Professional Documents
Culture Documents
Actualizacion GPS 430 530W
Actualizacion GPS 430 530W
18 December 2015
Revision A, 21 July 2016
Revision B, 27 November 2019
MODEL AFFECTED: 429
DESCRIPTION:
This bulletin enables maintenance personnel to perform an “On Aircraft” Field Loadable
Software (FLS) upgrade of the GNS 530W/430W series units which changes and/or
improves a number of their capabilities and features as described in the Garmin Aviation
Service Document Notifications (ASDN) referenced in Appendix A.
TB 429-15-41-RB
Page 1 of 17
Approved for public release.
DESCRIPTION: (Continued)
The initial release of this bulletin was applicable only to the helicopters listed in the
HELICOPTER AFFECTED block that operated in the Australian airspace.
Revision A made this bulletin applicable to all helicopters listed in the HELICOPTERS
AFFECTED block regardless of their geographical location.
Applicability of this bulletin to any spare part shall be determined prior to installing the
part on any affected Bell model 429 helicopter.
-NOTE-
-NOTE-
-NOTE-
-NOTE-
TB 429-15-41-RB
Page 2 of 17
Approved for public release.
APPROVAL:
The engineering design aspects of this bulletin are Transport Canada Civil Aviation
(TCCA) approved.
CONTACT INFO:
MANPOWER:
Approximately 4.0 man-hour is required to complete this bulletin. This estimate is based
on hands-on time and may vary with personnel and facilities available.
WARRANTY:
There is no warranty credit applicable for parts or labor associated with this bulletin.
MATERIAL:
Required Material:
The following material is required for the accomplishment of this bulletin and may be
obtained through your Bell Helicopter Textron Supply Center.
Consumable Material:
None required.
SPECIAL TOOLS:
None required.
Not affected.
TB 429-15-41-RB
Page 3 of 17
Approved for public release.
ELECTRICAL LOAD DATA:
Not affected.
REFERENCES:
PUBLICATIONS AFFECTED:
ACCOMPLISHMENT INSTRUCTIONS:
PART I:
2. While the GNS unit is turned off, press and hold the ENT key and then turn the unit
on. Release the ENT key when the display activates. After the Data Base and
Instrument Panel Self-test pages (Press ENT for “OK” for each page), the first page
displayed when in Configuration Mode Operation is the MAIN ARINC 429 CONFIG
page. In this mode, pages can be selected by ensuring the cursor is off and
rotating the small right knob clockwise, where each configuration page will be
displayed one after the other.
3. Note the GNS 430W unit(s) configuration settings (by circling or writing them) on
the record sheets provided in the following pages for:
TB 429-15-41-RB
Page 4 of 17
Approved for public release.
GNS 430W No. 1 (if installed) / GNS 430W No. 2
CONFIGURATION SET-UP RECORD SHEET
(A)
TB 429-15-41-RB
Page 5 of 17
Approved for public release.
GNS 430W No. 1 (if installed) / GNS 430W No. 2
CONFIGURATION SET-UP RECORD SHEET (Continued)
(B)
TB 429-15-41-RB
Page 6 of 17
Approved for public release.
GNS 430W No. 1 (if installed) / GNS 430W No. 2
CONFIGURATION SET-UP RECORD SHEET (Continued)
(C)
Important: If the aircraft has been custom modified per Bell drawings 429-799-XXX or 429-
899-XXX, or by a third party organization, and the GNS unit configuration requires particular
settings; refer to these drawings for details.
1 If TCAD 9900BX kit is installed, set GNS 430W No. 1 to OFF and set GNS 430W No. 2 to Traffic Advisory.
2 To enable the GAMA429 NONSTD option, initially select the pushbuttons for DIR-TO, ENT, and MENU keys, in
that order. If Speed = HIGH, reselect the GAMA 429 option in order to modify the HIGH/LOW speed to LOW and
then reselect GAMA429 NONSTD from the list.
