Professional Documents
Culture Documents
Sony HDR-CX330 CX330E PJ330E PJ340 PJ340E PJ350 PJ350E Lev2
Sony HDR-CX330 CX330E PJ330E PJ340 PJ340E PJ350 PJ350E Lev2
Sony HDR-CX330 CX330E PJ330E PJ340 PJ340E PJ350 PJ350E Lev2
983477432.pdf
SERVICE MANUAL
Ver. Date History Contents
issued
LEVEL 2 1.0 2014.01 Official Release — —
1.1 2014.03 Revised-1 • Addition of HDR-PJ350. Yes
Ver. 1.1 2014.03 US Model (A1 13-209) Page 2, 1-1, 2-1, 2-5, 2-7
Canadian Model
Revised-1 AEP Model
Replace the previously issued UK Model
SERVICE MANUAL 9-834-774-31 North European Model
with this Manual.
E Model
Hong Kong Model
Chinese Model
Korea Model
Brazilian Model
Tourist Model
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
–2–
Caution 注意
Danger of explosion if battery is incorrectly replaced. 如果电池更换不当会有爆炸危险。
Replace only with the same or equivalent type. 只能用同样类型或等效类型的电池来更换。
Dispose of used batteries according to the instructions. 务必按照说明处置用完的电池。
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered UNLEADED SOLDER
connections. Check the entire board surface for solder splashes and This unit uses unleaded solder.
bridges. Boards requiring use of unleaded solder are printed with the lead free
2. Check the interboard wiring to ensure that no wires are pinched or mark (LF) indicating the solder contains no lead.
contact high-wattage resistors. (Caution: Some printed circuit boards may not come printed with the
3. Look for unauthorized replacement parts, particularly transistors, lead free mark due to their particular size.)
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of : LEAD FREE MARK
deterioration. Point them out to the customer and recommend their Be careful to the following points to solder or unsolder.
replacement.
5. Check the B+ voltage to see it is at the values specified. • Set the soldering iron tip temperature to 350 °C approximately.
6. Flexible Circuit Board Repairing If cannot control temperature, solder/unsolder at high temperature
• Set the soldering iron tip temperature to 350 °C approximately. for a short time.
• Do not touch the soldering iron on the same conductor of the circuit Caution: The printed pattern (copper foil) may peel away if the
board (within 3 times). heated tip is applied for too long, so be careful!
• Be careful not to apply force on the conductor when soldering or Unleaded solder is more viscous (sticky, less prone to
unsoldering. flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
–3–
Ver. 1.1 2014.03
The changed portions from 1. SERVICE NOTE
Ver. 1.0 are shown in blue.
1-1. POWER SUPPLY DURING REPAIRS About unit with Internal Memory Model (PJ340/PJ340E/PJ350/PJ350E)
After the board replacement, execute the procedure below first.
1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 Vdc), the power is shut off
2. Execute the script files below. (Refer to the flowchart in Fig. 1)
so that the unit cannot operate.
• 14DdmMmcReadTestMINI_v6.vbe
These following method is available to prevent this.
• 14DdmMmcMakePartition_v6.vbe
Method: Unless these script files are executed, the following symptoms may appear.
Use the AC power adaptor. Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory model cannot be repaired.
1-2. PRECAUTION ON REPLACING THE VC-1025 BOARD • The internal memory cannot be formatted.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”. Connect to the PC with a USB cable, (10 seconds later)
and turn on the power switch. Reactive the camcorder automatically
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
* by SEUS driver
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
If “Wireless LAN Setting (MAC address)” is not executed and the backup data before replacement is restored, the MAC address in the Wi-Fi module
does not match the MAC address in the flash memory, causing an error during Wi-Fi transfer.
Note: The “LOAD AND WRITE” function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust manual overwrites all data of the unit. Therefore,
the MAC address updated during the above procedure is also overwritten.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-1
1-3. CHECKING THE Wi-Fi FUNCTION 1-4. SELF-DIAGNOSIS FUNCTION
Perform the following procedure to check the Wi-Fi function. 1-4-1. Self-diagnosis Function 1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
Required equipment: Windows personal computer with Wi-Fi interface function starts working, and displays on the Viewfinder or the LCD Viewfinder or the LCD screen shows a 4-digit display consisting of an
screen what to do. alphabet and numbers, which blinks at 3.2 Hz. This 5-character display
1. Turn on the power of the unit. This function consists of two display; self-diagnosis display and service indicates the “repaired by:”, “block” in which the problem occurred, and
2. Perform the following operations. mode display. Details of the self-diagnosis functions are provided in the “detailed code” of the problem.
[MENU]→[Camera/Mic]→[ Shooting Assist]→[Ctrl with Smartphone] Instruction manual.
