes. (2) You can also stop the pickup by pressing the "8" button. After the inner switch is set to on, the
pickup stops.
(3) Release the button to stop the pickup.
4.2. Starting up
(1) While holding down buttons the "X" and "SOURCE" buttons simultaneously, insert the AC plug to ( 4-4.
turn the power on. Stop
(13 flashes) (1) Press the "2" button to stop the playback operation and servo.
L1 (2) After stopping, the auto adjustment values will be read.
Electrical
(2) Return the slide to the default setting position. (10mm from inner circumference)
Press and hold the "SOURCE" button for five seconds to turn all servos on.
(3) Perform the check by pressing the buttons.
The playback operation starts after automatic adjustment is performed (playback sound is output).
(4) Turn the power back on to cancel this mode.
(13 flashes)
※ Do not operate controls other than the buttons to be used in this mode. (The operations may not
work correctly). L1
L2 @@Tr **:**
( 4-1. Disc mounting @@ : T.No, **:** : time
(1) Press the "5" button to open the tray.
(2) Place the disc in the tray and press the "5" button again to close the tray and start disc chucking.
Mechanical
(3) Return the slide to the default setting position (10mm from inner circumference) and stop it in this
position.
Repair Information
(13 flashes) (13 flashes)
L2 01 LD ON L2 04 Tracking ON
(2) FOCUS ON (disc rotating, tracking off) (5) READ SUB CODE (playback sound output)
zIf there is no disc, the unit retries the operation (13 flashes)
and then stops.
L2 05 @@Tr **:**
(13 flashes)
@@ : T.No, **:** : time
L2 02 Focus ON
(6) Press the "1/3" button while "(5)" is displayed
(3) CLV ON to show the BER(Bit Error Rate) display for two
(13 flashes) seconds.
Updating
(13 flashes)
L2 03 CLV ON
L2 ERR ######
###### : BER
53
(4-6. Adjustment value display (
4-7. Displaying the laser current
4-6.1. Display Order • Press and hold the "2" button for at least 1 second while stopped (CD TEST MODE) to turn the laser
Caution in
servicing
(1) When "SOURCE" button is pressed, the adjustment values are displayed in the following order. ON and measure and display the laser current.
q FOCUS BALANCE → w FOCUS GAIN → e TRACKING BALANCE → r TRACKING GAIN (13 flashes)
→ t FOCUS OFFSET → y TRACKING OFFSET → u RFRP ····· L1 S/C: XXmA/ YYmA
q FOCUS BALANCE t FOCUS OFFSET L2 LASER CURRENT
(13 flashes) (13 flashes) XX : Stored data (stored EEPROM value), YY : Current value
L1 **** L1 ****
• The initial current value is measured after the laser has been on for 3 seconds.
L2 FOCUS BALANCE L2 FOCUS OFFSET • The current value is updated every 3 seconds.
**** : adjustment values **** : adjustment values • The laser on current is measured using A/D conversion. Figures below decimal point are omitted.
• The initial value of the factory, is "50mA" or less.
Electrical
w FOCUS GAIN y TRACKING OFFSET (2) Press the "2" button, to return to the "CD TEST MODE" screen.
(13 flashes) (13 flashes) * Stored data is not erased when this unit is initialized.
L1 **** L1 ****
4-7.1. Overwriting the stored data
L2 FOCUS GAIN L2 TRACKING OFFSET (1) With the laser current displayed, press and hold the "1/3" button for over 5 second to save the cur-
**** : adjustment values **** : adjustment values rent value on EEPROM (overwrite the stored data).
u RFRP (13 flashes)
e TRACKING BALANCE (13 flashes) L1 STORED
(13 flashes)
L1 ****
Mechanical
L2 LASER CURRENT
L1 **** L2 RFRP
L2 TRACKING BALANCE (2) Press the "1/3" button to save the initial value to the EEPROM.
**** : adjustment values
**** : adjustment values (3) After overwriting, the "laser current appears" again.
※ Rewriting is performed upon shipment from the factory and when the mechanism is replaced.
r TRACKING GAIN
(13 flashes)
L1 ****
Repair Information
L2 TRACKING GAIN
**** : adjustment values
(2) Press the "2" button, to return to the "CD TEST MODE" screen.
L2 00 CD TEST MODE
※ If you have not completed the adjustment, the displayed values are not correct.
Updating
54
(5. Heat run mode (
5-2. Chucking mode
(1) Press the "2" button once while stopped after the CD heat run mode starts and TOC reading is com-
5.1. Actions
Caution in
pleted.
servicing
Executes each heat run mode.
