Professional Documents
Culture Documents
Harold A. Abella - Cbc-Reviewer For Btled Major
Harold A. Abella - Cbc-Reviewer For Btled Major
I. Directions: Read and analyze the sentences carefully. Choose the letter that
corresponds to the best answer.
INDUSTRIAL ARTS
1. What is the total resistance of five resistors connected in series with a value of 20
ohms each?
A. 100 ohms B. 4 ohms C. 10 ohms D. .0.4 ohms
2. An electromotive force that drives the electrons to flow along the conductor.
A. Current B. Power C. Resistance D. Voltage
4. What is the power dissipated by a circuit connected across a 240 volts’ source with a
measured current of 1.2 amperes?
A. 200 watts B. 288 watts C. 0.005 watts D. 20 watts
5. What is the voltage required in a circuit with 20 pieces of 12 volts’ lamps connected in
parallel?
A. 240 volts B. 120 volts C. 24 volts D. 12volts
6. What is the standard size of wire to be used for convenience outlet circuit?
A. 2.0 sq.mm. B. 8.0 sq.mm. C. 3.5 sq.mm. D. 5.4 sq.mm.
7. What is the required size of branch circuit breaker for lighting circuit?
A. 15A (/) B. 20A C. 30A D. 60A
8. It is a device that is used for controlling the flow of electric current in a circuit.
A. Lamp B. Switch (/) C. Receptacle D. Outlet
9. What is the current flowing in a 3.6 kilowatts circuit with a 25 ohms’ resistive load?
A. 144 Amp. B. 12Amp (/) C. 1.44 Amp D. 1.2 Amp
11. Which of the following logical operations is represented by the + sign in Boolean
algebra?
A. Inversion B. AND C. OR D. Complementation
12. An output will be a LOW for any case when one or more inputs are zero for a(n):
_______.
A. OR gate B. NOT gate C. AND gate D. NOR gate
14. What is the unit of measure for electrical pressure or electromotive force?
A. amps B. ohms C. volts D. watts
15. Which of the following circuit configurations has the same amount of voltage drop
across each of its components?
A. parallel B. series-parallel C. series D. combination
21. It is the term applied to the operation performed in preparing wood for commercial
purposes.
A. Wood B. Lumbering C. Soft wood D. Hard wood
22. It is an art of building with stone, bricks, concrete blocks or similar.
A. Welding B. Carpentry C. Plumbing D. Masonry
23. It is a type of service where Foods are on the long buffet table where the diners
serve themselves.
a. Buffet service c. American service
b. English service d. Table service
24. It came from plant where the threadlike substances are extracted.
A. Fabric B. Thread C. Fiber D. Cloth
25. Flower is said to be perfect when it contains both male and female part.
A. Male B. Bisexual C. Female D. Unsexual
26. It takes place when pollen grains are transferred from an anther to the stigma of
same flower.
A. Homogamy B. Hierogamy C. Autogamy D. Allogamy
27. It refers to the kind of steel that has special additives that make it strong, flexible,
ductile, wear resistant, etc.
A. Metal sheet B. Aluminum C. Copper D. Alloy steel
28. It is when the edge of two plates butt up to each other at a 90 degrees’ angle.
A. Edge joint B. Corner joint C. Tee joint D. Mortise and tendon
29. Grow on another plant from which it takes part or all nourishment.
A. Parasitic plant C. Terrestrial plant
B. Aquatic plant D. Halophytic plant
30. The type of soil that are highly moisture and retentive.
A. Red soil C. clayey soil
B. Black soil D. sandy soil
31. The following reasons why a drawing pencil is better than an ordinary writing pencil
except.
A. There are different kinds of drawing pencils for specific work.
B. Drawing pencils are made of a much better grade of graphite called LEAD.
C. It is possible to draw lines of uniform blackness.
D. Drawing pencils are more expensive so they produced better result.
32. The following statements are good to follow when making lettering except.
A. Vertical lines are drawn lightly and are spaced accordingly.
B. When lowercase letter is used, the capital letter is used for the beginning
letter.
C. When using lowercase, only two horizontal guidelines are used.
D. When performing uppercase letters used cap and base lines as major lines.
33. When you want to indicate the center of holes of an object to be made in the
drawing, which of the following lines will you used.
A. Hidden lines B. Long break lines C. Center lines D. Section lines
36. A line used to represent the visible edges of an object when making a drawing.
A. Hidden line B. Object line C. Section line D. Long break line
37. Which of the following kinds of drawing is used to show the front, top and side view
of an object in their actual relation to each other.
A. Isometric drawing C. Elevation drawing
B. Oblique drawing D. Perspective drawing
38. The kind of drawing which shows how object actually appears to the observer.
A. Isometric B. oblique C. Elevation D. Perspective
43. It is a device that supplies the engine with the right amount of air and fuel.
A. Radiator B. Battery C. Alternator D. Carburetor
44. It is a device which engages and disengages the transmission from the engine.
A. Clutch B. Transmission C. Driveshaft D. Differential
45. It is the system that supplies engine parts with lubricating oil.
A. Fuel System C. Steering System
B. Lubrication System D. Cooling System
46. It is the device that transmits the power generated by the engine to the drive wheels
of your car via the axle.
