Professional Documents
Culture Documents
ILCE-7RM4 Service Manual L2
ILCE-7RM4 Service Manual L2
ILCE-7RM4/7RM4A
SERVICE MANUAL US Model
Canadian Model
Ver. 1.2 2021.03 AEP Model
LEVEL 2 UK Model
Russian Model
E Model
Indian Model
Note:
Chinese Model
Be sure to keep your PC used for service and
checking of this unit always updated with the
Korea Model
latest version of your anti-virus software.
In case a virus affected unit was found during Photo: ILCE-7RM4
Africa Model
service, contact your Service Headquarters. Tourist Model
Conditions of Use:
(1) Please use this information only for the purpose of performing repair, maintenance and/or configuration services of the Sony products (hereinafter the “Repair services”) under the
service agreement entered into with the Sony group company (hereinafter the “Service agreement”). Using this information for any purpose other than the purpose described foregoing
is forbidden.
(2) Only the Authorized Servicer’s officers, employees or subcontractors (including their officers and employees) whose duties justify a need-to-know and who have agreed to hold
confidential this information (collectively hereinafter the “Permitted users”) are permitted to access and use this information. To disclose or disseminate to any person other than the
Permitted users is forbidden.
(3) Destroy or erase any and all portion of this information promptly in an irrecoverable and secure fashion after achieving the purpose described in Section (1) above.
(4) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author.
(Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.)
(5) Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address:
somk-gcs-tissnexim-adm@jp.sony.com
(6) In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information.
Revision of Information:
This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before using it.
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
SPECIFICATIONS
Camera [Exposure control] [Recording media] WW587956 (see name plate on the
Metering method: 1 200-zone SLOT 1/SLOT 2: Slot for SD cards bottom of camera) (ILCE-7RM4)
[System] evaluative metering (UHS-I and UHS-II compatible) WW778752 (see name plate on the
Camera Type: Metering Range: –3 EV to +20 EV (at bottom of camera) (ILCE-7RM4A)
Interchangeable Lens Digital Camera ISO 100 equivalent with F2.0 lens) [Input/output terminals] Supported format:
Lens: Sony E-mount lens ISO sensitivity (Recommended USB Type-C terminal: IEEE 802.11 b/g/n
exposure index): SuperSpeed USB (USB 3.2 Gen 1) Frequency band: 2.4 GHz
[Image sensor] Still images: ISO 100 to ISO 32 000 Multi/Micro USB Terminal*: Security: WEP/WPA-PSK/WPA2-PSK
Image format: 35 mm full frame (Extended ISO: Minimum ISO 50, Hi-Speed USB (USB 2.0) Connection method:
(35.7 mm × 23.8 mm), CMOS image maximum ISO 102 400) * Supports Micro USB compatible Wi-Fi Protected Setup™ (WPS)/
sensor Movies: ISO 100 to ISO 32 000 devices. Manual
Effective pixel number of camera: equivalent HDMI: HDMI type D micro jack Access method: Infrastructure mode
Approx. 61 000 000 pixels ¯ (Microphone) terminal:
Total pixel number of camera: [Shutter] 3.5 mm Stereo mini jack [NFC]
Approx. 62 500 000 pixels Type: Electronically-controlled, (Headphones) terminal: Tag type: NFC Forum Type 3 Tag
vertical-traverse, focal-plane type 3.5 mm Stereo mini jack compliant
[SteadyShot] Speed range: (Flash sync) terminal
In-camera sensor shift image Still images: 1/8 000 second to [Bluetooth communications]
stabilization system 30 seconds, BULB [General] Bluetooth standard Ver. 4.1
Movies: 1/8 000 second to Rated input: 7.2 V , 3.7 W Frequency band: 2.4 GHz
[Auto focus system] 1/4 second Operating temperature:
Detection system: Phase detection 1080 60i-compatible devices 0 to 40°C (32 to 104°F) Battery charger BC-QZ1
system/Contrast detection system (1080 50i-compatible devices): Storage temperature: Rated input:
Sensitivity Range: –3 EV to +20 EV (at up to 1/60 (1/50) second in AUTO –20 to 55°C (–4 to 131°F) 100 - 240 V , 50/60 Hz, 0.38 A
ISO 100 equivalent, F2.0) mode (up to 1/30 (1/25) second in Dimensions (W/H/D) (Approx.): Rated output: 8.4 V , 1.6 A
Auto slow shutter mode) 128.9 × 96.4 × 77.5 mm
[Electronic viewfinder] Flash sync speed: 1/250 second 128.9 × 96.4 × 67.3 mm
(when using a flash manufactured
Rechargeable battery pack
Type: 1.3 cm (0.5 type) Electronic (from grip to monitor)
Viewfinder by Sony) 5 1/8 × 3 7/8 × 3 1/8 in. NP-FZ100
Total number of dots: 5 760 000 dots 5 1/8 × 3 7/8 × 2 3/4 in. Rated voltage: 7.2 V
Magnification: Approx. 0.78× with [Recording format] (from grip to monitor)
50 mm lens at infinity, –1 m–1 File format: JPEG (DCF Ver. 2.0, Exif Mass (Approx.): Design and specifications are subject
Eye Point: Approx. 23 mm from the Ver. 2.31, MPF Baseline) compliant, 665 g (1 lb 7.5 oz) (including to change without notice.
eyepiece and approx. 18.5 mm RAW (Sony ARW 2.3 format) battery pack, SD card)
from the eyepiece frame at –1 m–1 Movie (XAVC S format):
Diopter Adjustment: MPEG-4 AVC/H.264 XAVC S ver.1.0 [Wireless LAN]
–4.0 m–1 to +3.0 m–1 format compliant WW716189 (see name plate on the
Video: MPEG-4 AVC/H.264 bottom of camera) (ILCE-7RM4)
[Monitor] (ILCE-7RM4) Audio: LPCM 2ch (48 kHz 16 bit) WW447485 (see name plate on the
7.5 cm (3.0 type) TFT drive, touch Movie (AVCHD format): bottom of camera) (ILCE-7RM4A)
panel AVCHD format Ver. 2.0 compatible Supported format:
Total number of dots: 1 440 000 dots Video: MPEG-4 AVC/H.264 IEEE 802.11 a/b/g/n/ac
Audio: Dolby Digital 2ch, equipped Frequency band: 2.4 GHz/5 GHz
[Monitor] (ILCE-7RM4A) with Dolby Digital Stereo Creator Security: WEP/WPA-PSK/WPA2-PSK
7.52 cm (3.0 type) TFT drive, touch • Manufactured under license from Connection method:
panel Dolby Laboratories. Wi-Fi Protected Setup™ (WPS)/
Total number of dots: 2 359 296 dots Manual
Access method: Infrastructure mode
• Abbreviation
AF : Africa model
CH : Chinese model
CND : Canadian model
IND : Indian model
JE : Tourist model
KR : Korea model
RU : Russian model
2
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Caution ⌞ᝅ
Danger of explosion if battery is incorrectly replaced. 如果电池更换不当会有爆炸危险。
Replace only with the same or equivalent type. 只能用同样类型或等效类型的电池来更换。
Dispose of used batteries according to the instructions. 务必按照说明处置用完的电池。
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered UNLEADED SOLDER
connections. Check the entire board surface for solder splashes
This unit uses unleaded solder.
and bridges.
Boards requiring use of unleaded solder are printed with the lead
2. Check the interboard wiring to ensure that no wires are “pinched”
free mark (LF) indicating the solder contains no lead.
or contact high-wattage resistors.
(Caution: Some printed circuit boards may not come printed with
3. Look for unauthorized replacement parts, particularly transistors,
the lead free mark due to their particular size.)
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs : LEAD FREE MARK
of deterioration. Point them out to the customer and recommend Be careful to the following points to solder or unsolder.
their replacement.
5. Check the B+ voltage to see it is at the values specified. • Set the soldering iron tip temperature to 350°C approximately.
6. Flexible Circuit Board Repairing If cannot control temperature, solder/unsolder at high temperature
• Keep the temperature of the soldering iron around 350°C dur- for a short time.
ing repairing. Caution: The printed pattern (copper foil) may peel away if the
• Do not touch the soldering iron on the same conductor of the heated tip is applied for too long, so be careful!
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone
• Be careful not to apply force on the conductor when soldering to flow) than ordinary solder so use caution not to let
or unsoldering. solder bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder
and those for leaded solder so they are managed separately.
