Professional Documents
Culture Documents
Polyfoam SS45
Polyfoam SS45
Polyfoam SS45
CHARACTERISTICS
► Spray applied
► CFC free
► 43-48 Density
DESCRIPTION
Polyfoam SS 45 is a two-component, spray-applied polyurethane
foam that creates a seamless, monolithic barrier against water
vapor and air. Polyfoam SS 45 is an HCFC blown & CFC free,
polymeric M.D.I based system for producing rigid urethane foam
with a nominal applied density of 45 kg/m3 by spray process.
The system may be applied to substrates where the surface
temperature is of the order of 25 - 30°C. Grades, adjusted in
reactivity, are available for both cold and hot condition. 1
FIELDS OF APPLICATION warming the entire contents for a short time to a maximum of
70ºC. Polyol might store at room temperature (below 25°C.) in
– Roof spraying applications
sealed drums. Close all drums after use to prevent absorption of
– Flooring and wall insulation moisture.
– Storage tank insulation Safety goggles, impermeable protective gloves and overalls
Component Properties should always be worn when handling this product.
Contaminated clothing should be removed immediately to
MDI component is a dark brown colored, polymeric diphenyl prevent further skin contact.
methane di-isocyanate (crude M.D.I).
– Viscosity @ 20ºC. : 150 - 200 cps Mix ratio
– Specific Gravity @ 20ºC 1.24 1:1 by volume.
– NCO content, % wt. 30-31 Typical reaction rate and density (laboratory, cup mix) (both
Polyol component is a low viscosity blend of polyols, components at 20°C)
hydrochlorofluorocarbon blowing agent, catalysts and surfactant – Cream Time: 3 - 6 sec.
– Viscosity @ 20°C approx.450 cps. – Tack Free Time: 7 - 9 sec.
– Specific Gravity @ 20°C: 1.16 – Free Rise Density: 36 – 38 Kg/m3
Storage and Handling Reactivity and density may vary depend on ambient
temperature and grade.
Store at room temperature in sealed drums. Moisture will react
with this component to produce a surface skin of polymerized SUPPLY
material. Protect from moisture and moisture vapor. Close all
PU Foam SS45
drums after use. Maximum permissible storage time is 6 months.
The ideal storage temperature is between +20ºC and +25ºC. Part A 220kg drum
MDI may undergo partial crystallization at temperature below Part B (MDI) 250kg drum
0ºC. The product can, however, be brought back into the liquid
state by placing the container in a heating cabinet and carefully
429
TECHNICAL SPECIFICATION
PROPERTIES Values Standards
Mix ratio, [volume:volume] 1:1 -
Final density, [kg/m] 43 to 48 ASTM D 1622
Application thickness, [cm]
Min 3
Max 10
Compressive strength, [kpa]
With rise 220 to 320 ASTM D 1621
Against rise 172 to 207
Thermal conductivity @ 25ºC, W/(mk)
Initial value 0.023 ASTM C 518/19
Aged value 0.026
Closed cell content, apparent vol, % 92 to 93 ASTM D 2856
Water vapor transmission, perm-inch
All cut surfaces 2 ASTM C 518/91
With skin retained 1
Water absorption, per cm2 (gm/cc)
Without protective coating 0.0087 ASTM C 272
With protective coating 0.0019
Dimensional stability, % linear change
TDS_PU Foam SS45_GCC_1222
Apart from the information given here it is also important to observe the relevant guidelines and regulations of various organisations and trade associations as well as the
respective standards. The aforementioned characteristics are based on practical experience and applied testing. Warranted properties and possible uses which go beyond
those warranted in this information sheet require our written confirmation. All data given was obtained at an ambient and material temperature of +23°C and 50 %
relative air humidity at laboratory conditions unless specified otherwise. Please note that under other climatic conditions hardening can be accelerated or delayed.
The information contained herein, particularly recommendations for the handling and use of our products, is based on our professional experience. As materials and
conditions may vary with each intended application, and thus are beyond our sphere of influence, we strongly recommend that in each case sufficient tests are conducted
to check the suitability of our products for their intended use. Legal liability cannot be accepted on the basis of the contents of this data sheet or any verbal advice given,
unless there is a case of wilful misconduct or gross negligence on our part. This technical data sheet supersedes all previous editions relevant to this product.
CHARACTERISTICS
► Diphenylmethane – 4,4’- diisocyanate
thermal
insulation
TDS_Polyfoam MDI_GCC_0519
DESCRIPTION
Polyfoam - MDI is a liquid, dark brown mixture of
diphenylmethane – 4,4’- diisocyanate with isomers and
homologues of higher functionality. It is used in conjunction
with polyol to produce rigid polyurethane foams.
FIELDS OF APPLICATION
– it is used in conjunction with polyol to produce rigid
polyurethane foams.
1
STORAGE & HANDLING
Recommended storage temperature: + 10 to + 30°C.
Storage stability (ex works): 6 months if stored in moisture –
production method used, isocyanates based on MDI always
tight drums.
contain phenyl isocyanate (max. 50 ppm), but this has
APPLICATION INSTRUCTIONS practically no effect on the toxicological properties of MDI.
