Professional Documents
Culture Documents
Exterior: Click On The Applicable Bookmark To Selected The Required Model Year
Exterior: Click On The Applicable Bookmark To Selected The Required Model Year
uk
EXTERIOR
Click on the applicable bookmark to selected the required model year.
EXTERIOR
CONTENTS
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 23
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 28
ADHESIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 31
MARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
FRONT BUMPER
ADHESIVE
Items Specified sealant and adhesive
Front bumper side extension Double-sided tape [5 mm wide and 1.2 mm thick]
SPECIAL TOOL
Tool Number Name Use
MB990784 Ornament remover Front bumper reinforcement assembly
removal
FRONT BUMPER
REMOVAL AND INSTALLATION
Section A – A Section B – B Section C – C
1 2
Clip
2
Clip 6
Clip
A
1
2 A
4
B
B
5
C
4
C
3
6
Removal steps
1. Radiator cover 5. Front bumper lower stay
AA" 2. Radiator grille D Fog lamp connector connection
3. Skid plate 6. Front bumper face assembly
4. Splash shield mounting clip
A
Radiator
grille
Clip
1 9 Clip 2
3
A 5
A
B
4
B C
C
7 View A
D
E D
A
E
8
2
6
Disassembly steps
D Headlamp washer 5. Air duct <LH side in vehicles without
AA" 1. Front bumper reinforcement assembly fog lamps>
2. Fog lamp cover AB" "AA 6. Front bumper side extension
3. Fog lamp 7. Licence plate garnish
4. Air blower garnish <Vehicles without 8. Licence plate bracket
fog lamps> 9. Front bumper face
Pin Clip
REAR BUMPER
REMOVAL AND INSTALLATION
Section A – A Section B – B Section C – C Section D – D
Clip Clip 5
5 3 5
Clip
Clip 1
3
3
C
A
C
4 A D
D 3
1
B
B
2
3
8
4
7
1
Rear bumper side face assembly Rear bumper center face assembly
disassembly steps disassembly steps
AA" "AA 1. Rear mudguard reinforcement 6. Rear bumper step plate
AA" "AA 2. Rear bumper side retainer 7. Rear bumper center face stay
(Short wheelbase) 8. Rear bumper center face
AA" "AA 3. Rear bumper side retainer
(Long wheelbase)
AA" "AA 4. Rear bumper corner bracket
D Rear lamp and rear lamp bracket
(Refer to GROUP 54A.)
5. Rear bumper side face
3 Recommended
tool
Flange
Rivet
ROOF RAIL
ROOF RAIL
REMOVAL AND INSTALLATION
1
4
5
3
5
2
5
Removal steps
D Head lining 2. Roof rail front seal
D Set bracket (Refer to GROUP 42 - 3. Roof rail center seal
Sunroof.) 4. Roof rail rear seal
1. Roof rail assembly 5. Roof rail seal
MOULDING
ADHESIVE
Items Specified sealant and adhesive
Wheel cut moulding and door moulding Double-sided tape [ 4 mm width and 1.2 mm thickness, 12
mm width and 1.2 mm thickness, 5 mm width and 1.2 mm
thicknes.]
SPECIAL TOOL
Tools No. Name Application
MB990449 Window moulding Roof drip moulding removal
remover
MOULDING
REMOVAL AND INSTALLATION
<Vehicles with roof rail> Section A – A Section B – B
A
A
A 8,9 Clip 1,3, Clip
A 4,5
<Vehicles without roof rail>
A
A
A
A
9 <Long wheelbase>
7
4
2 <Short wheelbase>
6
1
B
5 4
B
1 2
B
B B
B
3
B
B
2 B
B
AA" "AA 1. Front door moulding Roof drip moulding removal steps
Front wheel cut moulding removal D Roof rail assembly
steps AC" 8. Roof drip moulding <Short wheel-
AB" "BA 2. Rivet A base>
AA" "AA 3. Front wheel cut moulding AC" 9. Roof drip moulding <Long wheelbase>
Rear wheel cut moulding removal
steps
AB" "BA 2. Rivet A
AA" "AA 4. Rear wheel cut moulding
Rear door moulding removal steps
AB" "BA 2. Rivet A
AA" "AA 5. Rear door moulding
AB" "CA 6. Rivet B
AA" "AA 7. Rear door moulding bracket
A
A
C
Front door moulding
(Short wheelbase)
Adhesive tape: Double-side tape [A: 4 mm width and 1.2 mm thickness, B: 12 mm width and 1.2
mm thickness, C: 5 mm width and 1.2 mm thickness.]
