Professional Documents
Culture Documents
Redox Titration
Redox Titration
Redox Titration
Analytical titrations using redox reactions were introduced shortly after the development of acid–base titrimetry. The earliest
Redox titration took advantage of the oxidizing power of chlorine. In 1787, Claude Berthollet introduced a method for the
quantitative analysis of chlorine water (a mixture of Cl2, HCl, and HOCl) based on its ability to oxidize indigo, a dye that is
colorless in its oxidized state. In 1814, Joseph Gay-Lussac developed a similar method for determining chlorine in bleaching
powder. In both methods the end point is a change in color. Before the equivalence point the solution is colorless due to the
oxidation of indigo. After the equivalence point, however, unreacted indigo imparts a permanent color to the solution.
The number of redox titrimetric methods increased in the mid-1800s with the introduction of MnO4–, Cr2O72–, and I2 as
oxidizing titrants, and of Fe2+ and S2O32– as reducing titrants. Even with the availability of these new titrants, redox titrimetry
was slow to develop due to the lack of suitable indicators. A titrant can serve as its own indicator if its oxidized and reduced
forms differ significantly in color. For example, the intensely purple MnO4– ion serves as its own indicator since its reduced
form, Mn2+, is almost colorless. Other titrants require a separate indicator. The first such indicator, diphenylamine, was
introduced in the 1920s. Other redox indicators soon followed, increasing the applicability of redox titrimetry.
where Aox is the titrand’s oxidized form, and Bred is the titrant’s reduced form. The reaction’s potential, Erxn, is the difference
between the reduction potentials for each half-reaction.
Erxn = EB − EA (2)
ox / Bred ox / Ared
After each addition of titrant the reaction between the titrand and the titrant reaches a state of equilibrium. Because the
potential at equilibrium is zero, the titrand’s and the titrant’s reduction potentials are identical.
EB = EA (3)
ox / Bred ox / Ared
This is an important observation because we can use either half-reaction to monitor the titration’s progress.
Before the equivalence point the titration mixture consists of appreciable quantities of the titrand’s oxidized and reduced
forms. The concentration of unreacted titrant, however, is very small. The potential, therefore, is easier to calculate if we use
the Nernst equation for the titrand’s half-reaction
RT [ Ared ]
o
Erxn = E − ln (4)
Aox / A
red nF [ Aox ]
Although the Nernst equation is written in terms of the half-reaction’s standard state potential, a matrix-dependent formal
potential often is used in its place. See Appendix 13 for the standard state potentials and formal potentials for selected half-
reactions.
After the equivalence point it is easier to calculate the potential using the Nernst equation for the titrant’s half-reaction.
RT [ Bred ]
o
Erxn = E − ln (5)
Box / B
red nF [ Box ]
4/23/2021 1 https://chem.libretexts.org/@go/page/22130
Let’s calculate the titration curve for the titration of 50.0 mL of 0.100 M Fe2+ with 0.100 M Ce4+ in a matrix of 1 M HClO4.
The reaction in this case is
2+ 4+ 3+ 3+
Fe (aq) + Ce (aq) ⇌ Ce (aq) + Fe (aq) (9.15)
In 1 M HClO4, the formal potential for the reduction of Fe3+ to Fe2+ is +0.767 V, and the formal potential for the reduction
of Ce4+ to Ce3+ is +1.70 V.
Because the equilibrium constant for reaction 9.15 is very large—it is approximately 6 × 1015—we may assume that the
analyte and titrant react completely.
Step 1
Calculate the volume of titrant needed to reach the equivalence point.
The first task is to calculate the volume of Ce4+ needed to reach the titration’s equivalence point. From the reaction’s
stoichiometry we know that
2+ 4+
moles Fe = moles Ce (6)
Solving for the volume of Ce4+ gives the equivalence point volume as
MFe VFe (0.100 M)(50.0 mL)
Veq = VCe = = = 50.0 mL (8)
MCe (0.100 M)
Step 2:
alculate the potential before the equivalence point by determining the concentrations of the titrand’s oxidized and reduced
forms, and using the Nernst equation for the titrand’s reduction half-reaction.
Before the equivalence point, the concentration of unreacted Fe2+ and the concentration of Fe3+ are easy to calculate. For this
reason we find the potential using the Nernst equation for the Fe3+/Fe2+ half-reaction.
2+ 2+
RT [F e ] [F e ]
o
E =E 3+ 2+
− log = +0.767V − 0.05916 log (9.16)
Fe /Fe 3+ 3+
nF [F e ] [F e ]
For example, the concentrations of Fe2+ and Fe3+ after adding 10.0 mL of titrant are
2+ 4+
initial moles Fe − moles Ce added MFe VFe − MCe VCe
2+
[ Fe ] = = (9)
total volume VFe + VCe
4+
moles C e added MCe VCe
3+
[F e ] = = (11)
total volume VFe + VCe
Step 3:
Calculate the potential after the equivalence point by determining the concentrations of the titrant’s oxidized and reduced
forms, and using the Nernst equation for the titrant’s reduction half-reaction.
After the equivalence point, the concentration of Ce3+ and the concentration of excess Ce4+ are easy to calculate. For this
reason we find the potential using the Nernst equation for the Ce4+/Ce3+ half-reaction.