3. When preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed.
Viewfinder or LCD screen
Ctrl with Smartphone Wi-Fi
SSID DIRECT-XXXX:HDR-XXXX
Blinks at 3.2 Hz
Password XXXXXXXX
Device Name HDR-XXXX
4. Confirm on the personal computer that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection” from the icon
displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.
C 32 00
Repaired by:
Block Detailed Symptom/State Correction
Function Code
C6816
C6817
C6814
C6815
per iris initializing • Case of the iris blades do not close normally. Replace the lens block.
• Case of E: “61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
• Case of LCD is not displayed normally. Check that connection between
CN6702 on CM-1004 board and CN4004 on VC-1025 board by FP- IC6800
2190 flexible board.
• Case of LCD is displayed normally. Replace the lens block. R1401
Handshake correction function does not
Inspect PITCH angular velocity sensors (SE7701 on the JK-1009 board)
E 6 2 0 0 work well. (With PITCH angular velocity
peripheral circuits.
sensor output stopped.)
Handshake correction function does not Fig. 1
Inspect YAW angular velocity sensors (SE7701 on the JK-1009 board) Measurement points on the VC-1025 board
E 6 2 0 1 work well. (With YAW angular velocity
peripheral circuits.
sensor output stopped.)
E 6 2 0 2 Abnormality of IC for steadyshot. Refer to “1-5-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Occurred”.
IC for steadyshot and micro controller
E 6 2 0 3 Inspect the steadyshot circuit (IC7711 on the VC-1025 board).
communication abnormality among.
Image vibration correction during hand- Inspect the image vibration angular velocity sensors (SE7711 on the VC-
E 6 2 0 4
shake function does not work. 1025 board) peripheral circuits.
Replacement of lens block (Note 3). approx. 330 msec
E 6 2 1 0 Shift lens initializing failure.
If an error occurs again, replace the VC-1025 board. Note: The length of low section will vary a little depending on the conditions.
E 6 2 1 1 Shift lens overheating (Pitch) Refer to “1-5-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred”.
E 6 2 1 2 Shift lens overheating (Yaw) Refer to “1-5-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred”. Fig. 2
Change in output voltage of R1401 on the VC-1025 board
E 6 2 2 0 Abnormality of thermistor. Refer to “1-5-4. E : 62 : 20 (Abnormality of Thermistor) Occurred”.
E 6 2 3 0 Abnormal CPU Turn power off and turn power on again.
E 9 1 0 1* Abnormality when flash is being charged. Turn power off and turn power on again.
E 9 1 0 2* Abnormality of LED Video light. Turn power off and turn power on again.
Abnormality of LED Video light Tem-
E 9 1 0 3* Turn power off and turn power on again.
perature detection.
Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the
symptom is occurred after replacing the battery. If the symptom is still
Battery current value goes over the max
E 9 2 0 1 occurred, overhaul inspection is needed. Check each output of DC/DC
discharge current
converter (IC5100 on the VC-1025 board) with connected the DC JACK
(CN4007) on the VC-1025 board.
(The minimum connection to periphery)
Fault of writing or erasing the flash
E 9 4 0 0 Inspect the flash memory (IC8101 on the MM-102 board).
memory
E 9 4 0 1 Internal flash memory fault Inspect the flash memory (IC8101 on the MM-102 board).
E 9 4 0 2 BGM data error Check the CPU (IC6000 on the VC-1025 board).
E 9 5 0 0* GPS hardware error Turn power off and turn power on again.
E 9 6 0 0* Map area mount error Turn power off and turn power on again.
E 9 7 0 0 Projector hardware error Turn power off and turn power on again.
Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-3
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred 1-6. NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Order Procedure
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
1 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
2
ON to check that the output voltage immediately after the power on change as shown in Fig. 2. chart.
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect the camera When a defective part has been clarified, repair the projector according to the check result.
3
control circuit (IC6000 of VC-1025 board) periphery.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. When replacing a part of the projector unit, wait until it is cooled down.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation. Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
1-5-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
face.
Order Procedure
Projector problem checking procedure (other than indication on brightness)
1 Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SERVICE] tab.
Check if the shift lens moves while setting the order 1.
Indicated defective
2 If the shift lens does not move, replace the lens block (Note). projector received
When the shift lens moved, proceed to the order 3.
While setting the order 1, measure with an oscilloscope the output voltage of C6816 and C6817 in the periphery of IC6800 on the VC- 1 Refer to the ADJUST tab of Adjust Manual.
3 2 Refer to the SERVICE tab of Adjust Manual.
1025 board to check the output voltage varies.
