The document provides specifications for tightening cylinder head bolts on a C7 industrial engine. It lists the following steps:
1. Tighten bolts 1-14 in sequence to 300 Nm and then loosen to 0 Nm.
2. Retighten bolts 1-14 in sequence to 130 Nm twice.
3. Turn bolts 1-14 an additional 90 degrees.
It also provides instructions for installing cup plugs, injector sleeves, seals, and plugs, including applying specific types of thread locking compounds.
The document provides specifications for tightening cylinder head bolts on a C7 industrial engine. It lists the following steps:
1. Tighten bolts 1-14 in sequence to 300 Nm and then loosen to 0 Nm.
2. Retighten bolts 1-14 in sequence to 130 Nm twice.
3. Turn bolts 1-14 an additional 90 degrees.
It also provides instructions for installing cup plugs, injector sleeves, seals, and plugs, including applying specific types of thread locking compounds.
The document provides specifications for tightening cylinder head bolts on a C7 industrial engine. It lists the following steps:
1. Tighten bolts 1-14 in sequence to 300 Nm and then loosen to 0 Nm.
2. Retighten bolts 1-14 in sequence to 130 Nm twice.
3. Turn bolts 1-14 an additional 90 degrees.
It also provides instructions for installing cup plugs, injector sleeves, seals, and plugs, including applying specific types of thread locking compounds.
Item Qt Part Specification Description y – 14 142-7289 Cylinder Use the following procedure to tighten the cylinder Head Fastener Gp head bolts: – 6 8T-7950 Bolt 1. Tighten bolt 1 through bolt 14 in a numerical sequence to 300 ± 15 N·m (220 ± 11 lb ft). 2. Loosen bolt 1 through bolt 14 to 0 N·m (0 lb ft). 3. Tighten bolt 1 through bolt 14 in a numerical sequence to 130 ± 15 N·m (95 ± 11 lb ft). 4. Again, tighten bolt 1 through bolt 14 in a numerical sequence to 130 ± 15 N·m (95 ± 11 lb ft). 5. Turn bolt 1 through bolt 14 in a numerical sequence to an additional angle of 90 degrees (1/4 turn). Before assembly, lubricate the threads and the bearing surfaces of bolt 15 through bolt 20 with 4C- 5599 Anti-Seize Compound . 6. Tighten bolt 15 through bolt 20 in a numerical sequence to C 6 8M-5860 Cup Plug Before assembly, apply Loctite #120540 to the bores. Installation depth of the cup plug is 1.25 ± 0.25 mm (0.049 ± 0.010 inch). D 6 227-1200 Injector Length for applying green Loctite 620 on the injector Sleeve sleeve is 4.0 mm (0.16 inch). 21 6 310-7257 O-Ring Apply clean engine oil. Seals 22 6 310-7255 O-Ring Seal Table 1
Right side view of engine
Specification for 219-5849 Cylinder Head Gp
Item Q Part Specification Description t 23 2 319-6234 Plug As Torque to 184 ± 18 N·m (136 ± 13 lb ft). G – – Height of new cylinder head is 158.00 ± 0.15 mm (6.220 ± 0.006 inch). K 4 8M-5860 Cup Plug Before assembly, apply Loctite #120540 to the bores. Installation depth of the cup plug is 1.25 ± 0.25 mm (0.049 ± 0.010 inch). L 2 4F-5695 Cup Plug Before assembly, apply Loctite #120540 to the bores. Installation depth of the cup plug 1.25 ± 0.25 mm (0.049 ± 0.010 inch). 24 6 307-2671 Plug As Torque to 16.0 ± 1.5 N·m (140 ± 13 lb in). N 2 8M-5860 Cup Plug Before assembly, apply Loctite #120540 to the bores. Installation depth of the cup plug is 1.25 ± 0.25 mm (0.049 ± 0.010 inch). Table 2