Professional Documents
Culture Documents
KO-BA081010 Manual
KO-BA081010 Manual
●Thank you for purchasing our product. Before installing/operating the product, read the instructions carefully and retain them
for future reference.
Attention!
● For installation, follow the steps described. Any damage caused by wrong installation shall be imputed to the users.
● To avoid a short circuit from occuring do not pull or modify the wires during installation.
● Do not disassemble or change any parts. Opening and dissassembling this unit will void any warranty.
● Maintenance and repairs should be executed by our professionals only.
FLASH LIGHT ON
◎ Symbol description:
NOTE
Some procedures must be followed to avoid damages to the instrument. PRESS THE HOLD THE
BUTTON FOR BUTTON 3
WARNING! Certain procedure must be followed to avoid damages to yourself, to the vehicle to others. ONE SECOND SECONDS
1-1 Accessories
1 LCD Meter X1 2 Main wiring harness X1 3 Active speed sensor X1 4 RPM wire (Type A) X1
5 RPM wire set(TYPE B) X1 6 Sensor wire set X2 7 Temperature sensor X2 8 M8 / S type speed
sensor bracket X 1
21 M8 Bushing X2
wh081ba02a(P22-1)
1-2 Optinal accessories
1 L type speed sensor
bracket 2 Oil temp sensor adapter 3 Water temp sensor
adapter 4 Signal wire
M12 X P1.5 X 15L
M14 X P1.25 X 15L
M14 X P1.5 X 15L
M16 X P1.5 X 15L
M18 X P1.5 X 15L M14
M20 X P1.0 X 15L M16. M18
BI003S01 M20 X P1.5 X 15L BG****** M22. M26 mm BG0***** 20-c94300a
NOTE Some of the option accessories may be purchased separately. For more details, contact your local distributor.
A
RPM wire (Type A)
(Accessory 4)
The color listed above may differ depending
RPM wire set(TYPE B) on the model.
(Accessory 5)
Ignition coil positive
Coil Spark plug wire The fuel sensor is electronic type, don't
Flywheel connect in parallel with the original- otherwise
C B Spark plug cap the fuel gauge won't display. Wrong
RPM wire set(TYPE B) installation of the fuel wiring may cause
Ignition (Accessory 5) damages to the meter.
pulse
Tachometer Pick up
Spark
NOTE When connecting the power wire, follow the instructions carefully. If the red & brown wires are connected in parallel, the
meter won 't work properly.
The RPM wire installation
We recommend installing the R type spark plug or low-resistance spark plug cap at the same time.
A. Connect the RPM wire (Type A) on the spark plug wire by connecting the male and female connectors.
B. Connect the RPM wire (Type B) to the pick up sensor.
C. Connect in parallel the RPM wire (Type A) with the original tachometer signal wire.
The best signal source will be in order as C>B>A, we will suggest that you check different ways if you have problems
getting the RPM signal.
wh081ba02a(P22-2)
2-2 Installation instructions
1. Follow the steps below during installation.
2. 1. 1. M6 or M8 Bolt X2 (Accessory 16,17)
2. 2. M6 or M8 Spacer X2 (Accessory 18,19)
3. Meter bracket (Accessory 13)
7. 4. M6 or M8 Bushing X2 (Accessory 20,21)
3. 5. Handlebar bracket
NOTE You can also install it (meter bracket) on the original
6. 0.9 Nm (9 kgf.cm) meter bracket.
7.
6. M5 screw X 3 (Accessory 14)
7. M5 washer X3 (Accessory15)
8. 4. 7.
8. LCD Meter (Accessory1)
9. 9. Meter bracket micro-adjustment screw
4. 0.45 Nm (4.5 kgf.cm) NOTE You can choose the angle first and then use the screw
5. to fix the angle.
NOTE The handle bar bracket screw and screw hole will differ
depending on the model. We suggest you to use
the additional assembly (item 1.2.4) to fit it.
mile
1. Drill a 22.5mm hole in the 2. Weld the sensor bung 3.Install the oxygen sensor After removing the oxygen sensor(Option accessory 5)
exhaust system at 200 mm (Option accessory 6) to (Option accessory 5) into ,remember to put the bung cap(Option
away from the exhaust flange. the exhaust system. the bung. accessory7) back to place.
CAUTION! Make sure the sensor doesn't hit the body or engine when installing to avoid accidents or damaging the sensor.
Ad just t he senso r b racket p o sit io n t o m ake Adjust the distance between sensor and
sure t hat t he senso r faces t he m ag net t o magnet. We suggest you make sure the
p revent b ad sp eed sig nal o r no sig nal! distance is under 1 mm for an optimal
speed signal.
below speed
1 mm sensor
Use the zip tie to fix the bracket on Adjusting the distance between the sensor
the front fork. Make sure the disc and screw to get the best speed signal.
screw could pass the hole on the bracket for Make sure the distance is under 2mm
you to install the sensor into the same hole for to get the best signal.
catching the speed signal.
wh081ba02a(P22-3)
The active speed sensor needs to be facing a metal surface to detect the speed.
EX. 1 The disc screw.
EX. 2 The disc to detect the disc gap. (Make sure the distances between the gaps are the same in advance to avoid improper
speed signal.)
EX. 3 The sprocket to detect the disc gap. (Make sure the distances between the gaps are the same in advance to avoid improper
speed signal.)
EX. 4 Rear disc - detect the gap between the disc.
We suggest you obtain the speed from the disc screws. The more sensor points are, the better the speed accuracy is. The
maximum sensor points the speed sensor could detect is 40 points per turn.
After installation, use your hand to turn the tire to see if everything is ok. The LED on the active speed sensor will light up
once the signal is detected.
EX. 1
The hexagon socket disc screw The hexagon screw
The best detection area: The edge of The best detection area: The middle
speed
sensor the hexagon socket screw. of the screws.
speed speed speed
speed sensor Don't pick-up the signal from sensor sensor Some hexagon screw centers have a small
sensor the middle hole of the hexagon hole in this case,we suggest you to obtain
socket screw to avoid wrong signal. the signal from the edge of the screw like the
the detect range the detect range hexagon socket screw.