4/23/2021 2 https://chem.libretexts.org/@go/page/22130
3+ 3+
RT [C e ] [C e ]
o
E =E 4+ 3+
− log = +1.70 V − 0.05916 log (9.17)
Ce /Ce
nF [C e4+ ] [C e4+ ]
For example, after adding 60.0 mL of titrant, the concentrations of Ce3+ and Ce4+ are
2+
initial moles Fe MFe VFe
3+
[ Ce ] = = (14)
total volume VFe + VCe
4+ 2+
4+
moles Ce added − initial moles Fe MCe VCe − MFe VFe
[ Ce ] = = (16)
total volume VFe + VCe
Step 4
Calculate the potential at the equivalence point.
At the titration’s equivalence point, the potential, Eeq, in equation 9.16 and equation 9.17 are identical. Adding the equations
together to gives
2+ 3+
[ Fe ][C e ]
o o
2 Eeq = E 3+ 2+
+E 4+ 3+
− 0.05916 log (19)
Fe /Fe Ce /Ce 3+ 4+
[F e ][C e ]
Because [Fe2+] = [Ce4+] and [Ce3+] = [Fe3+] at the equivalence point, the log term has a value of zero and the equivalence
point’s potential is
o o
E 3+ 2+
+E 4+ 3+
Fe /Fe Ce /Ce 0.767 V + 1.70 V
Eeq = = = 1.23 V (20)
2 2
Additional results for this titration curve are shown in Table 9.15 and Figure 9.36.
Table 9.15: Data for the Titration of 50.0 mL of 0.100 M Fe2+ with 0.100 M Ce4+
Volume of Ce4+ (mL) E (V) Volume Ce4+ (mL) E (V)
4/23/2021 3 https://chem.libretexts.org/@go/page/22130
Figure 9.36 Titration curve for the titration of 50.0 mL of 0.100 M Fe2+ with 0.100 M Ce4+. The red points correspond to the
data in Table 9.15. The blue line shows the complete titration curve.
Exercise 1
Calculate the titration curve for the titration of 50.0 mL of 0.0500 M Sn2+ with 0.100 M Tl3+. Both the titrand and the
titrant are 1.0 M in HCl. The titration reaction is
2+ 3+ 4+ +
Sn (aq) + Tl (aq) → Sn (aq) + Tl (aq) (21)
This is the same example that we used in developing the calculations for a redox titration curve. You can review the results
of that calculation in Table 9.15 and Figure 9.36.
We begin by calculating the titration’s equivalence point volume, which, as we determined earlier, is 50.0 mL. Next, we draw
our axes, placing the potential, E, on the y-axis and the titrant’s volume on the x-axis. To indicate the equivalence point’s
volume, we draw a vertical line corresponding to 50.0 mL of Ce4+. Figure 9.37a shows the result of the first step in our sketch.
Before the equivalence point, the potential is determined by a redox buffer of Fe2+ and Fe3+. Although we can easily calculate
the potential using the Nernst equation, we can avoid this calculation by making a simple assumption. You may recall from
Chapter 6 that a redox buffer operates over a range of potentials that extends approximately ±(0.05916/n) unit on either side of
EoFe3+/Fe2+. The potential is at the buffer’s lower limit
o
E =E 3+ 2+
− 0.05916 (22)
Fe /Fe
when the concentration of Fe2+ is 10× greater than that of Fe3+. The buffer reaches its upper potential
o
E =E 3+ 2+
+ 0.05916 (23)
Fe /Fe
when the concentration of Fe2+ is 10× smaller than that of Fe3+. The redox buffer spans a range of volumes from
approximately 10% of the equivalence point volume to approximately 90% of the equivalence point volume.
Figure 9.37b shows the second step in our sketch. First, we superimpose a ladder diagram for Fe2+ on the y-axis, using its
EoFe3+/Fe2+ value of 0.767 V and including the buffer’s range of potentials. Next, we add points representing the pH at 10% of
the equivalence point volume (a potential of 0.708 V at 5.0 mL) and at 90% of the equivalence point volume (a potential of
0.826 V at 45.0 mL).
4/23/2021 4 https://chem.libretexts.org/@go/page/22130
We used a similar approach when sketching the acid–base titration curve for the
titration of acetic acid with NaOH.
The third step in sketching our titration curve is to add two points after the equivalence point. Here the potential is controlled
by a redox buffer of Ce3+ and Ce4+. The redox buffer is at its lower limit of E = EoCe4+/Ce3+ – 0.05916 when the titrant reaches
110% of the equivalence point volume and the potential is EoCe4+/Ce3+ when the volume of Ce4+ is 2×Veq.
Figure 9.37c shows the third step in our sketch. First, we add a ladder diagram for Ce4+, including its buffer range, using its
EoCe4+/Ce3+ value of 1.70 V. Next, we add points representing the potential at 110% of Veq (a value of 1.66 V at 55.0 mL) and at
200% of Veq (a value of 1.70 V at 100.0 mL).
We used a similar approach when sketching the complexation titration curve for the
titration of Mg2+ with EDTA.
Next, we draw a straight line through each pair of points, extending the line through the vertical line representing the
equivalence point’s volume (Figure 9.37d). Finally, we complete our sketch by drawing a smooth curve that connects the three
straight-line segments (Figure 9.37e). A comparison of our sketch to the exact titration curve (Figure 9.37f) shows that they
are in close agreement.