MDI may undergo partial crystallization at temperatures MDI is classified as a dangerous substance and requires
below 0°C. The product can, however, be brought back a hazard-warning label. It must be handled with care. An
into the liquid state by heating the entire contents of the occupational exposure limit has been set which defines
drum for a short time to a maximum of 70°C, although the maximum permissible workplace concentration, in the
this may lead to an increase in the solids content. Drums form of gas, vapour or airborne particulate, of a specific
– including empty ones – should always be kept tightly chemical or chemicals contained in MDI. Details of the
sealed. The product should never be allowed to come current occupational exposure limit, which is subject
into contact with water, which reacts with MDI to form to constant review, are given in the Safety Data Sheet
polyureas and carbon dioxide. Contact with water in any accompanying the product.
form (damp drums, solvents containing water, moist air) The degree of risk depends mainly on the quantities of
must be prevented not only during storage, but also when isocyanate vapours and aerosols released when MDI is
removing material from drums and during processing. processed. No problems arise when MDI is poured at 20
Failure to do so may lead to a dangerous build – up of to 25°C, provided this is done in a well-ventilated area. It is
pressure in tanks and drums due to the generation of however essential to provide adequate exhaust ventilation
carbon dioxide. In addition, polyureas forming in MDI can at each workplace, with the air being drawn away from the
cause solids to separate out, leading to blockages in the personnel handling the product. Exhaust equipment should
filters, pumps and pipelines of the processing equipment be periodically checked.
and resulting in production problems. MDI is a mixture of Ventilation is particularly important if MDI or reaction
diphenylmethane-4,4’-diisocyanate isomers with a specific mixtures containing MDI are sprayed, heated or processed
content of homologues of higher functionality. At 20°C MDI at temperatures above 25°C, since there is then a risk that
has a vapour pressure of less than 10¯5 mbar. Due to the the occupational exposure limit may be exceeded.
Vapours and aerosols of MDI (the latter being formed TECHNICAL SPECIFICATION
during spray application or when cleaning mixing heads
PROPERTIES VALUES
with an air blast) cause irritation to the eyes and the
mucous membranes of the nose, throat and lungs, and Appearance Dark brown liquid
may lead to hypersensitivity reactions. Inhalation should Specific gravity at 25[°C] 1.22-1.25
therefore be avoided. Viscosity at 25[°C] 150-250 mPa.S
Safely goggles, impermeable protective gloves and NCO% Wt 30.2-32.0
overalls fastened at neck and wrist should always be
Acid content(HCL) <0.05%
worn when handling MDI. Splashes of MDI in the eyes
should be removed immediately by careful flushing with Hydrolysable chlorine <0.2%
copious amounts of water. Medical attention should then
be obtained. Splashes on the skin should be wiped off Apart from the information given here it is also important to observe the relevant
immediately, after which the contaminated areas should be guidelines and regulations of various organisations and trade associations as
well as the respective standards. The aforementioned characteristics are based
thoroughly washed with soap and water. A barrier cream on practical experience and applied testing. Warranted properties and possible
should than be applied. Contaminated clothing should be uses which go beyond those warranted in this information sheet require our
removed immediately to prevent further skin contact. MDI written confirmation. All data given was obtained at an ambient and material
temperature of +23°C and 50 % relative air humidity at laboratory conditions
should be kept away from food, drink and tobacco. unless specified otherwise. Please note that under other climatic conditions
hardening can be accelerated or delayed.
The information contained herein, particularly recommendations for the
handling and use of our products, is based on our professional experience.
As materials and conditions may vary with each intended application, and
thus are beyond our sphere of influence, we strongly recommend that in each
case sufficient tests are conducted to check the suitability of our products
for their intended use. Legal liability cannot be accepted on the basis of the
contents of this data sheet or any verbal advice given, unless there is a case
TDS_Polyfoam MDI_GCC_0519
of wilful misconduct or gross negligence on our part. This technical data sheet
supersedes all previous editions relevant to this product.
Page 1 of 2
METHOD STATEMENT
POLYFOAM SS 45
The surface should be free of any cement laitance, oil, grease, curing compound and any other
deleterious materials.
Light mechanical grinding / grit blasting / high pressure water jet may be used to clean the surface
to be coated, based on the degree of contamination.
Nail heads and other protrusions must be removed or ground.
Structurally unsound and friable concrete must be removed and repaired. Honey combed or spalled
concrete, surface irregularities, blow holes to be repaired with a suitable POLYCRETE concrete
repair mortar.
Covering the parapet wall and other utilities fixed on the roof to avoid the risk of overspray.
MS_Polyfoam SS 45_GCC_0323_GR0
Page 2 of 2
Polyfoam SS 45
Sprayed Polyfoam SS 45 is a combination of isocyanate and polyol. These two components feed
through a proportioner, heats & pumps two separate components to the spray gun, where they mixed
and sprayed in to the substrate. Sprayed to the roof as a liquid and forms a single continuous structure
which is seamless and very stable.
Mixing method: Machine mixing
Mixing ratio: 1Polyol :1MDI (by volume)
Adjust the mix ratio 1:1 (by volume) of polyol and MDI, spray to the designated areas by using the
machine. We recommend spraying each layer with 1cm thickness to maintain adequate properties of
the foam.