(2) Repeat TOC reading → search of first track on disc → OPEN tray → CLOSE tray → TOC reading.
The heat run repetition count is shown in the time display area.
5.2. Starting up (3) An increment is added to the heat run count when the loader is OPEN and the process is completed.
(1) Insert the disc first. 【Display while tray is OPEN】
(2) While holding down buttons the "2" and "9" buttons simultaneously, insert the AC plug to turn (13 lit)
the power on.
(13 lit) L2 CD ****
L2 (**** : heat run repetition count)
CD 11Tr 42:52
(The display is the same as the normal stopped display, except that "1" and "3" are lit) 【Display while tray is CLOSE】
Electrical
(13 lit)
(2) The unit switches to the mode corresponding to the button that is pressed.
(3) If an error occurs, an error display appears and the operation stops immediately. The operation L2 CLOSE
count is retained. See "5.3. Error display"
(4) Pressing the "2" button clears the heat run count. 【Display during TOC reading】
(5) Pressing the "5" button clears the mode and opens the tray. (13 lit)
(6) The mode can also be cleared by pressing the "X" button.
L2 READING
( 5-1. Normal heat run mode
• Press the "1/3" button after the CD heat run mode starts and TOC reading is completed. The heat run
Mechanical
repetition count is 0 at this time.
(1) Play the disc from the first track to the last track.
(2) All tracks are played if the disc being used contains 20 tracks or less. If the disc contains 21 or more
tracks, the unit plays track 1 and then skips to the last track.
(3) When playback of the disc is finished, move the pickup to the inner circumference and open the
tray. An increment is added to the heat run count when the tray is opened.
(4) When the loader OPEN status is detected, close the tray again and start playing the disc from the
first track after TOC has been loaded.
(5) Repeat steps (1) ~ (4).
Repair Information
【Displaying playback】
(13 lit)
L2 CD 01Tr 01:47
(The display is the same as the normal stopped display, except that "1" and "3" are lit)
Updating
55
(5.3. Error display (6. Accumulated laser on time display mode
(13 lit) 6.1. Actions
Caution in
servicing
L2 CD EX-XX • The laser drive time is added and the result is displayed.
• Each count is 10 minutes (truncated if less than 10 minutes).
(EX-XX : Error Code)
• The count value is saved to the EEPROM.
Error Code Description • The accumulated laser on time is displayed in hours.
E1-00 Disc cannot be detected. • The count value is not erased when the unit is initialized (3. Cold start mode).
E1-01 Tracking offset adjustment not possible. • Minimum display specification (also possible when the display time below is exceeded).
E1-02 Focus offset adjustment not possible. • Number of digits retained in EPROM : 4 digits 0xFFFF
E2-00 The focus servo was disabled during playback. • Number of digits displayed : 5 digits
E2-01 The focus servo was disabled during searching. • When 10922 hours are exceeded, the retained data is not updated and the value is fixed as 0xFFFF (the
E2-03 The focus servo was disabled during TOC reading. display is fixed as "10922 hour").
Electrical
E2-06 The focus servo was disabled during manual search.
(1) While holding down buttons the "X" and "2" buttons simultaneously, insert the AC plug to turn the
E2-10 Subcode became unreadable during playback.
power on.
E2-11 Subcode became unreadable during searching.
E2-12 Subcode became unreadable during TOC reading. L1 ***** hour
E2-14 Subcode cannot be read while pausing. L2 LASER ON TIME
E2-15 Subcode cannot be read during manual search.
(**** : Heat run repetition count at the time the error occurred)
E3-00 TOC could not be read within the specified time.
E3-01 PVD/SVD analysis was not be completed within the specified time. (2) Remove the AC plug to exit this mode.
E4-04 Search time out (The search was not completed within the specified time).
Mechanical
E4-05 Decoder bus error (Error in communications with CD decoder).
6.1. Resetting the count value
E5-00 Inner switch is not on.
(1) With the accumulated laser-on time displayed, press and hold the "1/3" button for over 5 second
E6-00 Inner switch is not off.
to reset the count value (overwrite the stored data).
E9-00 A CD u-COM error occurred
E9-01 Error other than above. L1 CLEAR
L2 LASER ON TIME
【Heat run count at the time the error occurred】
(1) Press the "9" button while the error code is displayed.
