Professional Documents
Culture Documents
IPD AutoclaveEngineers Subsea Ball Valves Catalog
IPD AutoclaveEngineers Subsea Ball Valves Catalog
Principle of Operation:
Parker Autoclave Engineers subsea ball valves have been designed in accordance with ASME B31.3 Chapter IX High
Pressure piping standards to fulfill the ever growing subsea applications in the petroleum industry as well as the need
for externally pressurized components in other markets. Utilizing the same design technology as the standard ball
valve, the subsea design incorporates the necessary design alterations to provide a reliable externally pressurized
valve for the subsea industry.
Parker Autoclave Engineers has the most connection options available and all the associated tubing, fittings and
adapters you would need to outfit any application you might have, above or below the surface. Traceability is ensured
by use of heat and purchase order codes etched on valve body that also includes model number, pressure rating, and
material type references.
Subsea ball valves are designed to facilitate opera- Subsea Actuation Torque
tion by a Remote Operated vehicle (ROV). No handle
or valve stop is provided as standard in preparation for 2 Way Subsea Ball Valve Breakout Torque Running Torque
mating to an ROV acceptable actuator. ROV operator
1/4" Orifice Stem @ 20,000 psi 75 in-lbf (9 Nm) 70 in-lbf (9 Nm)
assemblies are used for valve mounting and to provide
3/8" Orifice Stem @ 20,000 psi 275 in-lbf (31 Nm) 150 in-lbf (17 Nm)
positive valve stop for precise 90° operation.
1/2" Orifice Stem @ 15,000 psi 690 in-lbf (78 Nm) 425 in-lbf (48 Nm)
3/4" Orifice Stem @ 15,000 psi 140 ft-lb (190 Nm) 90 ft-lb (122 Nm)
1" Orifice Stem @ 10,000 psi 200 ft-lb (271 Nm) 150 ft-lb (203 Nm)
2
Ball Valves: Subsea Series 02-0108SE 0318
2 Way Subsea Series: 1/4" (6.35mm) Orifice
Pressures to 20,000 psi (1379 bar)
PACKING GLAND
15000
(1034) LOCKING PIECE
Pressure PSIG (Bar)
5000
(345)
Pressure Ratings are determined by the end connections chosen, see chart.
Maximum Temperature rating is determined by the o-ring material. To ensure proper fit use Parker Autoclave tubing
PAE Ball Valves are designed to be used in fully open or fully closed position.
NPT connections are limited to 400°F max due to PTFE Sealant.
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
3
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 2-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
F - Options
D - Pressure (x 1000 psi) V FKM material: 0° to 400°F (-18° to 204°C)
5 15,000 psi EPR Ethylene Propylene Rubber: -20° to 250°F (-29° to 121°C)
20 20,000 psi SOG NACE Material, Hardness Verification/Certificate
IN625 UNS N06625 Inconel 625 Materials
All Parts (including collar and gland) optional to use with special
AP
materials
K Antivibration Gland Fitting (Cone and Thread Connections only)
H Handle/Handle Stop
4
Ball Valves: Subsea Series 02-0108SE 0318
1/4" 2 Way Subsea Ball Valve Dimensions:
1.50
(38.1) 1/4-20 THD
0.75
(19.1)
0.50
(12.7)
0.81 HEX
1.00 (20.6)
(25.4)
0.50 FLAT LG
(12.7) 0.216 ± 0.001 FLAT
(5.48 ± .025)
12 Ø 0.249 ± 0.001
(6.32 ± .025)
1.27
(32.4)
15
8
Ø 0.28
0.25
(6.4) 14
(7.1)
3
0.43
2 (10.9)
13
1 1.50
4.31
(109.3)
(38.1)
6
5 11
SEE END
CONNECTION
7 OPTIONS
(both ends)
16 1.19
(30.2)
SEE SEAT
GLAND HEX
HEX
4 0.31 10
(7.7)
2.00
(50.8)
4.18
(106.3)
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 12,500 FT (3810 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,500 psi (379 bar) is ordered.