Figure 9.37: Illustrations showing the steps in sketching an approximate titration curve for the titration of 50.0 mL of 0.100 M
Fe2+ with 0.100 M Ce4+ in 1 M HClO4: (a) locating the equivalence point volume; (b) plotting two points before the
4/23/2021 5 https://chem.libretexts.org/@go/page/22130
equivalence point; (c) plotting two points after the equivalence point; (d) preliminary approximation of titration curve using
straight-lines; (e) final approximation of titration curve using a smooth curve; (f) comparison of approximate titration curve
(solid black line) and exact titration curve (dashed red line). See the text for additional details.
Exercise 2
Sketch the titration curve for the titration of 50.0 mL of 0.0500 M Sn4+ with 0.100 M Tl+. Both the titrand and the titrant
are 1.0 M in HCl. The titration reaction is
2+ 3+ 4+ +
Sn (aq) + Tl (aq) → Sn (aq) + Tl (aq) (24)
Compare your sketch to your calculated titration curve from Practice Exercise 9.17.
Click here to review your answer to this exercise.
Example 1
Derive a general equation for the equivalence point’s potential when titrating Fe2+ with MnO4–.
2+ − + 3+ 2+
5 Fe (aq) + MnO (aq) + 8 H (aq) → 5 Fe (aq) + Mn (aq) + 4 H2 O (25)
4
− + − 2+
MnO 4 (aq) + 8 H (aq) + 5 e → Mn (aq) + 4 H2 O(l) (27)
2+
0.05916 [ Mn ]
o
E =E −
− log (29)
2+
MnO /Mn 5 − + 8
4
[ MnO ][H ]
4
Before adding these two equations together we must multiply the second equation by 5 so that we can combine the log
terms; thus
2+ 2+
[F e ][Mn ]
o o
6E = E 3+ 2+
+ 5E −
− 0.05916 log (30)
2+ −
Fe /Fe MnO /Mn 3+ + 8
4 [F e ][ MnO ][ H ]
4
4/23/2021 6 https://chem.libretexts.org/@go/page/22130
2+ −
[ Fe ] = 5 × [ MnO 4 ] (31)
3+ 2+
[ Fe ] = 5 × [ Mn ] (32)
Substituting these equalities into the previous equation and rearranging gives us a general equation for the potential at the
equivalence point.
− 2+
5[ MnO ][Mn ]
o o 4
6 Eeq = E 3+ 2+
+ 5E −
− 0.05916 log (33)
2+ −
Fe /Fe MnO /Mn 2+ + 8
4 5[Mn ][ MnO ][ H ]
4
o o
E 3+ 2+
+ 5E −
2+
Fe /Fe MnO /Mn 0.05916 1
4
Eeq = − log (34)
+ 8
6 6 [H ]
o o
E 3+ 2+
+ 5E −
2+
Fe /Fe MnO /Mn 0.05916 × 8
4 +
Eeq = + log[ H ] (35)
6 6
o o
E 3+ 2+
+ 5E −
2+
Fe /Fe MnO /Mn
4
Eeq = − 0.07888pH (36)
6
Our equation for the equivalence point has two terms. The first term is a weighted average of the titrand’s and the titrant’s
standard state potentials, in which the weighting factors are the number of electrons in their respective half-reactions.
(Instead of standard state potentials, you can use formal potentials.) The second term shows that Eeq for this titration is pH-
dependent. At a pH of 1 (in H2SO4), for example, the equivalence point has a potential of
0.768 + 5 × 1.51
Eeq = − 0.07888 × 1 = 1.31 V (37)
6
Figure 9.38 shows a typical titration curve for titration of Fe2+ with MnO4–. Note that the titration’s equivalence point is
asymmetrical.
Figure 9.38: Titration curve for the titration of 50.0 mL of 0.100 M Fe2+ with 0.0200 M MnO4– at a fixed pH of 1 (using
H2SO4). The equivalence point is shown by the red dot.
Exercise 3
Derive a general equation for the equivalence point’s potential for the titration of U4+ with Ce4+. The unbalanced reaction is
4+ 4+ 2+ 3+
Ce (aq) + U (aq) → UO (aq) + Ce (aq) (38)
2
4/23/2021 7 https://chem.libretexts.org/@go/page/22130
Three types of indicators are used to signal a redox titration’s end point. The oxidized and reduced forms of some titrants, such
as MnO4–, have different colors. A solution of MnO4– is intensely purple. In an acidic solution, however, permanganate’s
reduced form, Mn2+, is nearly colorless. When using MnO4– as a titrant, the titrand’s solution remains colorless until the
equivalence point. The first drop of excess MnO4– produces a permanent tinge of purple, signaling the end point.
Some indicators form a colored compound with a specific oxidized or reduced form of the titrant or the titrand. Starch, for
example, forms a dark blue complex with I3–. We can use this distinct color to signal the presence of excess I3– as a titrant—a
change in color from colorless to blue—or the completion of a reaction consuming I3– as the titrand—a change in color from
blue to colorless. Another example of a specific indicator is thiocyanate, SCN–, which forms a soluble red-colored complex of
Fe(SCN)2+ with Fe3+.
The most important class of indicators are substances that do not participate in the redox titration, but whose oxidized and
reduced forms differ in color. When we add a redox indicator to the titrand, the indicator imparts a color that depends on the
solution’s potential. As the solution’s potential changes with the addition of titrant, the indicator changes oxidation state and
changes color, signaling the end point.
