Professional Documents
Culture Documents
Review Test 7&8
Review Test 7&8
Review Test 7&8
a. 5A b. B c. 5S d. 5Q
5. Which of the following indicates the quantity and unit of are materials still available in the
stockroom?
a. Balance on hand b. Name of project
c. Quantity and unit d. Requisition quantity and unit
7. Which of the following is not just a simple business activity but a strategic process of
innovation and new product creation?
a.Business b. Economics c. Partnership d. Entrepreneurship
11. It is flexible tape measure available in lengths up to 50 feet, other tapes that are 12 to 25
feet are usually considered adequate. Most tapes have an automatic power return.
a. Inside caliper b. Outside caliper c. Try square d. Pull Push Rule
12. Which of the following is a heavy metal made of casting on molds to make fixtures, such as
sinks, tubs, lavatories, covered with a porcelain enamel coating?
a. CI pipe b. GI pipe c. Soil pipe d. Waste pipe
13. These are fittings that joint two different types of pipes together, such as ABS to cast iron
or threaded to a non threaded.
a. Adaptor b. Nipple c. Fixture d. Connector
15. Which of the following were used on technical drawings to represent the location of certain
fixtures, such as plumbing faucets, valves and pipes?
a. Plumbing system c. Schematic diagram
b. Blueprint d. Plumbing symbols
16. What do you call the short length of pipe installed between couplings or other fittings?
a. Nipple b. Faucet c. Fixture d. Connector
17. This is an opening of a pipe fitting, when not in use. It has a male thread on the outside and
a square head.
a. Cap b. Tee c. Plug d. Bell
18. Which of the following tool used for cutting pipes and tubes?
a. Pipe Cutter b. Cold Chisel c. Pipe Reamer d. Pipe Wrench
19. What kind of tool is used for holding firmly any material that need to be cut?
a. Boring tool b. Holding c. Cutting tool d.Measuring tool
20. What kind of valve was found in the water closet flush tank? Does that control the flow of
water into the tank?
a. Check valve b. Gate valve c. Float valve d. Flush valve
22.What do you call the adhesive material specifically used for attachment of threaded pipes or
fittings?
a. Glue b. Contact cement c. Solvent d. Teflon tape
23. What do you call the point of installation system where the flow of water organs could be
manipulated?
a. Adaptor b. Faucet c. Nipple d. Fittings
24. Which of the following were made in different forms intended for plumbing joints and
connections?
a. Fittings b. Faucet c. Nipple d. Lavatories
25. What adhesive material is used by a plumber when working with ABS pipes?
a. Solvent b. Teflon tape c. Duct tape d. ABS cleaner
26. Which of the following refers to polyethylene plastic material intended for long –span
water system installation?
a. PE pipe b. GI pipe c. CI pipe d. PVC pipe
27. Which of the following tools are used to measure internal size of an object?
a. Try square c. Inside caliper
b. Steel square d. Outside caliper
28. Which of the following tools are used to measure external size of an object?
a. Outside caliper b. try square c. Steel square d. inside caliper
29. An implemented used to check and mark right angles in construction work.
a. Try square b. Level bar c. Pull push rule
30. Measure an internal size of an object.
a. Inside caliper b. Outside caliper c. Try square d. steel square
31. Which of the following is a heavy metal made of casting on molds to make fixtures, such as
sinks, tubs, lavatories, covered with a porcelain enamel coating?
a. CI pipe b. GI pipe c. Soil pipe d. Waste pipe
32. A type of fittings used when pipes must change direction, available at 45- and 50- degree
angles.
a. Tee b. Elbow c. Nipple d. Bushing
33. What kind of wood and metal working tool are used for marking/measuring a piece of wood
to get the accuracy of right angle (90 degrees)?
a. Try square b. Steel square c. Steel tape d. Pull push rule
34. What kind of saw was used to cut all kinds of pipes and metals?
a. Rip saw b. Back saw c. Hack saw d. cut saw
35. It is an adjustable wrench used for turning soft iron pipe fittings with a rounded surface.
a. Allen wrench c. Automotive wrench
b. Pipe wrench d. Open wrench
36. What kind of solvent dissolve insoluble in water?
a. Solvent b. Lubricant c. Polar solvent d. Non-polar solvent
37. These are fittings that joint two different types of pipes together, such as ABS to cast iron
or threaded to a non threaded.
a. Adaptor b. Nipple c. Fixture d. Connector
38. What kind of exchangeable device can be connected to an existing plumbing system to
a. Water closet b. Outlets and Drains c. Traps and vents d. fixtures
39. Which of the following pipes are curved then back up, and trap a small amount of water to
create a water seal between the ambient air space and the inside of the drain system?
a. Drain b. Traps c. Cover d. Fixture
40. Which of the following is the toilet top of the traps water seal?
a. Small amount of water c. The water system and drainage pipe
b. The water supply to some fixtures d. The visible water surface in a toilet or in
a closet
42. Which of the following were used on technical drawings to represent the location of certain
fixtures, such as plumbing faucets, valves and pipes?
a. Plumbing system c. Schematic diagram
b. Blueprint d. Plumbing symbols
43. Which of the following is the system that conveys fluids for a wide range of applications?
a. Plumbing b. Printing c. Boring d. Fitting
44. It is flexible tape measure available in lengths up to 50 feet, other tapes that are 12 to 25
feet are usually considered adequate. Most tapes have an automatic power return.
a. Inside caliper b. Outside caliper c. Try square d. Pull Push Rule
45. Which of the following tools are used to measure external size of an object?
a. Outside caliper b. try square c. Steel square d. inside caliper
46. What substance was introduced to lessen friction between moving surfaces, it may also
transport external particles?
a. oil b. power c.lubricant d. solvent
47. Which of the following is a shallow fixture with a flat bottom used in the kitchen?
a. Tub b. Tray c. Sink d. Lavatory
48. What kind of fixture is designed for the washing of hands and faces?
a. Tub b. Sink c. Closet d. Lavatory
49. What kind of valve automatically closes to prevent the flow of fluid in a reverse direction?
a. Check valve b. Gate valve c. Flush valve d. Glove valve
50. According to Plumbing Code of the Philippines, avoid putting vents near the?
a. Living room c. Table and chair
b. Dining room d. Door and window
51. Which of the following type of fittings used to connect different types of pipes in the water
supply system?
a. Union b. Bushing c. Elbow d. Adaptor
56. A points of installation system where flow of water or gas could be manipulated.
a. Teflon tape b. Solvent c. Faucet d. Valve
58. What do you call the working sheet that serves as a complete guide of the student to
certain task to be done?
a. Job order b. Performance task c. Assigned task d. Job description
59. Who is responsible for the overall operation of the worker in the workplace?
a. Foreman b. Lead man c. Job order d. Tool keeper
60. Which of the following indicates the tasks and the material to be used?
a. Bill of materials c. Monetary budget
b. Name of project d. Material description