Gear Meter
Indicator ●Display range :
●ABS light (Amber) -, N, 1 ~ 6
4
●Left indicator light(Green) 4 5 6 7 8 9 10
●Check engine light (Amber) 3 Speedometer
3000 RPM
60
●Neutral light (Green) 00:00
GEAR
2
●Display range :
●Composite warning light (Red) 1
0 ~ 360 km/h (0 ~ 225 MPH)
●High beam light (Blue) 1
●Display unit :
●Right indicatior light(Green) 0 1/2
x1000RPM 1 km/h (MPH)Switchable
●Motor oil maintenance light (Red) km/h
105.2 °C 67.9 °C
0
12.5 v ODO 21528 km Trip A 729.5 km
Select Adjust
wh081ba02a(P22-4)
3-3 Specifications(Meter)
●Speedometer Display range : 0 ~ 360 km/h (0 ~ 225 MPH) ○High voltage Setting range : DC 13.1~18.0 V, when setting
Display unit : 1 km/h (MPH) Switchable warning value is above, the color of the number turns to
○Odometer Display range : 0 ~ 999,999 km (mile)and then red and flashes.
return to zero Setting unit : DC 0.1 V
Display unit : 1 km (mile) ●Target speed Setting range : 30 ~ 360 km/h (20 ~ 225 MPH)
○Trip meter A, B Display range : 0.0~9,999.9 km (mile), may return Setting unit : 5 km/h (MPH)
to zero manually ●Target distance Setting range : 50 ~ 1,500 m (1/32 ~ 30/32 mile)
Setting unit : 0.1 km (mile) Setting unit : 50 m (1/32 mile)
○Motor oil maintenance Setting range : 500 ~ 16,000 km(300~10,000 ●Top speed Display range
mile),OFF Speed : 0 ~ 360 km/h (0 ~ 225 MPH)
Setting unit : 100 km(mile) Distance : 0 ~ 999 m (0~3,280 feet)
○Speeding warning Setting range : 30~360 km/h (20~225 MPH), Rotating speed : 0 ~ 10,000 RPM / 0 ~ 12,500 RPM、
setting when setting value is reach or above, warning 0~15,000 RPM / 0 ~ 18,000 RPM
light will illuminate. Time : 0 ~ 9 : 59”99
Setting unit : 1 km/h (MPH) ●Record order Setting range : Sequence, Best.
○Max. speed record Display range : 0 ~ 360 km/h (0 ~ 225 MPH) ●Bluetooth® Operating system
Display unit : 1 km/h (MPH) connection status iOS : iOS 5.0 and above
○Circumference Setting range : 300~2,500 mm Android : Android 9 and above
Setting unit : 1 mm ●Phone battery Display range: 3 segments
○Sensitive point Setting range : 1~20 P ●Incoming phone Display range: Display name or number for up to
Setting unit : 1 P call notice 12 letters; “…” is displayed for more than
●Gear Meter Display range : -, N, 1~the highest gear, 12 letters; “Unknown” is displayed when there is no name
(the highest gear shall be based on the gear learning) iOS - Display either name or number of the incoming call
○Max. Gear record Display range : -, N, 1~the highest gear Android - Display number only
(the highest gear shall be based on the gear learning) ●Incoming online Display range: Display name for up to 12 letters; “…”
, may return to zero manually. app call notice is displayed for more than 12 letters;
●Tachometer Display range : 0~10,000 RPM / 0~12,500 RPM / “Unknown” is displayed when there is no name
0~15,000 RPM / 0~18,000 RPM App supported: LINE, WeChat, WhatsApp
○Pre-shift light warning Setting range : iOS supported, Android not supported.
setting 1,000~10,000 RPM / 1,000~12,500 RPM / ●Music playing Song name:15 letters, and “…” is displayed
1,000~15,000 RPM / 1,000~18,000 RPM message when > 15 letters
Setting unit : 100 RPM Artist name:18 letters, and “…” is displayed
○Shift light warning Setting range : when > 18 letters
setting 1,000~10,000 RPM / 1,000~12,500 RPM / Total length of the music:00:00 ~ 9:59:59
1,000~15,000 RPM / 1,000~18,000 RPM (iOS supported, Android not supported).
Setting unit : 100 RPM Current playing time : 00:00 ~ 9:59:59
○Max. rotating speed Setting range : (iOS supported, Android not supported).
0~10,000 RPM / 0~12,500 RPM / ●Push notification Display range:
0~15,000 RPM / 0~18,000 RPM ,may return Name - 4 letters, “…” is displayed when > 4 letters
to zero manually Content -17 letters, “…” is displayed when > 17 letters
○The RPM input signal Setting range : 0.5,1.0~24.0 Support iOS, not Android.
number setting ●Background display Setting range : Auto(automatically switch
○The RPM input pulse Setting range : Low-Act, High-Act according to the light : day mode display for a
●Thermometer A, B Display range : 0.0 ~ 250.0 ˚C (32.0 ~ 482.0 ˚F) bright environment and Night mode display for
Display unit : 0.1 °C (°F) a dark environment), Day mode, Night mode.
○Overheat warning Setting range : 60 ~ 250 °C (140 ~ 482 °F), ○Back light brightness Setting range : 1/5(Darkest)~ 5/5(Brightest)
A, B setting when setting value is reached , the color of the (Day) Setting unit : 1/5
number turns to red and flashes. ○Back light brightness Setting range : 1/5(Darkest) ~ 5/5(Brightest),need
Setting unit : 1 °C (°F) (Night) ≦ the setting value of backlight brightness (day).