To understand the relationship between potential and an indicator’s color, consider its reduction half-reaction
−
Inox + ne ⇌ Inred (39)
where Inox and Inred are, respectively, the indicator’s oxidized and reduced forms.
For simplicity, Inox and Inred are shown without specific charges. Because there is a
change in oxidation state, Inox and Inred cannot both be neutral.
The Nernst equation for this half-reaction is
0.05916 [Inred ]
o
E =E − log (40)
Inox /Inre d
n [Inox ]
As shown in Figure 9.39, if we assume that the indicator’s color changes from that of Inox to that of Inred when the ratio
[Inred]/[Inox] changes from 0.1 to 10, then the end point occurs when the solution’s potential is within the range
0.05916
o
E =E ± (41)
Inox /Inre d
n
Figure 9.39 Diagram showing the relationship between E and an indicator’s color. The ladder diagram defines potentials
where Inred and Inox are the predominate species. The indicator changes color when E is within the range
4/23/2021 8 https://chem.libretexts.org/@go/page/22130
E = EoInox/Inred ± 0.05916/n
A partial list of redox indicators is shown in Table 9.16. Examples of appropriate and inappropriate indicators for the titration
of Fe2+ with Ce4+ are shown in Figure 9.40.
Table 9.16 Selected Examples of Redox Indicators
Indicator Color of Inox Color of Inred EoInox/Inred
tris(5-nitro-1,10-
pale blue red-violet 1.25
phenanthroline)iron
Figure 9.40: Titration curve for the titration of 50.0 mL of 0.100 M Fe2+ with 0.100 M Ce4+. The end point transitions for the
indicators diphenylamine sulfonic acid and ferroin are superimposed on the titration curve. Because the transition for ferroin
is too small to see on the scale of the x-axis—it requires only 1–2 drops of titrant—the color change is expanded to the right.
4/23/2021 9 https://chem.libretexts.org/@go/page/22130
potentiometry is found in Chapter 11. Other methods for locating the titration’s end point include thermometric titrations and
spectrophotometric titrations.
The best way to appreciate the theoretical and practical details discussed in this section is to carefully examine a typical
redox titrimetric method. Although each method is unique, the following description of the determination of the total
chlorine residual in water provides an instructive example of a typical procedure. The description here is based on Method
4500-Cl B as published in Standard Methods for the Examination of Water and Wastewater, 20th Ed., American Public
Health Association: Washington, D. C., 1998.
4/23/2021 10 https://chem.libretexts.org/@go/page/22130
Figure 9.41 Endpoint for the determination of the total chlorine residual. (a) Acidifying the sample and adding KI forms a
brown solution of I3–. (b) Titrating with Na2S2O3 converts I3– to I– with the solution fading to a pale yellow color as we
approach the end point. (c) Adding starch forms the deep purple starch–I3– complex. (d) As the titration continues, the end
point is a sharp transition from a purple to a colorless solution. The change in color from (c) to (d) typically takes 1–2 drops of
titrant.
provides the electrons for reducing the titrand. In the Walden reductor the column is filled with granular Ag metal. The
solution containing the titrand is acidified with HCl and passed through the column where the oxidation of silver
− −
Ag(s) + Cl (aq) → AgCl(s) + e (43)
provides the necessary electrons for reducing the titrand. Table 9.17 provides a summary of several applications of reduction
columns.
Table 9.17 Examples of Reactions For Reducing a Titrand’s Oxidation State Using a Reduction Column
Oxidized Titrand Walden Reductor Jones Reductor
4/23/2021 11 https://chem.libretexts.org/@go/page/22130
Oxidized Titrand Walden Reductor Jones Reductor
Several reagents are commonly used as auxiliary oxidizing agents, including ammonium peroxydisulfate, (NH4)2S2O8, and
hydrogen peroxide, H2O2. Peroxydisulfate is a powerful oxidizing agent
2− − 2−
S2 O (aq) + 2 e → 2SO (aq) (44)
8 4
capable of oxidizing Mn2+ to MnO4–, Cr3+ to Cr2O72–, and Ce3+ to Ce4+. Excess peroxydisulfate is easily destroyed by briefly
boiling the solution. The reduction of hydrogen peroxide in acidic solution
+ −
H2 O2 (aq) + 2 H (aq) + 2 e → 2 H2 O(l) (45)
provides another method for oxidizing a titrand. Excess H2O2 is destroyed by briefly boiling the solution.
4+ − 3+
Ce (aq) + e ⇌ Ce (aq) (47)
Solutions of Ce4+ usually are prepared from the primary standard cerium ammonium nitrate, Ce(NO3)4•2NH4NO3, in 1 M
H2SO4. When prepared using a reagent grade material, such as Ce(OH)4, the solution is standardized against a primary
standard reducing agent such as Na2C2O4 or Fe2+ (prepared using iron wire) using ferroin as an indicator. Despite its
availability as a primary standard and its ease of preparation, Ce4+ is not as frequently used as MnO4– because it is more
expensive.