No
If the output voltage does not vary, replace the lens block (Note). Indication on
4
When the output voltage varied, proceed to the order 5. brightness
5 Turn the power OFF. B
Yes (See page 1-5)
While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power
6
ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
If the output voltage rises to 3V, replace the lens block (Note). NG NG
7
If it does not rises to 3V, inspect the camera control circuit IC6000 and IC6800 on the VC-1025 board periphery. Measure brightness. A Inspect projector
( 2) LED. ( 1)
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. (See page 1-5)
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation. OK OK
- Replace projector unit (light emitting block). (*1)
- Replace PJ board. (*1)
1-5-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred - Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Order Procedure
- Fixed value input
1 Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SERVICE] tab. Enter the number on the label attached to the unit.
Check if the shift lens moves while setting the order 1. - Serial number input
2 If the shift lens does not move, replace the lens block (Note). LD40Syywwnnnnn Enter the red part.
When the shift lens moved, proceed to the order 3.
While setting the order 1, measure with an oscilloscope the output voltage of C6814 and C6815 in the periphery of IC6800 on the VC-
3 NG
1025 board to check the output voltage varies. Inspect projector
If the output voltage does not vary, replace the lens block (Note). LED. ( 1)
4
When the output voltage varied, proceed to the order 5.
OK
5 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power
6
ON to check that the output voltage immediately after the power on change as shown in Fig. 2. END
If the output voltage rises to 3V, replace the lens block (Note).
7
If it does not rises to 3V, inspect the camera control circuit IC6000 and IC6800 on the VC-1025 board periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-4
Projector problem checking procedure (indication on brightness)
Indicated defective
projector received
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
No
Indication on
brightness
B (See page 1-4)
Yes
NG
Measure brightness.
( 2)
NG
Inspect projector
LED. ( 1)
OK
NG
Measure brightness.
( 2)
OK
END
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-5E
Ver. 1.1 2014.03
The changed portions from 2. REPAIR PARTS LIST
Ver. 1.0 are shown in blue.
IDENTIFYING PARTS
(ENGLISH) The components identified by mark 0 or dotted line
Follow the disassembly in the numerical order given. NOTE: with mark 0 are critical for safety.
• -XX, -X mean standardized parts, so they may have some differences from the original Replace only with part number specified.
one. Les composants identifiés par une marque 0 sont
• Items marked “*” are not stocked since they are seldom required for routine service. critiques pour la sécurité.
Some delay should be anticipated when ordering these items. Ne les remplacer que par une pièce portant le numéro
• The mechanical parts with no reference number in the exploded views are not supplied. spécifié.
3 L top Assy 8 Control Switch Block (PS45300) • Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set. • Color Indication of Appearance Parts
PJ340/PJ340E/
• CAPACITORS: Example:
PJ350/PJ350E qg Built-In USB Cable
uF: μF (SILVER) : Cabinet’s Color
6 IM Block
• COILS (Silver) : Parts Color
• MM-102 Board
• FP-2060 Flexible Board uH: μH
• RESISTORS The components identified by mark contain confiden-
All resistors are in ohms. tial information.
9 Inner Cabinet Assy Strictly follow the instructions whenever the components
METAL: metal-film resistor
qa JK Block METAL OXIDE: Metal Oxide-film resistor are repaired and/or replaced.
• JK-1009 Board Destroy and discard the prescribed board and IC after
F: nonflammable
• FP-2191 Flexible Board they are replaced.
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...: μA... , uPA... , μPA... , Les composants identifiés par le symbole contiennent
uPB... , μPB... , μPC... , μPC... , des informations confidentielles.
7 Wi-Fi and NFC Block Suivez scrupuleusement les instructions chaque fois
uPD..., μPD...
• WF-1004 Board qu'un composant est remplacé et / ou réparé.
qf DC Jack
• NFC Block Assy Veuillez détruire et éliminer les circuits imprimés et / ou
• AN-1006 Flexible Board les circuits intégrés que vous avez remplacés.