○Max. temperature A, B Display range : 0.0 ~ 250.0 ˚C (32.0 ~ 482.0 ˚F) Setting unit : 1/5
record , may return to zero manually ○Back light color Setting range : blue, green, orange, white
Display unit : 0.1 °C (°F) ●Unit Speed unit : km/h , MPH
●A/F ratio meter Display range : 12.1~17.5 Temperature unit : ˚C (Celsius) and ˚F (Fahrenheit)
Display unit : 0.1 ●Voltage DC 12 V
●Fuel meter Display range : 6 levels (0~100%) ●Operating temperature -20~ 85 °C
Display unit : 1 level(16.6 %) ○Storage temperature -30~ 90 °C
○Fuel Gauge Resistance Setting range : 100 Ω, 250 Ω, 270 Ω,390 Ω, ●Specification JIS D 0203 (S2)
(Ω) 510 Ω, 1200 Ω, SW, learning mode,OFF ●Meter Size 170 x 86.2 x 42.5 mm
○Fuel warning setting Setting range : 0 ~ 3/6, when setting value is ●Meter Weight Around 246.0 g
reached or below, warning light will illuminate. ●Indicator ABS light (Amber)
Setting unit : 1 Left indicator light(Green)
●Clock Setting range : 00:00~23:59 (24H) Check engine light (Amber)
01:00~12:59 (12H) Neutral light (Green)
○Perpetual calendar Display range (year):2021 ~ 2099 Composite warning light (Red)
Display range(month):1 ~ 12 High beam light (Blue)
Display range(day):1 ~ 31 Right indicatior light(Green)
Display range(Week) : MON, TUE, WED, THU, Motor oil maintenance light (Red)
FRI, SAT, SUN
NOTE Design and specifications are subject to change without notice.
●Voltmeter Display range : DC 8.0 ~ 18.0 V
Display unit : DC 0.1 V
○Low voltage warning Setting range : DC 8.0~13.0 V, when setting
value is below, the color of the number turns to
red and flashes.
Setting unit : DC 0.1 V
wh081ba02a(P22-5)
4-1 Start screen for Initial Use
Hello! ●Start screen for Initial Use, press the 2021/ 01/ 21 FRI 00:00
●Vehicle condition screen.
Information Service
Select your mobile OS. Adjust or Select button to choose ●Press the Adjust + Select buttons,
12.5 21538 km
to enter the main screen.
ODO
mobile operating system.
V
iOS
Android 65.0 °C Trip A 729.5 km
Next
explanation in the graphics. 1 1/2 0 Service 500 km
4
5 6 7 8 9 10
Hello! ●Press the Adjust button for 3 seconds, 3
4
●The main screen.
enter the Bluetooth® pairing screen. 3000 RPM
60
00:00
GE A R
Select your mobile OS.
2 1
iOS ●EX : Select iOS for mobile phone 1
operating system
Android
0 1/2
x1000RPM
km/h
Next
NOTE iOS operating system: 105.2 °C 67.9 °C
Information Service
(Flash), press the Adjust button to enter
12.5 ODO 21538 km
the Vehicle condition screen.
V
60
00:00
Adjust button to go back to the Trip A
120
MAX RECORD
G EA R GE A R
2 1 2
screen.
1
●Press the Adjust button for 3 seconds 1
0
x1000RPM
km/h
1/2
120 0
MAX RECORD MAX RECORD
GEAR G E AR
2 2
1 1
0 0
x1000RPM x1000RPM
km/h km/h
4
10000 RPM 105.2 °C 67.9 °C 0 RPM 0.0 °C 0.0 °C
4 5 6 7 8 9 10
3
●In the Trip B screen, press the Adjust button
3000 to enter the Max. record screen.
60
00:00 RPM
4
G EA R
4 5 6 7 8 9 10
2 1
3
●In the Trip A sereen.
●Press the Adjust button for 3 seconds 3000 RPM
60
1 00:00
GEAR
0 1/2 2 1
x1000RPM
km/h to reset Trip B record. 1
105.2 °C 67.9 °C 0
3055.5 km 0 km
1/2
Trip B Trip B
0
12.5 v ODO 21528 km Trip B 3055.5 km x1000RPM
km/h
105.2 °C 67.9 °C
0
12.5 v ODO 21528 km Trip A 1688.9 km
wh081ba02a(P22-6)
4-4 Record Screen Switching Description(Target Speed, Target Distance, Top Speed)
4
4 5 6 7 8 9 10 Top Speed
●In the main screen, press the Select + ●In the top speed record screen, press the
(km/h,m)
No Time Speed RPM DST
3
3000 RPM
60
00:00
2
GEAR
1
Adjust buttons to enter the target speed 1
2
0:21.29
0:29.05
129
121
8600
12000
224
368
Select + Adjust buttons to go back to
1
record screen. 3 0:23.28 128 10200 324
GO!
the main screen.
4 0:26.09 122 9200 279
0 1/2
x1000RPM
0:20.07 136 9400 282
km/h 6 0:26.22 130 11500 347
105.2 °C 67.9 °C 7 0:29.02 132 10800 350
0
12.5 v 8 0:25.03 127 10100 325
ODO 21528 km Trip A 729.5 km
4
Target Speed
No Time Speed RPM
(km/h,m)
DST
●In the target speed record screen, press 3
4 5 6 7 8 9 10
●In the main screen.
the Select button to enter the target 3000 RPM
60
1 0:21.29 120 8600 224 00:00
GE A R
2 0:29.05 120 12000 368 2 1
3 0:23.28 120 10200 324
GO!
distance record screen. 1
4 0:26.09 120 9200 279
0 1/2
0:20.07 120 9400 282 x1000RPM
110
Target Speed: 0~180 km/h
1 0:21.29 120 8600 224
the Adjust button to enter the testing 2
GE A R
2
3
0:29.05
0:23.28
120
120
12000
10200
368
324 screen. stop (19"20 second).
GO! 1 M
NOTE Start the test when the bike is A
4 0:26.09 120 9200 279
0
0:20.07 120 9400 282 x1000RPM X
6 0:26.22 120 11500 347 fully stopped. km/h
7 0:29.02 120 10800 350
8 0:25.03 120 10100 325 0:19.20 105.2 °C 67.9 °C 525 m
N 6
5 6 7 8 9 10 4 5 6 7 8 9 10
3
4
●In the testing screen. 3
●When speed decreases to 0 km/h (MPH),
0
the target speed record screen will apear.
