Professional Documents
Culture Documents
FS-BN-16-MHQI-240 Rev.A
FS-BN-16-MHQI-240 Rev.A
CUSTOMER
CUSTOMER APPROVAL
DATE
PREPARED BY
CHECKED BY
APPROVED BY
1 / 16
FS-BN-16-MHQI-240 REV: A
Revision History
A Original 2020.02.14
2 / 16
FS-BN-16-MHQI-240 REV: A
Contents
3 / 16
FS-BN-16-MHQI-240 REV: A
1. General Specifications
4 / 16
FS-BN-16-MHQI-240 REV: A
2. Pin Assignment
Pin No. Symbol I/O Function Remark
1 GND P Power ground
2 NC - No connect
3 NC - No connect Note 1
4 NC - No connect
5 NC - No connect
6 LCD_ID I LCD_ID
7 VCC P Power supply for analog
8 IOVCC P Power supply logic
Tearing effect output pin to synchronize MPU to
frame writing, activated by S/W command. When
9 FMARK O
this pin is not activated, this pin is low.
If not used, open this pin.
10 CS I Chip select input pin(“Low” enable)
11 RS I Data or command select
12 WR I Write data signal
13 RD I Read data signal
14 DB0 I/O Data bus
15 DB1 I/O Data bus
16 DB2 I/O Data bus
17 DB3 I/O Data bus
18 DB4 I/O Data bus
19 DB5 I/O Data bus
20 DB6 I/O Data bus
21 DB7 I/O Data bus
22 DB8 I/O Data bus
23 DB9 I/O Data bus
24 DB10 I/O Data bus
25 DB11 I/O Data bus
26 DB12 I/O Data bus
27 DB13 I/O Data bus
28 DB14 I/O Data bus
29 DB15 I/O Data bus
30 RESET I Reset pin
31 IMO I Interface select Note 1
32 NC - No connect
33 GND P Power gound
34 LED-1 P Cathode of LED backlight
35 LED-2 P Cathode of LED backlight
5 / 16
FS-BN-16-MHQI-240 REV: A
36 LED-3 P Cathode of LED backlight
37 LED-4 P Cathode of LED backlight
38 LED-A P Anode of LED backlight
39 GND P Power gound
40 NC - No connect
I: input, O: output, P: Power
Note 1: Select the MCU interface mode
IM0 MCU-Interface Mode DB Pin in use
0 80 MCU 8-bit bus interface I DB[7:0]
1 80 MCU 16-bit bus interface I DB[15:0]
6 / 16
FS-BN-16-MHQI-240 REV: A
3. Operation Specifications
3.1. Absolute Maximum Ratings
(Note 1)
Values
Item Symbol Unit Remark
Min. Max.
Voltage for analog VCC -0.3 4.6 V
Voltage for logic IOVCC -0.3 4.6 V
Operation Temperature TOP -20 70 ℃
Storage Temperature TST -30 80 ℃
LED Forward Current IF 30 mA Each LED
Note 1: The absolute maximum rating values of this product are not allowed to be
exceeded at any times. A module should be used with any of the absolute
maximum ratings exceeded, the characteristics of the module may not be
recovered, or in an extreme condition, the module may be permanently
destroyed.
7 / 16
FS-BN-16-MHQI-240 REV: A
3.2. Typical operation conditions
Values
Item Symbol Unit Remark
Min. Typ. Max.
Voltage for analog VCC 2.5 2.8 3.3 V
Voltage for logic IOVCC 1.65 1.8/2.8 3.3 V
Input logic high voltage VIH 0.8xIOVCC - IOVCC V
Input logic low voltage VIL 0 - 0.3xIOVCC V
Input leakage Current ILKG -1 - 1 uA
8 / 16
FS-BN-16-MHQI-240 REV: A
3.4. Timing Characteristics
9 / 16
FS-BN-16-MHQI-240 REV: A
4. Optical Specifications
Values
Item Symbol Condition Unit Remark
Min. Typ. Max.
θL Φ=180°(9 o’clock) - 80 -
θR Φ=0°(3 o’clock) - 80 -
Viewing angle
degree Note 1
(CR ≥ 10)
θT Φ=90°(12 o’clock) - 80 -
θB Φ=270°(6 o’clock) - 80 -
TON - 15 20 msec
Response time Note 3
TOFF - 15 30 msec
Test Conditions:
1. VCI =2.8V, IL=80mA (Backlight current), the ambient temperature is 25℃.
2. The test systems refer to Note 2.
Note 1: Definition of viewing angle range
10 / 16
FS-BN-16-MHQI-240 REV: A
Note 2: Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes operation, the
optical properties are measured at the center point of the LCD screen.
(Response time is measured by Photo detector TOPCON BM-7, other items are
measured by BM-5A/Field of view: 1° /Height: 500mm.)
12 / 16
FS-BN-16-MHQI-240 REV: A
5. Reliability Test Items
(Note3)
Item Test Conditions Remark
High Temperature
Ta = 80℃ 240 hrs Note 1,Note 4
Storage
Low Temperature
Ta = -30℃ 240 hrs Note 1,Note 4
Storage
High Temperature
Ta = 70℃ 240 hrs Note 2,Note 4
Operation
Low Temperature
Ta = -20℃ 240 hrs Note 1,Note 4
Operation
Operate at High
Temperature and +40℃, 90% RH 240 hrs Note 4
Humidity
The sample should be allowed to stand the
Start with cold
following 10 cycles :
temperature, end
Thermal Shock -30℃ for 30 minutes → normal temperature
with high
for 5minutes → +80℃ for 30 minutes →
temperature
normal temperature for 5 minutes, as one cycle.
Frequency range : 10Hz ~ 55Hz
Package Vibration Amplitude of vibration : 1.5mm
Test Sweep time: 12 min
X,Y,Z 2 hours for each direction.
Package Drop Test According to ASTM-D-5327.
13 / 16
FS-BN-16-MHQI-240 REV: A
6. General Precautions
6.1. Safety
Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or
clothes, wash it off immediately by using soap and water.
6.2. Handling
The LCD panel is plate glass. Do not subject the panel to mechanical shock or to excessive force
on its surface.
The polarizer attached to the display is easily damaged. Please handle it carefully to avoid scratch
or other damages.
To avoid contamination on the display surface, do not touch the module surface with bare hands.
Keep a space so that the LCD panels do not touch other components.
Put cover board such as acrylic board on the surface of LCD panel to protect panel from
damages.
Transparent electrodes may be disconnected if you use the LCD panel under environmental
conditions where the condensation of dew occurs.
Do not leave module in direct sunlight to avoid malfunction of the ICs.
6.4. Storage
Store the module in a dark room where must keep at 25±10℃ and 65%RH or less.
Do not store the module in surroundings containing organic solvent or corrosive gas.
Store the module in an anti-electrostatic container or bag.
6.5. Cleaning
Do not wipe the polarizer with dry cloth. It might cause scratch.
Only use a soft sloth with IPA to wipe the polarizer, other chemicals might permanent damage to
the polarizer.
14 / 16
FS-BN-16-MHQI-240 REV: A
7. Block Diagram
15 / 16
FS-BN-16-MHQI-240 REV: A
8. Mechanical Drawing
DOTS DETAIL
SCALE:10/1
irst
Firs
tF
- +
、
、
、
、
16 / 16