This document provides a summary of common error codes and faults for various washing machine brands, including GE, IFB, Bosch, Frigidaire, and more. It lists specific error codes, the component or issue they indicate, such as problems with the door lock, motor, water inlet, drain pump, temperature sensors, control boards, and other parts. The document serves as a reference for technicians troubleshooting washing machine issues.
Original Description:
Original Title
Washing machines and Washers error codes - Fault codes
This document provides a summary of common error codes and faults for various washing machine brands, including GE, IFB, Bosch, Frigidaire, and more. It lists specific error codes, the component or issue they indicate, such as problems with the door lock, motor, water inlet, drain pump, temperature sensors, control boards, and other parts. The document serves as a reference for technicians troubleshooting washing machine issues.
This document provides a summary of common error codes and faults for various washing machine brands, including GE, IFB, Bosch, Frigidaire, and more. It lists specific error codes, the component or issue they indicate, such as problems with the door lock, motor, water inlet, drain pump, temperature sensors, control boards, and other parts. The document serves as a reference for technicians troubleshooting washing machine issues.
Washing machines and Washers error codes - Fault codes
GE front lading washing machine error codes
E22 – Water Fill timeout E23 – Flood protect drain E30 – Drain pump not present E31 – Drain timeout E38 – Dispenser error E39 – Dispenser timeout E42 – Drive motor E43 – DC Fault E45 – Drive motor E46 – Drive motor E47 – Heat sink E48 – Drive motor E49 – Load too heavy E4A – Under volts E4B – Power up problems E4C – Over volts E4E – Under volts after start E4F – EEProm fault E52 – Main control E53 – Buffer error Internal software buffer error E54 – No motor response E57 – Checksum failure E58 – Communication failure E60 – Door lock switch failure E61 – Door unlock switch failure E62 – System contact failure E63 – Unexpected open door E64 – Unexpected open door while running E65 – Water level sensor failure E66 – Water temperature sensor open E67 – Water temperature sensor shorted E70 – Stuck key E71 – Key fault Communication error GE WSL washing machine error codes IE – Water level sensor error 7E – Water supply error E – Drain pump error dE – Lid open error UE – Unbalance switch error OE – Water overflow error IFB Washing Mahcines error code/fault codes 1:IFB Washing Machine Not Turning ON OR Turns ON But Does not Starts. 2:IFB Washing Machine Door Does Not Opening. DE Error 3: Water is not coming inside the IFB Washing Machine Inlet problem 4:Water is Leaking from the washing machine, drum or hose pipe damaged 5:Wash is not happening / Spin not Happening in the IFB Washing Machine 6:Drum NOt rotating or Drum Making Huge Sound while spin cycle, 7:Water not Draining From the washing Machine 8:Burning smell, Tripping Problem, etc IFB Amana washing machine error codes “Sd” – (Excess suds) F8 followed by E1 – (water supply error) F9 followed by E1 – (drain pump system error) F5 followed by E2 – (door will not lock) F7 followed by E1 – (motor drive error) “rL” – (remove load) Washer making error beeps – Door has not been opened and closed for at least 3 cycles Washer beeps when HOLD TO START is touched – Door not closed F# E# code other than as described above appears in display – System Code Error “nt” (interrupted) – Cycle was paused or cancelled Clean Washer LED flashing at end of wash cycle – The washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer cycle. IFB Asko washing machine error codes F1 – Water supply/low water fill F2 – Water level too high F3 – Pump problem F4 – Thermistor problem F5 – Fault in thermal cutout or heating pause fault F6 – Motor fault F7 – Door lock release fault 00 – Machine did not spin Beko washer error codes H1 – NTC Open or Short Circuit H2 – Heater Open Circuit H3 – Heater Always On H4 – Valve Triac Short Circuit H5 – Pump Open Circuit