Target Speed: 0~180 km/h
0
Target Speed: 0~180 km/h
WARNING! Use this function on
GE AR GE A R
2 2
1
racetracks to avoid 1 M
0 accidents. 0 A
x1000RPM
km/h
x1000RPM
km/h X
2
5 6 7 8 9 10 Target Speed
3
4
●When the bike moves, the timer will No Time Speed RPM
(km/h,m)
DST
●In the target speed record screen.
start automatically.
25
Target Speed: 0~180 km/h 1 0:21.29 120 8600 224
GEAR
2 2 0:29.05 120 12000 368
●Press the Adjust button for 3 seconds,
1 NOTE The timer is automatic, so when 3
4
0:23.28
0:26.09
120
120
10200
9200
324
279
GO!
to reset the target speed record.
0
x1000RPM
your bike starts to move the timer 0:20.07 120 9400 282
km/h
will start to calculate the time and 6 0:26.22 120 11500 347
0:02.50 13 m
stop automatically when you stop 7
8
0:29.02
0:25.03
120
120
10800
10100
350
325
the bike.
4
Target Speed (km/h,m)
4 5 6 7 8 9 10
3
●Speed up. No
1
Time
0:21.29
Speed
120
RPM
8600
DST
224
35
Target Speed: 0~180 km/h 2 0:29.05 120 12000 368
GEAR
3 0:23.28 120 10200 324
2 GO! Delete Records?
4 0:26.09 120 9200 279
0:20.07 120 9400 282 No Reset
1
6 0:26.22 120 11500 347
0 7 0:29.02 120 10800 350
x1000RPM 8 0:25.03 120 10100 325
km/h
●Press the Adjust button ●Successfully deleted.
0:14.85 50 m to confirm deletion. ●The alert dialog will disappear
●Press the Select button after 3 seconds.
to cancel deletion.
wh081ba02a(P22-7)
4-4-2 Description Of Target Distance Test
6
Target Distance 5 6 7 8 9 10
No Time Speed RPM
(km/h,m)
DST
●In the target distance record screen, press 3
4
●When you reach the target distance
the Adjust button to enter the testing that you set (100 M . 2/32 mile), the
72
1 0:21.29 128 8600 1500 Target Distance : 100 m
GE A R
2
2
3
0:29.05
0:23.28
130
126
12000
10200
1500
1500 screen. timer will stop (12"27 second).
GO! 1 M
NOTE Start the test when the bike is fully
4 0:26.09 129 9200 1500
0 A
0:20.07 135 9400 1500 X
stopped.
x1000RPM
km/h
6 0:26.22 121 11500 1500
7 0:29.02 129 10800 1500
8 0:25.03 120 10100 1500 0:12.27 105.2 °C 67.9 °C 100 m
N 6
5 6 7 8 9 10 5 6 7 8 9 10
3
4
●In the testing screen. 3
4
●When speed decreases to 0 km/h (MPH),
the target distance record screen will
0 0
Target Distance : 50 m Target Distance: 100 m
2
GEAR
WARNING! Use this function on 2
GE A R
1
5 6 7 8 9 10
3
4
●When the bike moves, the timer will No
Target Distance
Time Speed RPM
(km/h,m)
DST
●In the target distance record screen.
25
start automatically.
Target Distance : 100 m
GEAR 1 0:21.29 128 8600 1500
2 2 0:29.05 130 12000 1500
●Press the Adjust button for 3 seconds,
11 NOTE The product adopts digital sensing; 3
4
0:23.28
0:26.09
126
129
10200
9200
1500
1500
GO! to reset the target distance record.
0
x1000RPM
when the vehicle starts, the timer will 0:20.07 135 9400 1500
km/h
immediately start measuring. Upon 6 0:26.22 121 11500 1500
0:02.50 13 m
achieving the target distance, the timer 7
8
0:29.02
0:25.03
129
120
10800
10100
1500
1500 m
will immediately stop measuring.
2
5 6 7 8 9 10
4
●Speed up.
Target Distance (km/h,m) Target Distance (km/h,m) Target Distance (km/h,m)
No Time Speed RPM DST No Time Speed RPM DST No Time Speed RPM DST
3 1 0:21.29 128 8600 1500 1 0:21.29 128 8600 1500
35
Target Distance : 100 m
GEAR 2 0:29.05 130 12000 1500 2 0:29.05 130 12000 1500
2 3 0:23.28 126 10200 1500
GO!
3 0:23.28 126
Delete Records? 10200 1500
GO! GO!
4 0:26.09 129 9200 1500 4 0:26.09 129 9200 1500
11 0:20.07 135 9400 1500 No
0:20.07 135Reset
9400 1500
6 0:26.22 121 11500 1500 6 0:26.22 121 11500 1500
0
x1000RPM
7 0:29.02 129 10800 1500 7 0:29.02 129 10800 1500
km/h 8 0:25.03 120 10100 1500 8 0:25.03 120 10100 1500
100
the Adjust button to enter the testing
Top Speed
1 0:21.29 129 8600 224 GE A R
2
2
3
0:29.05
0:23.28
121
128
12000
10200
368
324 screen. counting the distance (510 m),
M
and time (25"65 seconds).
GO! 1
4 0:26.09 122 9200 279
A
0:20.07 136 9400 282 NOTE Start the test when the bike is fully 0
x1000RPM
km/h X
6 0:26.22 130 11500 347 stopped.
7 0:29.02 132 10800 350
8 0:25.03 127 10100 325 0:25.65 105.2 °C 67.9 °C 510 m
m
N 6
5 6 7 8 9 10 5 6 7 8 9 10
3
4
●In the testing screen. 3
4
●When speed decreases to 0 km/h (MPH),
0 0
the top speed record screen will apear.