5
Ball Valves: Subsea Series 02-0108SE 0318
2 Way Subsea Series: 3/8" (9.52mm) Orifice
Pressures to 20,000 psi (1379 bar)
PACKING GLAND
15000 THRUST WASHER LOCKING PIECE
(1034)
Pressure PSIG (Bar)
5000
(345)
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
6
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 2-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
7
Ball Valves: Subsea Series 02-0108SE 0318
3/8" 2 Way Subsea Ball Valve Dimensions:
2.50
(63.5)
1.25
(31.8)
0.69
(17.5)
1.38
0.88 (34.9)
(22.3) BODY
THICKNESS
14 15
0.44
4 (11.1)
0.44
1.03 (26.2)
8
(26.2)
2 13
5.78
1
(146.8)
5
1.78
16
(45.2)
3
3.28
7 (83.3)
6
12 SEE END
CONNECTION
11 OPTIONS
(both ends)
1.75” HEX
(44.5)
9 0.76
SEE SEAT
GLAND HEX
(19.2)
10 3.00
(76.2)
5.53
(140.3)
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 11,500 FT (3505 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,500 psi (379 bar) is ordered.
8
Ball Valves: Subsea Series 02-0108SE 0318
2 Way Subsea Series: 1/2" (12.7mm) Orifice
Pressures to 15,000 psi (1034 bar)
O-RING
10000 SPRING
(690) QS & NPT Connection ENERGIZED PEEK SEATS
SEAL
SEAT GLAND
5000
(345)
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
9
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 2-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
10
Ball Valves: Subsea Series 02-0108SE 0318
1/2" 2 Way Subsea Ball Valve Dimensions:
3.00
(76.2)
0.50
(12.7) 1.75
1.00 (44.5)
(25.4) BODY
THICKNESS
Ø 1.50 1.50
(38.1) (38.1)
13 2
0.438 ± 0.001 SQUARE
0.88 (11.13 ± 0.021)
9 (22.2)
3
14 Ø 0.62
(15.9)
5
0.77
(19.6)
8 4
0.44
(11.1)
6.44
(163.5)
2.08
7
(52.8)
1
4.00
(101.6)
15
SEE END
CONNECTION
OPTIONS
12 (both ends)
10
SEE SEAT
GLAND HEX
2.25 HEX
6
(57.2)
11 0.88
(22.4)
16
12 4.13
(104.8)
7.73
14
(196.4)
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 11,500 FT (3505 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,500 psi (379 bar) is ordered.
11
Ball Valves: Subsea Series 02-0108SE 0318
2 Way Subsea Series: 3/4" (19mm) Orifice
Pressures to 15,000 psi (1034 bar)
O-RING
10000
(690) SPRING
NPT Connection PEEK SEATS
ENERGIZED
SEAL
SEAT GLAND
5000
(345)
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
12
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 2-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
13
Ball Valves: Subsea Series 02-0108SE 0318
3/4" 2 Way Subsea Ball Valve Dimensions:
15 5
3
19
0
10
11 9
1
20
8
17 7
4
16 12
6 2
18 14
13
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 11,500 FT (3505 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,000 psi (379 bar) is ordered.
14
Ball Valves: Subsea Series 02-0108SE 0318
2 Way Subsea Series: 1" (15.4mm) Orifice
Pressures to 10,000 psi (690 bar)
O-RING
10000
(690) SPRING
ENERGIZED PEEK SEATS
MP & NPT Connection
SEAL
SEAT GLAND
5000
(345)
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
15
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 2-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
16
Ball Valves: Subsea Series 02-0108SE 0318
1" 2 Way Subsea Ball Valve Dimensions:
4.00
(101.6)
Ø3/8 - 16 TAP
2.00 (9.5)
(50.8) 0.625 Deep
(4) Places
A A
3.38
(85.7)
1.69
(42.9)
2.25 Hex
Ø 2.88
(73.0) 2.59
Locking Piece (65.9)
1.000±0.005 Square
(25.40±0.12)
11
19
9
1.75
(44.5)
12 Square Length
2.91
(73.81)
22 Ø 1.25 4.16
(105.5)
20
(31.7)
15 See Optional
16
Connections
5.80
(147.2)
7 13
8
2
21 5
6 5.19
(131.8) 4
3 11.70
(297.1)
10
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 11,150 FT (3400 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,000 psi (345 bar) is ordered.
17
Ball Valves: Subsea Series 02-0108SE 0318
3 Way Subsea Series: 3/16" (4.77mm) Orifice
Pressures to 20,000 psi (1379 bar)
NPT Connections
LOCKNUT
SEAT GLAND
10000
(690)
5000
(345)
O-RING
O-RING O-RING
0 100 200 300 400 500
(-18) (38) (93) (150) (204) (260) SEAT
BOTTOM BEARING
SEAT RETAINER
Temperature ºF (ºC)
BOTTOM GLAND
3 Way 3/16" Bore Subsea Ball Valve
Pressure Ratings are determined by the end connections chosen, see chart.
Maximum Temperature rating is determined by the o-ring or PEEK seat material To ensure proper fit use Parker Autoclave tubing
Note: Side inlet pressure not recommended. Bottom inlet pressure only.
