Professional Documents
Culture Documents
Part4 Communal Aerial System CAC-953
Part4 Communal Aerial System CAC-953
, Ltd
2. Components
2.1 Connection Diagram of the System
(QAS-ADD-008/0/05.10.24) ( MRC G
MARINE RADIO CO., LTD.)
ٻ
.MARINERADIOCO.,LTD. Subject : Communal Aerial System Page : (3 / 8)
渂/昦愛怺昦 Date : 2010.8.09 Job : M50309
G
2.2 Components
1) Main amplifier(CAC-953) : The number of the maximum subscriber is 64 EA. Automatic gain amplifier
and power supplier for MF/SW/FM/VHF/UHF.
2) Sub amplifier(CAC-953A) : The number of the maximum subscriber is 128 EA. Automatic gain
amplifier and power supplier for MF/SW/FM/VHF/UHF.(Used when the number of the subscriber
exceeds 64 EA or cable is extremely damaged.)
3) VTR Amplifier(UP-40A, Option)
4) Omni-Directional Antenna(AT-807) : For FM, VHF/L, VHF/H, UHF
5) Six-meter whip antenna(AW-624) : For AM Radio
6) Antenna junction box(JB-4 W/T) : For AM Antenna
7) Distributor
8) Terminal for radio and TV
9) Radio/TV, telephone and AC-220 RP terminal
10) Radio/TV cord set
11) Installation materials: End Resister(75 Ohms and connector)
12) Spare parts : Manufacturer standard
3. Specification
3.1 MF/SW/FM/VHF/UHF Amplifier Unit (CAC-953, CAC-953A)
-1. Frequency Gain : MF/SW(150kHz - 30MHz) - Min. 20dB
: VHF.L(45MHz - 110MHz) - Min. 20dB
: VHF.H(170MHz - 225MHz) - Min. 20dB
: UHF(470MHz - 850MHz) - Min. 20dB
-2. Automatic Gain Control : 0 - 37dB
-3. Gain Deviation : MF/SW(0.8dB), VHF(1.0dB), UHF(2.0dB)
-4. Noise Figure : MF/SW(7dB), VHF(8dB), UHF(8dB)
-5. Maximum Output Level : MF/SW(85dB), FM/VHF/UHF(110dB)
-6. Power Consumption : DC-12V, 380mA, Max. 10VA
: AC-220V, 20mA, Max. 10VA
-7. Weight : Approx. 6.8Kg
-8. Operation Temperature : -20oC ૫ +40oC
-9. In/Out Impedance : 75 ohm
(QAS-ADD-008/0/05.10.24) ( MRC G
MARINE RADIO CO., LTD.)
ٻ
.MARINERADIOCO.,LTD. Subject : Communal Aerial System Page : (4 / 8)
渂/昦愛怺昦 Date : 2010.8.09 Job : M50309
G
3.4 6m Whip Antenna(AW-624)
-1. Frequency Range : 0.1MHz ૫ 30MHz
-2. Output Impedance : 75 ohm
-3. Rx Pattern & Polarization : Omni-Directional Type
-4. Height : 6.15m
-5. Operation Temperature : -40oC ૫ +50oC
-6. Stand Rate for Wind : Max. 50m/s
-7. Weight : Approx 2.7Kg
4. Installations
4.1 Installation Method
The performance of this system depends on the installation method. To install this system,
make sure that you consider the following;
ཛ Install an antenna in a high position to keep away from the metal obstacles.
ཛྷ Install an amplifier in place where humidity, heat or strong noise do not exist.
ཝ When you connect coaxial cable, you should not bend it extremely. If you bend it unavoidably,
it should be bent more 6 times than a diameter of coaxial cable.
ཞ Connect the external shield wires exactly.
ཟ When you connect coaxial cable to each connector, shorten the length of the insulated conductor
as possible.
འ When coaxial cable is damaged or cut, you should not connect it at random and should use the
standard connector.
ཡ Connect 75 Ohm of noninductive resistance to each port that is not used.
ར Shorten the length of cable as possible.
ལ To install each terminal, keep the maximum radius from noise source because its field intensity
is low.
ཤ Make sure of using the standard coaxial cable.
ཥ If the length of cable is too long or the number of the distribution exceeds the standard limit,
make sure of using the sub amplifier.(For more information, inquire of the manufacturer)
(QAS-ADD-008/0/05.10.24) ( MRC G
MARINE RADIO CO., LTD.)
ٻ
.MARINERADIOCO.,LTD. Subject : Communal Aerial System Page : (5 / 8)
渂/昦愛怺昦 Date : 2010.8.09 Job : M50309
G
4.2 Connection Method of Antenna Connector & Coaxial Cable(RG-12U)
(QAS-ADD-008/0/05.10.24) ( MRC G
MARINE RADIO CO., LTD.)