Top Speed Top Speed
2
GEAR
WARNING! Use this function on 2
GE A R
racetracks to avoid
1 1 M
0
accidents. 0 A
x1000RPM
km/h
x1000RPM
km/h X
30
Top Speed 1 0:21.29 129 8600 224
GEAR
2 0:29.05 121 12000 368
●Press the Adjust button for 3 seconds,
NOTE Display range(Top speed) : 3
4
0:23.28
0:26.09
128
122
10200
9200
324
279
GO!
to reset the top speed record.
Speed : 0 ~ 360 km/h (0 ~ 225 MPH) 0:20.07 136 9400 282
km/h
Distance : 0 ~ 999 m (0~3,280 feet) 6 0:26.22 130 11500 347
7 0:29.02 132 10800 350
0:10.27 100 m Rotating speed : 0 ~ 15,000 RPM 8 0:25.03 127 10100 325 m
Time : 0 ~ 9'59"99
NOTE The product adopts digital sensing;
when the vehicle starts, the odometer
Top Speed Top Speed Top Speed
and the timer will immediately start
(km/h,m) (km/h,m) (km/h,m)
No Time Speed RPM DST No Time Speed RPM DST No Time Speed RPM DST
To change the speed unit of the function 8 0:25.03 127 10100 325 8 0:25.03 127 10100 325 8 0:25.03 127 10100 325
2
4 5 6 7 8 9 10 to cancel deletion.
3
●Speed up.
72
Top Speed
GEAR
2
1
0
x1000RPM
km/h
0:18.10 210 m
wh081ba02a(P22-8)
5 Setting Screen Switching Description
●Press the Adjust + Select buttons for 3 seconds on the main screen, record screen, or vehicle condition screen to switch to the setting screen.
●Press the Select button or Adjust button to select
❶Date/Clock ❷Unit(Speed/Temperature) ❸Backlight(Mode/Brightness/Color) ❹Speeding warning ❺Shift light warning
❻Overheat warning ❼Voltage warning ❽Fuel warning ❾Motor oil maintenance ABS warning Warning light warning
Tire circumference/Sensing point Gear RPM(Pulse / Signal / Range) Fuel resistance
A/F ratio Power Test Internal and External ODO Meter information Bluetooth® and etc.
●Press the Adjust button for 3 seconds to enter the setting function screen.
●In the setting screen, press the Select button for 3 seconds to switch to the startup screen.
NOTE During setting, if any button is not pressed for 3 minutes, it will automatically return to the startup screen.
4000 RPM
4
60
❶Date/Clock ❷Unit(Speed/Temperature)
13:59 ECO
G EA R
1
Time
00:00
Brightness (Night)
Shift Light is more than or equal
to Pre-Shift Light.
High Set
15.0 V 00500 km
Warning light warning Tire circumference/Sensing point Gear RPM(Pulse / Signal / Range)
Warning Light Speedometer Gear RPM
Overspeed Tire Circumference Function Pulse
OFF 1000 mm ON 1
Pre-Shift Light Sensor Point Learn Signal
Flash 01 P Start High-Act
Shift Light Learn Range
Steady Start 10000 RPM
Fuel resistance A/F ratio Power Test Internal and External ODO
Fuel A/F Ratio Power Test ODO
Type Function Target Speed Total
100 Ω OFF 050 km/h km
Target Distance Set
0050 m 000000 km
Sort by
If turn on AFR function, Temp B
will turn off. Sequence
wh081ba02a(P22-9)
5-1 Date & Clock Setting
Date & Clock ●The Date Clock
& Clock screen, press the Date & Clock ●Example : To set clock(hour) to 10 hours.
Date Adjust button for 3 seconds to enter Date ●Press the Select button to choose the
2021/01/01 FRI
the Date & Clock setting. 2021/06/08 TUE
setting number.
Clock Unit Clock Unit
24H 12H Now the setting value is flashing.
Time Time
00:00 12:00
NOTE Cursor moving order is :
Hour → Digit in ten minutes →
Digit in minutes
NOTE Setting range : 1~12(12H)
Date & Clock ●Example : To set the date to 2021.06.08. 0 ~23(24H)
Date ●Press the Adjust button to choose Default value : 12(12H)/0(24H)
2021/01/01 FRI the setting options.
Clock Unit
24H
Now the setting value is flashing.
Date & Clock ●EX : Set hour from 12:00 AM to 10:00 AM.
Time NOTE Setting range :
00:00
(year):2021 ~ 2099
Date ●Press the Adjust button to enter clock
2021/06/08 TUE
(month):1 ~ 12 adjustment minute setting.
Clock Unit
(day):1 ~ 31 12H
(Week) : MON, TUE, WED, Time
THU,FRI, SAT, SUN 10:00
wh081ba02a(P22-10)
5-2 Unit (Speed,Temperature) Setting
Unit ●The unit screen, press the Adjust button Unit ●Example : To set temp. unit to ˚F.
Speed for 3 seconds to enter the speed unit Speed ●Press the Select button to choose
km/h
setting. MPH the setting options.
Temperature Temperature
°C °C Now the setting value is flashing.
NOTE Setting range : ˚C (Celsius) and
˚F (Fahrenheit).
Default value : ˚C (Celsius).
Unit ●Example : To set speed unit as MPH. Unit ●EX : Set temp. unit from ˚C (Celsius)
Speed ●Press the Select button to choose Speed to ˚F (Fahrenheit).
km/h
the setting options. MPH ●Press the Adjust button to go back
Temperature Temperature to the unit (speed, temp.) screen.
°C Now the setting value is flashing. °F
Unit ●EX : Set speed unit from km/h to MPH. Unit ●The unit (speed, temp.) screen.
Speed ●Press the Adjust button to enter the Speed
MPH
temp. unit setting screen. MPH
Temperature Temperature
°C °F
Backlight ●Example : To set the gauge to Night Backlight ●Example : To set the backlight
Mode mode. Mode brightness (night) to 2/5(40%).