• FP-2200 Flexible Board
q; Lens Block 标识有 的元件包含机密信息。
• CM-1004 Board 更换或维修元件时,请严格遵守指⽰。
更换后的电路板和IC,应予以报废。
• FP-2190 Flexible Board
qd Speaker
(JAPANESE) お願い
5 Microphone Cabinet Block Assy 図面番号で部品を指定するときは基板名
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付いてい 又はブロックを併せて指定してください。
る部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合があります。 0印の部品,または0印付の点線で囲まれた部品は,
• *印の部品は常備在庫しておりません。 安全性を維持するために,重要な部品です。
• コンデンサの単位でuFはμFを示します。 従って交換時は,必ず指定の部品を使用してくださ
• 抵抗の単位Ωは省略してあります。 い。
1 Cabinet (LR) Assy 金 被:金属被膜抵抗。
• 外装部品色表示
サンキン:酸化金属被膜抵抗。
qs VC-1025 Board 例:
• インダクタの単位でuHはμHを示します。
qj Cabinet (R) Assy (SILVER) :セットの色を表す。
• 半 導 体 の 名 称 でuA..., uPA..., uPB..., uPC..., uPD...等 は そ れ ぞ れ μA..., μPA...,
4 F Panel Assy (Silver) :部品の色を表す。
μPB..., μPC..., μPD...を示します。
印の部品には,秘密情報が含まれています。
修理の際は,指示に従った対応を行ってください。
qh LCD Block 交換後の対象基板及び対象ICは,破壊のうえ廃棄し
qh LCD Block • PD-1029 Board てください。
• PD-1028 Board • PJ-1009 Board
• FP-2184 Flexible Board • FP-2106 Flexible Board
• FP-2193 Flexible Board ・ Abbreviation
BR : Brazilian model View Position
CH : Chinese model
Top View
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korea model Left View Back View
NE : North European Model
機種によって形状がイラストと異なる場合があります。
Right View
Front View
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-1
– ENGLISH – – JAPANESE –
OK NG NG
OK NG NG
(The flexible board was plugged in straight (The flexible board was plugged in (The flexible board was not plugged in
(奥までまっすぐに差し込んである) (斜めに差し込んである) (差し込み不十分)
and completely) crooked.) completely.)
Flexible Flexible フレキシブル フレキシブル フレキシブル
Board Flexible Flexible Board フレキシブル 基板
Flexible 基板 基板 フレキシブル
Board Board 基板 基準線 基板
Reference line Flexible Reference line Board 基準線
フレキシブル
Reference line Board 基準線 基板
Connector Connector Connector Connector Connector Connector コネクター コネクター コネクター コネクター コネクター コネクター
When opening the connector's holder in direction A, do not open When closing the connector's holder, press it evenly while pushing コネクターの開閉部を開ける際,A方向に開け過ぎないようにし コネクターの開閉部を閉じる際,フレキシブル基板を矢印B方向
it with excessive force. a flexible board in direction B. てください。 に押しながら,開閉部を均一に押してください。
Holder Holder 開閉部 開閉部
A Connector A コネクター
Flexible Board フレキシブル基板
Connector コネクター
A Flexible Board A フレキシブル基板
B B
• Make sure that the flat cable and flexible board are not cracked Cut and remove the part of gilt • フラットケーブルおよびフレキシブル基板の端子面に欠け, 先端の剥がれたメッキ部はカットして
or bent at the contact end. which comes off at the point. 折れ等がないことを確認してください。 除去してください。
(Be careful or some (メッキ破片がコネクター内に残って
• Do not apply excessive force to the gilded flexible board. pieces of gilt may be left inside) • 金メッキされているフレキシブル基板には,強い負担をかけ いる場合もあるので注意してください)
ないでください。
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-2
2-1. EXPLODED VIEWS DISASSEMBLY
2-1-1. OVERALL SECTION 1. Remove in numerical order (1 to 3) in the left figure.
#12
(Claws)
ns
#12
1 #2
#12
A
3 #2 X 1 → #12 X 2→ #2 X 2 → #12 X 1
#12
Right View Left View Bottom View
#2 #2
#12
#12
33 #2
#2
Projector
Model (Claw)
A #12
#12
22
#2
Screw
#2: M1.7 X 4.0 #12: M1.7 X 5.0 (Tapping)
(Black) (Black)
2-635-562-31 3-080-204-21
1.7 1.7
Non Projector
4.0 5.0
Model
(Claw)
Front Section 1
21 (See page 2-4)
Ref. No. Part No. Description Ref. No. Part No. Description
1 4-476-678-01 COVER (R (449)), HINGE (Non Projector Model) 3 A-1998-399-A LTOP ASSY (444W) (WHITE)
2 4-476-677-01 COVER (R (4441)), HINGE (Projector Model) (BLACK) 3 A-1998-400-A LTOP ASSY (444L) (BLUE)
2 4-476-677-11 COVER (R (4441)), HINGE (WHITE) 4 A-1998-352-A CABINET (LR) ASSY (449B) (BLACK, BLUE)
2 4-476-677-21 COVER (R (4441)), HINGE (BLUE) 4 A-1998-354-A CABINET (LR) ASSY (449W) (WHITE)
