Professional Documents
Culture Documents
Manual Installation Steps V5.3 Ed1
Manual Installation Steps V5.3 Ed1
Manual Installation Steps V5.3 Ed1
1/18/2023 2
BACK Panel Description
DC Cord, inner +
Towards line in PC
From PC speaker
1/18/2023
Extension ptt switch to LPA 3
PC Interconnection
USB PORT2
Line In
DRIVER1_CH340.zip
1/18/2023 5
STEP2 – Install Omni Rig
Download & Omni Rig:
Omni rig
Omnirig.zip
1/18/2023 6
STEP3 – Setting Omni Rig
Open Omni Rig
1/18/2023 7
STEP4 – Install HDSDR SOFT REL 2.70 or latest
Extract and Install HDSDR SOFTWARE
HDSDR_install.zip
1/18/2023 8
STEP5 – Install CFGR
Extract and Install CFGSR_V2.6
Install_CFGSR_V2.6.msi.zip
Copied
1/18/2023 9
STEP6 – RUN HDSDR
Open HDSDR
1/18/2023 10
STEP7 – Setting HDSDR Software
Click Sound Card (F5) and follow bellow setting
1/18/2023 11
STEP8 – Setting HDSDR Software
Click Bandwidth (F6) and Set Sampling Rate 44100 I/O
1/18/2023 12
STEP9 – Setting HDSDR Software
Click Option (F7) and Set Follow below Picture
Click Set LO Tune offset
change the Value”0”
1/18/2023 13
STEP10– Setting HDSDR Software
Click Option (F7) and Set Follow below Picture
1/18/2023 14
STEP11 – Setting HDSDR Software
Click Option (F7) and Set Follow below Picture
1/18/2023 15
STEP12 – Setting HDSDR Software
Click Option (F7) and Set Follow below Picture
1/18/2023 16
STEP13– Setting HDSDR Software
Click Option (F7) and Set Follow below Picture
1/18/2023 17
STEP14 – Setting HDSDR Software
Click Option (F7) and Set Follow below Picture
Set “AUTO”
1/18/2023 18
STEP15 – START (F2) HDSDR
Press Start Button
And Press Spacebar for “TX on” and trigger to Matoa Transmit
1/18/2023 19
STEP16 – Setting HDSDR Software on TX active
Press Spacebar for “TX on” and keep on Transmit active..
Press Bandwidth (F6) and follow bellow picture
Setting Bandwidth,
during TX actived mode
1/18/2023 20
STEP17– Setting HDSDR Software on TX actived
Press Spacebar for “TX on” and keep on Transmit active..
Press 0ption (F7) and follow bellow picture
TX actived mode
1/18/2023 21
STEP18 – Setting HDSDR Software on TX active
Press Spacebar for “TX on” and keep on Transmit active..
Press 0ption (F7) and follow bellow picture Calibration for TX
TX actived mode
1/18/2023 22
1/18/2023 23
POWER SDR 2.8.0.163
1/18/2023
OmniRig 24
PC Interconnection
USB PORT2
1/18/2023 26
Latency Analyzer
Install latency
dpclat.zip
1/18/2023 27
MATOA POWER SDR 2.8.0.163 – Hardware Config
1/18/2023 28
MATOA POWER SDR 2.8.0.163 – OMNIRIG
Enable
1/18/2023 29
MATOA POWER SDR 2.8.0.163 - Options
Disable PTT
1/18/2023 30
MATOA POWER SDR 2.8.0.163 – Primary Audio
ASIO4ALL_2_14_English.rar
1/18/2023 31
MATOA POWER SDR 2.8.0.163 – VAC1
Enable VAC 1
Audio Setting
1/18/2023 32
MATOA POWER SDR 2.8.0.163 – DSP Menu
1/18/2023 33
MATOA POWER SDR 2.8.0.163 – RX Image Cal
RX Image Calibration
1/18/2023 34
MATOA POWER SDR 2.8.0.163 – Display Setting
1/18/2023 35
1/18/2023 36