Auto ●Press the Select button to choose Night
●Press the Select button to choose the
Brightness (Day) the setting options. Brightness (Day)
setting number.
Brightness (Night) Now the setting value is flashing. Brightness (Night) Now the setting value is flashing.
NOTE Setting Auto(automatically NOTE Setting range :
switch according to the light : 1/5 (Darkest) ~ 5/5 (Brightest),
day mode display for a bright need ≦ the setting value of
environment and Night mode backlight brightness (day).
display for a dark environment), Setting unit : 20% per level.
Day mode, Night mode. Default value : 3/5(60%).
Default value : Auto.
NOTE The backlight brightness will
change immediately after
Backlight ●EX : Set background from Auto mode you set the value.
Mode to Night mode.
Night
●Press the Adjust button to enter the
Brightness (Day) backlight brightness (day) setting. Backlight ●EX : The backlight brightness (night)
Mode setting is changed from 3/5 (60%) to
Brightness (Night) Night
2/5 (40%).
Brightness (Day)
●Press the Adjust button to enter the
Brightness (Night) backlight color setting.
wh081ba02a(P22-11)
Backlight ●EX : Set backlight color from blue to Backlight ●The backlight screen.
Color white. Mode
White
●Press the Adjust button to go back Night
Brightness (Day)
to the backlight screen.
Brightness (Night)
Overspeed ●Example : To set speed warning Overspeed ●The speed warning screen.
Set value to 80 km/h. Set
060 km/h ●Press the Adjust button to move to 080 km/h
wh081ba02a(P22-12)
5-6 Overheat Warning Setting
Temp Warning ●The overheat warning screen, press the Temp Warning ●Example : To set overheat warning B
Temp A Adjust button for 3 seconds to enter the Temp A value to 150 ˚C.
090 °C overheat warning A setting. 120 °C
●Press the Adjust button to move to
Temp B Temp B
090 °C 090 °C
the digit you want to set.
Now the setting value is flashing.
NOTE Setting range : 60 ~250 ˚C
(140 ~482 ˚F).
Default value : 90 ˚C(194 ˚F).
Temp Warning ●Example : To set overheat warning A
Temp A value to 120 ˚C. Temp Warning ●Press the Select button to choose
090 °C
●Press the Adjust button to move to Temp A the setting number.
Temp B
090 °C
the digit you want to set. 120 °C
Temp B
Now the setting value is flashing. 090 °C
Temp Warning ●Press the Select button to choose Temp Warning ●EX : Set overheat warning B value from
Temp A the setting number. Temp A 90 ˚C to 150 ˚C.
090 °C 120 °C
●Press the Adjust button to go back to
Temp B
Temp B
090 °C 150 °C
the overheat warning setting.
Temp Warning ●EX : Set overheat warning A value from Temp Warning ●The overheat warning screen.
Temp A 90 ˚C to 120 ˚C. Temp A
120 °C
120 °C
●Press the Adjust button to enter the
Temp B Temp B
090 °C
overheat warning B setting. 150 °C
Volt Warning ●Example : To set low voltage warning Volt Warning ●Press the Select button to choose
Low value to DC 11.0 V. the setting number.
Low
11.5 V ●Press the Adjust button to move to 11.0 V
High the digit you want to set. High
15.0 V
15.0 V
Now the setting value is flashing.
NOTE Setting range : DC 8.0~13.0 V.
Default value : DC 11.5 V.
Volt Warning ●Press the Select button to choose Volt Warning ●EX : Set high voltage warning value
Low the setting number. Low from DC 15.0 V to DC 16.0 V.
11.5 V 11.0 V
●Press the Adjust button to go back to
High High
15.0 V 16.0 V
the voltage warning screen.
Volt Warning ●EX : Set low voltage warning value Volt Warning ●The voltage warning screen.
Low from DC 11.5 V to DC 11.0 V. Low
11.0 V
●Press the Adjust button to enter the 11.0 V
High High
15.0 V
high voltage warning setting. 16.0 V
wh081ba02a(P22-13)
5-8 Low Fuel Warning Setting
Low Fuel Warning ●The low fuel warning screen, press the Low Fuel Warning ●EX : Set low fuel warning value from
Set Adjust button for 3 seconds to enter Set 1/6 to 3/6.
the low fuel warning setting. ●Press the Adjust button to go back to
the low fuel warning screen.
Low Fuel Warning ●Example : To set low fuel warning Low Fuel Warning ●The low fuel warning screen.
Set value to 3/6 . Set
●Press the Select button to choose
the setting number.
Now the setting value is flashing.
NOTE Setting range : 0/6 ~ 3/6.
Default value : 1/6.
Service ●Example : To set mileage maintenance Service ●EX : Set the mileage maintenance
Function to (ON). Function from 500 km to 12,000 km.
ON ●Press the Select button to choose ON
●Press the Adjust button to return
Set the setting number. Set
to mileage maintenance main screen.
00500 km 12000 km
Now the setting value will blink.
NOTE Settings range : ON, OFF.
Default value : ON.
Service ●EX : Set mileage maintenance to (ON). Service ●The maintenance mileage screen.
Function ●Press the Adjust button to enter Function
ON into the mileage maintenance main ON
Set screen. Set
00500 km
NOTE When is set to OFF, will directly 12000 km
ABS Warning ●Example : To set ABS warning ABS Warning ●The ABS warning screen.
Function value to ON . Function
ON ●Press the Select button to choose ON
wh081ba02a(P22-14)
5-11 Warning Light Setting
Warning Light ●The warning light screen, press Warning Light ●Press the Adjust button to go back to
Overspeed the Adjust button for 3 seconds to Low Fuel Warning the warning light screen.
OFF enter the warning light setting. Flash
Warning Light ●Press the Select button to choose Warning Light ●The warning light screen.
