Professional Documents
Culture Documents
ISO 00378-1980 Scan
ISO 00378-1980 Scan
ISO 00378-1980 Scan
I N TE R N ATI O N AL OR G AN I ZATI O N FOR S TAN D AR D I Z ATl O N . M E X, I I YH AP O ~ H AR O P rAH M 3 ALWl R tl 0 C TAH ~ AP TM 3 ALWl M @ OR G AN l S ATl ON I N TE R N ATI ON ALE DE N O R M ALI S ATI O N
D escri pto rs : spo rt e q u i pm e n t, g ym n asti c e q u i pm e n t, spe ci fi cati o n s, safe ty, d i m e n s i o n s, m e ch an i cal tests, be n d te sts, stabi l i ty te sts.
P ri ce bas ed on 3 pag e s
Foreword
I S0 (th e I n tern ati on al Org an i zati o n for Stan d ard i zati o n ) is a wo rl d wi d e fed erati on of
Draft I n tern ati on al Stan d ard s ad opted by th e tech n i cal co m m i tte e s are ci rcu l ate d to
th e I S0 C o u n ci l .
I n tern ati on al Stan d ard I S0 378 was d evel oped by Tech n i cal C o m m i tte e I SO/TC 83,
Fran ce Po l an d U S SR
te ch n i cal g rou n d s
I tal y
Th i s I n tern ati on al Stan d ard can ce l s an d repl ace s I S0 Re com m en d ati on R 3 78-1 964, of
P ri n te d in S wi tz e rl an d
I N TE RN ATI ON ALS TAN D ARD I S0 3 78- 1 980 (E )
1 Scope an d fi el d of appl i cati on fu n cti o n al ch aracte ri s ti cs as wood ( i m pact stren g th , sweat ab-
req u i re m e n ts for paral l e l bars for u se in com peti ti o n s an d trai n - Th e fram e, co l u m n s an d su pports s h al l be of stee l or cast i ro n
of th e m an u factu rer.
Th e bars sh al l be of wood , l am i n ated ( or at l east h ave a su rface traverse , for e xam pl e by m ean s of bottom board s or a m e tal
of wood ) wi th re i n fo rci n g core (i n ord er to preven t total pl ate, or a m at s h al l be i n se rted . Th e bottom board s or th e m at
D i m e n si o n s in m i l l i m e tre s
420 to 520
3 500 t 1 0
-
- --I
I 1 I
I
I
t 1
Bar S u ppo rt A,
(sl i d e )
‘L N o n - sl i p
a) Si d e vi e w b) Fron t vi e w
B o tto m bo ard , m at
or m e tal pl ate
M od el for passag e
f-
Lo n g i tu d i n al m e m be r
. ; 250 to 3 50 -- t- -- -
ti
Ll J ppe r ed g es ro u n d e d
-I I I o ff wi th rad i u s 1 0 mm min.
R 50
d) M od el for passag e
c) S e cti o n A- A
J oi n t
pi n
* Th e to l eran ce s of
th i s d i m en si on
e) Bar su ppo rt
i n fl u e n ce th e rad i i .
f) P ro fi l e of bars
Fi g u re 1 - D i m e n si o n s of paral l e l bars
I S0 3 7849 80 (E l
5 D esi g n 5. 4 Ad j u s tm en t of bars
m en t s h al l no l on g er be po ssi bl e. Th e l o cki n g d e vi ce s h al l be
d i m i n i sh e d d u ri n g u se,
5. 5 S tabi l i ty
5. 3 D e fl e cti o n of bars
Wh en l oad ed wi th a test force F = 1 350 N in th e ‘ cen tre of fl oo r, sh al l re si st a h o ri zon tal test fo rce F = 900 N wi th ou t
each of th e bars, th e bars bei n g ad j u sted to a h ei g h t of l i fti n g . Th e test force sh al l be appl i ed by m e an s of two cabl e s
1 750 mm, th e bars sh al l h ave a d efl e cti on f = 60 + 6 mm. each 2 300 + 1 5 mm l on g , attach ed to th e poi n ts of su pport of
po si ti o n .
Tu rn bu ckl e m e te r