(2) The display returns to the display in "LASER ON TIME" ("00000 hour" at top) after initialization is
(2) The heat run count is displayed for 5 seconds before returning to the error code display.
Repair Information
completed.
(13 lit)
※ The Count value is reset upon shipment from the factory and when the mechanism is replaced.
L2 CD ****
(**** : Heat run repetition count at the time the error occurred)
【Track number and elapsed time of track at the time the error occurred】
(1) Press the "8" button while the error code is displayed.
(2) The track number and elapsed time of the track at the time the error occurred are displayed for 5
seconds before returning to the error code display.
(13 lit)
L2 05 01Tr **:**
(**** : elapsed time of track at the time the error occurred)
Updating
56
( (
7. Protection History Display Mode 8. Version Display of DAB Module (RCD-M41DAB Only)
(1) While holding down buttons the "SOURCE" and "9" buttons simultaneously, insert the AC plug (1) Insert the AC plug and turn on the power.
Caution in
to turn the power on. (2) Press "TUNER" on the remote control and select "DAB".
servicing
(2) The last backed up protection to be detected is displayed.
L1 DAB
(3) Remove the AC plug to exit this mode.
L2 NO SERVICE
【No detected history】
L1 PROTECTION: (3) Press "DAB/RDS" on the remote control to display the "DAB Menu".
L2 NO PROTECT L1 DAB MENU
•–
L2 AUTO SCAN
【AMP error detected】
Electrical
L1 PROTECTION: (4) Press the cursor button "i" on the remote control 5 times to select "DAB VERSION".
L2 AMP L1 DAB MENU
•–
L2 DAB VERSION
【Power error detected】
L1 PROTECTION: (5) Press "ENTER" on the remote control to display the version of the DAB module.
L2 POWER L1 DAB VERSION
L2 0304/0600
7.1. Resetting the protection history
Mechanical
(1) With the protection history displayed, press and hold the "1/3" button for over 5 seconds to clear
the protection history.
【Cleared display】
L1 PROTECTION:
L2 CLEAR
・Protection history is cleared, even when the Initialization Mode.
Repair Information
Updating
57
h ADJUSTMENT
Adjusting Idling Current
1. Preparation
Caution in
servicing
Prepare a DC voltmeter.
2. Adjustment Procedure
(1) Remove the top cover.
(2) Connect the DC Voltmeter to the test points.
(3) Set this unit as follows.
MASTER VOLUME : "---" (c min.) : turn counterclockwise to the lowest position.
(4) Turn the variable resistance and adjust the voltage of the test point to "2.6mV ± 0.3mV DC".
(5) Adjust the variable resistance of each channel using the same method.
Left ch : CP701 : VR701
Electrical
Right ch : CP702 : VR702
Mechanical
TOP View
Repair Information
Updating
58
UPDATING
PROCEDURE AFTER REPLACING THE PCB.
Caution in
servicing
PROCEDURE AFTER REPLACING THE U-COM, ETC.
Electrical
2. Updating via System u-com (IC101)
3. Updating via Disc (IC109)
4. Updating via DSP (IC109)
Mechanical
Repair Information
Updating
59
PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC.
The procedure after replacing the printed circuit boards is as follows. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows.
(1) Change the resistor for setting the region. Implement the update method when the DIGITAL PCB or network module is replaced.
MAIN PCB Procedure
Caution in
Model Area
servicing
R157 PCB Name Ref. No. Description after Re- Remark
placement
North America (E3) 4K7
DIGITAL IC101 MB9AF344 B SOFTWARE : Main
Europe (E2) 1K8
Europe (EK) 33K DIGITAL IC109 W25Q16JVSSIQ B SOFTWARE : DSP ROM
China (E1C) 8K2 j FRONT FL501
OLD : DISPLAY,FLT 16-ST-103GINK
E DISPLAY
Japan (JP) 15K NEW : DISPLAY VFD CIG25-1607N
See the PCB below. Procedure after Replacement
A : The software has been written. The software is not written at the time of replacement.
(2) Be sure to replace the software with the latest version. B : The software has been written. The software may need to be rewritten by version updates. Check the
version.
Electrical
C : The software has not been written. The software needs to be written after replacement.
C349 J115 J113 R419 R407
C350 J111 R417 R410
J116 CN113(RD) CN114(RD) J112 J114
C345 CP102
CN104
CN101
SP+
SP-
SL+
SL-
DGND
LIMIT S/W
R433 Q113 Q108 C162
R211
R212
C333
R210
C325
R404
R405
R426
R425
C326
CN102
CLOSE S/W
DGND
OPEN S/W
LOAD-
LOAD+
CN113 CN114 C300
C258
R434
MAIN MUTE
PROTECTOR
GND1 R438
GND2
C296
C332
C331
J151 (8P ETC) (5P EK)
D:T
R428
he software has been written. Be sure to replace the software with the latest version.