ٻ
.MARINERADIOCO.,LTD. Subject : Communal Aerial System Page : (6 / 8)
渂/昦愛怺昦 Date : 2010.8.09 Job : M50309
G
4.4 Connection Method of U-P-G Connector & 5C-FB Cable
ཛ Remove 5C-FB cable as shown in figure. Keep the gap of 4mm and 10mm.
The inner center should not be cut.
ཛྷ Fully remove the gold-colored shield to the position c.
ཝ Do not remove the silver foil at the position d.
ཞ First, insert the support ring to cable and then U-P-G connector to PVC. At this time,
insert the insulator to the position e.
ཟ Place the support ring to the position e and tighten it with a nipper as shown in figure.
5. General Cautions
ཛ If the vessel is in port, the duel image can be displayed due to the reflected wave from building,
crane and mountain. This originates from the omni-directional antenna.
ཛྷ If this antenna is too near the transmitting antenna of the certain broadcasting station,
the transmission of other broadcasting stations can be extremely degraded. This originates from
the self-AGC operation of the amplifier that prevents the saturation generated by the
strong signal of the certain broadcasting station.
ཝ Because the short wave has various problems(For example, fading, diffuse reflection, attenuation
and atmospherics), the receiving strength can extremely vary.
ཞ Make sure that you do not change the circuit and components in this system at your own.
ཟ Connect cable exactly, according to the terminal symbol of the drawing.
འ Connect the ground lines in each port to that in cable.
ཡ The reflected wave of the AM wave between transmitting stations is too near compared to that
of TV wave. So, it can be confused with other wave when it is amplified to high gain.
ར When the power lamp indicating the ground failure is on, use the recommended insulation cord
to connect TV.
ལ Adjust the main/sub amplifier of the omni-directional antenna automatically.
ཤ Connect the coaxial cable of the out-let box firmly.
ཥ Carefully connect cable. If a problem occurs in cable, troubleshooting is impossible in fact.
That is why too much time and cost are required to resolve the problems.(Ask manufacturer).
(QAS-ADD-008/0/05.10.24) ( MRC G
MARINE RADIO CO., LTD.)
ٻ
.MARINERADIOCO.,LTD. Subject : Communal Aerial System Page : (7 / 8)
渂/昦愛怺昦 Date : 2010.8.09 Job : M50309
G
6. Maintenance and Trouble Shooting
-3. Distributer
- After installing a terminal resistor(75ಳ) on outlet box and distributer.
ཛInput/output DC impedance of 4-way Distributer : App. 20ಳ
ཛྷ Input/output DC impedance of 2-way Distributer : App. 40ಳ
- Before installing a terminal resistor(75ಳ) on outlet box and distributer.
ཛ Input/output DC impedance of 4-way Distributer : more 10
ཛྷ Input/output DC impedance of 2-way Distributer : more 10
(QAS-ADD-008/0/05.10.24) ( MRC G
MARINE RADIO CO., LTD.)
ٻ
SKH-10
05(New Model)
Our new mo odel SKH‐105 5 outlet with
h F connectorr outputs forr Radio and TV
T double isoolated to pre
event ground d
loop interfeerence. It alsso covers all Radio‐TV freequencies frrom 0.1 to 890
8 MHz. It is also desiggned to takee
advantage o of the extremely good efficciency of the Tap‐Off meth hod of "Home Run" signall distribution.
This outlet iss flush moun nt with a 76x7 76mm face p late in the staandard config guration. It caan be made tto be surfacee
mounted byy using the optional
o N frame that iss about 1" deep
d and 76xx76mm. TV CCords with F F fittings aree
available. Raadio Cords wiith AM‐FM impedance m matching Splitters are also o available.
SPEC
CIFICATIIONS
Frequeency Range (M
MHz): TV
V: 47‐68; 1330‐890
R: 0.1‐30; 888‐108
Througgh Loss (dB): In TV 47‐68MH Hz: 1dB nom. to 2.8dB
B max.
In TV 130‐890MMHz: 1dB nom. to 1.5dB B max.
In R 0.1‐30; MH
Hz: 2.5dB
B nom. to 4dB
B max.
In R 88‐108MH Hz: 1dB nom. to 1.8dB
B max.
Isolatio
on: TV
V‐R: 12dB min.
Return
n Loss: In 5‐890MH
Hz 8dB m
min.
V 47‐68MHzz 8dB m
TV min.
130‐890M
MHz 8dB m min.
R 88‐108MHHz 8dB m
min.
Connectors: Input: Term inal Block
TV:
T "F" orr IEC Male
R:
R "F" orr IEC Female
Impedance: 75
5 Ohms
Galvan
nic isolation: 40
00V
Op
ptional 2.5kV
V with reduce
ed frequency range only w
with special orrder
Screen
ning factor: TVV: 35dB
R:
R 43dB
Operatting Temp. (C
C): ‐40~+60
Cutoutt Dimensionss: 50
0x50x36mm(H
HxWxD)