H6 – Motor Triac Short Circuit H7 – Pressure Sensor Failure H11 – Motor & or Tacho Open Circuit Bosch washing machine error codes F16 – Door lock error F17 – Inlet valve error detected F18 – Drain error detected F23 – Anti flood device has been activated F34 – Door lock error F42 – Motor fault F43 – Motor fault F44 – Motor fault Bosh WAE range washing machine error codes F16 – Door lock problem F17 – Inlet valve F18 – Drain pump F21 – Motor F23 – Anti flood system activated Bosch WEP range washing machine error codes F01 – Water intake timeout F02 – Heating timeout F03 – Draining timeout F04 – Motor fault F05 – Uncontrolled motor startup F06 – Short on NTC Detected on hot water intake F07 – Open circuit NTC Open circuit wiring F08 – Door open when program started F09 – Unexpected heating F10 – Communication error F11 – Overheating F12 – Short circuit F13 – Mains voltage too high F14 – Mains voltage too low F15 – Faulty temperature sensor on motor PCB F16 – Faulty rinse sensor Displayed only in test Daewoo washing machine error codes E2 = Water has overfilled and the error code is displayed E5 = High Voltage Error E7 = Directional Error E8 = Washer Motor Error E9 = Pressure Sensor Error H2 = Wash Temperature Sensor H4 = Overheating Washer Heating Element H6 = Washer Heating Element Failed H8 = Heater Overheating / No Water Washer IE = Water Inlet Error – Washing Machine Did Not Fill With Water LE = Washing Machine Door Open OE = Water Has Not Drained From The Washer PEF = Filter Is Detected As Blocked UE = Washer Load Imbalance Fisher & Paykel to-load aqua smartwashing machine error codes 21, 26, 27, 49, 50, or 246 = Water Inlet Valve Fault 38 or 39 = Water Level Pressure Transducer Air Tube Fault 58 or 68 = Water Level Pressure Transducer Fault 10, 41, or 237 = Water Temperature Sensor Fault 1, 57, 60, 107, 108, 112, 133, 220, 221, 222, 223, 224, 225, 226, 230, 232, 233, 236, 241, 243, 252, or 254 = Motor Control Module Fault 45, 46, 103, 104, 105, 106, or 241 = Display Module Fault 234, 235, 238, or 239 = Lid Lock is Bad 40, 56, or 160 = Spin Basket Will Not Engage Or Disengage From Clutch 136 or 137 = Motor Is Not Running 37, 114, 245, 247, 248, 249, 250, or 253 = Water Is Not Draining Frigidaire front loading washing machne error codes E10 – Water doesn’t enter E20 – Water dosen’t drain E30 – Drum overfilled E40 – Door is open E50 – Motor is overheated E70 – Cold water doesn’t enter EF0 – Over sudsing EF0 – Hot water doesn’t enter E11 – Fill time too long E13 – Water leak in tub or air leak E21 – Water not pumping out fast enough E23 – Drain pump relay on control board failed or wire off pump E24 – Drain pump relay on control board failed or wire off pump E31 – Pressure sensor not communicating with control board E35 – Pressure sensor indicates water overfill E36 – Control board problem E41 – Control board thinks the door switch is open E43 – Control board problem E44 – Control board problem E45 – Control board problem E46 – Control board problem E47 – Board thinks door PTC circuit is open in spin E48 – Board thinks door PTC circuit is closed E52 – Bad signal from tacho generator E56 – High motor current E57 – High current on motor phase E59 – No tacho signal for 3 seconds E5A – High temp on heat sink caused by overloading E5B – High temp on heat sink E5C – High temp on heat sink E5D – Communication problem E5E – Communication problem E5F – Communication problem E66 – Heating element relay failure E67 – Input voltage on microprocessor incorrect E68 – Current leakage to ground on heater or fuse opened E70 – The control board is not seeing the correct water supply E71 – Wash NTC failure E74 – Wash temperature does not increase E75 – Water temperature sensor circuit E76 – NTC temperature for the cold water valve over the limits E82 – Console control problem E83 – Console control problem E91 – Communication error between UI board and control board E93 – Console control problem E94 – Console control problem E95 – Communication error E97 – Console control problem E98 – Console control problem EB1 – Incoming power frequency out of limits EB2 – Incoming line voltage above 130 vac EB3 – Incoming line voltage below 90 VAC EF1 – Clogged drain pump EF2 – Too much soap EBE – Console control problem EBF – Console control problem EF5 – NTC temperature for the hot water valve over the limits F1 – Internal fault in control F2 – Water temperature problem F3 – Water level problem F4 – Washer is not advancing F5 – Keypad problem