C288
C257
X109
R368 C294
C156
OPT1
DGND
OPT2
DGND
D3V3
SW_MUTE
PROT_V
PWR_ON
PWR_DN
DGND
DAB_SPDIF
DGND
DAB_DA/TU_SDA
DAB_CLK/TU_CLK
TU_INT
TU_RST
TU_SEN
DAB_TU_ON
MUTE_B+
TU_R'
AGND
TU_L'
AUX_L'
AGND
AUX_R'
SW_GND
SW_OUT
AMPIN_GND
AMPIN_L
AMPIN_GND
AMPIN_R
AMPIN_GND
HP_L
H/P_GND
HP_R
R362
C301
R430
C256
R408
R364 R370 R196
38
R198
R361
R454
R453 R437 C163
R197
R195
Q114
Q111
Q107
Q109
C232 R199
C297
R429
R415
R345 R414
R342
R439
C157
R383 R388
C293
R436
R339
D116
D117 R411
C248 R363 C278 C279 R203
j
R334
R335
C303
C133
C240
L108
L107
C275 R378
C304
D119
D118
C166
R331
C153
C211
R432
R422
C167
TP112
TP113
TP114
R403
R326
R325
C246 IC115
When changing the DISPLAY, make sure it matches the system u-COM [U101] version to change.
C143
C227
R413
IC127 R330
J1
C280 C283 R420
X103 16M9344
38
PCM9211 R329 R423
R328 R348 R418 C295 C140
NJW1194A
R327 C139
R400 J124
C145
R440 R442
R354 J128
J101
C141
C127 R182
C347
9
R350
C274
R374
8 10
R347 R376 C290 C138
J131
C165
10 TP
R341 R409
J1
C226
L105
D115
3
C239
C245
C346
TP
C270 C273 TP106
C220
R366 C126
TP107
TP101
C209
R213
R214
03
R382
R355
R359
R360
C215 TP105
R381
1
FPC102
TP
R332
TP104
C289
C348
C228 C125
R290
R293
R297
TP J1
C219 R181
10 22 IC109
(1) If the system u-COM Version is "Ver 17101933":
C286
R371
2 W9812G6KH
C212 C131 VC
C214
Q106
C205 R461
C128
R384
C1 13 35
C213
R385
Q101
VCC
C 1
37 6 L106
E
R194
R275 R277
R274 R273
R269 R271
R263 R267
J121
D
C123
R291
A
R186
R185
R184
R183
R462
IN ICT OP ADJ FI
R278
B
R245
75
C
R3
R241
R252
R393
J119
F
C342
D109
R187
R244
AGND1
C154 LD
Mechanical
C285 C282
C250
C155
VR R294
PD
J1
RCDM41 MAIN
J1
C150
C149
C148
C147
C146
C351
F+
27
T-
R231
R220 T+ L116
Q123
C185
F-
L112
7020-08141-040-0V
R127
R307
IC106 L117
AP7361 STEP : MP R261
C184
L118
Pb
10
FPC101
R221
L1
R317 R312
+3V3_ST
DGND X106 C191 J120
C264 DGND 24MHz
CP101 R229 R230 L123 VFD_3V3 R236
R235
R134 R137
R130 R132
52
D_5V R234
R145
R141
MLC3730
VFD_RST
R149
IC107
R233
C152
C3
DGND1 R240
[[ G ]] VFD_CE
D103
No procedure required.
VFD_CLK
R128
R123
A_+12V IC101
R143
VFD_DA
D105
C7
R151
R147
FPC105
+3V3_ST TDI
R392
C208 KEY2
R125
R301
R295
R299
R292
35
L111 DGND
CP101
RED_LED TMS
IC108
GREEN_LED VDD
R109
R389
R157
R114 R115
R223
R225
C223
R171 R170 R172 IC128 C321 C177
R174
R232
R228 R218 CTS
R226 R219 RTS
R224
R222
C110
C_TX
C_RX
DGND
NC
NC
R455
C111
R152
R150
34
C224
D123
D124
C322
R133
No procedure required.
