Professional Documents
Culture Documents
Wired Plus
Wired Plus
How to Use
How can we help?
WARNING: Electrical shock hazard. Disconnect power to the installation area at your circuit breaker
or fuse box before beginning installation. Always use caution when handling electrical wiring.
Installation by a qualified electrician may be required in your area. Refer to your local laws and
building codes before performing electrical work; permits plus professional installation may be
required by law.
Verify that the supply voltage is correct. Connect fixture to a 100~240 VAC 50/60 Hz power
source.
The earth wire must be connected to the light fixture. DO NOT INSTALL if a working earth
connection is not available.
Do not install near combustible or flammable surfaces. Floodlight Cam Wired Plus must be installed
on a wall or eve.
Installation Steps
To install your Floodlight Cam Wired Plus device, follow these steps:
1. Open the Ring app and select Set Up a Device. Then follow the in-app instructions.
2. Scan the QR code found on the front of the manual, or on the back of the camera. This identifies
your Ring device to make setup fast and easy.
You’ll be working with electrical wires during the install process. If you don’t know where the fuse
box is or how to turn off power to the floodlight circuit, we recommend you hire a licensed
electrician.
If you’re mounting to a wall, rotate the camera into position like this:
5. Remove your existing floodlight
1. With power off at the fuse box, remove the existing floodlight from the wall and disconnect the
wires. If there is a bracket attached to the wall, remove that as well.
Push gently on the threaded posts visible on the front of the fixture and pull the bracket free.
If installing on stucco, brick or concrete, mark 2 drill holes using the plastic mounting plate as a
template. Then, use a 6mm masonry drill bit (not included) to drill holes in the wall, and insert the
included anchors.
Install the mounting plate with the two posts level with the ground, or level with the wall if mounting
on an eave or overhang. Ensure the “UP” arrow is pointing upwards for wall mounting, and away
from the area to be monitored for eave and overhang mounting.
Secure the plate with the two mounting screws. Then, push the included rubber plug over the
screws to seal.
Using the Philips head end of the included screwdriver, loosen and remove one of the screws on the
pressing plate and rotate it out of the way. Place the power cable into the channel, but don’t replace
the pressing plate just yet.
Repeat with the neutral wire, sliding it into the bay marked “N” and tightening with the flathead end
of the screwdriver.
Once you’ve confirmed the wires are secure, replace the pressing plate over the power cable and
tighten with the Phillips head end of the screwdriver.
11. Hang it up
Locate the nylon strap on the back of the Floodlight Cam Wired Plus light fixture, and loop the
plastic buckle at the end over the plastic hook on the mounting plate. Make sure the buckle and
hook are secure before releasing the light fixture.
12. Connect the wires from the light fixture
With power still turned off at the fuse box, slide the earth wire into the centre bay on the top of the
terminal block and tighten with the flathead end of the included screwdriver.
Then slide the line wire into the bay on the top of the terminal block marked “L” and tighten with the
flathead end of the screwdriver.
Repeat with the neutral wire, sliding it into the bay marked “N” and tightening with the flathead end
of the screwdriver.
Align the two holes on the light fixture with the threaded posts on the plastic mounting plate. Slide
the light fixture onto the posts and push it firmly into place.
Secure the fixture using two of the coloured hex cap nuts over the ends of the threaded posts.
Remove the reversible bit from the included screwdriver and use the handle to tighten the hex cap
nuts.
14. Restore power at the fuse box
Now that the Floodlight Cam Wired Plus is installed, you can turn power back on at the fuse box. The
lamps will flash once it’s powered on.
Once your Floodlight Cam Wired Plus powers on, follow the instructions to continue with setup in
the app.