Haier washing machine error codes
bLoC PunP – Water not draining out / No drain no tAPS – Not filling up with water Err1 – Washing machine door error detected = Not closed Err2 – Water has not drained from the washer Err3 – Detected washer temperature sensor error Err4 – Washer heating element fail Err5 – Water level not reached expected level Err6 – Washing machine motor speed incorrect Err7 – Motor speed error detected Err8 – Washer has overfilled with water ErLC – Door lock has failed ErUL – Door lock failure EUAr – Communication failure between display board and power board Unb – Unbalanced wash load PF – Voltage is less than 93 Volts AC CLrF – Too much detergent suds Hotpoint washing machine error codes F01 – Electronic circuit board fault F02 – Motor circuit fault F03 – Temperature sensing fault F05 – Waste pipe blockage or pump issue F06 – Door lock fault F07 – Electronic circuit board fault / heating circuit fault F08 – Heater fault F09 – Software fault F11 – Pump circuit fault F12 – Electronic control fault F13 – Dryer temperature sensing fault (washer dryers only) F15 – Heater control fault (washing machines and washer dryers) F16 – Drum lock position sensor fault (top loading machines only) F18 – Internal data error F19 – Fan motor or heating fault (washer dryers only) Kenmore Oasis Whirlpool Cabrio and Maytag Bravos washer error codes LF – Long Fill Ld – Long Drain uL – Unbalanced Load oL – Overloaded Sd – Suds Detection id – Open or Close Lid Po – Pump Out HC – Hot and Cold reversed dL – Lid Lock Failure dU – Lid Unlock Failure F1 – Pressure Signal Out-of-Range F2 – Keypad Interface Failure F40 – Thermistor Open F41 – Motor RPS Thermistor Open F42 – Heater in Unknown state F43 – Heater is continuously On F44 – Heater cannot be turned On F50 – Motor Stalled F51 – Motor RPS Failure F52 – Motor Stop Failure F53 – Motor Control Over temp F54 – Motor Control Over current F72 – Basket Re-engagement Failure LG front loader washing machine error codes IE – Water inlet error UE – Unbalance error OE – Drain error FE – Over flow PE – Pressure sensor error dE – Door open error CE – Oven current error LE – Locked motor error bE – Ball sensor error EE – EEprom error PF – Power failure E1 – Leakage error Maytag front loading Neptune washer error codes DO – Door Open FL – Failed to lock LO – Door failed to unlock Lr – Locked Motor Rotor ND – No Drain NF – No Fill OD – Opened Door Sd – Suds lock PF – Power failure Samsung Front load – Top load washer error codes dc – Unbalanced load dL – Door is not locked when washer is running FL – Washer failed to lock the door Hr – Water temperature control problem LE – Washer tried to fill but has not reached correct water level LO – Door will not unlock E3 – Motor not running properly nd – Washer is not draining nF – Washer tried to fill 4E – Washer cannot fill with water Sr – Problem with control PF – Power failure OE – Water level sensor bE – Motor speed sensor tE – Temperature sensor 3E – High current detected 2E – High/low voltage detected 5r – Problem with control 8E – Vibration sensor Whirlpool AQ, AW model washer error codes FH – No Water Inlet FA – Aquastop Failure FP – Drain Failure F5 – NTC Failure F6 – Tachometer Failure F7 – Triac Short Circuit detection F8 – Heating Element, Open Circuit F9 – Overflow Failure F10 – Motor control unit (Thermal) F11 – Communication failure F12 – Heating Element Short Circuit F13 – Dispenser Circuit Error F14 – EEPROM Failure F15 – Motor Control Unit Error F16 – Control Failure (Control Unit) F18 – Control Failure (Control Unit) F20 – Control Failure (Control Unit) F21 – Control Failure (User Board) F22 – Control Failure (User Board) FDL – Door Lock Error FDU – Door Unlock Error