A protective elastomeric topcoat is required which may be applied by brush, roller or squeegee.
Safety Data Sheet according to Regulation (EC) No 1907/2006
Page 1 of 14
SDS No. : 563844
POLYFOAM MDI (250KG/DRUM) V001.1
Revision: 02.01.2019
printing date: 22.09.2020
Replaces version from: 02.01.2019
Utd.Arab.Emir.
psra.imea@henkel.com
HAAD Poison and Drug Information Center UAE, TOLL FREE TEL. NUMBER 800-424
Classification (CLP):
Acute toxicity Category 4
H332 Harmful if inhaled.
Route of Exposure: Inhalation
Skin irritation Category 2
H315 Causes skin irritation.
Serious eye irritation Category 2
H319 Causes serious eye irritation.
Respiratory sensitizer Category 1
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
Skin sensitizer Category 1
H317 May cause an allergic skin reaction.
Carcinogenicity Category 2
H351 Suspected of causing cancer.
Specific target organ toxicity - single exposure Category 3
H335 May cause respiratory irritation.
Target organ: respiratory tract irritation
Specific target organ toxicity - repeated exposure Category 2
H373 May cause damage to organs through prolonged or repeated exposure.
Hazard pictogram:
For full text of the H - statements and other abbreviations see section 16 "Other information".
Substances without classification may have community workplace exposure limits available.
For full text of the R-Phrases indicated by codes see section 16 'Other Information'.
Substances without classification may have community workplace exposure limits available.
General information:
In case of adverse health effects seek medical advice.
Inhalation:
Move to fresh air, consult doctor if complaint persists.
Delayed effects possible after inhalation.
Skin contact:
Fresh foam : Wipe off affected skin area immediately with a soft cloth and then remove residues with vegetable oil; apply
skin care product. Cured foam can be removed only mechanically.
SDS No.: 563844 V001.1 POLYFOAM MDI (250KG/DRUM) Page 4 of 14
Eye contact:
Immediately flush eyes with soft jet of water or eye rinse solution for at least 5 minutes. If pains remain (intensive smarting,
sensitivity to light, visual disturbance) continue flushing and contact/seek doctor or hospital.
Ingestion:
Rinse mouth and throat. Drink 1-2 glasses of water. Seek medical advice.
4.2. Most important symptoms and effects, both acute and delayed
SKIN: Redness, inflammation.
4.3. Indication of any immediate medical attention and special treatment needed
See section: Description of first aid measures
Hygiene measures:
Wash hands before work breaks and after finishing work.
Do not eat, drink or smoke while working.
Remove any dirt that gets onto the skin with vegetable oil; skin care.
SDS No.: 563844 V001.1 POLYFOAM MDI (250KG/DRUM) Page 5 of 14
Valid for
Utd.Arab.Emir.
Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
4,4'-Methylenediphenyl diisocyanate 0,02 Time Weighted Average DB OEL
9016-87-9 (TWA):
[ISOCYANATES, ALL (AS -NCO)]
4,4'-Methylenediphenyl diisocyanate 0,07 Short Term Exposure DB OEL
9016-87-9 Limit (STEL):
[ISOCYANATES, ALL (AS -NCO)]
4,4'-Methylenediphenyl diisocyanate 0,005 0,051 Time Weighted Average AD TLV
101-68-8 (TWA):
[DIPHENYL METHANE DI
ISOCYANATE [METHYLENE
BISPHENYL ISOCYANATE (MDI)]]
4,4'-Methylenediphenyl diisocyanate 0,07 Short Term Exposure DB OEL
101-68-8 Limit (STEL):
[ISOCYANATES, ALL (AS -NCO)]
4,4'-Methylenediphenyl diisocyanate 0,02 Time Weighted Average DB OEL
101-68-8 (TWA):
[ISOCYANATES, ALL (AS -NCO)]
4,4'-Methylenediphenyl diisocyanate 0,005 0,051 Time Weighted Average GCC TLV
101-68-8 (TWA):
[DIPHENYL METHANE DI
ISOCYANATE]
4,4'-Methylenediphenyl diisocyanate 0,005 0,051 Time Weighted Average UAE OEL
101-68-8 (TWA):
[DIPHENYLMETHANE
DIISOCYANATE]
SDS No.: 563844 V001.1 POLYFOAM MDI (250KG/DRUM) Page 6 of 14
Valid for
Bharain
Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
4,4'-Methylenediphenyl diisocyanate 0,005 0,051 Time Weighted Average BH TLV
101-68-8 (TWA):
[DIPHENYL METHANE
DIISOCYANATE]
4,4'-Methylenediphenyl diisocyanate 0,005 0,051 Time Weighted Average GCC TLV
101-68-8 (TWA):
[DIPHENYL METHANE DI
ISOCYANATE]
Valid for
Egypt
Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
4,4'-Methylenediphenyl diisocyanate 0,005 0,051 Time Weighted Average EG OEL
101-68-8 (TWA):
[METHYLENE BISPHENYL
DIISOCYANATE (MDI)]
Valid for
Jordan
Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
4,4'-Methylenediphenyl diisocyanate 0,02 0,2 Time Weighted Average JO TLV
101-68-8 (TWA):
[DIPHENYLMETHANE
DIISOCYANATE]
Valid for
Kuwait
None
Valid for
Israel
Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