A. Clutch B. Transmission C. Driveshaft D. Differential
47. It is the mechanism that enables the driver to control the direction of vehicle travel.
A. Steering Wheel C. Steering System
B. Steering Column D. Axle Shaft
48. It is a device or gear assembly between two shafts that permits the shafts to turn at
different speeds.
A. Differential B. Drivelines C. Clutch D. Transmission
49. It is a system which keeps the engine within its normal operating temperature.
A. Lubrication System C. Cooling System
B. Brake system D. Fuel System
AGRI-FISHERY
51. It is a method of fish preservation to empty space without air.
a. Vacuum b. Pickling c. Canning d. Dehydration
53. A fillet from side of a fish cut away from the backbone.
a. Autolysis b. Pickling c. Single fillet d. Double fillet
54. It is a fuzzy or cottony organisms that grow on the surface of the food.
a. Molds b. Brine c. Canning d. Dehydration
55. It is the process of food so that they can be stored for a longtime.
a. Preservation b. Pickling c. Canning d. Dehydration
63. It is the science which also include the art of growing plants.
a. Xerophytes b. Horticulture c. Parasitic Plants d. Land Plants
64. It is the smallest particle amongst the other two types of soil.
a. Clay soil b. Sandy Soil c. Black Soil d. Loamy Soil
65. They grow on another plant from which it takes part or all nourishment.
a. Xerophytes b. Horticulture c. Parasitic Plants d. Land Plants
66. Most agricultural crops are terrestrial plants otherwise known as __________.
a. Aquatic Plants b. Plants c. Parasitic Plants d. Land Plants
73. PAINTING is the process or art of using pencil, in a picture, as a protective coating,
or as decoration.
a. True
b. False, it is the process or art of using paint
c. False, it is the process or art using charcoal
d. False, it is the process or art using graphite
74. Graphic Process may be classified by nature of surfaces from which printing is done,
which of the following is NOT included?
1. Relief printing
2. Printing press
3. Intaglio printing
4. Surface printing
5. Engraving
6. Etching
a. 2,4,6
b. 1,3,5
c. 1,3,4
d. 2,5,6
75. The art application and practice of creating durable images by recording light, either
electronically by means of an image sensor, or chemically by means of a light-sensitive
material.
a. Photography
b. Printing
c. Etching
d. Engraving
76. A process consisting of cutting or etching a printing surface in such a way that all
that remains of the original surface is the design to be printed
a. Printing press
b. Relief printing
c. Intaglio printing
d. Printing
79. Inspired by nature, this style of art was popular in the 1880’s. It used organic
shapes, asymmetrical line shapes instead of solid, uniform shapes
a. art deco
b. art nouveau
c. bauhaus
d. pop art
80. It combines arts and crafts, classical and avant-garde styles, form and functions
a. art nouveau
b. pop art
c. bauhaus
d. art deco
81. It is the method of printing that involves inking your design into a stone or metal
surface and transferring it to a sheet of paper.
a. lithography
b. printing press
c. heat press printing
d. chromolithography
82. It is a machine which transfers text and images onto paper though the process of
pressing ink onto paper using moveable, reusable metal type
a. Printing Press
b. Engraving
c. Typography
d. Lithograph
83. A family of printing methods where a printing block, plate or matrix that has had ink
applied to its surface, but not to any recessed areas, is brought into contact with paper.
a. Gravure
b. Relief
c. Embossing
d. Print
84. Graphic designing is a creative process that combines ________ and ________ to
communicate ideas using a skillful combination of text and pictures in advertisements,
magazines, flyers, business cards, etc.
a. art and technology
b. computers and pictures
c. computers and text
d. art and paper
86. It is a tool which has a box wrench on one end and an open-end wrench to the
other.
a. Box Wrench c. Combination Wrench
b. Open end wrench d. Torque Wrench
87. It is a tool used to turn bolts and nuts on the surfaces, and in recesses which
other wrenches cannot reach.
a. Socket Wrench c. Allen Wrench
b. Spark Plug Wrench d. Combination Wrench
90. It a tool for setting and adjusting the tightness of nuts and bolts to a desired value.
a. Torque Wrench c. Spark Plug Wrench
b. Box Wrench d. Setscrew Wrench
95. It is a device which engage and disengage the transmission from the engine.
a. Flywheel c. Friction Disc
b. Pilot Bearing d. Brake Pad
97. It is a device used to determine and get the exact timing of an engine.
a. Timing Light c. Feeler Gauge
b. Compression Tester d. Ammeter
98. It is an instrument for measuring the pressure produced by oil pump, fuel pump and
other pressure devices.
a. Tire Gauge c. Hydrometer
b. Pressure Gauge d. Voltmeter