PAE Ball Valves are designed to be used in fully open or fully closed position.
NPT connections are limited to 400°F max due to PTFE Sealant.
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
See ball valve actuator section for full description, additional information, and options.additional information, and options.
18
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 3-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
19
Ball Valves: Subsea Series 02-0108SE 0318
3/16" 3 Way Subsea Ball Valve Dimensions:
1.00
THK
BODY
(25.4)
0.50
(12.7)
0.216 ± .001
(5.49 ± .025)
.249 ± .001
12
(6.32 ± .025)
1.28 2.00
(50.8)
15
(32.5)
0.94
6
(23.87) 1.00
16 Ø 0.28 TYP
(7.11)
(25.4)
3 .041 TYP
(10.41)
4.34
(110.23) 1.19 HEX TYP
(30.22)
1.50
(38.1) 5
17 13
2.56
(65.02)
8 1
SEE END
CONNECTION
9
OPTONS
(3 PLACES)
11 4
10
7
14
1.00 HEX TYP
2
(25.4)
2.50
(63.50)
4.72
(119.89)
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 10,300 FT (3140 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 4,500 psi (310 bar) is ordered.
20
Ball Valves: Subsea Series 02-0108SE 0318
3 Way Subsea Series: 3/8" (8.33mm) Orifice
Pressures to 10,000 psi (690 bar)
BELLEVILLE WASHERS
10000 THRUST WASHER
(690) MP & NPT Connection BELLEVILLE BACKUP
STEM SEAL
SEAT
3 Way 3/8" Bore Subsea Ball Valve BOTTOM BEARING
SEAT RETAINER
Pressure Ratings are determined by the end connections chosen, see chart.
Maximum Temperature rating is determined by the o-ring or PEEK seat material
Note: Side inlet pressure not recommended. Bottom inlet pressure only. BOTTOM GLAND
PAE Ball Valves are designed to be used in fully open or fully closed position.
NPT connections are limited to 400°F max due to PTFE Sealant.
To ensure proper fit use Parker Autoclave tubing
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
Flow Configuration
3-Way 3-Way
Switching Diverting
180 Turn 90º Turn
See ball valve actuator section for full description, additional information, and options.additional information, and options.
21
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 3-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
When ordering a basic repair kit add an “R” prefix H Handle/Handle Stop
22
Ball Valves: Subsea Series 02-0108SE 0318
3/8" 3 Way Subsea Ball Valve Dimensions:
0.281 ± 0.001
12
2 FLATS 180º APART
(7.14 ± .025)
0.81
Flat Length
2.06
(52.3) 17
1 2.00
(50.8)
1.00
4
(25.4)
10
0.41 TYP
(10.4)
Ø 0.28 HOLE
(2) PLACES (7.1) 7
5
1.63
(41.4)
6
8
3.03
(77.0)
18
3
9
13 2
14
16
15
11
3.00
(76.2)
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 11,500 FT (3505 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,000 psi (345 bar) is ordered.
23
Ball Valves: Subsea Series 02-0108SE 0318
3 Way Subsea Series: 1/2" (12.7mm) Orifice
Pressures to 10,000 psi (690 bar)
PACKING GLAND
10000
(690) MP & NPT Connection
5000
(345)
O-RING
NOTE: Critical gas applications such as Hydrogen or Helium should be evaluated on a case by case basis. Consult factory.
Ball Valves are designed to be operated in fully open or fully closed position
Flow Configuration
3-Way 3-Way
Switching Diverting
180 Turn 90º Turn
See ball valve actuator section for full description, additional information, and options.additional information, and options.
24
Ball Valves: Subsea Series 02-0108SE 0318
Ordering Guide:
For complete information on available end connections, see previous page. 3-way ball valves are furnished complete
with tube or pipe connections. Standard valve has Buna-N o-rings [250°F (121°C) maximum].