4,4'-Methylenediphenyl diisocyanate 0,005 Time Weighted Average IL OEL
9016-87-9 (TWA):
[ISOCYANATES]
4,4'-Methylenediphenyl diisocyanate 0,0025 Action level (AL): IL OEL
9016-87-9
[ISOCYANATES]
4,4'-Methylenediphenyl diisocyanate 0,02 Short-term exposure limit IL OEL
9016-87-9 (STEL):
[ISOCYANATES]
4,4'-Methylenediphenyl diisocyanate 0,005 Time Weighted Average IL OEL
101-68-8 (TWA):
[METHYLENE BISPHENYL
ISOCYANATE (MDI)]
SDS No.: 563844 V001.1 POLYFOAM MDI (250KG/DRUM) Page 7 of 14
Valid for
Kenya
Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
4,4'-Methylenediphenyl diisocyanate 0,07 Short term OEL-CL: KE OEL-CL
9016-87-9
[ISOCYANATES, ALL (AS-NCO)]
4,4'-Methylenediphenyl diisocyanate 0,02 Time-weighted average KE OEL-CL
9016-87-9 (TWA) OEL-CL:
[ISOCYANATES, ALL (AS-NCO)]
4,4'-Methylenediphenyl diisocyanate 0,02 Time-weighted average KE OEL-CL
101-68-8 (TWA) OEL-CL:
[ISOCYANATES, ALL (AS-NCO)]
4,4'-Methylenediphenyl diisocyanate 0,07 Short term OEL-CL: KE OEL-CL
101-68-8
[ISOCYANATES, ALL (AS-NCO)]
4,4'-Methylenediphenyl diisocyanate 0,02 Time-weighted average KE OEL-RL
101-68-8 (TWA) OEL-RL:
[4,4'-METHYLENE-DIPHENYL
DIISOCYANATE (MDI)]
4,4'-Methylenediphenyl diisocyanate 0,07 Short-term OEL-RL: KE OEL-RL
101-68-8
[4,4'-METHYLENE-DIPHENYL
DIISOCYANATE (MDI)]
Respiratory protection:
Suitable breathing mask when there is inadequate ventilation.
Combination filter: ABEKP (EN 14387)
This recommendation should be matched to local conditions.
SDS No.: 563844 V001.1 POLYFOAM MDI (250KG/DRUM) Page 9 of 14
Hand protection:
In the case of longer contact protective gloves made from nitrile rubber are recommended according to EN 374.
Perforation time > 60 minutes
material thickness > 0.1 mm
In the case of longer and repeated contact please note that in practice the penetration times may be considerably shorter than
those determined according to EN 374. The protective gloves must always be checked for their suitability for use at the
specific workplace (e.g. mechanical and thermal stress, product compatibility, antistatic effects, etc.). The gloves must be
replaced immediately at the first signs of wear and tear. The information provided by the manufacturers and given in the
relevant trade association regulations for industrial safety must always be observed. We recommend that a hand care plan is
drawn up in cooperation with a glove manufacturer and the trade association in accordance with the local operating
conditions.
Eye protection:
Goggles which can be tightly sealed.
Protective eye equipment should conform to EN166.
Skin protection:
Suitable protective clothing
Protective clothing should conform to EN 14605 for liquid splashes or to EN 13982 for dusts.
Skin corrosion/irritation:
Carcinogenicity:
12.1. Toxicity
No data available.
SDS No.: 563844 V001.1 POLYFOAM MDI (250KG/DRUM) Page 13 of 14
Waste code
08 05 01
14.1. UN number
14.7. Transport in bulk according to Annex II of Marpol and the IBC Code
not applicable
15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
VOC content 0%
(VOCV 814.018 VOC regulation
CH)
Further information:
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is
intended to describe our products from the point of view of safety requirements and is not intended to guarantee any
particular properties.
This Safety Data Sheet has been generated based on Regulation (EC) No 1907/2006 and it is applicable for Gulf Cooperation
Council (GCC) and Africa only. No warranty or representation of any kind is given as to compliance with any statutory laws
or regulations of any other jurisdiction or territory, including export laws and regulations. Please confirm that the information
provided herein conforms to the substantive export or other law of any other jurisdiction prior to export. Please contact
Henkel Product Safety and Regulatory affairs for additional assistance.
Relevant changes in this safety data sheet are indicated by vertical lines at the left margin in the body of this document.
Corresponding text is displayed in a different color on shadowed fields.
Safety Data Sheet according to (EC) No 1907/2006 as amended
Page 1 of 16
HAAD Poison and Drug Information Center UAE, TOLL FREE TEL. NUM BER 800-424
Classification (CLP):
Chronic hazards to the aquatic environment Category 3
H412 Harmful to aquatic life with long lasting effects.
Hazardous to the ozone layer Category 1
H420 Harms public health and the environment by destroying ozone in the upper atmosphere.
Hazard pictogram:
Hazard statement: H412 Harmful to aquatic life with long lasting effects.
H420 Harms public health and the environment by destroying ozone in the upper
atmosphere.