Double-sided tape
Rivet
Moulding
Drill
3 Recommended
tool
Flange
4
Rivet
GARNISH
ADHESIVE
Items Specified sealant and adhesive
Section A – A
1,2, Clip
3,4
2 2
A
A 1
1
A
A
A
A
Side sill garnish removal steps Licence plate garnish removal steps
D Side step D Toolbox bracket, upper (Refer to
D Front mudguard GROUP 42 - Back door trim and
AA" "AA 1. Side sill garnish <Short wheelbase> waterproof film.)
AA" "AA 2. Side sill garnish <Long wheelbase> D Licence lamp (Refer to GROUP 54A.)
3. Licence plate garnish
MUDGUARD
ADHESIVE
Items Specified sealant and adhesive
MUDGUARD
REMOVAL AND INSTALLATION
C 7
A 7
A
4
B
A 5 6
A
3 3
2
1
REAR DEFLECTOR
SPECIAL TOOL
Tools Number Name Use
MB990784 Ornament remover Rear deflector cover removal
REAR DEFLECTOR
REMOVAL AND INSTALLATION
Section A – A
2
3
Tab
1
5.0 ± 1.0 N×m
SIDE STEP
SIDE STEP
REMOVAL AND INSTALLATION
Section A – A
4
1
Tab
A
2
A A
A
Side step removal steps AA" "AA 3. Non-slip cover <Long wheelbase>
AA" "AA 1. Side step cover 4. Side step assembly
AA" "AA 2. Non-slip cover <Short wheelbase>
TROUBLESHOOTING
The windshield wiper and washer is controlled by the SWS (Smart Wiring System). For troubleshooting
procedures, refer to GROUP 54B - SWS Diagnosis.
Tab
C Section C – C
4.9±1.0 N×m C
C 5
7
C 4
6
4 Tab
8.9±1.9 N×m
1 2
8
11 4.9±0.7 N×m
12 10
4.9±0.7 N×m
9
INSPECTION
WINDSHIELD WIPER MOTOR ASSEMBLY CHECK
The windshield wiper motor assembly should be installed
to the vehicle body and the harness connector should be
disconnected when checking the wiper motor.
D Low Speed and High Speed Wiper Motor Operation
Check
Connect the battery to the wiper motor as shown in the
illustration, and then check the operation of the wiper
Check operation
motor at low speed and at high speed.
D Windshield Wiper Motor Assembly Stop Position
Check
1. Connect the battery to the wiper motor as shown
Low speed High speed in illustration (A), and then run the wiper motor at
Stop position check low speed. Then, while the motor is operating,
disconnect the battery to make the wiper motor stop.
2. Connect the terminals and the battery as shown in
illustration (B), and then check whether the wiper
motor automatically stops in the correct stop position
(A)Low speed (B)Automatic stop after it has been running at low speed.
50
105 95 90 100
380
200 295
220
<R.H.drive vehicles>
WINDSHIELD INTERMITTENT WIPER INTERVAL
ADJUSTING KNOB
Measure the resistance value at terminal numbers 4 and
6. The resistance value should rise smoothly from
approximately 0 W (“FAST” position) to apporoximately 1 kW
(“SLOW” position).
NOTE:
Windshield washer and wiper switch is integrated with the
column-ECU, and can not be checked. However, its operation
can be checked by the input signal check. (Refer to GROUP
54B – Troubleshooting.)
TROUBLESHOOTING
The rear wiper and washer is controlled by the SWS (Smart Wiring System). For troubleshooting procedures,
refer to GROUP 54B - SWS Diagnosis.
8.0±1.2 N×m
4.9±0.7 N×m
3 2 6
7
4.9±0.7 N×m
4
4.9±0.7 N×m
Mating marks
Notch
INSPECTION
REAR WIPER MOTOR ASSEMBLY CHECK
The rear wiper motor assembly should be installed to the
vehicle body and the harness connector should be
disconnected when checking the wiper motor.
D Wiper Motor Operation Check
Connect the battery to the wiper motor as shown in the
illustration, and then check the operation of the wiper
motor.
Check operation D Wiper Motor Stop Position Check
1. Operate the wiper motor by the same method as
Battery described in the check procedure above. Then, while
the motor is operating, disconnect the battery to make
the wiper motor stop.
2. Reconnect the battery as shown in the illustration,
Stop position check
and then check whether the wiper motor automatically
stops in the correct stop position after it has been
running.
Battery
95
85
Centre of vehicle
HEADLAMP WASHER
TROUBLESHOOTING
The headlamp washer is controlled by the Smart Wiring System (SWS). For troublesshooting, refer to
GROUP 54B - Troubleshooting.
HEADLAMP WASHER
REMOVAL AND INSTALLATION
3
1
4.9 ± 0.7 N×m
2
1 3
4.9 ± 0.7 N×m
INSPECTION
CHECK VALVE CHECK
Apply pressure to the inlet of the check valve to check its
opening pressure.