2.00
(50.8)
1.00
(25.4)
0.69
(17.5)
1.38
(35.1)
0.281 ± 0.001
0.81
14
2 FLATS 180º APART
FLAT LENGTH (7.14 ± .025)
(20.6)
15
2.06
(52.3)
Ø 0.437 ± 0.001
(11.1 ± .025)
4
1 2.00
(50.8)
1.00
(25.4)
8
Ø 0.28 HOLE
(2) PLACES
(7.1)
5 0.41 TYP
(10.4)
7
1.63
9
(41.4)
6 18
3.03
(77.0)
10
12 SEE END
CONNECTION
OPTIONS
(3 PLACES)
2
1.75” HEX
SEE SEAT
3
(44.5)
GLAND HEX
13 1.28
16
(32.5)
11
17
3.00
(76.2)
NOTE: NOTE:
1. MAWP (See Table) Valve Stem has no stop supplied as standard.
2. Maximum Sea Depth 11,500 FT (3505 meters) Stem will rotate 360° unless used with Subsea Actuator or Handle/Stop
3. Maximum External Pressure 5,000 psi (345 bar) is ordered.
26
Ball Valves: Subsea Series 02-0108SE 0318
Parker’s Motion & Control Technologies
At Parker, we’re guided by a relentless drive to help our customers become more productive and achieve higher levels of profitability by engineering
the best systems for their requirements. It means looking at customer applications from many angles to find new ways to create value. Whatever
the motion and control technology need, Parker has the experience, breadth of product and global reach to consistently deliver. No company knows
more about motion and control technology than Parker. For further information call 1-800-C-Parker.
Aircraft Engines Commercial Business and General Aviation Flight Control Systems & Components Hydraulic Systems & Components
Commerical Transports Land-Based Weapons Systems Fluid Conveyance Systems Inert Nitrogen Generating Systems
Military Aircraft Missiles and Launch Vehicles Fluid Metering Delivery & Atomization Pneumatic Systems & Components
AEROSPACE
Regional Transports Unmanned Aerial Vehicles Devices Wheels & Brakes
Fuel Systems & Components
Aerospace Industrial Machinery Brass Fittings & Valves PTFE & PFA Hose, Tubing & Plastic Fittings
Agriculture Mobile Diagnostic Equipment Rubber & Thermoplastic Hose & Couplings
FLUID and Bulk Chemical Handling Oil & Gas Fluid Conveyance Systems Tube Fittings & Adapters
GAS HANDLING Construction Machinery Transportation Industrial Hose Quick Disconnects
Food & Beverage Welding
Fuel & Gas Delivery
Aerospace Industrial Machinery Diagnostic Equipment Power Take-Offs
Aerial lift Mining Hydraulic Cylinders & Accumulators Rubber & Thermoplastic Hose & Couplings
Agriculture Oil & Gas Hydraulic Motors & Pumps Tube Fittings & Adapters
HYDRAULICS
Construction Machinery Power Generation & Energy Hydraulic Systems Quick Disconnects
Hydraulic Valves & Controls
Forestry Truck Hydraulics
27
Ball Valves: Subsea Series 02-0108SE 0318
Parker Worldwide
North America Asia Pacific Europe, Middle East, Africa
USA – Corporate, Cleveland, OH AU – Australia, Dandenong AE – UAE, Dubai ES – Spain, Madrid PT – Portugal, Leca da Palmeira
Tel: +1 256 896 3000 Tel: +61 (0)2 9842 5150 Tel: +971 4 812 7100 Tel: +34 902 33 00 01 Tel: +351 22 999 7360
customer.service.au@parker.com parker.me@parker.com parker.spain@parker.com parker.portugal@parker.com
USA – IPD, Huntsville, AL
Tel: +1 256 881 2040 CN – China, Shanghai AT – Austria, Wiener Neustadt FI – Finland, Vantaa RO – Romania, Bucharest
ipdcct@parker.com Tel: +86 21 2899 5000 Tel: +43 (0)2622 23501-0 Tel: +358 (0)20 753 2500 Tel: +40 21 252 1382
INGtechnical.china@parker.com parker.austria@parker.com parker.finland@parker.com parker.romania@parker.com
USA – IPD, (Autoclave), Erie, PA
Tel: +1 814 860 5700 HK – Hong Kong AT – Eastern Europe, Wiener Neustadt FR – France, Contamine s/Arve RU – Russia, Moscow
ipdaecct@parker.com Tel: +852 2428 8008 Tel: +43 (0)2622 23501 900 Tel: +33 (0)4 50 25 80 25 Tel: +7 495 645-2156
parker.easteurope@parker.com parker.france@parker.com parker.russia@parker.com
CA – Canada, Grimsby, Ontario IN – India, Mumbai
Tel +1 905-945-2274 Tel: +91 22 6513 7081-85 AZ – Azerbaijan, Baku GR – Greece, Athens SE – Sweden, Spånga
ipd_canada@parker.com Tel: +994 50 2233 458 Tel: +30 210 933 6450 Tel: +46 (0)8 59 79 50 00
