Professional Documents
Culture Documents
PDS Lubrizol-6950p
PDS Lubrizol-6950p
PDS Lubrizol-6950p
A multipurpose additive technology for formulating Super Tractor Oil Universal (STOU) fluids.
Provides the top tier STOU technology required for final drive, hydraulic, wet brake,
clutch and transmission performance needed in today's tractors. Can be used in older
engines that do not use aftertreatment devices, and to formulate SAE 10W-30, 15W-30,
15W-40, 20W-30 and 20W-40 viscosity grades.
Balanced friction performance giving precise clutch and brake operations provides a quite responsive tractor for operator
comfort.
Contains several OEM approvals and 'Suitable for Use' claims providing a widely acceptable use across a variety of
agricultural equipment.
Excellent wear protection helps increase uptime and allows the equipment to work harder for longer.
Genuine STOU performance creating the need for only a single oil to avoid misapplication and reduced inventory costs.
Rust and corrosion protection increases hardware and equipment longevity.
API GL-4 S -
Ford M2C159-B S -
ZF TE-ML 06B A -
ZF TE-ML 06C A -
ZF TE-ML 07B A -
Allison C-4 S -
Caterpillar TO-2 S -
ACEA E2 - S
API CE - S
API CF - S
API CF-4 - M
API CG-4 - M
MB-Approval 227.1 - M
MB-Approval 228.1 - M
MAN 271 - S
MIL-L-2104D - S
* All Lubrizol product performance claims are only applicable when the additive package is used with defined base oil(s), viscosity modifier(s) and
other required components to produce the applicable viscosity grade in a properly blended finished fluid.
¹ - Volume treatment rates are approximate as the actual treat rate is dependent on the density of all components in a blend
A - Approved-Formal written approval provided from a governing body such as an OEM, regulatory agency or an industry organization
L - Licensable-Licensable against an active API category
M - Meets-All required testing meets defined specification requirements; however, no formal approval provided, claim is self-certified
S - Suitable for Use (SFU) - Considered suitable for use based on laboratory testing, field testing and engineering judgment (where there is no
regulatory prohibition)
- GIMA M1144 is for STOU fluids only. Lubrizol® 6950P will meet GIMA M1143 but the GIMA M1143 specification can not be claimed
on a STOU as it is for UTTO fluids only.
- ZF TE-ML-06D (Eccom transmission) is a formulation specific approval.
STOU formulated with 13.5%wt Lubrizol 6950P will also deliver the following levels of engine performance:
- API CI-4 and ACEA E7 level of soot control (supported by Mack T-8E)
- ACEA E4-08 and MB228.3 level of wear performance (Supported by OM602 LA and OM646LA - on B05 Fuel
- MB-Approval 228.3 and ACEA E7 level of piston cleanliness (supported by OM441A and OM646LA - on B05 fuel)
Note
- MB-Approval 228.1 primary approval in SAE 15W-40 and MB-Approval 228.1 engine performance in SAE 10W-30
TYPICAL CHARACTERISTICS²
Form Liquid - -
Odor Mild - -
Temperature Recommendations
Unloading
Storage
Blending
Maximum Base Oil Temperature for Mechanical or in-line Mixing 70°C 158°F
Equipment Recommendations
Type of Transfer Line Ball Launched, Insulated,Steam Traced Using 107°C/225°F Steam Max.
Heat Source
Type n/a
Storage Tank
ADDITIONAL RECOMMENDATIONS
* Holding the material in excess of this temperature may cause chemical degradation. Use steam for heating and tracing only
when the material is in motion to avoid localized overheating. Cold Temperature Storage - If product has been stored below its pour
point temperature it should be heated to 21°C/70°F before using.