C108
R120 R119
RESET
VDD
4MHz FPC103
R136
C201
R129
C323
R126 R158
R124 R159
R154 R122
R131
R135
D101
R157 R146 R148
C109 IC113
R324
C200
R160
R161
TPS22918
C112
C101
C202
C287
C328
C217
VDD
JTDI
JTDO
JTMS
JTRSTX
DGND
Repair Information
CN112 C218
C284
Updating
60
FIRMWARE UPDATE PROCEDURE
1. Items necessary for update
Items necessary for update are as follows.
Caution in
servicing
Offered / not Offered
Update Type Needed Part for Update Requirement Standard Service Equipment
Purchase from D&M Article code Download from SDI
Not offered by D&M
RS-232C cable 9P (Male), Straight X - -
OLD JIG : SPK-581 WRITING KIT
8U-210100S WRITING KIT - 8U- 210100S -
System u-com Update NEW JIG : 8U-310098 DSP UNIT A0
7P FFC Straight - 606050028012P -
FLASHSTA - - - FLASHSTA.EXE
FIRMWARE_Vxx_RCDM41_
DSP Update Provide a writable CD-R/RW disc. - X -
xxxxxxxx.mp3
Electrical
Mechanical
Repair Information
Updating
61
2. Updating via System u-com (IC101)
2.1. Items to Be Prepared 2.3. Installing the Software
Caution in
servicing
(1) Obtain "pcwfm3-v01l07.zip" from SDI. Install the writing software "FLASH MCU Programmer for FM3/FM4" on your computer.
(2) Personal Computer (Be installed "FLASH MCU Programmer for FM0+/FM3/FM4").
(3) RS-232C cable (9P (Male), Straight). (1) Download "pcwfm3-v01l07.zip" from SDI.
A0 (4) 8U-210100S : WRITING KIT (OLD JIG : SPK-581 WRITING KIT, or 8U-310098 DSP UNIT) (2) Double-click "Setup.exe".
606050028012P : 7P FFC (Straight)
Electrical
Computer
Mechanical
(4) Click "Next >".
② Align the switch in the direction of the arrow. ↑Top side is contacts of
5V
flexible card cable.
RESET CNVSS EPM CE DSPBOOT LOW
Using the 7P FFC(Straight).
3.3V HIGH
● is 1PIN side.
Repair Information
→ This side is contacts of
flexible card cable.
8U-210100S : WRITING KIT ● is 1PIN side. (5) Click "Finish".
A0
Updating
62
2.4. Run the FLASH MCU Programmer (5) The following display appears when the firmware update is complete.
(1) Press the power button to turn on the power. Click "OK".
Caution in
servicing
(2) Execute "FLASH MCU Programmer for FM3/FM4" after installing it on your computer.
(1) Double-click FLASH MCU Programmer to launch FLASH MCU Programmer Start.
(7) A
fter updating the firmware, check the version.
(3) Target MCU : Select "MB9AF344L/M/N" See "1. Version Display Mode"
Electrical
Crystal Frequency : Select "4MHz"
Hex File : Select the file to be "Update" RCD_M41(xxxxxx).hex
Set Environment : Select "COM PORT"
Click "Full Operation(D+E+B+P)"
MB9AF156M/N/R
4MHz
XXXXXX_XXXXXX-XX.hex
Mechanical
Repair Information
(4) Press the "Reset" button on the WRITING KIT.
A0 Case of 8U-310098 DSP UNIT : Skip
Updating
63
3. Updating via Disc (IC109) 4. Updating via DSP (IC109)
The latest firmware can be written to a disc for update. 4.1. Preparation
Caution in
servicing
3.1. Support Disc ・Use the Disc created in "3.2. How to create a disc".
(1) Preparation
• Provide a writable CD-R/RW disc. 4.2. Starting up
(1) Press the power button to turn on the power.
3.2. How to create a disc (2) Place the update disc on the tray and close it.
Write the update file to a disc (3) This unit recognizes the update file and then the update starts automatically.
Electrical
・Multi Session : No READING
・File System : ISO9660+Joliet ↓
・Mode : MODE1
・Write speed : 8-16x (match this with the performance of the CD-R) UPGRADE
・Write method : Disc at Once (Finalize(Close)) ↓
UPGRADE
***%
↓
Mechanical
UPGRADE
COMPLETED
When the file data load is completed, "COMPLETED" is displayed and the tray opens automatically.
At this point, make sure to remove the disc from the tray.
Repair Information
(4) After updating the firmware, check the version.
See "1. Version Display Mode"
Updating
64
www.denon.com