Note
The standardization reactions are
4+ 2+ 3+ 3+
Ce (aq) + F e (aq) → C e (aq) + F e (aq) (48)
4+ 3+ +
2C e (aq) + H2 C2 O4 (aq) → 2C e (aq) + 2C O2 (g) + 2 H (aq) (49)
Solutions of MnO4– are prepared from KMnO4, which is not available as a primary standard. Aqueous solutions of
permanganate are thermodynamically unstable due to its ability to oxidize water.
− −
4 MnO (aq) + 2 H2 O(l) ⇌ 4MnO2 (s) + 3 O2 (g) + 4OH (aq) (50)
4
This reaction is catalyzed by the presence of MnO2, Mn2+, heat, light, and the presence of acids and bases. A moderately stable
solution of permanganate can be prepared by boiling it for an hour and filtering through a sintered glass filter to remove any
solid MnO2 that precipitates. Standardization is accomplished against a primary standard reducing agent such as Na2C2O4 or
Fe2+ (prepared using iron wire), with the pink color of excess MnO4– signaling the end point. A solution of MnO4– prepared in
this fashion is stable for 1–2 weeks, although the standardization should be rechecked periodically.
Note
The standardization reactions are
4/23/2021 12 https://chem.libretexts.org/@go/page/22130
− 2+ + 2+ 3+
MnO 4 (aq) + 5F e (aq) + 8 H (aq) → Mn (aq) + 5F e (aq) + 4 H2 O(l) (51)
− + 2+
2 MnO 4 (aq) + 5 H2 C2 O4 (aq) + 6 H (aq) → 2Mn (aq) + 10C O2 (g) + 8 H2 O(l) (52)
Potassium dichromate is a relatively strong oxidizing agent whose principal advantages are its availability as a primary
standard and the long term stability of its solutions. It is not, however, as strong an oxidizing agent as MnO4– or Ce4+, which
makes it less useful when the titrand is a weak reducing agent. Its reduction half-reaction is
2− + − 3+
C r2 O (aq) + 14 H (aq) + 6 e ⇌ 2C r (aq) + 7 H2 O(l) (53)
7
Although a solution of Cr2O72– is orange and a solution of Cr3+ is green, neither color is intense enough to serve as a useful
indicator. Diphenylamine sulfonic acid, whose oxidized form is red-violet and reduced form is colorless, gives a very distinct
end point signal with Cr2O72–.
Iodine is another important oxidizing titrant. Because it is a weaker oxidizing agent than MnO4–, Ce4+, and Cr2O72–, it is
useful only when the titrand is a stronger reducing agent. This apparent limitation, however, makes I2 a more selective titrant
for the analysis of a strong reducing agent in the presence of a weaker reducing agent. The reduction half-reaction for I2 is
− −
I2 (aq) + 2 e ⇌ 2I (aq) (54)
Because iodine is not very soluble in water, solutions are prepared by adding an excess of I–. The complexation reaction
− −
I2 (aq) + I (aq) ⇌ I (aq) (55)
3
increases the solubility of I2 by forming the more soluble triiodide ion, I3–. Even though iodine is present as I3– instead of I2,
the number of electrons in the reduction half-reaction is unaffected.
− − −
I (aq) + 2 e ⇌ 3I (aq) (56)
3
Solutions of I3– are normally standardized against Na2S2O3 using starch as a specific indicator for I3–.
Note
The standardization reaction is
− 2− − 2−
I (aq) + 2 S2 O (aq) → 3 I (aq) + 2 S4 O (aq) (57)
3 3 6
An oxidizing titrant such as MnO4–, Ce4+, Cr2O72–, and I3–, is used when the titrand is in a reduced state. If the titrand is in an
oxidized state, we can first reduce it with an auxiliary reducing agent and then complete the titration using an oxidizing titrant.
Alternatively, we can titrate it using a reducing titrant. Iodide is a relatively strong reducing agent that could serve as a
reducing titrant except that a solution of I– is susceptible to the air-oxidation of I– to I3–.
− − −
3I (aq) ⇌ I (aq) + 2 e (58)
3
Note
A freshly prepared solution of KI is clear, but after a few days it may show a faint yellow coloring due to the presence of
I3–.
Instead, adding an excess of KI reduces the titrand, releasing a stoichiometric amount of I3–. The amount of I3– produced is
then determined by a back titration using thiosulfate, S2O32–, as a reducing titrant.
2− 2− −
2 S2 O (aq) ⇌ 2 S4 O (aq) + 2 e (59)
3 6
Solutions of S2O32– are prepared using Na2S2O3•5H2O, and must be standardized before use. Standardization is accomplished
by dissolving a carefully weighed portion of the primary standard KIO3 in an acidic solution containing an excess of KI. The
reaction between IO3– and I–
− − + −
IO (aq) + 8 I (aq) + 6 H (aq) → 3 I (aq) + 3 H2 O(l) (60)
3 3
liberates a stoichiometric amount of I3–. By titrating this I3– with thiosulfate, using starch as a visual indicator, we can
determine the concentration of S2O32– in the titrant.
4/23/2021 13 https://chem.libretexts.org/@go/page/22130
Note
The standardization titration is
− 2− − 2−
I (aq) + 2 S2 O (aq) → 3 I (aq) + 2 S4 O (aq) (61)
3 3 6
which is the same reaction used to standardize solutions of I3−. This approach to standardizing solutions of S2O32−. is
similar to the determination of the total chlorine residual outlined in Representative Method 9.3.