Safety Data Sheet according to (EC) No 1907/2006 as amended
Precautionary statement: P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
For full text of the H - statements and other abbreviations see section 16 "Other information".
S ubstances without classification may have community workplace exposure limits available.
General information:
In case of adverse health effects seek medical advice.
Safety Data Sheet according to (EC) No 1907/2006 as amended
Inhalation:
M ove to fresh air, consult doctor if complaint persists.
Skin contact:
Rinse with running water and soap. Skin care. Remove contaminated clothes immediately.
Eye contact:
Immediately flush eyes with soft jet of water or eye rinse solution for at least 5 minutes. If pains remain (intensive smarting,
sensitivity to light, visual disturbance) continue flushing and contact/seek doctor or hospital.
Ingestion:
Rinse mouth and throat. Drink 1-2 glasses of water. Seek medical advice.
4.2. Most important symptoms and effects, both acute and delayed
No data available.
4.3. Indication of any immediate medical attention and special treatment needed
See section: Description of first aid measures
Hygiene measures:
Wash hands before work breaks and after finishing work.
Do not eat, drink or smoke while working.
Valid for
Utd.Arab.Emir.
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate 0,1 T ime Weighted Average AD T LV
77-58-7 (T WA):
[T IN ORGANIC COMPOUNDS, AS SN]
Dibutyltin dilaurate 0,2 Short T erm Exposure AD T LV
77-58-7 Limit (ST EL):
[T IN ORGANIC COMPOUNDS, AS SN]
Dibutyltin dilaurate Skin designation: Can be absorbed through the AD T LV
77-58-7 skin.
[T IN ORGANIC COMPOUNDS, AS SN]
Dibutyltin dilaurate Skin designation: Can be absorbed through the GCC T LV
77-58-7 skin.
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,2 Short T erm Exposure GCC T LV
77-58-7 Limit (ST EL):
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,1 T ime Weighted Average GCC T LV
77-58-7 (T WA):
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,1 T ime Weighted Average UAE OEL
77-58-7 (T WA):
[T IN, ORGANIC COMPOUNDS (AS SN)]
Dibutyltin dilaurate 0,2 Short T erm Exposure UAE OEL
77-58-7 Limit (ST EL):
[T IN, ORGANIC COMPOUNDS (AS SN)]
Dibutyltin dilaurate Skin designation: Can be absorbed through the UAE OEL
77-58-7 skin.
[T IN, ORGANIC COMPOUNDS (AS SN)]
Safety Data Sheet according to (EC) No 1907/2006 as amended
Valid for
Bharain
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate 0,2 Short T erm Exposure BH T LV
77-58-7 Limit (ST EL):
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate Skin designation: Can be absorbed through the BH T LV
77-58-7 skin.
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,1 T ime Weighted Average BH T LV
77-58-7 (T WA):
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate Skin designation: Can be absorbed through the GCC T LV
77-58-7 skin.
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,2 Short T erm Exposure GCC T LV
77-58-7 Limit (ST EL):
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,1 T ime Weighted Average GCC T LV
77-58-7 (T WA):
[T IN (ORGANIC COMPOUNDS AS SN)]
Valid for
Egypt
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate 0,1 T ime Weighted Average EG OEL
77-58-7 (T WA):
[T IN ORGANIC COMPOUNDS (AS SN)]
Valid for
Jordan
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate 0,1 T ime Weighted Average JO T LV
77-58-7 (T WA):
[T IN (ITS COMPOUNDS)]
Dibutyltin dilaurate Skin designation: Can be absorbed through the JO T LV
77-58-7 skin.
[T IN (ITS COMPOUNDS)]
Valid for
Kuwait
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate Skin designation: Can be absorbed through the GCC T LV
77-58-7 skin.
[T IN (ORGANIC COMPOUNDS AS SN)]
Dibutyltin dilaurate 0,2 Short T erm Exposure GCC T LV
77-58-7 Limit (ST EL):
[T IN (ORGANIC COMPOUNDS AS SN)]
Safety Data Sheet according to (EC) No 1907/2006 as amended
Valid for
Israel
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate 0,2 Short-term exposure limit IL OEL
77-58-7 (ST EL):
[T IN, ORGANIC COMPOUNDS, AS SN]
Dibutyltin dilaurate 0,1 T ime Weighted Average IL OEL
77-58-7 (T WA):
[T IN, ORGANIC COMPOUNDS, AS SN]
Dibutyltin dilaurate Skin designation: Danger of cutaneous IL OEL
77-58-7 absorption
[T IN, ORGANIC COMPOUNDS, AS SN]
Valid for
Kenya
Ingre dient [Regulated substance] ppm mg/m 3 Value type Short term exposure limit Re gulatory list
category / Remarks
Dibutyltin dilaurate 0,2 Short-term OEL-RL: KE OEL-RL
77-58-7
[T IN COMPOUNDS, ORGANIC, EXCEPT
CYHEXAT IN (ISO), (AS SN)]
Dibutyltin dilaurate 0,1 T ime-weighted average KE OEL-RL
77-58-7 (T WA) OEL-RL:
[T IN COMPOUNDS, ORGANIC, EXCEPT
CYHEXAT IN (ISO), (AS SN)]
Dibutyltin dilaurate Skin designation: Can be absorbed through the KE OEL-RL
77-58-7 skin.