3 A-1998-398-A LTOP ASSY (444B) (BLACK)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-3
2-1-2. FRONT SECTION
DISASSEMBLY
ns: not supplied
1. Remove in numerical order (1 to 2) in the left figure.
2 #12 X 1
1 54
Left View
ns #12
2 51
Screw
#11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping)
(Silver) (Black)
3-078-890-11 3-080-204-21
ns
1.7 1.7
ns
ns
ns 53
ns
(Claw)
#11 MIC901
52
#11
Lens Section
(See page 2-5)
Ref. No. Part No. Description Ref. No. Part No. Description
51 A-1998-367-A CABINET BLOCK ASSY, MICROPHONE MIC901 1-542-999-21 MICROPHONE UNIT
52 4-447-694-01 CUSHION, MIC
* 53 4-533-725-01 SHEET (WF (453)), SHIELD #11 3-078-890-11 SCREW, TAPPING
54 A-1998-402-A PANEL ASSY (444), F #12 3-080-204-21 SCREW, TAPPING, P2
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-4
Ver. 1.1 2014.03
The changed portions from
Ver. 1.0 are shown in blue.
#12
#12 #2
#140
#12
#140
Top View
1 113
#2
#140
B B
112
C
PJ340/PJ340E/PJ350/PJ350E 4 #2 X 1 → #12 X 1 5 #172 X 2
Cabinet (R) Section Right View Top View #12 Left View
#2
(See page 2-6)
4 115
#172
111
110
109 #172
(Note 3)
#172
Screw
C 104
#2: M1.7 X 4.0 #12: M1.7 X 5.0 (Tapping) #140: M1.7X 2.0 #172: M1.4 X 4.0 (Tapping)
(including CP001
(Black) (Black) (Black) (Black)
#140 (CMOS imager)) 2-635-562-31 3-080-204-21 2-635-562-01 2-178-410-01
(Note 1)
108
106 103 1.7 1.7 1.7 1.4
Note
Note 1: Be sure to read “Precautions for Replacement of Imager” Note 1: イメージャの交換時はLevel 3の6-1ページ, イメージャ交
on page 6-1 of Level 3 when changing the imager. 換時の注意 を必ずお読みください。
Ref. No. Part No. Description Ref. No. Part No. Description
101 8-848-900-01 DEVICE, LENS LSV-1610A 111 4-274-987-01 TAPE (AS 1/2) (C)
Note 2: Refer to “Assembly-2: How to distinguish the side of Optical Note 2: Assembly-2: How to distinguish the side of Optical Filter
102 1-856-432-21 FILTER BLOCK, OPTICAL (Note 2) 112 1-887-155-11 FP-2060 FLEXIBLE BOARD (PJ340/PJ340E/PJ350/
Filter Block facing to Lens Device”. Block facing to Lens Device を参照してください。
103 4-436-733-01 RUBBER (1610), SEAL PJ350E)
104 A-1903-090-A CM-1004 BOARD, COMPLETE (including CP001 113 A-1992-197-A MM-102 BOARD, COMPLETE (PJ350/PJ350E)
(CMOS imager)) (Note 1) 113 A-1994-766-A MM-102 BOARD, COMPLETE (PJ340/PJ340E) Note 3: Be careful not to break the NFC Block Assy. Note 3: NFC部組を折らないよう注意してください。
105 1-889-184-11 FP-2190 FLEXIBLE BOARD 114 1-492-709-11 SWITCH BLOCK, CONTROL (PS45300)
106 1-889-592-11 AN-1006 FLEXIBLE BOARD 115 A-1998-288-A CABINET ASSY (449), INNER
107 A-1992-200-A WF-1004 BOARD, COMPLETE
108 1-889-209-11 FP-2200 FLEXIBLE BOARD #2 2-635-562-31 SCREW(M1.7)
109 A-2040-416-A NFC BLOCK ASSY (14Y_TERA) COMP (Note 3) #12 3-080-204-21 SCREW, TAPPING, P2
110 4-489-010-01 SHEET (ANT), ADHESIVE #140 2-635-562-01 SCREW (M1.7)