Mixing unleaded solder and leaded solder will cause detachment
phenomenon.
3
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE Update of MAC Address and Device Address
SY-1098 BOARD (ILCE-7RM4)/SY-1118 When a board that contains Wi-Fi and Bluetooth has been replaced
or when replacing a board that contains the main IC (CPU), the IC’s
BOARD (ILCE-7RM4A)
unique number (MAC address and device address) must be reloaded.
Perform the following procedure to reload the IC’s unique number
Destination Data (MAC address and device address).
When you replace to the repairing board, the written destination data
of repairing board also might be changed to original setting. Note: Perform the following operations after all work has been done.
Start the Adjust manual in the Adjust station and execute the “Des-
tination Data Write”. 1. Download the latest-version Adjust manual.
2. Install the downloaded Adjust manual.
3. Start the Adjust manual, and execute “Wi-Fi & Bluetooth Setting”
Restore Data
on the ADJUST tab.
When you replace to the repairing board, get the data from the 4. Perform the following operations for the unit to initialize.
former one. [MENU] button → [ ] → [Reset Network Set.] → [Enter]
Start the Adjust manual in the Adjust station and perform “RESTORE 5. Perform the following operations for the unit to display MAC
DATA” to get the data. address.
The data getting for this model is as follows. [MENU] button → [ ] → [Wi-Fi Settings] → [Display Wi-Fi
• Product ID & USB Serial Data Info.]
• WB Adjustment Data 6. Confirm that the displayed MAC address has been updated.
• AORI Adjustment Data 7. Perform the following operations for the unit to display device
• Eyepiece Detection Adjustment Data address.
• Imager DRA Data [MENU] button → [ ] → [Bluetooth Settings] → [Disp Device
Address]
USB Serial No. and Product ID 8. Confirm that the displayed device address has been updated.
The unit is shipped after an ID (USB Serial No.) unique to each unit
and an ID (Product ID) unique to each model have been written. Applicable parts
These IDs have not been written in a new board for service, and • SY-1098 BOARD, COMPLETE (SERVICE) (ILCE-7RM4)
therefore they must be entered after the board replacement. • SY-1118 BOARD, COMPLETE (SERVICE) (ILCE-7RM4A)
After the board has been replaced with a board for service, start the
Note: The LOAD AND WRITE function in ADJUSTMENT DATA
Adjust manual in the Adjust station and execute the “Product ID & BACKUP on the DATA tab in the Adjust manual overwrites all data
USB Serial No. Input” and enter these IDs. of the unit.
Therefore, the MAC address and device address updated during the
Note: A newly entered Product ID is not always equal to the ID before above procedure is also overwritten.
board replacement. If the new ID differs from the previous ID, it may
cause a difference from the ID registered by the customer.
After the replacement and repair, the MAC address and device ad-
dress are changed, and thus the re-setting for connection devices is
Imager DRA Data required. Accordingly, download the Flyer of WLAN Reset (Flyer
• When the imager data is extracted from the set before the SY board of WLAN Reset_9834752[][].pdf) and print out it, and attach it to
replacement, extract the imager data from the set before the SY the set when returning the set to customer.
board replacement using [READ and SAVE (Imager DRA)] of
“Restore Data” in the DATA tab of the Adjust manual.
After the SY board has been replaced, write the data extracted from
the set before the SY board replacement in the set using “Imager
DRA Data Write” in the ADJUST tab of the Adjust manual.
• When the imager data is not extracted from the set before the SY
board replacement, consult with each Head Quarters.
1-1
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.1
P: Pitch Sensitivity Value 5. Confirm on the personal computer that the unit is detected as a
SE7701 Y: Yaw Sensitivity Value connectable wireless network.
6. To further confirm that the unit is connectable, connect the unit
to the personal computer and double-click the “current connec-
tion” from the icon displayed on the notice field, make sure that
the unit is displayed in the Wireless internet access column.
Note: The sensitivity value is written only on repair parts.
The Pitch/Yaw Sensitivity Value is written by 1-digit number.
2. After the GY-1018 board has been replaced, execute “Set Gyro
Sensor Data” on the ADJUST tab by using the Adjust manual to
write the adjustment values.
DIRECT-XXXX:MODEL-NAME
1-2E
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2. DISASSEMBLY & ASSEMBLY
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK NG NG
(The flexible board was plugged in straight (The flexible board was plugged in (The flexible board was not plugged in
and completely) crooked.) completely.)
Flexible Flexible
Board Flexible Flexible Board Flexible
Board Board Reference Board
Reference Flexible
line Reference Board line
line
When opening the connector's holder in direction A, do not open When closing the connector's holder, press it evenly while pushing
it with excessive force. a flexible board in direction B.
Holder Holder
A Connector
Flexible Board
Connector
A Flexible Board
B
Insulation side
• Make sure that the flat cable and flexible board are not cracked Cut and remove the part of gilt
or bent at the contact end. which comes off at the point.
(Be careful or some
• Do not apply excessive force to the gilded flexible board. pieces of gilt may be left inside)
SERVICE TOOLS
2-1
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
VF block
LCD panel block
SY-1098/1118 board
BT block
MB charge unit
MB N frame block
2-2
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-2. DISASSEMBLY
• Disassembled in the order shown in the flowchart below.
MAIN UNIT
2-2-2. FRONT GRIP RUBBER 2-2-21. LOUDSPEAKER BLOCK 2-2-42. FP-2438 FLEXIBLE BOARD 2-2-48. SHUTTER BLOCK 2-2-49. MB CHARGE UNIT,
(Page 2-4) (Page 2-17) (Page 2-34) (Page 2-38) SHUTTER UNIT (AFE-3379)
(Page 2-39)
2-2-3. SIDE CABINET ASSY 2-2-22. JK-1027 FLEXIBLE BOARD 2-2-43. SY-1098/1118 BOARD 2-2-50. TERMINAL UNIT BLOCK
(Page 2-4) (Page 2-18) (Page 2-35) (Page 2-39)
2-2-4. BT LID ASSY 2-2-23. VF BLOCK 2-2-44. SY MAIN FRAME BLOCK 2-2-51. MB N FRAME BLOCK 2-2-58. MB N PLATE A,
(Page 2-5) (Page 2-19) (Page 2-36) (Page 2-40) MB N PLATE SP1/SP2
(Page 2-44)
2-2-5. BOTTOM COVER PLATE 2-2-24. COLOR EVF UNIT 2-2-26. TOP COVER BLOCK 2-2-45. ANTI SHAKE UNIT 2-2-52. NFC BASE BLOCK
(Page 2-5) (Page 2-19) (Page 2-21) (Page 2-36) (Page 2-40) 2-2-59. MB LL BUTTON BLOCK
(Page 2-44)
2-2-6. BOTTOM COVER ASSY, 2-2-25. ES-1005 FLEXIBLE BOARD, 2-2-27. GY-1008 BOARD 2-2-46. IM IMAGER BLOCK, 2-2-53. BT BLOCK,
BOTTOM INNER PLATE ASSY VF BLOCK ASSY (Page 2-22) TEX-5300 FRONT COVER B-ASSY 2-2-60. CONTACT BLOCK
(Page 2-6) (Page 2-20) (Page 2-37) (Page 2-41) (Page 2-45)
2-3
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Note: Disassemble in the order indicated by the numbers assigned to the parts in the figures such as 1.
top side
front side
rear side
bottom side
top side
2-4
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
bottom side
5 BT lid assy
front side
bottom side
front side
2-5
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
bottom side
front side
2-6
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
rear side
2 tapping screw (1.4 u 5)
rear side
bottom side
8 three screws (M1.7 u 4)
7 Open the media lid.
rear side
bottom side
2-7
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
top side
7 two screws
(M1.7 u 2.5)
front side
1 screw (M1.7 u 2)
5 LC-1048/1053 flexible board
3 claw
4 rear FPC retainer block 6 two hooks
2-8
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1 two bosses
front side
2-9
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2 screw
(special M1.4 u 2 (D2.75))
2 screw
(special M1.4 u 2 (D2.75))
sheet LCD FPC adhesive
front side
bottom side
7 four claws
2-10
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
1 Open the hinge block.
bottom side
hook
4 Remove the hinge block in
hook the direction of the arrow.