Overspeed the setting number. Overspeed
OFF ●Press the Adjust button to confirm Steady
Shift Light
Now the setting value is flashing. Shift Light
Steady
NOTE Setting range : Flash
Learn Learn
Start CAUTION! Start
●You can use the tire Speedometer ●EX : Set the sensor point value from
valve as the starting Tire Circumference 01 P to 06 P.
point and the terminal 1300 mm ●Press the Adjust button to enter the
point to measure the Sensor Point learning mode setting.
wheel circumference 06 P
with a measuring tape. Learn
Start
wh081ba02a(P22-15)
Speedometer ●Press the Select button to start the Speedometer ●The tire circumference and sensor
Tire Circumference learning mode. Tire Circumference point screen.
1300 mm 1300 mm
Sensor Point Sensor Point
06 P 06 P
Learn Learn
Start Start
GO!
Ready
Tire-Learn
Count :
Abort!
Learn
●Press the Select button to choose to cancel the gear learning.
the setting options.
OFF
Start
●When N→1 appears, change
Now the setting value is flashing. to Gear 1 to ride.When Gear 1 is
NOTE Setting range : ON, OFF. detected, 1→2 appears and then
Default value : ON. change to Gear 2.
Gear - Learn
Learn
Start
wh081ba02a(P22-16)
5-14 RPM Input Pulse & Signal & Range
RPM ●The RPM input pulse, signal & Range RPM ●EX : Set the signal from
Pulse screen, press the Adjust button for 3 Pulse High-Act to Low-Act.
1 seconds to enter the RPM input pulse, 2 ●Press the Adjust button to enter
Signal signal & Range setting. Signal the RPM Range setting.
High-Act Low-Act
Range Range
10000 RPM 10000 RPM
RPM ●Example : You want to set the RPM RPM ●Example : Set the RPM Range to
Pulse input pulse to 2 (4 Stroke, 4 piston). Pulse 15000 RPM.
1 ●Press the Select button to choose 2 ●Press the Select button to choose
Signal the setting number. Signal the setting options.
High-Act Low-Act
Range
Now the setting value is flashing. Range
Now the setting value is flashing.
10000 RPM NOTE Setting range : P-0.5, 1.0~24.0. 10000 RPM
NOTE Setting range : 10000 RPM,
Default value : 1.0. 12500 RPM,15000 RPM,
18000 RPM.
The The correspond- The corresponding RPM signal Default value : 10000 RPM.
setting ing stroke and number per ignition.
value pistons number.
0.5 4C-1P 2 RPM signals per 1 ignition.
1.0 2C-1P 4C-2P 1 RPM signal per 1 ignition.
RPM ●EX : The RPM Range setting is
2.0 2C-2P 4C-4P 1 RPM signal per 2 ignition.
Pulse changed from10000 RPM to
3.0 2C-3P 4C-6P 1 RPM signal per 3 ignition. 2 15000 RPM.
4.0 2C-4P 4C-8P 1 RPM signal per 4 ignition. Signal ●Press the Adjust button to go back to
5.0 4C-10P 1 RPM signal per 5 ignition. Low-Act
6.0 2C-6P 4C-12P 1 RPM signal per 6 ignition.
the RPM input pulse & Signal Impulse
Range
15000 RPM
& Range screen.
CAUTION!
Most of the 4-cycle bikes with one single
piston are igniting once every360 degree,
so the setting should be the same as the
bike with 2-cycle and one piston engine.
RPM ●EX : The RPM input pulse setting is RPM ●The RPM input pulse, signal
Pulse changed from1.0 to 2.0. Pulse & Range screen.
2
●Press the Adjust button to enter the 2
Signal
signal impulse setting. Signal
High-Act Low-Act
Range Range
10000 RPM 15000 RPM
Range
Now the setting value is flashing.
10000 RPM
NOTE Setting range :High-Act, Low-Act.
Default value : High-Act.
wh081ba02a(P22-17)
5-15-1 Fuel Gauge Resistance Setting (Manual)
Fuel ●Press the Adjust button to enter the Fuel-Custom ●Example : To set the highest fuel level
Type fuel gauge resistance setting(manual). Empty resistance value as 10 Ω.
Custom
●Example : For YAMAHA T-MAX 530, Manual 0090 Ω
●Press the Adjust button to move to
Full
according to the service manual, the Manual 0010 Ω
the digit you want to set.
fuel tank resistance from low to high Now the setting value is flashing.
is 90 - 100 Ω (the lowest) and 4 - 10 Ω
(the highest).So enter the setting
value as 10 Ω .
wh081ba02a(P22-18)
5-16 A/F Ratio Setting
A/F Ratio ●The A/F ratio screen, press the Adjust A/F Ratio ●Press the Adjust button to go back to
Function button for 3 seconds to enter the A/F Function the A/F ratio screen.
OFF
ratio setting. ON
A/F Ratio ●Example : To set A/F ratio warning A/F Ratio ●The A/F ratio screen.
Function function to ON. Function
OFF ●Press the Select button to choose ON
Sort by Sort by
Sequence Sequence
Power Test ●Example : To set target speed Power Test ●EX : Set target distance value from
Target Speed value to 110 km/h. Target Speed 50 m to 100 m.
050 km/h
●Press the Adjust button to move to 110 km/h ●Press the Adjust button to enter the
Target Distance
the digit you want to set. Target Distance the record order setting.
0050 m 0100 m
wh081ba02a(P22-19)
5-18 Internal and External ODO Setting
ODO ●The internal and external ODO screen, ODO ●EX : Set external total distance value
Total press the Adjust button for 3 seconds Total from 000,000 km to 12,500 km.
050000 km to enter the external ODO setting. 050000 km
●Press the Adjust button to go back
Set Set
000000 km User unable to adjust or clear 012500 km
to the internal and external ODO screen.
internal ODO.
NOTE Display range :0~999,999 km (mile).
ODO ●Example : To set external total distance ODO ●The internal and external ODO screen.