#172 2-178-410-01 TITE (UB TITE) 1.4
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-5
2-1-4. CABINET (R) SECTION
DISASSEMBLY
ns: not supplied
1. Remove in numerical order (1 to 3) in the left figure.
#12
#12 #2 2 #12
157 A
Left View
B
ns #2
#288
J901
Screw
#2: M1.7 X 4.0 #12: M1.7 X 5.0 (Tapping) #288: M1.7 X 2.5
(Black) (Black) (Black)
158 2-635-562-31 3-080-204-21 2-187-345-21
(Note 2)
153 Non Projector 1.7 1.7 1.7
#12 #288 Model
(Note 1)
A #2 4.0 5.0 2.5
152
Note
B
Note 1: This screw cannot be reused. Discard the screw removed Note 1: このねじは再利用することができません。サービス対応時
once in servicing. Instead, use a new screw. に一度でも外した場合は新品のねじと交換してください。
Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1994-767-A VC-1025 BOARD, COMPLETE (SERVICE) 157 A-1998-390-A CABINET (R) ASSY (444) (Non Projector Model)
(Non Projector Model) 157 A-1998-391-A CABINET (R) ASSY (4441) (Projector Model)
151 A-1994-768-A VC-1025 BOARD, COMPLETE (SERVICE) 158 3-283-643-21 SCREW, TRIPOD (Note 2)
(Projector Model)
152 1-838-712-32 CABLE, BUILT-IN USB J901 1-842-658-71 JACK, DC
153 4-476-262-01 RETAINER (453), HDMI SP901 1-858-075-41 SPEAKER (1.8CM)
154 1-889-185-11 FP-2191 FLEXIBLE BOARD
#2 2-635-562-31 SCREW(M1.7)
155 A-1994-762-A JK-1009 BOARD, COMPLETE #12 3-080-204-21 SCREW, TAPPING, P2
* 156 3-283-835-01 CUSHION, SP #288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-6
Ver. 1.1 2014.03
The changed portions from
Ver. 1.0 are shown in blue.
220 #288
(Note 3) (Note 2) #2 1.7 1.7 1.2 1.7
219
218
216 (Note 5)
Note
(Claws) B 217
213 Note 1: Replace the battery holder (BH4600) together when replac- Note 1: PD-1029基板のリチウム蓄電池(BT4600) を交換する場合は
214 バッテリホルダ(BH4600) も同時に新品に交換してくださ
206 ing the lithium storage battery (BT4600) on the PD-1029
Adjust the position. board. い。
B (一度使用したバッテリホルダは再使用できません。)
D (The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first 部品取り付けの際は,先にバッテリホルダを取り付けてか
#11 LCD901 and attach new lithium storage battery next. らリチウム蓄電池を装着してください。
212 Note 2: This screw cannot be reused. Discard the screw removed Note 2: このねじは再利用することができません。サービス対応時
once in servicing. Instead, use a new screw. に一度でも外した場合は新品のねじと交換してください。
D ns 209 211 Note 3: Refer to “Assembly-1: Installation Method of FP-2184/FP- Note 3: Assembly-1: Installation Method of FP-2184/FP-2193 を参
204 2193”. 照してください。
BH4600 208
C
(Note 1) C Note 4 Note 4
BT4600 205 PRECAUTIONS WHEN HOLDING THE PROJECTOR UNIT プロジェクターユニットを持つ際の注意
(Note 1) 221
A (Note 4) Very weak Weak Have to wear 非常に弱い 弱い 指サック着用
(Don't hold) (Handling attention) finger stall のこと
207 #11
#2 Lever Contact area of レバー フレキ接点
レンズ部 銅板
Lens part Copper Plate Flexible Board
203
: BT4600 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-54 of Level 3) 202 #30
222 Sheet Copper Plate Terminal of シート 銅板 コネクタ部
Connector
(Claws) プロジェクターを使用した後は,プロジェクターユニットが熱くなっています。
The projector unit (copper plate in particular) becomes hot after it is used. 特に銅板の部分は高温になります。
201 When replacing a part of the projector unit, wait until it is cooled down. 部品を交換する時は,温度が下がってから作業を行なってください。
Ref. No. Part No. Description Ref. No. Part No. Description Note 5: Install the magnet with Note 5: マグネットを取付ける
the marking oriented 際は,マ−キング面を
201 A-1998-404-A CABINET (C) ASSY (4441B), P (PJ340 (BLACK)/ 214 4-476-572-01 BUTTON (4411), PLAYBACK (PJ) as shown below. 図の位置にあわせて
PJ340E (BLACK)) 215 4-476-561-01 CABINET (M (4441)), P ください。
201 A-1998-405-A CABINET (C) ASSY (4441W), P (WHITE) 216 4-476-671-01 COVER (C (4441)), HINGE (BLACK)
201 A-1998-410-A CABINET (C) ASSY (4441L), P (BLUE)