hole
claw rib
6 panel B-assy
rib
5 hinge block
3 Draw the LC-1048/1053 flexible board out of the hole.
– Rear view –
LC CAB rear
cushion LC-FPC-WP
1 claw
front side
4 hinge assy
top side
2-11
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
7KHPHGLDOLGEORFNFDQEHGLVDVVHPEOHG
5 Draw the media lid shaft out of the hole.
6 media lid block DVVKRZQLQWKHILJXUHEHORZ
2-12
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
– Front view –
bottom side
qd Disconnect the
flexible board.
joy holder plate
joy rubber
2-13
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
bottom side
– Rear view –
rear side
2-14
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
bottom side
5 KY-1028 flexible
board block 4 claw
7KH.<IOH[LEOHERDUGEORFNFDQEH
GLVDVVHPEOHGDVVKRZQLQWKHILJXUHEHORZ
front side
rear button plate R
bottom side
3 three bosses
2-15
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1 AEL rubber
3 AF rubber
5 REC FN rubber
front side
7 C3 menu rubber
8 menu button
9 C3 button
bottom side
6 REC button
LC lock WP cushion
LC lock
bottom side
front side
1 rear EV WP cushion
5 LC WP cushion
bottom side
2-16
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
7KHORXGVSHDNHUEORFNFDQEHGLVDVVHPEOHG
DVVKRZQLQWKHILJXUHEHORZ
loudspeaker (1.0 cm)
two solders
cable
rear side
bottom side
5 SP insulation sheet
bottom side
2-17
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 CN protection sheet
2 top connect rear plate
– Rear view –
7 JK holder
rear side
5 connector
4 Remove the harness from the ribs.
bottom side
2-18
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-2-23. VF BLOCK
4 VF block
3 two hooks
rear side
bottom side
1 VF radiation sheet
2 VF blind sheet
4 claw
front side
bottom side
2-19
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Bottom view –
3 two hooks
2 Peel off the ES-1005 flexible board.
rear side
bottom side
5 two bosses
rear side
bottom side
7 VF block assy
2-20
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
rear side
2-21
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
4 hook 3 boss
1 screw (M1.7 u 2.5)
3 boss
rear side
– Bottom view –
bottom side
rear side
0 GY-1008 board
top side
8 gyro holder
rear side
2-22
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
bottom side
rear side
2-23
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
rear side
– Bottom view –
bottom side
rear side
2-24
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
3 eyelet plate G
bottom side
rear side
2-25
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
eyelet triangle
3 C1 button
2 C2 button
5 eyelet G block
4 boss
bottom side
– Bottom view –
rear side
3 AN-1034 board
2-26
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
7KHH\HOHW/EORFNFDQEHGLVDVVHPEOHG
DVVKRZQLQWKHILJXUHEHORZ
eyelet triangle holder
eyelet triangle
4 eyelet L block
–%RWWRPYLHZ–
3 boss
bottom side
front side
2-27
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
3 two bosses
7KH(9)SURWHFWRUEORFNFDQEHGLVDVVHPEOHG
DVVKRZQLQWKHILJXUHEHORZ
EVF protector
6 boss
bottom side
front side
2-28
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1 CN protection sheet
bottom side
rear side
2 MIS-2006 flexible board 5 Draw the MIS-2006 flexible board out of the hole.
Note: Take care not to damage
the flexible board.
2-29
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 two ribs
2 boss
3 three ribs
rear side
bottom side
rear side
–7RSYLHZ–
6 two solders
6 two solders
8 microphone block
7 microphone rubber
8 microphone block
7 microphone rubber
2-30
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-2-37. TOP WP CUSHION F6/R6, MD DIAL B-ASSY, CONTROL SWITCH BLOCK (EV88100)
bottom side
2 top WP cushion F6
1 top WP cushion R6
4 tapping screw
(1.7 u 4.0)
6 two screws (M1.7 u 2.5)
rear side
5 MD dial B-assy
2-31
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2 rib
top side
3 two ribs
1 shoe cap
top side
rear side
3 two ribs
2-32
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
top side
rear side
top side
rear side
2-33
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
2 two bosses
2-34
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
SY-1098/1118 board
1 GF sheet AS
GF sheet AS
– Bottom view –
rear side
rear side qa MB charge unit
flexible board SY-1098/1118 board
9 TEX-5300
flexible board
8 ISP-2008
flexible board
7 ISL-2009
flexible board
bottom side
bottom side
qh SY-1098/1118 board
2 BTFPC protection sheet
qg sheet CHG FPC protect qd Draw the three flexible boards and
3 BT-2019 flexible board
GF sheet LE out of the hole.
Note: Take care not to damage
the flexible board.
4 GF sheet LE
2-35
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Hold here.
6 three IM adjust washers D
Note 2: Take note of the amount of
IM adjust washers D.
rear side
bottom side
2-36
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
9 IM imager block
qs IM radiation sheet B
0 IM radiation sheet C
8 Draw the two flexible boards out
of the hole of the TEX-5300.
qd TEX-5300
2-37
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
2 shutter block
2-38
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Rear view –
top side
2 claw
5 MB charge unit
3 shutter unit (AFE-3379)
front side
top side
SYNC holder
4 terminal unit block
2-39
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
2 MB N frame block
rear side
7KH1)&EDVHEORFNFDQEHGLVDVVHPEOHG
top side DVVKRZQLQWKHILJXUHEHORZ
WP cushion NFC
NFC base
NFC adhesive
NFC antenna
cable
1 three screws
rear side (M1.7 u 2.5)
3 connector
2 claw
2-40
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
2 Peel off the VG-1007
flexible board.
3 hook
6 hook
4 two bosses
– Top view –
9 boss
qs BT block
2-41
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
– Right view –
2 claw
rear side
– Right view –
3 hook
top side
2 boss
5 hook
4 boss
front side
5 hook
2-42
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
– Front view –
4 hook
2 lithium secondary
front side battery
top side
4 BTH assy
3 adhesive BT FPC
2 gyro cushion
1 GY-1018 board
front side
2-43
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1 three screws
(0+P1 M2 u 6) (SPIN)
1 three screws
(0+P1 M2 u 6) (SPIN)
2 MB N plate A
4 MB N plate SP2
front side
bottom side
7KH0%//EXWWRQEORFNFDQEH
GLVDVVHPEOHGDVVKRZQLQWKH
ILJXUHEHORZ
MB LL button MB LL pin
1 MB LL button block
2 MB LL button spring
front side
bottom side
2-44
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
hole B
bottom side
front side
MB N holder A
bottom side
hole A
2 boss
2 boss
rear side
top side
1 MB mask sheet
3 MB N frame block
rear side
top side
2-45
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-3. ASSEMBLY
• Assemble in the order shown in the flowchart below. BTH ASSY REAR COVER B-ASSY
2-3-56. JOY KNOB
(Page 2-92)
2-3-10. VG-1007 FLEXIBLE BOARD
2-3-1. ASSEMBLY FLOW (Page 2-53)
2-3-8. GY-1018 BOARD 2-3-50. WP CUSHIONS
(Page 2-51) (Page 2-87) REAR PLATE
2-3-11. BT-2029 FLEXIBLE BOARD
FRONT COVER B-ASSY
(Page 2-54)
2-3-9. DL-1005 FLEXIBLE BOARD 2-3-51. AEL/AF/REC/MENU/C3 BUTTON 2-3-57. JS-1012 FLEXIBLE BOARD,