[T IN COMPOUNDS, ORGANIC, EXCEPT
CYHEXAT IN (ISO), (AS SN)]
Respiratory protection:
The product should only be used at workplaces with intensive ventilation/extraction. If intensive ventilation/extraction is not
possible then self-contained independent respiratory protection should be worn.
Safety Data Sheet according to (EC) No 1907/2006 as amended
Hand protection:
Recommended are gloves made from Nitril rubber ( M aterial thickness >0,1 mm, Perforation time < 30s).Gloves should be
replaced after each short time contact or contamination. Available at laboratory specialized trade or at pharmacies / chemist 's
shops.
In the case of longer contact protective gloves made from nitrile rubber are recommended according to EN 374.
Perforation time > 30 minutes
material thickness > 0.4 mm
In the case of longer and repeated contact please note that in practice the penetration times may be considerably shorter than
those determined according to EN 374. The protective gloves must always be checked for their suitability for use at the
specific workplace (e.g. mechanical and thermal stress, product compatibility, antistatic effects, etc.). The gloves must be
replaced immediately at the first signs of wear and tear. The information provided by the manufacturers and given in the
relevant trade association regulations for industrial safety must always be observed. We recommend that a hand care plan is
drawn up in cooperation with a glove manufacturer and the trade association in accordance with the local operating
conditions.
Eye protection:
Goggles which can be tightly sealed.
Protective eye equipment should conform to EN166.
Skin protection:
Suitable protective clothing
Protective clothing should conform to EN 14605 for liquid splashes or to EN 13982 for dusts.
S TOT-repeated exposure:
M ay cause damage to organs through prolonged or repeated exposure.
S kin corrosion/irritation:
12.1. Toxicity
Ecotoxicity:
Harmful to aquatic life with long lasting effects.
Safety Data Sheet according to (EC) No 1907/2006 as amended
T ris(2-chloro-1-methylethyl) phosphate Not fulfilling Persistent, Bioaccumulative and T oxic (PBT), very Persistent and very
13674-84-5 Bioaccumulative (vPvB) criteria.
2-Dimethylaminoethanol Not fulfilling Persistent, Bioaccumulative and T oxic (PBT), very Persistent and very
108-01-0 Bioaccumulative (vPvB) criteria.
Cyclohexyldimethylamine Not fulfilling Persistent, Bioaccumulative and T oxic (PBT), very Persistent and very
98-94-2 Bioaccumulative (vPvB) criteria.
dibutyltin dilaurate Not fulfilling Persistent, Bioaccumulative and T oxic (PBT), very Persistent and very
77-58-7 Bioaccumulative (vPvB) criteria.
No data available.
Waste code
080409
Safety Data Sheet according to (EC) No 1907/2006 as amended
14.1. UN number
14.7. Transport in bulk according to Annex II of Marpol and the IBC Code
not applicable
Safety Data Sheet according to (EC) No 1907/2006 as amended
15.1. S afety, health and environmental regulations/legislation specific for the substance or mixture
No information available:
Further information:
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is
intended to describe our products from the point of view of safety requirements and is not intended to guarantee any
particular properties.
This Safety Data Sheet has been generated based on Regulation (EC) No 1907/2006 and it is applicable for Gulf Cooperation
Council (GCC) and Africa only. No warranty or representation of any kind is given as to compliance with any statutory laws
or regulations of any other jurisdiction or territory, including export laws and regulations. Please confirm that the information
provided herein conforms to the substantive export or other law of any other jurisdiction prior to export. Please contact
Henkel Product Safety and Regulatory affairs for additional assistance.
Dear Customer,
Henkel is committed to creating a sustainable future by promoting opportunities along the entire value chain. If you would
like to contribute by switching from a paper to the electronic version of SDS, please contact the local Customer Service
representative. We recommend to use a non-personal email address (e.g. SDS@your_company.com).
Relevant changes in this safety data sheet are indicated by vertical lines at the left margin in the body of this document.
Corresponding text is displayed in a different color on shadowed fields.
التاريخ2022/01/24 :م
املرجع11/122/2022 :
كما يرجى العلم بأن بلدية مدينة الشارقة لن تتحمل مسؤولية أي عواقب تترتب على هذه املوافقة ،عليه يجب التحقق من كل تقديم أو
مقترح ملشروع قبل مباشرة مواصفات كل مشروع.
ملزيد من االستفسارات ،التواصل مع املهندس /بالل جوس رقم هاتف ( )05516600020بإدارة الصرف الصحي
-
Al Mazrouei Building - Project Name : Commercial Building (2B+G+7F+R) Al Mazrouei for Mr.