201 A-1998-411-A CABINET (C) ASSY (4441B), P (PJ350/PJ350E) 216 4-476-671-11 COVER (C (4441)), HINGE (WHITE)
201 A-1998-412-A CABINET (C) ASSY (4441B), P (PJ330E) 216 4-476-671-21 COVER (C (4441)), HINGE (BLUE)
217 X-2585-820-2 HINGE (P) (Y (4071)) ASSY
202 4-476-581-01 HEAT SINK (4441), P 218 1-471-573-11 MAGNET (Note 5)
Marking マーキング
203 A-1903-100-A FP-2106 FLEXIBLE BOARD, COMPLETE 219 4-476-570-01 COVER (M (4441)), HINGE
204 4-272-358-01 CUSHION, P
205 A-1847-133-A LSV-1580A (Note 4) 220 1-889-187-11 FP-2193 FLEXIBLE BOARD (Note 3)
206 A-1994-765-A PJ-1009 BOARD, COMPLETE 221 4-272-354-01 SHEET, P RADIATION
222 4-476-583-01 SHEET PJ (4441)
207 A-1994-888-A PD-1029 BOARD, COMPLETE (SERVICE)
208 4-209-715-01 JOYSTICK BH4600 1-251-928-21 SOCKET, BATTERY (Note 1)
209 4-476-577-01 INSULATING SHEET (4441) BT4600 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
210 4-476-573-01 KNOB (4441), FOCUS LCD901 1-811-218-31 LCD MODULE
211 4-476-580-01 RETAINER (4441), LCD
#2 2-635-562-31 SCREW (M1.7)
212 4-476-566-01 CUSHION (4441), LCD #11 3-078-890-11 SCREW, TAPPING
213 4-476-579-01 PLATE (4441), PANEL GROUND #30 3-086-156-11 SCREW B1.2
#288 2-187-345-21 SCREW (M1.7), P2 (Note 2)
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-7
2-1-6. MOUNT SECTION
(Non Projector Model)
Screw
Refer to page 2-7 about Projector Model. #2: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #288: M1.7 X 2.5
(Black) (Silver) (Black)
ns: not supplied 2-635-562-31 3-078-890-11 2-187-345-21
263
(Note 3) #288 #2
(Note 2)
Note
262
Note 1: Replace the battery holder (BH4500) together when replac- Note 1: PD-1028基板のリチウム蓄電池(BT4500) を交換する場合は
261 ing the lithium storage battery (BT4500) on the PD-1028 バッテリホルダ(BH4500) も同時に新品に交換してくださ
(Note 4) board. い。
260 (The battery holder removed once cannot be used again.) (一度使用したバッテリホルダは再使用できません。)
When mounting these parts, mount new battery holder first 部品取り付けの際は,先にバッテリホルダを取り付けてか
(Claws) and attach new lithium storage battery next. らリチウム蓄電池を装着してください。
259 257 Note 2: This screw cannot be reused. Discard the screw removed Note 2: このねじは再利用することができません。サービス対応時
once in servicing. Instead, use a new screw. に一度でも外した場合は新品のねじと交換してください。
LCD901 256
Note 3: Refer to “Assembly-1: Installation Method of FP-2184/FP- Note 3: Assembly-1: Installation Method of FP-2184/FP-2193 を参
2193”. 照してください。
253
#11
ns 254
Marking マーキング
252
A
#2
BH4500
(Note 1)
BT4500
(Note 1)
Ref. No. Part No. Description Ref. No. Part No. Description
251 4-476-667-01 CABINET (C (449)), P 261 1-471-573-11 MAGNET (Note 4)
252 4-274-987-01 TAPE (AS 1/2) (C) 262 4-476-560-01 COVER (M (449)), HINGE
253 A-1994-877-A PD-1028 BOARD, COMPLETE (SERVICE) 263 1-889-097-11 FP-2184 FLEXIBLE BOARD (Note 3)
254 4-209-715-01 JOYSTICK
255 4-446-970-01 INSULATING SHEET (409) BH4500 1-251-928-21 SOCKET, BATTERY (Note 1)
BT4500 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
256 4-476-576-01 PLATE (441), PANEL GROUND LCD901 1-811-218-31 LCD MODULE
257 4-476-572-11 BUTTON (4411), PLAYBACK (PJ)
258 4-476-562-01 CABINET (M (444)), P #2 2-635-562-31 SCREW(M1.7)
259 4-476-672-01 COVER (C (449)), HINGE #11 3-078-890-11 SCREW, TAPPING
260 X-2585-819-1 HINGE (Y (409)) ASSY, T TYPE #288 2-187-345-21 SCREW (M1.7), P2 (Note 2)
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-8
ACCESSORIES
901 902 903 904 905 This Item is not supplied with the unit as an accessory, but it is prepared as a service part.
When the customer requests printed one, ask Head Quarter.