(Page 2-52) (Page 2-88) SW-1033 FLEXIBLE BOARD
2-3-12. BT BLOCK (Page 2-93)
MB N FRAME BLOCK NFC BASE
(Page 2-55)
TOP COVER BLOCK KY-1028 FLEXIBLE BOARD
2-3-58. REAR PLATE BLOCK
2-3-2. MB MASK SHEET 2-3-14. NFC BASE BLOCK 2-3-13. NFC ANTENNA (Page 2-94)
(Page 2-47) (Page 2-57) (Page 2-56)
2-3-26. MI SHOE FIX PLATE 2-3-52. REAR BUTTON PLATE L/R
(Page 2-65) (Page 2-89)
PANEL B-ASSY
MB N HOLDER A
2-3-15. MB N FRAME BLOCK 2-3-27. MIS-2006 FLEXIBLE BOARD 2-3-53. KY-1028 FLEXIBLE BOARD BLOCK
(Page 2-57) (Page 2-66) (Page 2-89) HINGE ASSY
2-3-3. MB N CONTACT UNIT
(Page 2-47)
2-3-28. MI SHOE SHELL PLATE 2-3-54. RS-1015/1020 FLEXIBLE BOARD
SYNC HOLDER 2-3-59. MEDIA LID ASSY 2-3-60. LC CAB REAR
(Page 2-67) (Page 2-90)
2-3-4. CONTACT BLOCK (Page 2-95) (Page 2-96)
(Page 2-48)
2-3-16. TERMINAL UNIT 2-3-29. MI SHOE SCREW COVER 2-3-55. CONTROL SWITCH BLOCK (BK88100)
(Page 2-58) (Page 2-67) (Page 2-91) 2-3-61. HINGE BLOCK
2-3-5. MB LL BUTTON (Page 2-96)
(Page 2-49)
2-3-17. TERMINAL UNIT BLOCK 2-3-30. MI SHOE SPRING PLATE
(Page 2-58) (Page 2-68) 2-3-62. LC CAB REAR PLATE
2-3-6. MB N PLATE SP1/SP2 (Page 2-97)
(Page 2-49)
2-3-31. CONTROL SWITCH BLOCK (EV88100)
SHUTTER UNIT (AFE-3379)
(Page 2-69) 2-3-63. FLEXIBLE CAP (LC)
2-3-7. MB N PLATE A (Page 2-98)
(Page 2-50)
2-3-18. MB CHARGE UNIT 2-3-32. MD DIAL B-ASSY,
(Page 2-59) TOP WP CUSHION F6/R6 2-3-37. TOP CONNECT PLATE L 2-3-64. LCD PANEL BLOCK
(Page 2-70) (Page 2-74) (Page 2-99)
2-3-21. TEX-5300 2-3-35. SH FPC BASE BLOCK 2-3-41. RL BLOCK ASSY-2 2-3-46. COLOR EVF UNIT 2-3-68. BOTTOM COVER PLATE
(Page 2-61) (Page 2-72) (Page 2-8) (Page 2-83) (Page 2-102)
2-3-22. ANTI SHAKE UNIT 2-3-36. EVF PROTECTOR 2-3-42. CNT DIAL F ASSY 2-3-47. VF BLOCK 2-3-69. BT LID ASSY
(Page 2-62) (Page 2-73) (Page 2-79) (Page 2-84) (Page 2-103)
2-3-23. SY MAIN FRAME ASSY 2-3-25. FP-2438 FLEXIBLE BOARD 2-3-43. GY-1008 BOARD 2-3-48. JK-1027 FLEXIBLE BOARD 2-3-70. SIDE CABINET ASSY
(Page 2-63) (Page 2-65) (Page 2-80) (Page 2-85) (Page 2-103)
2-3-24. SY-1098/1118 BOARD 2-3-44. TOP COVER BLOCK 2-3-49. LOUDSPEAKER (1.0 cm) 2-3-71. FRONT GRIP RUBBER
(Page 2-64) (Page 2-81) (Page 2-86) (Page 2-104)
2-46
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Note: Assemble in the order indicated by the numbers assigned to the parts in the figures such as 1.
1 MB mask sheet
rear side
4 MB N frame block
rear side top side
groove
groove
1 MB N contact unit
2 MB F prevention sheet
5 claw 3 MB N holder A
front side
2-47
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1 contact block
– Front view –
hole A
2 Fold the flexible board in the valley.
front side
3 Insert the flexible board into hole A, and
WKHQSXOOLWRXWIURPKROHB.
Note 2: Take care not to damage
the flexible board.
hole B
5 boss
ERWWRPVLGH
6 Paste the flexible board.
5 boss
rear side
top side
2-48
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-3-5. MB LL BUTTON
4 MB LL button 5 MB LL pin
6 MB LL button block
3 MB LL button spring
front side
1 Apply grease
G-85
bottom side
4 MB N plate SP2
5 Apply grease
1 MB N plate SP1 G-85
rear side
2 Apply grease
G-85
rear side
6 two bosses
4 MB N plate SP2
front side
3 two bosses
6 two bosses
bottom side
2-49
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-3-7. MB N PLATE A
2 MB LL pin
front side
bottom side
3 screw 6 screw
(0+P1 M2 u 6) (SPIN) (0+P1 M2 u 6) (SPIN)
1P 1P
7 screw 8 screw
(0+P1 M2 u 6) (SPIN) (0+P1 M2 u 6) (SPIN)
1P 1P
2-50
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
1 BTH assy
– Rear view –
2 adhesive
BT FPC
: guide line
front side
– Front view –
: guide line ± 0.3 mm ± 0.3 mm
± 0.3 mm ± 0.3 mm
2-51
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
5 two bosses
3 boss
2 hook
± 0.5 mm
± 0.5 mm
: guide line
2-52
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2 two bosses
– Front view –
front side
6 VG FPC fix plate
– Right view –
: guide line
9 hook
7 hook
0 boss
8 boss
7 hook
9 hook
2-53
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
2 claw
rear side
3 two bosses
– Right view –
2-54
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-3-12. BT BLOCK
rear side
2 BT block
8 hook
9 two bosses
– Top view –
qa hook
2-55
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
0 to 0.5 mm
1 NFC antenna
0 to 0.5 mm
– Right view –
0 to 0.5 mm
5 NFC adhesive
0 to 0.5 mm
– Right view –
rear side
NFC base
– Right view –
4 NFC base top side
top side
– Left view –
right side
0 to 0.5 mm
rear side
2-56
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
4 three screws
rear side (M1.7 u 2.5)
1P
2 connector
3 claw
top side
3 two bosses
1 MB N frame block
rear side
± 0.5 mm
± 0.5 mm
4 four screws (M2 u 4.0)
1P
2-57
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2 terminal unit
5 two bosses
,QVWDOOLQJGLUHFWLRQRIWKH 4 SYNC GND plate
WHUPLQDOXQLW
1 SYNC holder
20°
rear side
top side
– Outside view –
2 Insert the SYNC harness into
the hole.
Note: Take care not to damage SYNC harness
the harness.
3.0 mm
0 to 1.0 mm
3 two bosses
rear side
4 two screws (M1.7 u 2.5)
1P 0 to 1.0 mm
– Inner view –
5 SYNC harness sheet
2-58
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Rear view –
top side
3 claw
2 MB charge unit
1 shutter unit (AFE-3379)
front side
2 boss
top side
2 boss
1 shutter block
2-59
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Note 1: When install the spacer sheet to the imager and the
optical filter block, install them so that the each
centers are matched and top and bottom right and
left become uniform.
1 IS-1037 board
imager 6 Connect the ISP-2008 8 Connect the ISL-2009
2 spacer sheet flexible board. flexible board.
–5HDUYLHZ–
,QVWDOODWLRQGLUHFWLRQIRUWKHRSWLFDOILOWHUEORFN
4 IM shield sheet IS-1037 board
optical filter block
: guide line
2-60
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
6 IM imager block
rear side
3 IM radiation sheet B
5 IM radiation sheet C
–)URQWYLHZ–
top side
qd hook
pin (Ø 1.22 ± 0.01)
qa claw
9 IM glass retainer plate front side
top side
3DVWLQJSRVLWLRQRIWKH$6JUDSKLWH
VKHHW,0*
: guide line
qg two AS graphite sheets IMG
Note: This parts be not reused.
Be sure to replace them with new parts.
2-61
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3DVWLQJSRVLWLRQRIWKH$6JUDSKLWHVKHHWWRS
: guide line
– Top view – AS graphite sheet top
3DVWLQJSRVLWLRQRIWKH63KDUQHVV
JXLGHVKHHW
– Rear view –
: guide line SP harness guide sheet
– Rear view –
PP
PP
PP
PP
AS graphite sheet top
Hold here.
rear side
ERWWRPVLGH
: guide line
5 Paste the AS graphite sheet BTM 5 Paste the AS graphite sheet BTM
Note 4: Do not detach or reattach the AS Note 4: Do not detach or reattach the AS
graphite sheet BTM more than 5 times. graphite sheet BTM more than 5 times.
2-62
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Rear view –
7 MF SY protect sheet
8 GF sheet LE ± 0.5 mm
± 0.5 mm
2 FPC guide sheet 0 to 0.5 mm
2-63
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Front view –
: guide line 1 SY-1098/1118 board
0 to 0.5 mm 5 Insert the three flexible boards and GF sheet LE
into the hole of the SY-1098/1118 board block.
