Professional Documents
Culture Documents
Installation Manual Sharp MX-B450P
Installation Manual Sharp MX-B450P
CODE: 00ZMXB450PI1E
LASER PRINTER
MX-B350P / PB / PE / PZ / MX-B351PZ
AR-B352PT / AR-B353PT
MX-B450P / PB / PE / PZ / MX-B451PZ
MODEL AR-B452PT / AR-B453PT
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
Disengage the
pawl.
Transit, Installation (using) environment,Service
MX-B450P
Note Manual
* About a main unit illustration, it may differ from a target model.
If any option is installed, provide the additional space for installing If not, color shift or image distortion may occur.
To assure proper Image quality, make sure the machine is setting
it.
level.
Adequate space must be provide behind the machine for proper
ventilation heat and dust. If not, the machine cannot exhibit func- E. Direct rays of the sun, dust, temperature,
tions against heat and dust, causing some troubles. humidity, gasses, chemicals, vibration
(1) Temperature and humidity (Environmental
11-13/16" conditions)
(30cm)
This machine is designed to perform properly under the specified
temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
11-13/16" Especially when the humidity is too high, paper absorbs humidity to
17-23/32"
cause a paper jam or dirty copy.
(30cm) (45cm)
Do not install the machine near a heater, a cooler, or a humidifier.
Condensation may form inside the machine causing multiple trou-
C. Power source (Capacity, voltage, frequency, bles. Use enough care for ventilation.
safety, plug) Operational environment
If the power specifications are not satisfied, the machine cannot Temperature: 10 to 35C
exhibit full performances and may cause safety trouble. Humidity: 20 to 85% RH
Strictly observe the following specifications. Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(1) Power capacity (2) Contaminates
Check that the following power capacity is satisfied. If not, addition- If dust enters the machine, it may cause dirty copy and a paper
ally provide a power source. jam, resulting in a shortened lifetime.
Current capacity (3) Direct sunlight
Japan: 20A or more If the machine is installed under the rays of the sun, the exterior of
EX 100V: 15A or more the machine may be discolored and abnormal copies may be pro-
EX 200V: 10A or more duced.
NOTE: Check the shape of the power plug of the machine, and (4) Gases and chemicals
insert it into a power outlet of the acceptable shape. Do not install the machine at a place where there are gases and
(2) Power voltage chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Measure the voltage during copying to check that the voltage is in
the range of the specified voltage 10%. Copy quality may be adversely affected and a trouble may be
caused.
If the voltage is outside the specified range, please have a certified
electrician upgrade the outlet. (5) Vibration
(An electrical work is required.) Avoid installation near a machine which produces vibrations.
Use of a step-up transformer is also available. In this case, the If vibrations are applied to the copier machine, copy images may be
capacity must be great enough for the max. power consumption of deflected and a trouble may be caused.
the machine.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
1. System diagram
MX-B350P / PB / PE / PZ / MX-B351PZ
AR-B352PT / AR-B353PT
MX-B450P / PB / PE / PZ / MX-B451PZ
AR-B452PT / AR-B453PT
LASER PRINTER
MX-CS14
600 SHEET PAPER FEED UNIT
MX-DS22
HIGH STAND
Or Or
MX-DS23
LOW STAND
Or Or
NONE NONE
MX-B450P CONFIGURATION 1 – 1
2. Product List
<Main Unit>
US (SIICA/SECL/SCMEX/LAG120V)
Product Name Model cpm Panel HDD Copy Print (PCL/PS) Scan Fax DF Sharp OSA Wireless LAN
MX-B350P Printer W 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B450P model 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
Europe
Product Name Model cpm Panel HDD Copy Print (PCL/PS) Scan Fax DF Sharp OSA Wireless LAN
MX-B350P Printer W 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B350PE model 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B450P 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B450PE 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
Oceania
Product Name Model cpm Panel HDD Copy Print (PCL/PS) Scan Fax DF Sharp OSA Wireless LAN
MX-B350P Printer W 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B450P model 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
Asia
Product Name Model cpm Panel HDD Copy Print (PCL/PS) Scan Fax DF Sharp OSA Wireless LAN
MX-B350PZ Printer W 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B450PZ model 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B350PB 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B450PB 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A STD
MX-B351PZ Printer S 35 5 Line LCD N/A N/A STD N/A N/A N/A N/A N/A
MX-B451PZ model 45 5 Line LCD N/A N/A STD N/A N/A N/A N/A N/A
3. Option List
Item Model name Name 35/45cpm
Paper Feeder MX-CS14 600-SHEET PAPER FEED UNIT OPT
Stand MX-DS22 HIGH STAND OPT
MX-DS23 LOW STAND OPT
PS Expansion Kit --- --- STD
MX-B450P CONFIGURATION 1 – 2
MX-B450P
[2] Service
MX-B350P / PB / PE / PZ / MX-B351PZ Manual
/ AR-B352PT / AR-B353PT /
MX-B450P / PB / PE / PZ / MX-B451PZ / AR-B452PT / AR-B453PT
(MAIN UNIT)
1. Unpacking B. Fixing tape and protection material removal
A. Unpacking
1 2
D. Lock release
(1) Tray rotation plate lock release
1) Gently pull out the tray.
