Professional Documents
Culture Documents
QR Oma34b
QR Oma34b
BOB is a company that produces high quality products, which 1) Remove the bike's rear QR. Remove the adjust nut and one
encourage a healthy, outdoor, car-free lifestyle. In addition to trailers, conical spring from the BOB QR and install into the rear wheel axle
we also make full suspension jogging strollers. See www.bobgear.com hole on the non-derailleur side.
for our complete line of products.
2) With the QR cam lever in the closed position (note that "CLOSE"
is visible on the cam lever) push the quick release through the bike's
WA R N I N G S rear axle until it contacts the bike frame dropout face.
BOB trailers can be attached to bicycles with wheel sizes between 3) Check for a
20" and 28". Please see the Trailer/Bike Compatibility chart at the minimum of 3/8 inch
end of your trailer manual to determine which trailer is compatible (10mm) and
with your bike. If you have questions about your wheel diameters or maximum 3/4 inch
trailer compatibility with your bicycle, consult your bicycle dealer or (19mm) of threaded
call us at BOB. rod extending past
Our trailers are intended to carry cargo only. the drop out face,
Do not carry children or live animals. Fig. 2.
Cargo capacity: 70 pounds (32 kilograms)
BOB QR must be correctly sized to your specific bicycle to insure IMPORTANT: If the
safe operation. amount of rod FIG.2
SPEED LIMIT: 25 mph (40 kph) A bike with trailer attached, steers extending past the
and feels different. Ride cautiously. Speed wobbles (and loss of dropout face is less Measuring threaded QR rod extending past drop
control) can occur if speed limit is exceeded. than 10mm, you will out face (QR must be in the closed position)
Some variables that can affect the control of your bike and trailer: need a longer quick
improper installation of BOB QR / improper installation of trailer fork release. Please consult the BOB Quick Release Model table to find
retaining pins / improper installation of trailer fork to YAK & IBEX the correct QR for your bike. If the amount of rod is greater than
frame / road conditions / wind speed and direction / cyclist's skill 19mm, see the next section: TRIMMING THE BOB QR". If you do
level / weight of rider relative to the amount of weight in trailer / not understand this section, contact your local bike dealer or call
center of gravity of cargo / integrity of all wheels (proper spoke BOB for help.
tension and bearing adjustment)
4) Install the 2nd conical spring onto the QR
BO B Q R M O D E L S rod (small hole first) and then the adjust nut.
4) Using a file, shape 5) Attach the trailer by aligning the slots of the BOBBINS with the
the end of the rod into slots in the fork hooks. Fig. 8 shows the fork hooks correctly installed
a conical shape. on the BOBBINS.
5) Remove the nut (or 6) With the trailer hooks
die) and verify the QR placed on the bobbins,
rod has been cut to insert the pin in the hole Button Head Post
the proper length by in the front edge of the Pin
repeating steps 2 and hook. Slide the pin under
3 in the previous the bobbin and into the
section then complete hole in the back edge of
QR installation by the hook. Rotate the pin
following steps 4 FIG.5 up, toward the button head
through 7 in previous post on the hook. To
section. QR with die in place and clamped for cutting secure the pin, it is
necessary to press it
Now that the BOB QR is installed, attach the trailer to the bike. To downward and toward the
do this correctly, follow the steps below: hook. When properly
installed, the pin fits Bobbin Hook
between the hook and the Lanyard
head on the button head FIG.9
C a u t i o n post, as shown in Fig. 9.
The rubber lanyard retains Pin Correctly Installed
Attach and detach the trailer ONLY when it is in a straight line with the pin when not installed.
the bike. You can bend the fork otherwise. It is easiest to attach and
detach trailer when it is unloaded. IMPORTANT: The pins are CRITICAL to keeping the trailer attached
to the BOB Quick Release. Inspect pins for proper installation every
trailer attachment time you ride. Incorrectly installed pins can allow the trailer to detach
from the bicycle and cause a severe accident. Please see your dealer
or call BOB if you do not understand the pin installation procedure.
1) The stainless steel
pivoting BOBBINS on the
quick release skewer are
asymmetrical as shown
in Fig. 1. This
asymmetrical design Limited warranty
allows the BOBBINS to
be reversed, allowing for BOB Trailers Inc. takes pride in its workmanship and strives to
a variance of manufacture the best products possible. Therefore, we warranty our
approximately 13mm in BOB QR against defects in material and workmanship subject to the
outside dimensional FIG.6 conditions listed below. Since no product is indestructible, it does
span of the bike's not cover defects attributable to or resulting from normal wear, abuse
dropouts. Correct position for trailer attachment or alteration.
Components are warranted for one year.
2) With the bike stabilized and Warranty is only valid for the original purchaser.
the trailer unloaded, check the Proof of purchase is required to exercise this warranty.
fit between the fork hooks and Labor and transportation are not included.
the slots of the BOBBINS. It is Normal wear, neglect, abuse, accidents, improper assembly or
easiest to do this with the bike maintenance, or the installation of parts or accessories not compatible
in the upright-position and trailer with the original intended use of the trailer, as sold, are not covered
straight behind the bike. Stand by this warranty.
on the left side of the bike facing Warranty claims must be made through an authorized dealer.
towards the trailer. Allow the This warranty is limited to the replacement of the defective part.
bike seat to rest against your BOB Trailers shall in no event be responsible for consequential or
hip. Bend at the hips and lift special damages.
trailer with both hands, Fig. 6, This limited warranty is the only express or implied warranty
and place the fork hooks on the applicable to BOB Trailers. Any implied warranties, including warranties
FIG.7 quick release BOBBINS. If the of merchantability and fitness shall be limited in scope and duration
hooks do not fit into the BOBBIN in accordance with this limited warranty.
Bobbin spacing not aligned with hook
OMA34B