0 to 0.5 mm Note 1: Take care not to damage
the flexible board.
rear side
bottom side
0 two screws (M1.7 u 2.5)
(0.12 ± 0.02 N•m)
0 three screws (M1.7 u 2.5)
rear side 8 MB charge unit SY-1098/1118 (0.12 ± 0.02 N•m)
flexible board board
: guide line
qg shutter unit flexible board
qh GF sheet LE
± 0.5 mm
GF sheet AS ql GF sheet AS
± 0.5 mm
top side
2 two bosses
bottom side
rear side
3 two bosses
2-65
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
top side
bottom side
– MIS-2006 flexible board side –
front side
– Bottom view – : guide line
0 to 0.2 mm 0 to 0.2 mm
4 Install the MI shoe FPC WP rubber.
top side
rear side
2-66
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
rear side
top side
rear side
2 two ribs
– Bottom view –
two bosses
2-67
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
4 two ribs
2-68
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
,QVWDOOLQJGLUHFWLRQRIWKH(9
2 EV dial FPC WP rubber GLDO)3&:3UXEEHU
top side
front side
bottom side
EV dial FPC WP rubber
top side
front side
3 Insert the control switch block (EV88100) flexible board into the hole.
Note: Take care not to damage the flexible board.
bottom side
front side
2-69
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
WRPP
– Rear view – JXLGHOLQH
5 top WP cushion F6
ERWWRPVLGH
4 AEL button retainer sheet
WRPP
WRPP
WRPP UHDUVLGH
JXLGHOLQH
PP 2 two bosses
– Rear view –
10'GLDO%DVV\
– Top view –
5 Soldering.
[white]
5 Soldering.
[black]
5 Soldering.
5 Soldering.
[white]
[black]
3 microphone block
4 microphone rubber
3 microphone block
4 microphone rubber
2-70
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
bottom side
1 SH FPC base
± 0.5 mm
5 two ribs
6 boss
5 three ribs
2-71
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 boss
3 boss
ERWWRPVLGH
rear side
7 CN protection sheet
WRPP
WRPP
2-72
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2 GLRSWHUFRYHU:3VKHHW%
PP
PP 5 boss
1 EVF protector
JXLGHOLQH
6DGKHVLYH
tape
JXLGHOLQH
4,QVHUWWKH6+IOH[LEOHERDUGLQWR
WKHKROH
Note: Take care not to damage
the flexible board.
7,QVWDOOWKH(9)SURWHFWRUEORFN
LQWKHGLUHFWLRQRIWKHDUURZ
ERWWRPVLGH
IURQWVLGH
IURQWVLGH
8 boss 8 boss
2-73
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
5 eyelet triangle
4 eyelet L
6 eyelet triangle holder
1 top connect plate L
7 eyelet L block
– Bottom view –
8 boss
bottom side
2 two bosses
front side
2-74
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
5 boss
– Top view –
1 Align the D-shaped hole of MD dial
B-assy as shown in the figure below.
bottom side
5 boss
rear side
– Bottom view –
2-75
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Note: When attaching the eyelet G to the top cover block, crush the entire
cushion WP eyelet G in the direction of thickness for a while, and be
careful not to twist the cushion WP eyelet G.
(Estimate: crush for 40 seconds or more)
1 eyelet G
2 eyelet triangle
,QVWDOOLQJGLUHFWLRQRIHDFKEXWWRQ
C1 button C2 button
6 C1 button
7 C2 button
4 eyelet G block
5 boss
bottom side
0 two bosses
rear side
– Bottom view –
2-76
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
± 0.5 mm
0 to 0.5 mm
RL-1061 flexible board
: guide line
– Bottom view –
boss
5 Insert the LED part into the hole.
boss
bottom side
rear side
0 eyelet plate G
qa two bosses
2-77
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
boss
boss ERWWRPVLGH
rear side
: guide line
ERWWRPVLGH
rear side
2-78
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
boss boss
2,QVWDOOWKH&17GLDO)DVV\
boss boss
ERWWRPVLGH
hole hole
hole hole
UHDUVLGH
2-79
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1*<ERDUG
2J\URFXVKLRQ7
WRSVLGH
3J\URKROGHU
UHDUVLGH
ULE
4*<ERDUGEORFN
5/IOH[LEOHERDUG
7 boss
UHDUVLGH
– Bottom view –
ERWWRPVLGH
55/IOH[LEOHERDUG
UHDUVLGH
2-80
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
top side
rear side
2-81
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Top view –
: guide line 4 two bosses
0 to 0.5 mm 0 to 0.5 mm
0 to 0.5 mm rear side
0 to 0.5 mm
bottom side
1 VF block assy
8 two tapes (AS 1/2) (C)
– Bottom view –
6 two hooks : guide line
7 Paste the ES-1005 flexible board.
rear side
bottom side
2-82
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
0 to 0.5 mm
center
– Front view –
: guide line
0 to 0.5 mm
0 to 0.5 mm
2 claw
– Bottom view –
: guide line
VF flexible adhesive sheet
1 color EVF unit
5 Fold the VF blind sheet.
2 claw
front side
3 Paste the EVF flexible board.
2-83
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-3-47. VF BLOCK
1 VF block
2 two hooks
rear side
bottom side
2-84
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
rear side
bottom side
qs rib
5 JK holder
8 Connect the connector.
qd boss
9 Arrange the harness between the ribs.
: guide line
± 0.5 mm
6 two bosses
0 CN protection
± 0.5 mm sheet
2-85
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 soldering. [red]
2 cable
3 soldering. [black]
rear side
bottom side
5 SP insulation sheet
bottom side
2-86
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2-3-50. WP CUSHIONS
: guide line
round
shape front side
bottom side
3 LC lock WP cushion
8 three gaskets
front side USB
round
shape
2 LC lock round
shape
front side
bottom side – Front view –
4 LC lock block
9 rear front WP
cushion
front side
front side
0 rear EV WP cushion
– Side view – Start position to paste
2-87
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
qs AEL rubber
0 AF rubber
8 REC FN rubber
front side
6 C3 menu rubber
2 menu button
1 C3 button
qd two bosses
bottom side
qa two bosses
7 two bosses
9 two bosses
3 REC button
,QVWDOOLQJGLUHFWLRQRIHDFKEXWWRQ
convex part convex part convex part menu button convex part
–)URQWYLHZ–
2-88
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
– Front view –
: guide line
center
0 to 1.0 mm
3 Align the four holes, and paste the rear
button plate R with adhesive sheet.
2 claw
front side
bottom side
3 three bosses
2-89
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
0 to 0.5 mm 0 to 0.5 mm
2 SY radiation sheet (RE)
0 to 0.5 mm
– Rear view –
4 RS protection sheet
: guide line
– Front view –
front side
bottom side
5 two bosses
2-90
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
4 REC FN rubber
5 two bosses
7 three bosses
9 two bosses
2-91
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 joy knob
2 joy rubber
6 two bosses
,QVWDOOLQJGLUHFWLRQRIWKHMR\NQREEORFN
: guide line
front side joy holder plate joy knob
bottom side
convex part
2-92
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 two bosses
rear side
– Rear view –
1 rear plate
bottom side
8 Align the five holes, and paste
the SW-1033 flexible board with
adhesive sheet.
2-93
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
bottom side
3 two bosses
2-94
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
,QVWDOOLQJGLUHFWLRQRIWKH
1 media lid assy PHGLDOLGURWDWLRQVSULQJ
5 mm
4 Slide the media lid inner cover in the direction of the arrow. top side
bottom side
rear side
top side
: guide line
rear side
center bottom side
± 0.5 mm
0 to 0.5 mm
7 Hook the media lid rotation spring.
hole
0 media lid WP sheet
2-95
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
hole
5 claw 6 Align the holes, and paste the LC CAB rear block.
hole
– Rear view –
2 LC CAB rear
4 cushion LC-FPC-WP
: guide line
5 claw
front side
hole
1 hinge assy
top side
hole
hook
rib 3 Open the hinge block.
claw rib
2 hinge block
1 panel B-assy
bottom side
rib
2-96
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
6 four claws
2-97
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
± 1.0 mm
2-98
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3 two screws
(M1.7 u 2.5)
front side (0.12 ± 0.02 N•m)
9 screw (M1.7 u 2)
(0.12 ± 0.02 N•m)
5 LC-1048/1053 flexible board
7 claw
6 rear FPC retainer block 4 two hooks
2-99
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
top side
1 two bosses
2-100
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
rear side
rear side
bottom side
bottom side
top side
2-101
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
2 rib
2 two ribs
bottom side
front side
bottom side
front side
2-102
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
1 BT lid assy
front side
rear side
bottom side
top side
3 two bosses
2-103
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
: guide line
– Left view –
1 grip adhesive 1
Note 1: This parts be not reused.