TITLE:
Salhan Mohamed Salham Al Mazrouei & Heirs Daafoos Mohamed Salhan Al Mazrouei
TO BE REVIEWED BY: EC
ECOBUILD
TYPE OF SUBMITTAL: Ma
Material Submittal Material
M
Ma Sample Me
Method Statement
Pre-Qualification
P
Pr Re
Reports Operational
Op Procedures
Operational Maintenance
Op enance Manual Ot
Others:
t
DISCIPLINE: Ar
Architectural ME
MEP He
Health & Safety
Structural
St Ci
Civil Ot
Others:
Specs.:
REVIEW COMMENTS
Estidama PQP Review:
кͨΖχϚϋϘϏχϒϝχϙϘϋϜϏϋϝϋϊχύχϏϔϙϚΜΖΛкΎϙϚϏϊχϓχωϘϋϊϏϚχϔϊϏϙόϕϛϔϊϚϕψϋωϕϓϖϒϏχϔϚͨ
лͨΝώϋϘϓχϒωϕϔϊϛωϚϏϜϏϚϟόϕϘϚώϋϖϘϕϜϏϊϋϊωϕϓψϕϘϕϕόϏϔϙϛϒχϚϏϕϔϏϙχϖϖϘϕϜϋϊͨ
мͨΌϕϔϚϘχωϚϕϘϚϕϖϘϕϜϏϊϋϊϋϒϏϜϋϘϟϔϕϚϋϛϖϕϔϓχϚϋϘϏχϒϊϋϒϏϜϋϘϟͨ
нͨΌϕϔϚϘχωϚϕϘϚϕϖϘϕϜϏϊϋϖώϕϚϕύϘχϖώϏωϋϜϏϊϋϔωϋϛϖϕϔϏϔϙϚχϒϒχϚϏϕϔͨ
ICA Review:
A- Approved
A B- Approved
B C- N
C No Objection
Obj
bjec
e tion D- Revise
D E- Rejected
E
with Comments
wit and Resubmit
Avan Pasha (PQP) Signature: Date: 25-07-2022
Al Mazrouei Building - Project Name : Commercial Building (2B+G+7F+R) Al Mazrouei for Mr.
TITLE:
Salhan Mohamed Salham Al Mazrouei & Heirs Daafoos Mohamed Salhan Al Mazrouei
TO BE REVIEWED BY: EC
ECOBUILD
TYPE OF SUBMITTAL: Ma
Material Submittal Material
M
Ma Sample Me
Method Statement
Pre-Qualification
P
Pr Re
Reports Operational
Op Procedures
Operational Maintenance
Op enance Manual Ot
Others:
t
DISCIPLINE: Ar
Architectural ME
MEP He
Health & Safety
Structural
St Ci
Civil Ot
Others:
Specs.:
REVIEW COMMENTS
Estidama PQP Review:
кͨΖχϚϋϘϏχϒϝχϙϘϋϜϏϋϝϋϊχύχϏϔϙϚΜΖΛкΎϙϚϏϊχϓχωϘϋϊϏϚχϔϊϏϙόϕϛϔϊϚϕψϋωϕϓϖϒϏχϔϚͨ
лͨΝώϋϘϓχϒωϕϔϊϛωϚϏϜϏϚϟόϕϘϚώϋϖϘϕϜϏϊϋϊωϕϓψϕϘϕϕόϏϔϙϛϒχϚϏϕϔϏϙχϖϖϘϕϜϋϊͨ
мͨΌϕϔϚϘχωϚϕϘϚϕϖϘϕϜϏϊϋϊϋϒϏϜϋϘϟϔϕϚϋϛϖϕϔϓχϚϋϘϏχϒϊϋϒϏϜϋϘϟͨ
нͨΌϕϔϚϘχωϚϕϘϚϕϖϘϕϜϏϊϋϖώϕϚϕύϘχϖώϏωϋϜϏϊϋϔωϋϛϖϕϔϏϔϙϚχϒϒχϚϏϕϔͨ
ICA Review:
A- Approved
A B- Approved
B C- N
C No Objection
Obj
bjec
e tion D- Revise
D E- Rejected
E
with Comments
wit and Resubmit
Avan Pasha (PQP) Signature: Date: 25-07-2022
License Details
License Number 107
Address Details
Lease Contract Number TC - 29962
Property Owner Ahmed Mohamed Salim
Almelaihi Al-Ali
Region Umm Thaob 7 7
Street undefined
Telephone 0508919999 Mobile 0508919999
P.O.Box 0000909 Email ahmed@linkrealestate.ae
License Members
49%
Partner Germany Henkel KGAA company
0%
Manager Netherlands HARM PETRUS ANTONIUS PETERS
"http://ded-e.uaq.ae"
Page 1/2 TEL +971 6 7064000 * UMM AL QUAIN, UAE * P.O.BOX 1333 .
Activities
Retail Sale Of Cosmetics -
Caulking Compounds and Similar Manufacturing
Fire Extinguishing Materials Manufacturing
Cements Prepared Additives Manufacturing
Damp proofing and water proofing works Insulation
Contracting
Wholesale of Cleaners and Detergents Trading -
Beauty and Make-Up Preparations Manufacturing
Wholesale of Cosmetics and Trading -
Retai sale of Buildings Material -
Detergents & Disinfectants Manufacturing
Onshore and Offshore Oil and Gas Fields and Facilities
Services
"http://ded-e.uaq.ae"
Page 2/2 TEL +971 6 7064000 * UMM AL QUAIN, UAE * P.O.BOX 1333 .