Total value to 12,500 km. Total
050000 km
●Press the Adjust button to move to 050000 km
Set Set
000000 km
the digit you want to set. 012500 km
2
1
0
x1000RP
TCS
OFF
MOD
A
wh081ba02a(P22-20)
5-20 Bluetooth® Setting
Bluetooth ●The Bluetooth® screen, press the ●Enter the code displayed on
Set Adjust button for 3 seconds to “KOSO RX4.”
ON enter the Bluetooth® setting.
Mobile OS
iOS Bluetooth
Device Name: KOSO_RX4 Set
Mobile Device: Uconnected ON
mobile phone.
●Press device “KOSO RX4.”
1.
2. Bluetooth ●The Bluetooth® screen.
Set NOTE After the Bluetooth® is successfully
ON
connected, the main screen may
Mobile OS
iOS
display the battery, incoming phone
call notice, incoming online call
Device Name: KOSO_RX4
notice,music playing message,
Mobile Device: Connected
information of the mobile phone.
4
Phone battery Push notification
7 8 9 10 11 12
4 ●Phone battery.
4 ●Push notification screen.
4 5 6 7 8 9 10 4 5 6 7 8 9 10
3 3
3000 RPM 3000 RPM
400060 60
GEAR GE A R
60
2 2
RPM
1 1
1 1
GEAR
0 1/2 0 1/2
x1000RPM x1000RPM
km/h km/h
105.2 °C 67.9 °C 105.2 °C 67.9 °C
0 0
KOSO
ODO Tong.21528
Good afternoon!
12.5 v 12.5 v
1
ODO 21528 km Trip A 729.5 km km Trip A 729.5 km
km/h
5 V 95 °C
0
9 hr Trip 1 9999.9 km
wh081ba02a(P22-21)
Incoming phone call notice/ Music playing info
Incoming online call notice
4 ●Music playing info screen.
4 5 6 7 8 9 10
3
3000 RPM
4
60
●Incoming phone call notice screen.
GE A R
4 5 6 7 8 9 10
2
3
3000 RPM ●Incoming online call notice screen.
60
1
GEAR
2 1 0 km/h
x1000RPM
Hello
1
0 1/2 Adele
x1000RPM 12.5 v
km/h 01:20/06:06
KOSO-Tong Yah 0
12.5 v
4 4
4 5 6 7 8 9 10 4 5 6 7 8 9 10
3 3
3000 RPM
60
3000 RPM
60
GEA R GEAR
2 1 2 1
1 1
0 1/2 0 1/2
x1000RPM
km/h
x1000RPM
km/h
KOSO-Tong Yah 0
105.2 °C 67.9 °C
0
12.5 v 12.5 v ODO 21528 km Trip A 729.5 km
NOTE ●Incoming phone call notice screen. NOTE Song title: 15 letters, and “…” displayed if > 15 letters
Display range : Display name or number for up to Artist name: 18 letters, and “…” displayed > 18 letters
12 letters; “…” is displayed if > 12 letters; Total length of the song:00:00 ~ 9:59:59,
“Unknown” is displayed when there is no name
“9:59:59” displayed if longer.
iOS - Display either name or number of the incoming call
Android - Display number only →iOS supported, not Android.
●Incoming online call notice screen. Current playing time : 00:00 ~ 9:59:59,
Display range : Display name for up to 12 letters; “9:59:59” is displayed if longer.
“…” is displayed if >12 letters; →Support iOS supported, not Android.
“Unknown” is displayed when there is no name
→ Support LINE, WeChat, WhatsApp
→ iOS supported, not Android.
※ “The Company is committed to optimizing the Bluetooth® application function of the meter. However, as supports for software and hardware are
different as mobile phones differ, the Bluetooth® application function of the meter may be affected, causing differences in functions.”
6 Trouble Shooting
The following situations do not necessarily indicate malfunction of the product. Check the following points, before contacting us.
Trouble Check item Trouble Check item
The meter doesn't work ●The power isn't supplied to the meter. A/F ratio doesn't appear ●Check the setting.
when the power is on. →Make sure the wiring is connected. or appears incorrectly. →Refer to the manual 5-16 A/F ratio
The wiring and fuse are not broken. setting.
→The battery is too old to supply needed Fuel meter doesn't display ●Check your fuel tank.
power (DC 12 V). or displays error. ●May be poor connection of the harness.
The meter shows wrong ●Check the voltage of your battery, and →Make sure the wires are
information. make sure the voltage is over DC 12 V. connected correctly.
Speed meter doesn't appear ●May be poor connection of the speed ●Check the setting.
or appears incorrectly. sensor. →Check the settings menu, the
→Check the speed sensor is fuel settings are correct.
connected correctly. The clock is incorrect. ●Check the setting.
●Check the setting. →Check the settings menu, the
→Refer to the manual 5-12 circumference clock settings are correct.
and sensing point setting. ●May be due to the reversed power line.
Tachometer doesn't appear ●Make sure the RPM wire is connected →Check the positive wire(Red)
or appears incorrectly. properly. connects to the battery(DC 12 V), and
→Check the RPM wire wire is connected main switch positive wiring(Brown)
correctly. connects to the main switch(DC 12 V).
●Check the spark plug is R type or Voltage doesn't ●May be due to poor connection of wiring.
not. If not, replace the spark plug appear or appears →Check whether the wires are
with the R type spark plug. incorrectly. disconnected or have fallen off.
●Check the setting. The meter indicator ●May be poor connection of the harness.
→Refer to the manual 5-14 RPM input pulse, didn't display. →Make sure the wires are
signal and Range.
connected correctly.
Thermometer doesn't appear ●Make sure the temperature wire is
or appear incorrectly. connected properly.
→Check the temperature wire is
connected correctly.
●Check the setting.
→Check whether it is set to the
air-fuel ratio function.
※ If the problems still can’t be solved, contact our technical department for assistance.
Android™ is a registered trademark of Google LLC. Apple® and iPhone® is a trademarks of Apple Inc., registered in the U.S. and other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Tong Yah Electronic
Technology Co.,Ltd is under license. Other trademarks and trade names are those of their respective owners.
wh081ba02a(P22-22)