– Front view –
Be sure to replace them with new parts.
grip adhesive 1
inside of step
top side
front side
convex part
front grip
rubber
notch
3DVWLQJSRVLWLRQRIIURQWJULS
rubber
: guide line
front grip
rubber
– Left view –
2-104E
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
3. EXPLODED VIEWS
Note:
The components identified by mark 0 or dotted line with
• -XX and -X mean standardized parts, so they may have some dif-
mark are critical for safety.
ference from the original one. Replace only with part number specified.
• Items marked “*” are not stocked since they are seldom required
for routine service. Some delay should be anticipated when order- Les composants identifiés par une marque 0 sont
ing these items. critiques pour la sécurité.
• The mechanical parts with no reference number in the exploded Ne les remplacer que par une pièce portant le numéro
spécifié.
views are not supplied.
• Color Indication of Appearance Parts Caution
Example: Danger of explosion if battery is incorrectly replaced.
(SILVER) : Cabinet’s Color Replace only with the same or equivalent type.
(Silver) : Parts Color Dispose of used batteries according to the instructions.
⌞ᝅ
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
3-1. OVERALL SECTION 10
3 11
3 9 (Note)
3 front side
3
5
8
14 12
(Note)
3
4 3
13
3
2
1
rear side 3
4
3
15 6
Refer to rear cabinet section-1. 3
3
16
Note: This parts be not reused. Be sure to replace them with new parts.
3
Ref. No. Part No. Description Ref. No. Part No. Description
1 430010611 BTITE (1.4 (CH)) (L = 5.0 mm) 10 500370401 FRONT GRIP RUBBER (88100)
2 500367201 CV DIOPTER ADJUST DIAL (88100)
3 444694901 SCREW (M1.7) (L = 4.0 mm) 11 500369901 GRIP ADHESIVE 2 (88100) (Note)
4 444694931 SCREW (M1.7) (L = 2.5 mm) 12 500369801 GRIP ADHESIVE 1 (88100) (Note)
5 X25945931 EYE CUP ASSY (799) 13 X50002721 BT LID ASSY (88100)
14 X50002741 BUTTOM INNER PLATE ASSY (881)
6 263556211 SCREW (M1.7) (L = 2.5 mm) 15 X50002751 BOTTOM COVER ASSY (88100)
7 A5013740A FINDER COVER ASSY (SERVICE_881)
8 X50002601 SIDE CABINET ASSY (88100) 16 500393801 BOTTOM COVER PLATE (88100)
9 443873403 SHOE CAP (875)
3-1
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
57
63
55
54
A
53
54 61
52
60 61
61
51
62
front side
Ref. No. Part No. Description Ref. No. Part No. Description
51 259947501 SCREW (M1.7) (L = 2.0 mm) 58 500391001 MEDIA LID ROTATION SPRING (881)
52 A5013737A REAR FPC RETAINER (SERVICE881) 59 500607901 MEDIA LID WP CUSHION (88100)
53 500885701 MEDIA LID WP SHEET (88100) 60 500509201 LC WP CUSHION (88100)
54 469210701 GASKET (CN (799))
55 500509301 REAR EV WP CUSHION (88100) 61 500466901 GASKET USB (88100)
62 500607801 REAR FRONT WP CUSHION (88100)
56 X50002711 MEDIA LID ASSY (88100) 63 444694931 SCREW (M1.7) (L = 2.5 mm)
57 500391401 MEDIA LID SHAFT (88100)
3-2
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
123
122 124 125
121 126
133
119 128
129
127
101
113
E 101
131
130
118
120
101
rear side
114
113
109
108
107 112 132
105
104 111 116
110 E
102 117
D
101 106 B C
B
D
115
C
RS-1015/1020 116
134 flexible board
101 103
116
front side
Ref. No. Part No. Description Ref. No. Part No. Description
101 263556211 SCREW (M1.7) (L = 2.5 mm) 119 500389401 REAR BUTTON PLATE R (88100)
102 500390301 REAR PLATE (88100)
103 A5001913A SW-1033 FLEXIBLE BOARD, COMPLETE 120 500389301 REAR BUTTON PLATE L (88100)
104 A5001912A JS-1012 FLEXIBLE BOARD, COMPLETE 121 198411011 KY-1028 FLEXIBLE BOARD
105 500390201 JOY RETAINER PLATE (88100) 122 A5013739A AEL BUTTON RUBBER (SERVICE_881)
123 500388801 AEL BUTTON (88100)
106 100189111 SWITCH BLOCK, CONTROL (BK88100) 124 A5013738A AF BUTTON RUBBER (SERVICE_881)
107 500389901 JOY KNOB (88100)
108 A5014708A JOY HOLDER PLATE (SERVICE_881) 125 500388701 AF BUTTON (88100)
109 500390101 JOY RUBBER (88100) 126 500388601 REC BUTTON (88100)
110 500389801 PLAYBACK DELETE RUBBER (88100) 127 500388901 C3 MENU RUBBER (88100)
128 500388501 MENU BUTTON (88100)
111 500389601 PLAYBACK BUTTON (88100) 129 500388401 C3 BUTTON (88100)
112 500389701 DELETE BUTTON (88100)
113 500389001 REC FN RUBBER (88100) 130 500424001 LC LOCK (88100)
114 500389501 FN BUTTON (88100) 131 500684501 LC LOCK WP CUSHION (88100)
115 A5010653A RS-1015 B-ASSY (SERVICE) (88100) 132 A5010649A REAR COVER B-ASSY (SERVICE_881)
(including RS-1015 flexible board) (ILCE-7RM4) (ILCE-7RM4)
132 A5032248A REAR COVER B-ASSY (SERVICE_889)
115 A5029736A RS-1020 B-ASSY (SERVICE) (88900) (ILCE-7RM4A)
(including RS-1020 flexible board) (ILCE-7RM4A) 133 501161701 AF BUTTON RETAINER SHEET (881)
116 469210211 SHEET (RE (799)), SY RADIATION
117 472964401 RS PROTECTION SHEET (62200) 134 500885701 MEDIA LID WP SHEET (88100)
118 259947521 SCREW (M1.7) (L = 3.0 mm)
3-3
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
157
LCD901
158
rear side
156
153
155 151
152 155
151
154
front side
151
Ref. No. Part No. Description Ref. No. Part No. Description
151 417812401 SPECIAL (M1.4 (D2.75)) (L = 2.0 mm) 158 500392301 SHEET LCD FPC ADHESIVE (88100)
152 500365501 LC CAB REAR PLATE (88100) LCD901 A5010646A PANEL B-ASSY (SERVICE) (88100) (including
153 A5014707A LC CAB REAR (SERVICE) (88100) PD-1061 board and LC-1048 flexible board)
154 500411301 CUSION LC-FPC-WP (88100) (ILCE-7RM4)
155 500411501 ADHESIVE LC CAB REAR (88100) LCD901 A5029452A PANEL B-ASSY (SERVICE) (88900) (including
PD-1069 board and LC-1053 flexible board)
