This engineering change order revises wiring diagrams to change the wire gauge specification from 16 AWG to 14 AWG. The current drawings call for 16 AWG wire but operators are using 14 AWG or 16 AWG depending on the conduit assembly, which requires 14 AWG wire for the circuit. This ECO updates the drawings to specify 14 AWG wire for consistency. It revises notes on two wiring diagrams, S-06563-50 and S-06563-59, to replace references to 16 AWG wire with 14 AWG wire.
This engineering change order revises wiring diagrams to change the wire gauge specification from 16 AWG to 14 AWG. The current drawings call for 16 AWG wire but operators are using 14 AWG or 16 AWG depending on the conduit assembly, which requires 14 AWG wire for the circuit. This ECO updates the drawings to specify 14 AWG wire for consistency. It revises notes on two wiring diagrams, S-06563-50 and S-06563-59, to replace references to 16 AWG wire with 14 AWG wire.
This engineering change order revises wiring diagrams to change the wire gauge specification from 16 AWG to 14 AWG. The current drawings call for 16 AWG wire but operators are using 14 AWG or 16 AWG depending on the conduit assembly, which requires 14 AWG wire for the circuit. This ECO updates the drawings to specify 14 AWG wire for consistency. It revises notes on two wiring diagrams, S-06563-50 and S-06563-59, to replace references to 16 AWG wire with 14 AWG wire.
This engineering change order revises wiring diagrams to change the wire gauge specification from 16 AWG to 14 AWG. The current drawings call for 16 AWG wire but operators are using 14 AWG or 16 AWG depending on the conduit assembly, which requires 14 AWG wire for the circuit. This ECO updates the drawings to specify 14 AWG wire for consistency. It revises notes on two wiring diagrams, S-06563-50 and S-06563-59, to replace references to 16 AWG wire with 14 AWG wire.
ECO TYPE ECO CLASSIFICATION MODELS IMPLEMENTATION METHOD
A. EMERGENCY - SHIP NO ENGINES W/O THIS CHANGE NEW RELEASE VHP 16CYL ALL DATE: B. PRIORITY REVISIONS IDENTIFIED PARTS SEE INTENT SECTION C. MUST BE AVAILABLE FOR CHANGES CONFIGURATION RULES NOTIFY CSA D. ROUTINE CHANGES ENGINE OUTLINE OR CONNECTIONS AFFECTS TORSIONAL ANALYSIS E. DOCUMENT ONLY TECH DATA RELEASE SERVICE BULLETIN REQUIRED? F. RESTRICTED RELEASE - PROTOTYPE CE MARK COST REDUCTION: $ INTENT: CURRENTLY IN NOTES OF DRAWING S-SHEET WIRING DIAG. CALLS FOR 16GA WIRE. OPERATORS ARE USING 14 AWG OR 16 AWG BECAUSE THE DIFFERENT CONDUIT ASSEMBLIES FOR THE UNIT CALL 14AWG WIRE SIZES FOR THE CIRCUIT. ALL HARNESSES AND ASSEMBLIES SHOULD USE 14 AWG WIRE FOR THE CIRCUIT. THIS ECO REVISES THE S-SHEET TO CHANGE 16 AWG WIRE TO 14 AWG WIRE IN NOTES. NOTE:
HS/ECCN CODES: (PRC) PART RELATIONSHIP CODES:
"A"=ASSIGNED, "V"=VERIFIED, "R"=REVISED, "N"=N/A (DWI-02-1041) "1"=YES, "2"=NO, "3"=YES IF, N=ENG. OBS. (DWI-02-1032) STOCK DISPOSITION E N R P PRODUCTION SERVICE P PART NUMBER H C SUPERSEDED PART ITEM E E DESCRIPTION R C NEW & REVISED PART(S) S C NUMBER(S) W V C C N USE REWORK SCRAP USE REWORK SCRAP
WIRING DIAGRAM. IGNITION, CSA
1 S-06563-50 X V V 1) CHANGED NOTE 1. “ALL W.E.D. WIRING TO BE #14 AWG RATED 600 VOLTS”. WIRING DIAGRAM. IGNITION, CSA 2 S-06563-59 X V V 1) CHANGED NOTE 1. “ALL W.E.D. WIRING TO BE #14 AWG RATED 600 VOLTS”.
WORK REQUEST: ER62717 APPROVED BY: C. NELSON APPROVED BY: G. PAVON
REQUESTED BY: S. SMITH 10/17/12 APPROVED BY: R. OLSEN APPROVED BY: PREPARED BY: A. GARNICA 08/19/15 APPROVED BY: D. OURADNIK APPROVED BY: CHECKED BY: J. KOLBACH 08/21/15 APPROVED BY: T. SINTKOWSKI ISSUED BY: Form 0135-A 12-2-2009