Professional Documents
Culture Documents
Em48av M System Ind Digital
Em48av M System Ind Digital
INSTRUCTION MANUAL
n PACKAGE INCLUDES:
Bargraph indicating alarm.......................................... (1)
Retaining Clip
n MODEL NO.
Check that model No. described on the specification label is
exactly what you ordered.
n INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation and connection. • The acrylic front cover and scaleplate can be removed when
you remove the nameplates.
n WIRING
• Do not install cables (power supply, input and output) close
to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises
Bezel are present. Do not install them in the same duct.
n AND ....
• The unit is designed to function as soon as power is supplied,
however, a warm up for 10 minutes is required for satisfying
complete performance described in the data sheet.
EM-9312 Rev.8 P. 1 / 5
48AV
COMPONENT IDENTIFICATION
Ventilation Slits
at the Top and Bottom
(15 cm min.)
Scale Plate
Acrylic Cover
Nameplate
■ VERTICAL MOUNTING
■HORIZONTAL MOUNTING
*
EM-9312 Rev.8 P. 2 / 5
48AV
INSTALLATION mm (inch)
n EXTERNAL DIMENSIONS
1
2
3
4
5
138.1 (5.44)
138.1 (5.44)
144 (5.67)
139 (5.47)
144 (5.67)
6
7
8
9
10
11
12
36 (1.42) 9 (.35) 135 (5.31) 20 (.79) 36 (1.42) 7.5 (.30) 9.4 (.37)
41 (1.61) 164 (6.46)
n PANEL CUTOUT
■ VERTICAL MOUNTING Panel thickness: 1.6 – 5.5 mm ■ HORIZONTAL MOUNTING Panel thickness: 1.6 – 5.5 mm
+1 +1
139.5 –0 139.5 –0
+1
139.5 –0
+1
L = (38 x n) –0 164 min.
(n: number of units)
L
+1
L = 38 x (n–1) + 36.5 –0
(n: number of units)
Note 1. A bezel is required between units for high-density
mounting. Note 1. A bezel is required between units for high-density
Note 2. Observe at the minimum of 5 cm above mounting.
and below the units for heat dissipation.
TERMINAL CONNECTIONS
Refer to the connection diagrams below.
■ 48AV-2 ■48AV-4
+ 1 3 Hc + 1 3 Hc, HHc
INPUT INPUT
– 2 4 Ha HH OUTPUT – 2 4 HHa HH OUTPUT
HI OUTPUT
5 Hb 5 HHb
8 La 6 Ha
9 Lb LL OUTPUT 7 La
10 Lc 8 LLa
LO OUTPUT
11 U(+) 9 LLb LL OUTPUT
POWER
12 V(–) 10 LC, LLC
11 U(+)
■Relay Protection POWER
•AC Powered •DC Powered 12 V(–)
Inductive Inductive
Load (Coil) Load (Coil)
EM-9312 Rev.8 P. 3 / 5
48AV
ADJUSTMENT PROCEDURE
SETPOINT CHANGE
SETPOINT CHANGE
SETPOINT CHANGE
SETPOINT CHANGE
SETPOINT CHANGE
SETPOINT CHANGE
DISPLAY
OFF M • SET • COMPLETED
DISPLAY
ON M • SET • COMPLETED
Remark 1: HH, H, L and LL setpoints are stored in the memory even the power is lost during operation.
Remark 2: HH and LL Setpoint Adj. are deleted with model 48AV-2.
EM-9312 Rev.8 P. 4 / 5
48AV
CALIBRATION PROCEDURE
This unit is calibrated at the factory to meet the ordered speci-
fications, therefore you usually do not need any calibration.
For matching the indication to a receiving instrument or in
case of regular calibration, adjust the output as explained
in the following.
MAINTENANCE
Regular checking procedure is explained below:
n CHECKING
Warm up the unit for at least 10 minutes. Apply 0%, 25%,
50%, 75% and 100% input signal. Check that the output
indication for the respective input signal remains within
accuracy described in the data sheet. When the output is out
of tolerance, recalibrate the unit according to the "CALIBRA-
TION PROCEDURE" explained earlier.
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: info@m-system.co.jp
EM-9312 Rev.8 P. 5 / 5