156 X50002522 HINGE ASSY (88100) (ILCE-7RM4A)
157 455916201 CAP (LC) (786), FLEXIBLE
3-4
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
209
front side
208
207
204 205
204 206 207 I
202
not 209
supplied LCD902 207
214 215
212 G
213 Refer to main board section.
209
Ref. No. Part No. Description Ref. No. Part No. Description
201 A2196477A ES-1005 FLEXIBLE BOARD, COMPLETE 210 A5001911A JK-1027 FLEXIBLE BOARD, COMPLETE
202 A5013324A VF BLOCK ASSY (SERVICE) (88100)
203 457581811 SHEET, VF FLEXIBLE ADHESIVE 211 500366701 JK HOLDER (88100)
204 427498701 TAPE (AS 1/2) (C) 212 500462501 CN PROTECTION SHEET (88100)
205 472950001 VF BLIND SHEET (62000) 213 184678731 CABLE
214 500373601 SPEAKER GND SHEET (88100)
206 457578001 VF SHEET, RADIATION (795) 215 500463101 SP INSULATION SHEET (88100)
207 263556211 SCREW (M1.7) (L = 2.5 mm)
208 500385501 TOP CONNECT REAR PLATE (88100) LCD902 875607342 ECX339AA-1 (COLOR EVF UNIT)
209 444694901 SCREW (M1.7) (L = 4.0 mm) SP901 185921011 LOUDSPEAKER (1.0 cm)
3-5
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
267
268
267 267
269
253
270
267
267 K 266
RL-1061
flexible board
L L
271
265 J
277
273 267 272
261 260 253
259
263 264 267
258 274
275
262
276
K
257
255 bottom side
254
253
front side
J 256
Ref. No. Part No. Description Ref. No. Part No. Description
251 500946801 TOP WP CUSHION R6 (88100) 266 100203811 SWITCH BLOCK, CONTROL (RL88100)
252 A5001902A AN-1034 BOARD, COMPLETE 267 263556211 SCREW (M1.7) (L = 2.5 mm)
253 430011311 TAPPING (1.7) (CH) (L = 4.0 mm) 268 X50002651 CNT DIAL F ASSY (88100)
254 184647441 CABLE, COAXIAL (45 mm) 269 259947541 SCREW (M1.7) (L = 5.0 mm)
255 500946701 TOP WP CUSHION F6 (88100) 270 500386201 GYRO HOLDER (88100)
256 501161801 AEL BUTTON RETAINER SHEET (881) 271 469257201 CUSHION (T (799)), GYRO
257 500683501 FPC 2438 PROTECT SHEET (88100) 272 A2064122A GY-1008 BOARD, COMPLETE
258 500385801 CUSTOM BUTTON RUBBER (88100) 273 259947521 SCREW (M1.7) (L = 3.0 mm)
259 A5013735A EYELET G (SERVICE) (88100) 274 500391701 AF FIXED FRAME (88100)
260 453170302 EYELET TRIANGLE (775) 275 500385601 C1 BUTTON (88100)
261 448787501 HOLDER, EYELET TRIANGLE (779) 276 500385701 C2 BUTTON (88100)
262 500387201 EYELET PLATE G (88100) 277 500885701 MEDIA LID WP SHEET (88100)
263 418654511 SCREW, 0+Z M1.7 SG (SPIN) (L = 5.5 mm)
264 444694901 SCREW (M1.7) (L = 4.0 mm)
265 A5010650A RL BLOCK ASSY (SERVICE) (88100)
(including RL-1061 flexible board)
3-6
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Ver. 1.2
322 316
321
MIC901
MIC902
320
321
319
318 317
M
316
315
326
311 319
310
312 323
not supplied
not supplied
324 325
308 332
M
330
306 327
328
305 329
307
304 304
303
301
302
Ref. No. Part No. Description Ref. No. Part No. Description
301 500294501 MI SHOE SPRING PLATE (88100) 320 A5001909A SH-1024 FLEXIBLE BOARD, COMPLETE
302 428743511 SCREW (M1.4 EUROPE) TYPE (L = 1.4 mm) 321 469223601 RUBBER (799), MICROPHONE
303 500294601 MI SHOE SCREW COVER (88100) 322 500386401 EVF PROTECTOR (88100)
304 500294701 SCREW (M1.7) SPECIAL HEAD (L = 3.3 mm) 323 500385301 TOP CONNECT PLATE L (88100)
305 500294301 MI SHOE SHELL PLATE (88100)
324 327048301 GRIP, (M1.7 X 4.0) (2 MAIN EG)
306 259947521 SCREW (M1.7) (L = 3.0 mm) 325 259947541 SCREW (M1.7) (L = 5.0 mm)
307 A5010651A MD DIAL B-ASSY (CERVICE) (88100) 326 A5010648A TOP COVER B-ASSY (SERVICE_881)
308 100189211 SWITCH BLOCK, CONTROL (EV88100) 327 A5013734A EYELET L (SERVICE) (88100)
310 218734521 SCREW (M1.7), P2 (L = 2.5 mm) 328 453170302 EYELET TRIANGLE (775)
311 430011311 TAPPING (1.7) (CH) (L = 4.0 mm)
329 448787501 HOLDER, EYELET TRIANGLE (779)
312 500395901 MI SHOE FIX PLATE (88100) 330 A5001908A MIS-2006 FLEXIBLE BOARD, COMPLETE
315 500386301 SH FPC BASE (88100) 331 500374001 DIOPTER COVER WP SHEET B (881)
316 444694901 SCREW (M1.7) (L = 4.0 mm) 332 501695501 MI SHOE FPC WP RUBBER(850)
317 501155801 MIC FPC ADHESIVE SHEET (88100) MIC901 154272181 MICROPHONE BLOCK (L)
318 500462501 CN PROTECTION SHEET (88100)
MIC902 154272181 MICROPHONE BLOCK (R)
319 263556211 SCREW (M1.7) (L = 2.5 mm)
3-7
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
359
U
NO
361
360 P T
353 Q
S
R
362
353 357
(Note)
356 358
353
U 359
351 353
N
355 359
(Note)
R T
O 354
P S
Q
353
352 353
rear side
Note: This parts be not reused. Be sure to replace them with new parts.
Ref. No. Part No. Description Ref. No. Part No. Description
351 500366801 GF SHEET AS (88100) (Note) 356 500806301 SHEET CHG FPC PROTECT (88100)
352 500462601 BTFPC PROTECTION SHEET (88100) 357 500366901 GF SHEET LE (88100) (Note)
353 263556211 SCREW (M1.7) (L = 2.5 mm) 358 500671301 MF SY PROTECT SHEET (88100)
354 A5009424A SY-1098 BOARD, COMPLETE (SERVICE) 359 444694901 SCREW (M1.7) (L = 4.0 mm)
(ILCE-7RM4)
354 A5028417A SY-1118 BOARD, COMPLETE (SERVICE) 360 X50002551 SY MAIN FRAME ASSY (88100)
(ILCE-7RM4A) 361 500463001 SP HARNESS GUIDE SHEET (88100)
362 469252011 SHEET (799), FPC GUIDE
355 198422111 FP-2438 FLEXIBLE BOARD
3-8
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
401
401
401
401 403
404
405
406
405
ANT901
V
405
Ref. No. Part No. Description Ref. No. Part No. Description
401 430011311 TAPPING (1.7) (CH) (L = 4.0 mm) 406 500369401 NFC ADHESIVE (88100)
402 500369501 NFC PERFORMANCE SHEET (88100) 407 184678731 CABLE
403 500708401 WP CUSHION NFC (88100) ANT901 175497212 NFC ANTENNA
404 500369701 NFC BASE (88100)
405 263556211 SCREW (M1.7) (L = 2.5 mm)
3-9
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
456
BH0001
455 (Note)
454
rear side
BT0001
(Note)
453
front side
457
458
Note: Replace the battery socket (Ref. No. BH0001) together when replacing
the lithium secondary battery (Ref. No. BT0001) on the DL-1005 flexible
board (The battery socket removed once cannot be used again). When
mounting these parts, mount new battery socket on the DL-1005 flexible
board first and attach new lithium secondary battery next.
Ref. No. Part No. Description Ref. No. Part No. Description
451 A5009325A BT SOLDER (including BT-2029 flexible board) 456 A5001905A DL-1005 FLEXIBLE BOARD, COMPLETE
452 500371201 VG FPC FIX PLATE (88100) 457 469214901 CUSHION (799), GYRO
453 A5001907A VG-1007 FLEXIBLE BOARD, COMPLETE 458 A5009700A GY-1018 BOARD, COMPLETE (SERVICE)
454 500923501 ADHESIVE BT FPC (88100) 0 BH0001 125192821 SOCKET, BATTERY (Note)
455 X50002591 BTH ASSY (88100) 0 BT0001 152890034 BATTERY, LITHIUM SECONDARY (Note)
3-10
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
front side
514
513
J901
501 514
(Note 1) 516
512 511
510
509
507
506
505
Refer to MB N frame unit section.
508
504
not supplied
(Note 2) 509
502
(Note 3) 515
504 504
not supplied
(Note 2)
not supplied
(Note 2)
Note 2: The IM adjust washers differ in thickness. Make sure to return the
removed IM adjust washers to original places.