941
Ref. No. Part No. Description Ref. No. Part No. Description
901 1-492-768-12 AC Adaptor (US, CND, JE, E: NTSC) * 905 4-531-077-11 Operating Guide (GERMAN, DUTCH, ITALIAN,
901 1-492-768-21 AC Adaptor (CH) PORTUGUESE) Ref. No. Part No. Description Ref. No. Part No. Description
901 1-492-769-11 AC Adaptor (AEP, NE, E: PAL) * 905 4-531-077-21 Operating Guide (GREEK, POLISH, CZECH, * 941 4-531-073-11 Help Guide (ENGLISH) * 941 4-531-074-71 Help Guide (DANISH)
901 1-492-769-21 AC Adaptor (BR) HUNGARIAN) * 941 4-531-073-21 Help Guide (FRENCH) * 941 4-531-074-81 Help Guide (FINNISH)
901 1-492-769-31 AC Adaptor (KR) * 905 4-531-077-31 Operating Guide (SLOVAK, SWEDISH, DANISH, * 941 4-531-073-31 Help Guide (SPANISH) * 941 4-531-074-91 Help Guide (ROMANIAN)
FINNISH, ROMANIAN) * 941 4-531-073-41 Help Guide (GERMAN) * 941 4-531-075-11 Help Guide (RUSSIAN)
901 1-492-771-11 AC Adaptor (UK, HK) * 941 4-531-073-51 Help Guide (ITALIAN) * 941 4-531-075-21 Help Guide (UKRAINIAN)
902 1-569-007-12 Conversion (2P) Adaptor (E: NTSC, JE) * 905 4-531-077-41 Operating Guide (RUSSIAN)
903 1-838-714-31 USB connection support cable * 905 4-531-077-51 Operating Guide (UKRAINIAN) * 941 4-531-073-61 Help Guide (DUTCH) * 941 4-531-075-31 Help Guide (TRADITIONAL CHINESE)
904 1-846-028-21 HDMI cable * 905 4-531-077-61 Operating Guide (SIMPLIFIED CHINESE) * 941 4-531-073-71 Help Guide (PORTUGUESE) * 941 4-531-075-41 Help Guide (SIMPLIFIED CHINESE)
* 905 4-529-735-11 Operating Guide (ENGLISH) * 905 4-531-077-71 Operating Guide (ARABIC, PERSIAN) * 941 4-531-073-81 Help Guide (BRAZILIAN PORTUGUESE) * 941 4-531-075-51 Help Guide (KOREAN)
* 905 4-531-077-81 Operating Guide (TURKISH) * 941 4-531-073-91 Help Guide (TURKISH) * 941 4-531-075-61 Help Guide (ARABIC)
* 905 4-529-735-21 Operating Guide (SPANISH) * 941 4-531-074-11 Help Guide (GREEK) * 941 4-531-075-71 Help Guide (PERSIAN)
* 905 4-529-735-41 Operating Guide (TRADITIONAL CHINESE) * 905 4-531-078-31 Operating Guide (SIMPLIFIED CHINESE)
* 905 4-531-076-21 Operating Guide (KOREAN) * 941 4-531-074-21 Help Guide (CZECH) * 941 4-531-075-81 Help Guide (INDONESIAN)
* 941 4-531-074-31 Help Guide (HUNGARIAN) * 941 4-531-075-91 Help Guide (THAI)
* 941 4-531-074-41 Help Guide (SLOVAK)
* 941 4-531-074-51 Help Guide (POLISH)
* 941 4-531-074-61 Help Guide (SWEDISH)
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-9E
3. ASSEMBLY
Assembly-1: The Method of attachment of FP-2184/FP-2193 Assembly-2: How to distinguish the side of Optical Filter Block
Flexible Board facing to Lens Device
1 Fold dotted line parts of the FP-2184/FP-2193 flexible 2 Roll the FP-2184/FP-2193 Flexible Board 2 times The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
board as shown in figure. in the Hinge Assy as shown in figure. device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
Adhesive tape outside light).
Adhesive tape
Adhesive tape Valley fold Flexible Board
Mountain fold
Mountain fold
Adhesive tape
Hinge Assy
Adhesive tape 2 Times [IR Cut Coated Side] [The Other Side]
Lens Device side • The other surface
3 Install the Cover (M) Hinge/Cover (C) Hinge. The red coating is
not reflected. • Side view
Cover (M) Hinge The red belt
is seen.
FP-2184/FP-2193
Flexible Board
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
3-1E
7. ADJUSTMENT
(ENGLISH)
For adjusting these models, the Adjust manual and the Adjust station are required.
Adjust station
It is the software to start up Adjust manual for each model.
The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them.
Adjust manual
It is the software to adjust and check digital cameras and camcorders for service.
The installer of the Adjust manual and the installation manual are attached, be sure to confirm the contents of them.
(JAPANESE)
これらの機種で調整を行なうには,アジャストマニュアルとアジャストステーションが必要です。
アジャストステーションとは
機種別のアジャストマニュアルを起動するためのソフトウェアです。
アジャストステーションのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認してくださ
い。
アジャストマニュアルとは
デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで,調整及び各種動作確認を行うことが可能です。
アジャストマニュアルのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認してください。
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
7-1E