Although thiosulfate is one of the few reducing titrants that is not readily oxidized by contact with air, it is subject to a slow
decomposition to bisulfite and elemental sulfur. If used over a period of several weeks, a solution of thiosulfate should be
restandardized periodically. Several forms of bacteria are able to metabolize thiosulfate, which also can lead to a change in its
concentration. This problem can be minimized by adding a preservative such as HgI2 to the solution.
Another useful reducing titrant is ferrous ammonium sulfate, Fe(NH4)2(SO4)2•6H2O, in which iron is present in the +2
oxidation state. A solution of Fe2+ is susceptible to air-oxidation, but when prepared in 0.5 M H2SO4 it remains stable for as
long as a month. Periodic restandardization with K2Cr2O7 is advisable. The titrant can be used to directly titrate the titrand by
oxidizing Fe2+ to Fe3+. Alternatively, ferrous ammonium sulfate is added to the titrand in excess and the quantity of Fe3+
produced determined by back titrating with a standard solution of Ce4+ or Cr2O72–.
Inorganic Analysis
One of the most important applications of redox titrimetry is evaluating the chlorination of public water supplies.
Representative Method 9.3, for example, describes an approach for determining the total chlorine residual by using the
oxidizing power of chlorine to oxidize I– to I3–. The amount of I3– is determined by back titrating with S2O32–.
The efficiency of chlorination depends on the form of the chlorinating species. There are two contributions to the total chlorine
residual—the free chlorine residual and the combined chlorine residual. The free chlorine residual includes forms of chlorine
that are available for disinfecting the water supply. Examples of species contributing to the free chlorine residual include Cl2,
HOCl and OCl–. The combined chlorine residual includes those species in which chlorine is in its reduced form and, therefore,
no longer capable of providing disinfection. Species contributing to the combined chlorine residual are NH2Cl, NHCl2 and
NCl3.
When a sample of iodide-free chlorinated water is mixed with an excess of the indicator N,N-diethyl-p-phenylenediamine
(DPD), the free chlorine oxidizes a stoichiometric portion of DPD to its red-colored form. The oxidized DPD is then back
titrated to its colorless form using ferrous ammonium sulfate as the titrant. The volume of titrant is proportional to the free
residual chlorine.
Having determined the free chlorine residual in the water sample, a small amount of KI is added, catalyzing the reduction
monochloramine, NH2Cl, and oxidizing a portion of the DPD back to its red-colored form. Titrating the oxidized DPD with
ferrous ammonium sulfate yields the amount of NH2Cl in the sample. The amount of dichloramine and trichloramine are
determined in a similar fashion.
The methods described above for determining the total, free, or combined chlorine residual also are used to establish a water
supply’s chlorine demand. Chlorine demand is defined as the quantity of chlorine needed to completely react with any
substance that can be oxidized by chlorine, while also maintaining the desired chlorine residual. It is determined by adding
progressively greater amounts of chlorine to a set of samples drawn from the water supply and determining the total, free, or
combined chlorine residual.
Another important example of redox titrimetry, which finds applications in both public health and environmental analyses is
the determination of dissolved oxygen. In natural waters, such as lakes and rivers, the level of dissolved O2 is important for
two reasons: it is the most readily available oxidant for the biological oxidation of inorganic and organic pollutants; and it is
necessary for the support of aquatic life. In a wastewater treatment plant dissolved O2 is essential for the aerobic oxidation of
waste materials. If the concentration of dissolved O2 falls below a critical value, aerobic bacteria are replaced by anaerobic
bacteria, and the oxidation of organic waste produces undesirable gases, such as CH4 and H2S.
One standard method for determining the dissolved O2 content of natural waters and wastewaters is the Winkler method. A
sample of water is collected without exposing it to the atmosphere, which might change the concentration of dissolved O2. The
4/23/2021 14 https://chem.libretexts.org/@go/page/22130
sample is first treated with a solution of MnSO4, and then with a solution of NaOH and KI. Under these alkaline conditions the
dissolved oxygen oxidizes Mn2+ to MnO2.
2+ −
2Mn (aq) + 4OH (aq) + O2 (g) → 2MnO2 (s) + 2 H2 O(l) (62)
After the reaction is complete, the solution is acidified with H2SO4. Under the now acidic conditions I– is oxidized to I3– by
MnO2.
− + 2+ −
MnO2 (s) + 3 I (aq) + 4 H (aq) → Mn +I (aq) + 2 H2 O(l) (63)
3
The amount of I3– formed is determined by titrating with S2O32– using starch as an indicator. The Winkler method is subject to
a variety of interferences, and several modifications to the original procedure have been proposed. For example, NO2–
interferes because it can reduce I3– to I– under acidic conditions. This interference is eliminated by adding sodium azide,
NaN3, reducing NO2– to N2. Other reducing agents, such as Fe2+, are eliminated by pretreating the sample with KMnO4, and
destroying the excess permanganate with K2C2O4.
Another important example of redox titrimetry is the determination of water in nonaqueous solvents. The titrant for this
analysis is known as the Karl Fischer reagent and consists of a mixture of iodine, sulfur dioxide, pyridine, and methanol.
Because the concentration of pyridine is sufficiently large, I2 and SO2 react with pyridine (py) to form the complexes py•I2 and
py•SO2. When added to a sample containing water, I2 is reduced to I– and SO2 is oxidized to SO3.
