Professional Documents
Culture Documents
Toyota Camry Body Electrical
Toyota Camry Body Electrical
PRECAUTION
Take care to observe the following precautions when performing inspections or removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM
Halogen bulbs have pressurized gas inside and require special handling. They can burst if scratched
or dropped. Hold a bulb only by its plastic or metal case. Don’t touch the glass part of a bulb with bare
hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The CAMRY is equipped with an SRS (Supplemental Restraint System) such as the driver airbag and
front passenger airbag. Failure to carry out service operation in the correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing
(including removal or installation of parts, inspection or replacement), be sure to read the precaution-
ary notices in the RS section.
3. AUDIO SYSTEM
If the negative (–) terminal cable is disconnected from the battery, the preset AM, FM 1 and FM 2 sta-
tions stored in memory are erased, so make sure to note the stations and reset them after the negative
(–) terminal cable is reconnected to the battery.
If the negative (–) terminal cable is disconnected from the battery, the ”ANTI–THEFT SYSTEM” will
operate when the cable is reconnected, but the radio, tape player and CD player will not operate. Be
sure to input the correct ID number so that the radio, tape player and CD player can be operated again.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to precautions in the IN section.
1. Headlight Bulb –
Only one side light does not light. 2. HEAD LO (LH, RH) Fuse (E/G Room R/B No.2) –
3. Wire Harness –
1. Headlight Bulb –
2. HEAD LO (LH, RH) Fuse (E/G Room R/B No.2) –
3. Headlight Control Relay (E/G Room J/B No.2) BE–24
”Lo–Beam” does not light.
4. Integration Relay (I/P J/B No.1) BE–14
5. Light Control Switch BE–24
6. Wire Harness –
1. Headlight Bulb –
2. ECU–B Fuse (E/G Room J/B No.2) –
3. HEAD HI (LH, RH) Fuse (E/G Room J/B No.2) –
4. DRL Fuse (E/G Room R/B No.2) –
5. Daytime Running Light Relay No.2 –
(E/G Room R/B No.2) BE–24
”Hi–Beam” does not light. 6. Daytime Running Light Relay No.3 –
(E/G Room R/B No.2) BE–24
7. Daytime Running Light Relay No.4 –
(E/G Room R/B No.2) BE–24
8. Daytime Running Light Relay (Main) BE–24
9. Headlight Dimmer Switch BE–24
10.Wire Harness –
1. Headlight Bulb –
2. ECU–B Fuse (E/G Room J/B No.2) –
3. HEAD HI (LH, RH) Fuse (E/G Room J/B No.2) –
4. DRL Fuse (E/G Room R/B No.2) –
5. Daytime Running Light Relay No.2 –
(E/G Room R/B No.2) BE–24
”Flash” does not light. 6. Daytime Running Light Relay No.3 –
(E/G Room R/B No.2) BE–24
7. Daytime Running Light Relay No.4 –
(E/G Room R/B No.2) BE–24
8. Daytime Running Light Relay (Main) BE–24
9. Headlight Dimmer Switch BE–24
10.Wire Harness –
1. Headlight Bulb –
2. ECU–B Fuse (E/G Room J/B No.2) –
3. GAUGE Fuse (I/P J/B No.1) –
Headlight does not light with engine running and light control SW
4. HEAD HI (LH, RH) Fuse (E/G Room J/B No.2) –
OFF.
5. Daytime Running Light Relay (Main) BE–24
6. Wire Harness –
7. Other Parts* –
1. Bulb –
Rear Combination light does not light. 2. Light Failure Sensor BE–37
3. Wire Harness –
1. GAUGE Fuse (I/P J/B No.1) –
2. Integration Relay (I/P J/B No.1) BE–14
”Auto Turn–off System” does not operate.
3. Door Courtesy Switch (Driver’s) BE–24
4. Wire Harness –
1. Bulb –
Only one bulb does not light up.
2. Wire Harness –
1. Bulb –
Dome light does not light up. 2. Dome Light BE–32
3. Wire Harness –
1. Bulb –
Map Light does not light up. 2. Map Light BE–32
3. Wire Harness –
1. Bulb –
Luggage compartment light does not light up. 2. Luggage compartment door courtesy switch BE–32
3. Wire Harness –
1. Bulb –
Only one light does not light up.
2. Wire Harness –
COMBINATION METER
METER, GAUGES AND ILLUMINATION:
Symptom Suspect Area See page
1. GAUGE Fuse (I/P J/B No.1) –
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
2. Meter Circuit Plate BE–46
do not operate.