Opening pressure: 78 kPa
<L.H.drive vehicles>
Headlamp washer switch is integrated in the column-ECU,
and can not be checked. However, its operation can be
checked by the input signal check. (Refer to GROUP 54B
– Troubleshooting.)
WIPER DEICER
SPECIAL TOOL
Tools No. Name Application
MB990784 Ornament remover Wiper deicer switch removal
1
2
INSPECTION
WIPER DEICER SWITCH CONTINUITY CHECK
Switch Terminal No.
position 1 - 2 3 4 5 - 6
OFF ILL
ON
IND
MARKS
MARKS
REMOVAL AND INSTALLATION
1
2 3
32 mm
90 mm
110 mm 50 mm
45 mm
Caution
1) Carry out this work in a location which has an
ambient temperature of 20 - 38_C and which is
free from dust.
2) If the ambient temperature is lower than 20_C,
heat the mark and the vehicle body (application
location) to 20 - 30_C.
TROUBLESHOOTING
The outside mirrors are controlled by the SWS (Smart Wiring System). For troubleshooting procedures,
refer to GROUP 54B - SWS Diagnosis.
Clip
5
A
B A
B
6
A A
A A
Protective
tape
Notch
A A
A A
INSPECTION
MIRROR ASSEMBLY OPERATION CHECK
Left
Right
Illumination
Service Bulletins
Click on the applicable bookmark to select the Service Bulletin.
INFORMATION INTERNATIONAL
CAR
ADMINISTRATION T.MASAKI-MANAGER
OFFICE TECHNICAL SERVICE PLANNING
1. Description:
The mounting bolts, nuts, and tightening torque values of the side step assembly have been
changed.
2. Applicable Manuals:
Manual Pub. No. Language Page(s)
2001 PAJERO PWJE0001(2/2) (English) 51-22
Workshop Manual Chassis
2001 MONTERO PWJS0002(2/2) (Spanish)
Workshop Manual Chassis
2001 PAJERO/MONTERO PWJT0008R (English)
Workshop Manual Chassis CD-ROM PWJT0008R (Spanish)
PWJT0008R (French)
PWJT0008R (German)
3. Effective date:
From August 2, 2000
SIDE STEP
SIDE STEP
REMOVAL AND INSTALLATION
Section A-A
Tab
AX1070CA
AX0776CA
AY0455CA
TROUBLESHOOTING
TROUBLE SYMPTOM CHART
Trouble symptom Inspection Reference
procedure page
Both of the electric retractable door mirrors do not work at all. 1 51-2
Either of the electric retractable mirrors does not work. 2 51-3
NG
Check the remote control mirror switch (Refer to 51-4). Replace
OK
NG
Check the mirror assembly (retraction operation) (Refer to Replace
51- 4).
OK
(1) NG
Measure at the Mirror control unit connector D-147. Check the following connectors: D-147, D-209 (RHD),
D Disconnect the connector and test on the harness side. D-223, D-27, D- 31 (LHD)
D Ignition switch (ACC)
(1) Voltage between terminal 5 and the body earth. OK NG
OK : Battery voltage
(2) Continuity between terminal 6 and the body earth. (2) NG Check the trouble
symptoms. Repair
OK : Continuity confirmed.
NG
OK
Check the harness between the Mirror control unit and the
battery, and repair if necessary.
Check the harness between the Mirror control unit and the
battery, and repair if necessary.
NG
NG
Check the harness wire, and repair if necessary.
D Between the Remote controlled mirror switch and earth
Inspection Procedure 2
Either of the electric retractable mirrors does not work. Probable cause
The Mirror control unit controls the electric retractable mirror based on input D Mirror assembly fault
signals from the following switches. D Mirror control unit fault
D Ignition switch (ACC) D Harness or connector fault
D Remote control mirror switch (for retracting and returning the mirror)
If the electric retractable mirror does not operate normally, one of the above
input circuit systems, the mirror assembly, or the Mirror control unit may be
defective.
NG
Check the mirror assembly (retraction operation) (Refer to Replace
51- 4).
OK
Measure at the mirror control unit connector D-147 and remote NG Check the following connectors: D-147, D-15, D-25
controlled mirror connector H-07(LH) or H- 13(RH).
D Continuity between the following terminals: OK NG
Between terminals 1 (Mirror control unit side) and 2
(Remote controlled mirror side) Check the trouble Repair
Between terminals 2 (Mirror control unit side) and 1 symptoms.
(Remote controlled mirror side)
OK : Continuity NG
Down
Left
Right
2
1
Removal steps
1. Glove box assembly 3. Mirror control unit
2. Corner lower panel (Passenger’s side)