Methanol is included to prevent the further reaction of py•SO3 with water. The titration’s end point is signaled when the
solution changes from the product’s yellow color to the brown color of the Karl Fischer reagent.
Organic Analysis
Redox titrimetry also is used for the analysis of organic analytes. One important example is the determination of the chemical
oxygen demand (COD) of natural waters and wastewaters. The COD provides a measure of the quantity of oxygen necessary
to completely oxidize all the organic matter in a sample to CO2 and H2O. Because no attempt is made to correct for organic
matter that can not be decomposed biologically, or for slow decomposition kinetics, the COD always overestimates a sample’s
true oxygen demand. The determination of COD is particularly important in managing industrial wastewater treatment
facilities where it is used to monitor the release of organic-rich wastes into municipal sewer systems or the environment.
A sample’s COD is determined by refluxing it in the presence of excess K2Cr2O7, which serves as the oxidizing agent. The
solution is acidified with H2SO4 using Ag2SO4 to catalyze the oxidation of low molecular weight fatty acids. Mercuric sulfate,
HgSO4, is added to complex any chloride that is present, preventing the precipitation of the Ag+ catalyst as AgCl. Under these
conditions, the efficiency for oxidizing organic matter is 95–100%. After refluxing for two hours, the solution is cooled to
room temperature and the excess Cr2O72– is determined by back titrating using ferrous ammonium sulfate as the titrant and
ferroin as the indicator. Because it is difficult to completely remove all traces of organic matter from the reagents, a blank
titration must be performed. The difference in the amount of ferrous ammonium sulfate needed to titrate the sample and the
blank is proportional to the COD.
Iodine has been used as an oxidizing titrant for a number of compounds of pharmaceutical interest. Earlier we noted that the
reaction of S2O32– with I3– produces the tetrathionate ion, S4O62–. The tetrathionate ion is actually a dimer consisting of two
thiosulfate ions connected through a disulfide (–S–S–) linkage. In the same fashion, I3– can be used to titrate mercaptans of the
general formula RSH, forming the dimer RSSR as a product. The amino acid cysteine also can be titrated with I3–. The product
of this titration is cystine, which is a dimer of cysteine. Triiodide also can be used for the analysis of ascorbic acid (vitamin C)
by oxidizing the enediol functional group to an alpha diketone
and for the analysis of reducing sugars, such as glucose, by oxidizing the aldehyde functional group to a carboxylate ion in a
basic solution.
4/23/2021 15 https://chem.libretexts.org/@go/page/22130
An organic compound containing a hydroxyl, a carbonyl, or an amine functional group adjacent to an hydoxyl or a carbonyl
group can be oxidized using metaperiodate, IO4–, as an oxidizing titrant.
− − − −
IO (aq) + H2 O(l) + 2 e ⇌ IO (aq) + 2OH (aq) (65)
4 3
A two-electron oxidation cleaves the C–C bond between the two functional groups, with hydroxyl groups being oxidized to
aldehydes or ketones, carbonyl functional groups being oxidized to carboxylic acids, and amines being oxidized to an
aldehyde and an amine (ammonia if a primary amine). The analysis is conducted by adding a known excess of IO4– to the
solution containing the analyte, and allowing the oxidation to take place for approximately one hour at room temperature.
When the oxidation is complete, an excess of KI is added, which converts any unreacted IO4– to IO3– and I3–.
− − − − −
IO (aq) + 3 I (aq) + H2 O(l) → IO (aq) + I (aq) + 2OH (aq) (66)
4 3 3
The I3– is then determined by titrating with S2O32– using starch as an indicator.
Quantitative Calculations
The quantitative relationship between the titrand and the titrant is determined by the stoichiometry of the titration reaction. If
you are unsure of the balanced reaction, you can deduce the stoichiometry by remembering that the electrons in a redox
reaction must be conserved.
Example 9.11
The amount of Fe in a 0.4891-g sample of an ore was determined by titrating with K2Cr2O7. After dissolving the sample in
HCl, the iron was brought into the +2 oxidation state using a Jones reductor. Titration to the diphenylamine sulfonic acid
end point required 36.92 mL of 0.02153 M K2Cr2O7. Report the ore’s iron content as %w/w Fe2O3.
(Although we can deduce the stoichiometry between the titrant and the titrand without balancing the titration reaction, the
balanced reaction
2+ + 3+ + 3+
K2 C r2 O7 (aq) + 6F e (aq) + 14 H (aq) → 2C r (aq) + 2 K (aq) + 6F e (aq) + 7 H2 O(l) (67)
does provide useful information. For example, the presence of H+ reminds us that the reaction fs feasibility is pH-
dependent.)
Solution
Because we have not been provided with the titration reaction, let’s use a conservation of electrons to deduce the
stoichiometry. During the titration the analyte is oxidized from Fe2+ to Fe3+, and the titrant is reduced from Cr2O72– to Cr3+.
Oxidizing Fe2+ to Fe3+ requires only a single electron. Reducing Cr2O72–, in which each chromium is in the +6 oxidation
state, to Cr3+ requires three electrons per chromium, for a total of six electrons. A conservation of electrons for the titration,
therefore, requires that each mole of K2Cr2O7 reacts with six moles of Fe2+.