Commercial License ﺭﺧـﺼــــــﺔ ﺗﺠﺎﺭﻳﺔ
Emerging Economic Establishment ﻣﻨﺸــــﺄﺓ ﺍﻗﺘﺼـــﺎﺩﻳــــﺔ ﻧﺎﺷﺌـــــــﺔ
www.adbc.gov.ae ﻟﻠﺘﺤﻘﻖ ﻣﻦ ﺻﺤﺔ ﺍﻟﺒﻴﺎﻧﺎﺕ ﺍﻟﻮﺍﺭﺩﺓ ﻓﻲ ﺍﻟﺮﺧﺼﺔ ﺑﺮﺟﺎﺀ ﺯﻳﺎﺭﺓ ﺍﻟﻤﻮﻗﻊ. ﺃﺑﻮﻇﺒﻲ- ﻭﺛﻴﻘﺔ ﻣﻌﺘﻤﺪﺓ ﻭﺻﺎﺩﺭﺓ ﺑﺪﻭﻥ ﺗﻮﻗﻴﻊ ﺃﻭ ﺧﺘﻢ ﻣﻦ ﺩﺍﺋﺮﺓ ﺍﻟﺘﻨﻤﻴﺔ ﺍﻹﻗﺘﺼﺎﺩﻳﺔ
Approved document issued without signature or stamp by the Department of Economic Development - Abu Dhabi. To verify the license kindly
visit www.adbc.gov.ae
Official Email : talalkastali@hotmail.com : ﺍﻟﺒﺮﻳﺪ ﺍﻹﻟﻜﺘﺮﻭﻧﻲ ﺍﻟﺮﺳﻤﻲ
Official Mobile : 971569992018 : ﺭﻗﻢ ﺍﻟﺘﻮﺍﺻﻞ ﺍﻟﺮﺳﻤﻲ
*CR-4478863*
www.adbc.gov.ae
INDUSTRIAL LICENSE ﺭﺧﺼــﺔ ﺻﻨـﺎﻋﻴﺔ
License No IN-2004813 ﺭﻗﻢ ﺍﻟﺮﺧﺼﺔ
Emerging Industrial Establishment ﻣﻨﺸــــﺄﺓ ﺻﻨـــﺎﻋﻴــــــــﺔ ﻧﺎﺷﺌـــــــﺔ
License Status : Industrial Leader ﺭﻭﺍﺩ ﺍﻟﺼﻨﺎﻋﺔ: ﺣﺎﻟﺔ ﺍﻟﺮﺧﺼﺔ
Legal Form : Limited Liability Company ﺷﺮﻛﺔ ﺫﺍﺕ ﻣﺴﺆﻭﻟﻴﺔ ﻣﺤﺪﻭﺩﺓ: ﺍﻟﺸﻜﻞ ﺍﻟﻘﺎﻧﻮﻧﻲ
ADCCI No : : ﻋﻀﻮﻳﺔ ﺍﻟﻐﺮﻓﺔ
First Issue Date 21/12/2021 : ﺗﺎﺭﻳﺦ ﺃﻭﻝ ﺇﺻﺪﺍﺭ Enviroment No. : ﺍﻟﺮﻗﻢ ﺍﻟﺒﻴﺌﻲ
: :
Issue Date : 21/12/2022 : ﺗﺎﺭﻳﺦ ﺍﻹﺻﺪﺍﺭ FCR No. : - : ﺍﻟﺴﺠﻞ ﺍﻟﻤﺮﻛﺰﻱ ﺍﻟﻤﻮﺣﺪ
Expiry Date : 20/12/2023 : ﺗﺎﺭﻳﺦ ﺍﻹﻧﺘﻬﺎﺀ Trade Name No. : TN-4241436 : ﺭﻗﻢ ﺍﻹﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ
2 ﻓﺮﻉ- ﻫﻨﻴﻜﻞ ﺑﻮﻟﻲ ﺑﺖ ﻟﻠﺼﻨﺎﻋﺎﺕ ﺍﻟﻤﺤﺪﻭﺩﺓ ﺫ ﻡ ﻡ : ﺍﻹﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ
Trade Name : Henkel Polybit Industries Limited - Branch Of Abu Dhabi 2
ﺍﻟﺘﺮﺧﻴﺺ ﺻﺎﺩﺭ ﻣﻦ ﻗﺒﻞ ﺳﻠﻄﺔ ﺍﻟﺘﺮﺧﻴﺺ ﺍﻟﻤﺤﻠﻴﺔ ﻓﻲ ﺇﻣﺎﺭﺓ ﺃﺑﻮﻇﺒﻲ ﺧﺎﺭﺝ ﺍﻟﻤﻨﺎﻃﻖ ﺍﻟﺤﺮﺓ
The license is issued by the local licensing authority in the Emirate of Abu Dhabi outside the free zones
IN-2004813 - 23/11/2022
Page1 of 2 TAHAQAQ ﺗﺤﻘﻖ
www.idb.added.gov.ae
Henkel Polybit Industries Ltd.
PO Box: 293, Umm Al Quwain, UAE
Phone: +971 (6) 76 70 777
Fax: +971 (6) 76 70 197
henkelpolybit@henkel.com
www.henkelpolybit.com