ID – Indonesia, Tangerang parker.azerbaijan@parker.com parker.greece@parker.com parker.sweden@parker.com
Tel: +62 2977 7900
parker.id@parker.com BE/LU – Belgium, Nivelles HU – Hungary, Budapest SK – Slovakia, Banská Bystrica
South America Tel: +32 (0)67 280 900 Tel: +36 223 885 470 Tel: +421 484 162 252
AR – Argentina, Buenos Aires JP – Japan, Tokyo parker.belgium@parker.com parker.hungary@parker.com parker.slovakia@parker.com
Tel: +54 3327 44 4129 Tel: +(81) 3 6365 4020
falecom@parker.com infophj@parker.com BG – Bulgaria, Sofia IE – Ireland, Dublin SL – Slovenia, Novo Mesto
Tel: +359 2 980 1344 Tel: +353 (0)1 466 6370 Tel: +386 7 337 6650
BR – Brazil, Diadema, SP KR – South Korea, Seoul parker.bulgaria@parker.com parker.ireland@parker.com parker.slovenia@parker.com
Diadema, SP Tel: +82 2 559 0400
Tel: +55 11 4360 6700 parkerkr@parker.com BY – Belarus, Minsk IT – Italy, Corsico (Ml) TR – Turkey, Istanbul
falecom@parker.com Tel: +48 (0)22 573 24 00 Tel: +39 02 45 19 21 Tel: +90 216 4997081
MY – Malaysia, Selangor parker.belarus@parker.com parker.italy@parker.com parker.turkey@parker.com
CL – Chile, Santiago Tel: +603 784 90 800
Tel: +56 (0) 2 2303 9640 parkermy@parker.com CH – Switzerland, Etoy KZ – Kazakhstan, Almaty UA – Ukraine, Kiev
falecom@parker.com Tel: +41 (0) 21 821 87 00 Tel: +7 7273 561 000 Tel: +48 (0)22 573 24 00
SG – Singapore, parker.switzerland@parker.com parker.easteurope@parker.com parker.ukraine@parker.com
MX – Mexico, Toluca Tel: +65 6887 6300
Tel: +52 722 275 4200 parkersg@parker.com CZ – Czech Republic, Klecany NL – The Netherlands, Oldenzaal UK – United Kingdom, Warwick
contacto@parker.com Tel: +420 284 083 111 Tel: +31 (0)541 585 000 Tel: +44 (0)1926 317 878
TH – Thailand, Bangkok parker.czechrepublic@parker.com parker.nl@parker.com parker.uk@parker.com
Tel: +66 2 186 7000
phthailand@parker.com DE – Germany, Kaarst NO – Norway, Stavanger ZA – South Africa, Kempton Park
Tel: +49 (0)2131 4016 0 Tel: +47 66 75 34 00 Tel: +27 (0)11 961 0700
TW – Taiwan, Taipei parker.germany@parker.com parker.norway@parker.com parker.southafrica@parker.com
Tel: +886 2 2298 8987
enquiry.taiwan@parker.com DK – Denmark, Ballerup PL – Poland, Warsaw
Tel: +45 43 56 04 00 Tel: +48 (0)22 573 24 00
VN – Vietnam, Hochi Minh City parker.denmark@parker.com parker.poland@parker.com
Tel: +848 382 508 56
parker_viet@parker.com
! CAUTION !
Do not mix or interchange component parts or tubing with those of other manufacturers. Doing so is unsafe and will void warranty.
Parker Autoclave Engineers Valves, Fittings, and Tools are not designed to interface with common commercial instrument tubing and are designed to only connect with tubing manufactured to
Parker Autoclave Engineers AES specifications. Failure to do so is unsafe and will void warranty.
WARNING
FAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH,
PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important
that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems,
the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The prod-
ucts described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.
Offer of Sale
The items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered by Parker will be
governed by the provisions stated in Parker's standard terms and conditions of sale (copy available upon request).
©2018 Parker Hannifin Corporation | Autoclave Engineers is a registered trademark of the Parker Hannifin Corporation Literature #: 02-0108SE March 2018
Instrumentation Products Division Instrumentation Products Division Parker Hannifin Manufacturing Ltd.
Autoclave Engineers Operation Division Headquarters Instrumentation Products Division,
8325 Hessinger Drive 1005 A Cleaner Way Europe
Erie, PA 16509-4679 Huntsville, AL 35805 USA Riverside Road
Tel: 814 860 5700 Tel: 256 881 2040 Pottington Business Park
Fax: 814 860 5811 Fax: 256 881 5072 Barnstaple, UK, EX31 1NP, UK
www.autoclave.com Tel: 44 1271 313131
www.parker.com/ipd Fax: 44 1271 373636