3. Wire Harness –
1. No.1 Vehicle Speed Sensor BE–47
Speedometer does not operate. 2. Meter Circuit Plate BE–46
3. Wire Harness –
1. Igniter (5S–FE) IG–1
(1MZ–FE) IG–1
Tachometer does not operate.
2. Meter Circuit Plate BE–46
3. Wire Harness –
1. Fuel Receiver Gauge BE–47
2. Fuel Sender Gauge BE–47
Fuel Gauge does not operate or abnormal operation.
3. Meter Circuit Plate BE–46
4. Wire Harness –
COMBINATION METER
WARNING LIGHTS:
Symptom Suspect Area See page
1. GAUGE Fuse (I/P J/B No.1) –
Warning lights do not light up. (Except Discharge, Open Door and
2. Meter Circuit Plate BE–46
SRS)
3. Wire Harness –
1. Bulb –
2. Low Oil Pressure Warning Switch BE–47
Low Oil Pressure warning light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
2. Fuel Level Warning Switch BE–47
Fuel Level warning light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
ABS warning light does not light up. 2. ABS ECU IN–31
3. Wire Harness –
1. Bulb –
2. Seat Belt Buckle Switch BE–47
Seat Belt warning light does not light up.
3. Integration Relay (I/P J/B No.1) BE–47
4. Wire Harness –
COMBINATION METER
INDICATOR LIGHTS:
Symptom Suspect Area See page
1. Bulb –
2. O/D OFF Switch (A140E) DI–431
O/D OFF indicator light does not light up. (A541E) DI–487
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
2. Cruise Control ECU IN–31
Cruise Control indicator light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
2. Meter Circuit Plate BE–46
High beam indicator light does not light up.
3. Wire Harness –
4. Headlight System BE–22
1. Bulb –
2. Meter Circuit Plate BE–46
Turn indicator light does not light up.
3. Wire Harness –
4. Turn Signal and Hazard Warning System BE–29
1. Bulb –
2. Meter Circuit Plate BE–46
Shift indicator lights do not light up. 3. Park/Neutral Position Switch (A140E) DI–424
(A541E) DI–479
4. Wire Harness –
1. Bulb –
Only one shift indicator does not light up.
2. Meter Circuit Plate BE–46
1. Bulb –
2. ECM –
Malfunction indicator light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
2. Traction ECU –
SLIP indicator light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
2. Traction ECU –
TRAC OFF indicator light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
1. Bulb –
2. Security ECU –
Security indicator light does not light up.
3. Meter Circuit Plate BE–46
4. Wire Harness –
Indicator lights do not light up. (Except Turn, Hi–beam and 1. GAUGE Fuse (I/P J/B No.1) –
security) 2. Wire Harness –
DEFOGGER SYSTEM
Symptom Suspect Area See page
1. DEFOG M–Fuse (I/P J/B No.1) –
2. HTR Fuse (I/P J/B No.1) –
All defogger systems do not operate. 3. Defogger Relay (I/P J/B No.1) BE–56
4. Defogger Switch BE–56
5. Wire Harness –
1. Defogger Wire BE–56
Rear window defogger does not operate. 2. Choke Coil –
3. Wire Harness –
1. MIR/HTR Fuse (I/P J/B No.1) –
Mirror defogger does not operate. 2. Mirror Defogger BE–56
3. Wire Harness –
POWER WINDOW CONTROL SYSTEM
Symptom Suspect Area See page
1. POWER M–Fuse (I/P J/B No.1) –
Power window does not operate (ALL).
2. Power Main Relay (I/P J/B No.1) BE–60
(Power Door Lock does not operate)
3. Wire Harness –
1. Ignition Switch BE–14
Power window does not operate (ALL).
2. Power Window Master Switch BE–60
(Power Door Lock is normal)
3. Wire Harness –
”One Touch Power Window System” does not operate. 1. Power Window Master Switch BE–60
1. Power Window Master Switch BE–60
2. Power Window Switch BE–60
Only one window glass does not move.
3. Power Window Motor BE–60
4. Wire Harness –
”Window Lock System” does not operate. 1. Power Window Master Switch BE–60
”Window Lock Illumination” does not light up. 1. Power Window Master Switch BE–60
1. GAUGE Fuse (I/P J/B No.1) –
2. Integration Relay (I/P J/B No.1) BE–60
Key–off power window does not operate. 3. Ignition Switch BE–14
4. Door Courtesy Switch BE–32
5. Wire Harness –
Power seat does not operate. 1. Power Seat Swtich (D,P) BE–78
(Door lock system is normal) 2. Wire Harness –