TC protection sheet
ĭ 1) Remove the new toner cartridge from the box. Grasp the car-
ĭ tridge on both sides and shake it horizontally four or five times.
4 or 5 times
B. Tray setup
(1) Default Tray Setting
1) Press the [SPECIAL FUNCTION] key.
The special function screen will appear.
2) Select "System Settings" with the [▼] or [▲] key and press the
[OK] key.
3) Enter the administrator PIN code with the numeric keys.
• " * " appears for each digit that you enter.
• The mode selection screen appears.
4) Select the [COPY] with the [▼] or[▲] key.
5) Press the [OK] key.
6) Select the [Default Tray Setting] with the [▼] or[▲] key.
7) Press the [OK] key and follow the instructions in the setting
screen.
8) Select the desired tray with the [▼] or[▲] key.
9) Press the [OK] key.
A4
A6
Holder
SIM No Content
26 6 Used to set the destination.
SIM No Content
26 18 Used to set YES/NO of the toner save mode (Only in
UK and Japan versions)
* For other destination versions, this setup is made by
the user program.
No Item SIM
1 Printer gray balance/density check 64-5
No Item SIM
1 Print image position adjustment 50-10
Set each set value to the default and press [START] key. The print
test pattern is printed.
The print density must be changed gradually from the lighter level
to the darker level. The density changing direction must not be
reversed.
2 1
3) Remove the sponge.
3
C. Packed items check
4) Release the screw and take off the Cabinet –Rear from Cas-
sette.
Locating boss
Figure A
1. Unpacking
Unpack the package, and check to confirm that all the parts are provided.
<MX-DS22>
<MX-DS23>
Packed parts
8
4 7
2 3
6
1 LOW STAND 3 10 1 HIGH STAND
11 12 13
Connection between Main unit and High Connection between 600-Sheet Paper
stand / Low stand. Feed Unit and High stand / Low stand.
No. Name Type A Type B Type C Type D
1 High Stand 1 Not use 1 Not use
Low Stand Not use 1 Not use 1
2 Tip-resistant L Plate 2 2 2 2
3 Fix Plate A R1 1 1 2 2
4 Fix Plate A R2 Not use Not use 2 2
5 Fix Plate A FL Not use Not use 1 1
6 Fix Plate A FR Not use Not use 1 1
7 Fix Plate B R1 2 2 Not use Not use
8 Fix Plate B R2 2 2 Not use Not use
9 Fix Plate B FL 1 Not use Not use Not use
10 Fix Plate B FR 1 1 Not use Not use
11 S-Tite Screw 4-8 4 6 3 6
12 Machine Screw 4-6 (Black) 3 Not use 3 Not use
13 Machine Screw 4-14 4 4 4 4
AƩachment the plate spring. 2) After place Main body and remove paper feed tray.
Positioning pin
Raise Tip-resistant L Plate.
Item No.13
(Machine Screw 4-14)
Ĭ
ĭ
Į 5) After remove cassette, attach Fix Plate FR (Item No.6) and Fix
Plate A FL (Item No.5).
3) Gently place the upper Opt.Cassette onto the low stand, align-
ing and inserting the 3 locating bosses of the low stand into the
locating holes on the bottom of the upper unit.
Example:
Trademark acknowledgements
x Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0,
Windows® 2000, Windows® XP, Windows® Vista, Windows® 7, Windows® 8,
Windows® 8.1, Windows® Server 2003, Windows® Server 2008,
Windows® Server 2012 and Internet Explorer®
are registered trademarks or trademarks of Microsoft Corporation in the U.S.A.
and other countries.
x PostScript is a registered trademark of Adobe Systems Incorporated.
x Macintosh, Mac OS, AppleTalk, EtherTalk, Laser Writer, and Safari are registered
trademarks or trademarks of Apple Inc.
x IBM, PC/AT, and Power PC are trademarks of International Business Machines
Corporation.
x Acrobat® Reader Copyright® Adobe Systems Incorporated. All rights reserved.
Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe
Systems Incorporated.
x PCL is a registered trademark of the Hewlett-Packard Company.
x Sharpdesk is a trademark of Sharp Corporation.
x All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Business Solutions BU