Do not lose them.
Note 3: This parts be not reused. Be sure to replace them with new parts.
Ref. No. Part No. Description Ref. No. Part No. Description
501 A5012098A SERVICE, DEVICE UNIT (5600) (Note 1) 511 259947521 SCREW (M1.7) (L = 3.0 mm)
502 468511601 AS GRAPHITE SHEET TOP (5300) (Note 3) 512 500373401 SYNC GND PLATE (88100)
503 263000501 SCREW (M2), NEW TRUSTER, P2 (L = 5.0 mm) 513 500373201 SYNC HOLDER (88100)
504 474837101 MB CH FLOATING SHAFT (5600) 514 263556211 SCREW (M1.7) (L = 2.5 mm)
505 A2231470A MB CHARGE UNIT (5600) 515 500806301 SHEET CHG FPC PROTECT (88100)
506 472900201 MB CUSHION SHEET (5400) 516 A5010647A FRONT COVER B-ASSY (SERVICE 881)
507 149306113 SHUTTER UNIT (AFE-3379) J901 A2185509A SERVICE, TERMINAL UNIT SOLDER
508 418599001 MB SCREW, CHARGE UNIT FIXED (M1.6 X 4.5) (SYNCHRONISE TERMINAL UNIT)
509 263000531 SCREW (M2), NEW TRUSTER, P2 (L = 4.0 mm)
510 500373101 SYNC HARNESS SHEET (88100)
3-11
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
562
rear side
556
557
560
558 564
(Note 3) (Note 3)
559
551 560
555 563
554 558
(Note 1) (Note 3) 561
553
not supplied
(All mounted parts and IS-1037 complete board are not supplied,
552 but they are included in device unit service (5600) (Ref. No. 501).)
(Note 2)
551
front side
Note 1: Refer to “5. CLEANING” on page 5-1 for method of cleaning the OLPF.
Note 2: The imager may get structurally damaged from the influence of static
electricity. Protect against static electricity and similarly take care when
handling the MOS IC.
Also, keep the receiver of the imager away from debris and intense light.
Note 3: This parts be not reused. Be sure to replace them with new parts.
Ref. No. Part No. Description Ref. No. Part No. Description
551 459775001 IM IMAGER FIX SHAFT (5300) 558 468511801 AS GRAPHITE SHEET IMG (5300) (Note 3)
552 455838602 IM PLATE (5000), GLASS RETAINER 559 472546801 IM SHIELD SHEET (5400)
553 457543001 IM MASK PLATE (5100) 560 468563602 IM RADIATION SHEET B (5300)
554 A5010485A SERVICE OPTFLTRBLK (OFB-01-122)
(Optical Filter Block) (Note 1) 561 468563502 IM RADIATION SHEET A (5300)
555 457676102 SHEET (5100), SPACER 562 468844802 IM RADIATION SHEET C (5300)
563 A2166305A TEX-5300
556 198242411 ISL-2009 FLEXIBLE BOARD 564 468511701 AS GRAPHITE SHEET BTM (5300) (Note 3)
557 198242511 ISP-2008 FLEXIBLE BOARD
3-12
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
614
not supplied
613
611
610
604
not supplied
not supplied
602
609
608
605
607
606
605
603
602
front side
601
(Note)
Ref. No. Part No. Description Ref. No. Part No. Description
601 418853601 CAP, BODY (Note) 608 469289502 MB F PREVENTION SHEET (5300)
602 469263201 SCREW, 0+P1 M2X6 (SPIN) 609 474836601 MB N HOLDER A (5600)
603 468819002 MB N PLATE A (5300) 610 474835501 MB LL BUTTON (5600)
604 474836301 MB N PLATE SP1 (5600)
605 474836401 MB N PLATE SP2 (5600) 611 468817502 MB LL PIN (5300)
612 474836701 MB LL BUTTON SPRING (5600)
606 309148131 SCREW (M1.7 X 4.0) 613 469393001 MB LENS LOCK SPRING (5300)
607 X25946112 MB N CONTACT UNIT (5300) 614 455837202 MB MASK SHEET TAPE (5000)
(including FP-2402 flexible board) 615 457553502 MB MASK SHEET (5100)
3-13E
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
4. SUPPLIED ACCESSORIES
Note:
• Items marked “*” are not stocked since they The components identified by mark 0 or Les composants identifiés par une
are seldom required for routine service. Some dotted line with mark are critical for safety. marque 0 sont critiques pour la sécurité.
delay should be anticipated when ordering Replace only with part number specified. Ne les remplacer que par une pièce por-
these items. tant le numéro spécifié.
Ref. No. Part No. Description Ref. No. Part No. Description
* 500732511 MANUAL, INSTRUCTION (ENGLISH) 0 902 183742814 Power cord (mains lead) (KR)
(ILCE-7RM4)
* 500732521 MANUAL, INSTRUCTION (FRENCH) (ILCE-7RM4) 0 902 183870512 Power cord (mains lead) (CH)
* 500732531 MANUAL, INSTRUCTION 0 902 184608911 Power cord (mains lead) (JE)
(SPANISH, PORTUGUESE) (ILCE-7RM4) 0 902 184609512 Power cord (mains lead) (E: PAL) (Note)
* 500732541 MANUAL, INSTRUCTION (ENGLISH, FRENCH, 0 902 184642011 Power cord (mains lead)
GERMAN, SPANISH, DUTCH, SWEDISH, (AEP, UK, RU, E: PAL, AF) (Note)
ITALIAN, PORTUGUESE, DANISH, FINNISH, 0 902 184642513 Power cord (mains lead) (US, CND)
NORWEGIAN, POLISH, RUSSIAN, UKRAINIAN)
(ILCE-7RM4) 0 902 184643113 Power cord (mains lead) (E: NTSC)
* 500732551 MANUAL, INSTRUCTION 0 902 184806613 Power cord (mains lead) (IND)
(TRADITIONAL CHINESE, SIMPLIFIED CHINESE) 0 903 802663103 Rechargeable battery pack (NP-FZ100-JCE)
(ILCE-7RM4) (AEP, UK, RU, E: PAL, E: NTSC, JE, KR, IND, AF)
0 903 802663130 Rechargeable battery pack (NP-FZ100-UC)
* 500732561 MANUAL, INSTRUCTION (ARABIC, PERSIAN) (US, CND)
(ILCE-7RM4) 0 903 802663175 Rechargeable battery pack (NP-FZ100-CN1) (CH)
* 500732571 MANUAL, INSTRUCTION (KOREAN) (ILCE-7RM4)
* 500732581 MANUAL, INSTRUCTION (SIMPLIFIED CHINESE) 904 191235811 USB Type-C cable
(ILCE-7RM4) 905 501097701 Shoulder strap
* 500732591 MANUAL, INSTRUCTION (FRENCH, RUSSIAN) 906 418853601 Body cap
(ILCE-7RM4) 907 X50002761 Cable protector
* 500732611 MANUAL, INSTRUCTION (HUNGARIAN) 908 443873403 Shoe cap
(ILCE-7RM4)
909 X25945931 Eyepiece cup
* 500732621 MANUAL, INSTRUCTION (SLOVAK) (ILCE-7RM4) 0 910 156900731 Conversion (2P) Adaptor (E: NTSC, JE)
* 500732631 MANUAL, INSTRUCTION (CZECH) (ILCE-7RM4)
* 500732641 MANUAL, INSTRUCTION (THAI) (ILCE-7RM4)
901 902 903
* 500732651 MANUAL, INSTRUCTION (INDONESIAN)
(ILCE-7RM4)
* 502720411 MANUAL, INSTRUCTION (ENGLISH)
(ILCE-7RM4A)
4-1E
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
5. CLEANING
Adhesive side
5-1E
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
6. ADJUSTMENT
For adjusting this models, the Adjust manual and the Adjust station
are required.
Adjust station
It is the software to start up Adjust manual for each model.
The installer of the Adjust station and the installation manual are
attached, be sure to confirm the contents of them.
Adjust manual
It is the software to adjust and check digital cameras and camcord-
ers for service.
The installer of the Adjust manual and the installation manual are
attached, be sure to confirm the contents of them.
6-1E
SYS SET
2022/04/14 12:31:19 (GMT+09:00)
ILCE-7RM4/7RM4A
Revision History
Ver. Date History Contents
SYS SET