Professional Documents
Culture Documents
Az5b0s 01F
Az5b0s 01F
Features
ESD protection for one line with bi-direction AZ5B0S-01F is a unique design which includes
Provide transient protection for the protected proprietary clamping cell with ultra-low
line to capacitance in a small package. During transient
IEC 61000-4-2 (ESD) ±15kV (air) / ±12kV (contact) conditions, the proprietary clamping cell prevents
IEC 61000-4-5 (Lightning) 7A (8/20µs)
over-voltage on the control lines, or data lines,
Ultra-low capacitance: 0.18pF typical
protecting any downstream components.
For low operating voltage applications: 2.0V
and below AZ5B0S-01F is bi-directional and may be used
0201 small DFN package saves board space on lines where the signal swings above and
Fast turn-on and low clamping voltage below ground.
Solid-state silicon-avalanche and active circuit
AZ5B0S-01F may be used to meet the ESD
triggering technology
immunity requirements of IEC 61000-4-2, Level 4
Green part
(±15kV air, ±8kV contact discharge).
Applications
2.5G/5G/10GbE
Thunderbolt interface Circuit Diagram /
USB3.1 and USB3.0 interfaces Pin Configuration
USB Type-C interface
DisplayPort interface
Hand held portable applications
Description 1
AZ5B0S-01F is a design which includes a
bi-directional ESD rated clamping cell to protect
high-speed data interfaces in an electronic
system. The AZ5B0S-01F has been specifically
designed to protect sensitive components which
2
are connected to data and transmission lines
from over-voltage caused by Electrostatic
Discharging (ESD), Lightning, and Cable DFN0603P2Y (Bottom View)
Discharge Event (CDE). (0.6mm x 0.3mm x 0.3mm)
Specifications
Absolute Maximum Ratings (TA= 25oC, unless otherwise specified)
Parameter Symbol Rating Unit
Peak Pulse Current (tp=8/20µs) Ipp 7 A
Operating Voltage VDC ±2.2 V
ESD per IEC 61000-4-2 (Air) VESD-1 ±15
kV
ESD per IEC 61000-4-2 (Contact) VESD-2 ±12
o
Lead Soldering Temperature TSOL 260 (10 sec.) C
o
Operating Temperature TOP -55 to +125 C
o
Storage Temperature TSTO -55 to +150 C
Electrical Characteristics
Parameter Symbol Condition Min Typ Max Unit
Reverse Stand-Off
VRWM T=25 oC. -2 2 V
Voltage
Reverse Leakage
ILeak VRWM = ±2V, T=25 oC. 500 nA
Current
Reverse
VBV IBV = 1mA, T=25 oC. 5.5 10 V
Breakdown Voltage
Surge Clamping
VCL-surge IPP = 7A, tp = 8/20µs, T=25oC. 4 5.5 V
Voltage
Channel Input
CIN VR = 2V, f = 1MHz, T=25 oC. 0.18 pF
Capacitance
Note 1: ESD Clamping Voltage was measured by Transmission Line Pulsing (TLP) System.
TLP conditions: Z0= 50Ω, tp= 100ns, tr= 1ns.
Typical Characteristics
Reverse Clamping Voltage vs. Peak Pulse Current Transmission Line Pulsing (TLP) Measurement
7 25
5 10
_
5
4
0
3
-5
2 -10
Peak Pulse Current (A) Transmission Line Pulsing (TLP) Voltage (V)
0.20
0.15
0.10
0.05
0.00
-3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0
Application Information
The AZ5B0S-01F is designed to protect one In order to obtain enough suppression of ESD
line against system ESD pulse by clamping it to induced transient, a good circuit board is critical.
an acceptable reference. It provides bi-directional Thus, the following guidelines are recommended:
protection. Minimize the path length between the
protected lines and the AZ5B0S-01F.
The usage of the AZ5B0S-01F is shown in Fig. Place the AZ5B0S-01F near the input
1. Protected line, such as data line, control line, terminals or connectors to restrict transient
or power line, is connected at pin 1. The pin 2 is coupling.
connected to a ground plane on the board. In The ESD current return path to ground
order to minimize parasitic inductance in the should be kept as short as possible.
board traces, all path lengths connected to the Use ground planes whenever possible.
pins of AZ5B0S-01F should be kept as short as NEVER route critical signals near board
possible. edges and near the lines which the ESD
transient easily injects to.
Input Output
VBR VCL
Transient gnd gnd
Voltage
-VBR -VCL
VBR
Normal gnd gnd
Operation
-VBR
Protected
Devices
1 1
AZ5B0S-01F
AZ5B0S-01F
2 2
Fig. 1
D
0.65
L1 L2
O
45
Marking Code
0.05
0.05
C1 C2
e
BOTTOM VIEW
T = Device Code
Millimeters
Symbol
Min. Nom. Max.
Part Number Marking Code
E 0.55 0.60 0.65
D 0.25 0.30 0.35 AZ5B0S-01F.R7G
A 0.28 0.30 0.32
T
(Green Part)
A1 0.00 0.02 0.05
Note. Green means Pb-free, RoHS, and
L1 0.13 0.18 0.23
Halogen free compliant.
L2 0.14 0.19 0.24
C1/C2 0.20 0.25 0.30
e 0.35 BSC
Ordering Information
PN# Material Type Reel size MOQ MOQ/internal box MOQ/carton
AZ5B0S-01F.R7G Green T/R 7 inch 12,000/reel 4 reels= 48,000/box 6 boxes =288,000/carton
Revision History
Revision Modification Description
Revision 2020/03/02 Formal Release.