The moles of K2Cr2O7 used in reaching the end point is
−4
(0.02153 M K2 C r2 O7 ) × (0.03692 L K2 C r2 O7 ) = 7.949 × 10 mol K2 C r2 O7 (68)
−3 2+
1 mol Fe2 O3 159.69 g Fe2 O3
4.769 × 10 mol F e × × = 0.3808 g F e2 O3 (70)
2+
2 mol Fe mol Fe2 O3
4/23/2021 16 https://chem.libretexts.org/@go/page/22130
0.3808 g Fe2 O3
× 100 = 77.86% w/w F e2 O3 (71)
0.4891 g sample
As shown in the following two examples, we can easily extend this approach to an analysis that requires an indirect analysis or
a back titration.
Example 9.12
A 25.00-mL sample of a liquid bleach was diluted to 1000 mL in a volumetric flask. A 25-mL portion of the diluted sample
was transferred by pipet into an Erlenmeyer flask containing an excess of KI, reducing the OCl– to Cl–, and producing I3–.
The liberated I3– was determined by titrating with 0.09892 M Na2S2O3, requiring 8.96 mL to reach the starch indicator end
point. Report the %w/v NaOCl in the sample of bleach.
Solution
To determine the stoichiometry between the analyte, NaOCl, and the titrant, Na2S2O3, we need to consider both the reaction
between OCl– and I–, and the titration of I3– with Na2S2O3.
First, in reducing OCl– to Cl–, the oxidation state of chlorine changes from +1 to –1, requiring two electrons. The oxidation
of three I– to form I3– releases two electrons as the oxidation state of each iodine changes from –1 in I– to –⅓ in I3–. A
conservation of electrons, therefore, requires that each mole of OCl– produces one mole of I3–.
Second, in the titration reaction, I3–. is reduced to I– and S2O32– is oxidized to S4O62–. Reducing I3– to 3I– requires two
elections as each iodine changes from an oxidation state of –⅓ to –1. In oxidizing S2O32– to S4O62–, each sulfur changes its
oxidation state from +2 to +2.5, releasing one electron for each S2O32–. A conservation of electrons, therefore, requires that
each mole of I3– reacts with two moles of S2O32–.
Finally, because each mole of OCl– produces one mole of I3–, and each mole of I3– reacts with two moles of S2O32–, we
know that every mole of NaOCl in the sample ultimately results in the consumption of two moles of Na2S2O3.
The balanced reactions for this analysis are:
− − + − −
OC l (aq) + 3 I (aq) + 2 H (aq) → I (aq) + C l (aq) + H2 O(l) (72)
3
− 2− 2− −
I (aq) + 2 S2 O (aq) → S4 O (aq) + 3 I (aq) (73)
3 3 6
Because the bleach was diluted by a factor of 40 (25 mL to 1000 mL), the concentration of NaOCl in the bleach is 5.28%
(w/v).
Example 9.13
The amount of ascorbic acid, C6H8O6, in orange juice was determined by oxidizing the ascorbic acid to dehydroascorbic
acid, C6H6O6, with a known amount of I3–, and back titrating the excess I3– with Na2S2O3. A 5.00-mL sample of filtered
4/23/2021 17 https://chem.libretexts.org/@go/page/22130
orange juice was treated with 50.00 mL of 0.01023 M I3–. After the oxidation was complete, 13.82 mL of 0.07203 M
Na2S2O3 was needed to reach the starch indicator end point. Report the concentration ascorbic acid in mg/100 mL.
Solution
For a back titration we need to determine the stoichiometry between I3– and the analyte, C6H8O6, and between I3– and the
titrant, Na2S2O3. The later is easy because we know from Example 9.12 that each mole of I3– reacts with two moles of
Na2S2O3.
The balanced reactions for this analysis are:
− − +
C6 H8 O6 (aq) + I (aq) → 3 I (aq) + C6 H6 O6 (aq) + 2 H (aq) (77)
3
− 2− 2− −
I (aq) + 2 S2 O (aq) → S4 O (aq) + 3 I (aq) (78)
3 3 6
In oxidizing ascorbic acid to dehydroascorbic acid, the oxidation state of carbon changes from +⅔ in C6H8O6 to +1 in
C6H6O6. Each carbon releases ⅓ of an electron, or a total of two electrons per ascorbic acid. As we learned in Example
9.12, reducing I3– requires two electrons; thus, a conservation of electrons requires that each mole of ascorbic acid
consumes one mole of I3–.
The total moles of I3– reacting with C6H8O6 and with Na2S2O3 is
− − −4 −
(0.01023 M I ) × (0.05000 L I ) = 5.115 × 10 mol I (79)
3 3 3
Subtracting the moles of I3– reacting with Na2S2O3 from the total moles of I3– gives the moles reacting with ascorbic acid.
−4 − −4 − −5 −
5.115 × 10 mol I − 4.977 × 10 mol I = 1.38 × 10 mol I (81)
3 3 3
There are 2.43 mg of ascorbic acid in the 5.00-mL sample, or 48.6 mg per 100 mL of orange juice.
4/23/2021 18 https://chem.libretexts.org/@go/page/22130
Figure 9.42 Titration curve for the titration of 50.0 mL of 0.0125 M Sn2+ and 0.0250 M Fe2+ with 0.050 M Ce4+. Both the
titrand and the titrant are 1M in HCl.
Contributors
David Harvey (DePauw University)
4/23/2021 19 https://chem.libretexts.org/@go/page/22130