Professional Documents
Culture Documents
Rotrex Technical Datasheet C30 Rev6.0
Rotrex Technical Datasheet C30 Rev6.0
Rotrex Technical Datasheet C30 Rev6.0
Rev. 6.0
Reliable construction
Installation flexibility
Reduced emission
GENERAL DESCRIPTION
The C30 is a range of centrifugal superchargers with a very versatile application range. Countless
number of medium size applications can be boosted by this very efficient and silent unit which supplies
air flow up to 0.39 kg/s.
Impeller speeds of up to 120,000 rpm are achieved through the patented hi-speed planetary traction
drive which combines small size with exceptional performance and durability.
The very low noise and vibration characteristic as well as the high efficiency of these superchargers
set the industry standard for what is achievable.
The C30 range of superchargers is designed for four stroke gasoline engines. However, two stroke
engines or even diesel engines can benefit from these superchargers with remarkable results.
Depending on the application the C30 will support engine outputs up to 320kW. Where one
supercharger is not enough, it is possible to use two units to support large amounts of power in a
twin-charger configuration. The C30 can also supply clean pressurized air for other applications such
as industrial systems, exhaust gas after-treatment systems, agriculture applications, fuel cell power
plants etc.
The groundbreaking compact size enables a very flexible supercharger installation particularly on
engine applications with tight space and where weight and size are essential.
The supercharger features an integrated dual-action oil pump that works as a dry sump scavenging
pump in addition to being the oil supply pump. The self-contained oil system allows flexible positioning
of the supercharger on the vehicle and has the benefit of fitting the supercharger without worrying
about tampering with the oil system of the engine or any other accessory.
The Rotrex C-type supercharger has been developed and extensively tested with the special Rotrex
traction fluid. To maintain the ultimate level of performance and durability it is very important that
the unit is exclusively run with special Rotrex traction fluid. Make sure the inlet oil temperature is
within the range specified in the table on the next page. Any deviation from the standard Rotrex oil
circuit requires approval from Rotrex.
WWW.ROTREX.COM Page 1 of 8
ROTREX C-range C30 supercharger
Rev. 6.0
Rotational direction Rindirection Clockwise rotation, as seen from pulley side CCW[1]
Max mass flow rate Mflow 0.28 kg/s 0.31 kg/s 0.32 kg/s 0.39 kg/s
Mass moment of inertia ISupercharger 5.08·10-3 kg·m2 5.14·10-3 kg·m2 5.14·10-3 kg·m2 5.153·10-3 kg·m2
max
Max drive efficiency 97%
Rotrex Pulley ring diameters 70, 75, 80, 85, 90, 95, 100, 105, 110 mm
Øpulley
available 8 rib aluminium - PK profile
Conversion Toolbox
5 9
Temperature conversion ⁰C = x (⁰F-32) OR ⁰F = x ⁰C + 32
9 5
kg kg CFM
Kg/s to CFM conversion CFM = x 1731.8 = @15⁰C and 0.1013 MPa
s s 1731.8
Kg
Kg/s to lb/min conversion kg lb lb
= 0.0075 = s
s min min 0.0075
WWW.ROTREX.COM Page 2 of 8
ROTREX C-range C30 supercharger
Rev. 6.0
C30-64 Compressor
C30-64 Compressor Map map
3.0
2.8
120k
2.6
2.4
68
2.2
70
Pressure Ratio
100k
2.0
1.8
60
80k 72
1.6
65
50
1.4
60k
50
1.2
50 55
40k
40
45
20k 35
1
0 0.05 0.10 0.15 0.20 0.25 0.30
Air Flow [kg/s] RTR 0068
WWW.ROTREX.COM Page 3 of 8
ROTREX C-range C30 supercharger
Rev. 6.0
C30-74 Compressor
C30-74 Compressor Map map
3.2
3.0
2.8
120k
2.6
50
2.4
65
Pressure Ratio
2.2
100k
2.0
1.8
72
80k
1.6
50
70
68
1.4
60
60k 50
1.2
40k 55
50
40
45
20k 35
1
0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
Air Flow [kg/s] RTR 0069
WWW.ROTREX.COM Page 4 of 8
ROTREX C-range C30 supercharger
Rev. 6.0
C30-84 Compressor
C30-84 Compressor Map map
3.0
2.8
120k
2.6
2.4
65
55
2.2 100k
Pressure Ratio
68
2.0
70
60
1.8
80k 72
1.6
1.4 60k 55
1.2
40k
50
4 45
35 0
20k 35
1
0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
Air Flow [kg/s] RTR 0070
WWW.ROTREX.COM Page 5 of 8
ROTREX C-range C30 supercharger
Rev. 6.0
C30-94/C30-94
C30-94 Compressor CCW
Map Compressor map
2.8
2.6
100k
2.4 55
60
90k
2.2
2.0
Pressure Ratio
80k
55
1.8
70k
70
68
1.6
60k
71
1.4
50k
65
60
40k
1.2 50
30k
45
20k 45 40
1
0 0.06 0.12 0.18 0.24 0.30 0.36 0.42
Air Flow [kg/s] RTR 0071
WWW.ROTREX.COM Page 6 of 8
Rev. 6.0
The supercharger can be ordered with the compressor housing mounted in one of six Max ±15° from
different outlet positions with 60° intervals to allow easy adoption to any application. horizontal in any
direction
WWW.ROTREX.COM
0° 60° 120° 180° 240° 300°
94°
A 60° (6x)
0
-0,021
,5 38,7
96
Ø
29
50
5
41
,5
ROTREX C-range C30 supercharger
O 19,05 h7
60°
(6x
A
)
132
ØB
ØC
Ø 53
Ø 113
R 8,
5
68
R1
0
28 R6
4,5
R1
Pulley Adapter 0
31,9
Supplied M6x10 81,5
Pulley mounting bolt 5,2 The supercharger must be
positioned with the flat 146
C30 range Dimensions
DETAIL A
A B C Oil OUT
C30-64 178 49 60
Oil IN
C30-74 178 51 60
C30-84 182 51 76
C30-94 182 61 76
Pulley ring ø 70 75 80 85 90 75 80 85 90
Pulley rotational direction Rotrex pulley ring mounted
Rotrex Pulley ring ø 70 75 80 85 90 95 100 105 110 All dimensions in mm unless otherwise specified
Page 7 of 8
The supercharger can be ordered with the compressor housing mounted in one of six
different outlet positions with 60° intervals to allow easy adoption to any application. Max ±15° from Rev. 6.0
horizontal in any
Possible outlet directions direction
!
WWW.ROTREX.COM
0° 60° 120° 180° 240° 300°
94°
0
-0,021
96
,5 38,7
50
,5
Ø
41
5
Ø
O 19,05 h7
60°
ROTREX C-range C30 supercharger
(6x
A
)
132
Ø 53
Ø 76
Ø 113
Ø 67,5
R 8,
5
68
R1
0
R6
4,5
R1
Pulley Adapter 0
31,9
Supplied M6x10 81,5
Pulley mounting bolt 5,2 The supercharger must be
positioned with the flat 146
part facing down and within
15° from horizontal in any direction
DETAIL A
C30-94 CCW Dimensions
Oil IN
Oil OUT
Pulley ring ø 70 75 80 85 90 75 80 85 90
Rotrex pulley ring mounted CCW Pulley rotational direction
Rotrex Pulley ring Ø 70 75 80 85 90 95 100 105 110 All dimensions in mm unless otherwise specified
Page 8 of 8