3 Set GNS 430W No. 1 to LNAV 1. Set GNS 430W No. 2 to LNAV 2.
4 If TCAD 9900BX kit (BHT-429-II-24 / 429-706-017) is installed, set GNS 430W No. 1 as follows: INPUT = RYAN
TCAD, OUTPUT = RYAN TCAD. Set GNS 430W No. 2 to OFF, as shown in the Table.
5 Press/rotate the outer right side knob to highlight/change CONFIGURE fields between FUEL, TERRAIN, and
Discretes.
6 Select item shown in italics and press ENT key. Setting as shown (...).
7 Press the MENU key to access options and then ENTER to accept.
8 For each frequency selected, after all settings, select STORE CALIBRATION and press ENT once to store.
9 Set GNS 430W No. 1 to VOR/ILS 1. Set GNS 430W No. 2 to VOR/ILS 2.
10 Set GNS 430W No. 1 to directed frequency 1. Set GNS 430W No. 2 to directed frequency 2.
11 If HTAWS Kit (BHT-429-II-49 / 429-706-275) is installed; set GNS 430W to TER PROX.
13 If HTAWS Kit (BHT-429-II-49 / 429-706-275) is installed and enabled, set GNS 430W to ENABLED. Without
HTAWS, set GNS 430W to DISABLED.
TB 429-15-41-RB
Page 7 of 17
Approved for public release.
4. Access the GNS 530W unit (If installed) configuration pages by entering the
Configuration Mode Operation and note its configuration settings (by circling or
writing them) on the record sheets provided in the following pages. While the GNS
unit is turned off, press and hold the ENT key and then turn the unit on. Release
the ENT key when the display activates. After the Data Base and Instrument Panel
Self-test pages (Press ENT for “OK” for each page), the first page displayed when
in Configuration Mode Operation is the MAIN ARINC 429 CONFIG page. In this
mode, pages can be selected by ensuring the cursor is off and rotating the small
right knob clockwise, where each configuration page will be displayed one after the
other.
TB 429-15-41-RB
Page 8 of 17
Approved for public release.
GNS 530W (If installed) CONFIGURATION SET-UP RECORD SHEET (Continued)
(B)
TB 429-15-41-RB
Page 9 of 17
Approved for public release.
GNS 530W (If installed) CONFIGURATION SET-UP RECORD SHEET (Continued)
(C)
TB 429-15-41-RB
Page 10 of 17
Approved for public release.
GNS 530W (If installed) CONFIGURATION SET-UP RECORD SHEET (Continued)
(D)
Important: If the aircraft has been custom modified per Bell drawings 429-799-XXX or 429-899-XXX, or
by a 3rd party organization, and the GNS unit configuration requires particular settings; refer to these
drawings for details.
1 If TCAD 9900BX kit (BHT-429-II-24 / 429-706-017) is installed; set GNS 530W to OFF.
2 To enable the GAMA429 NONSTD option, initially select the pushbuttons for DIR-TO, ENT, and MENU keys, in
that order. If Speed = HIGH, reselect GAMA 429 option in order to modify the HIGH/LOW speed to LOW and
then reselect GAMA429 NONSTD from list.
3 If TCAD 9900BX kit is installed, set GNS 530W as follows: INPUT = RYAN TCAD, OUTPUT = RYAN TCAD.
4 Press/rotate outer right side knob to highlight/change CONFIGURE fields between FUEL, TERRAIN, and
Discretes.
5 Select item shown in italics and press ENT key. Setting as shown (...).
7 For each frequency selected, after all settings, select STORE CALIBRATION and press ENT once to store.
8 If HTAWS Kit (BHT-429-II-49 / 429-706-275) is installed; set GNS 530W to HTAWS. If HTAWS is not installed;
set Terrain Type to TER PROX and set HW Config to TERRAIN.
9 To test terrain data card, select Main System Configuration page, select TERRAIN in the CONFIGURE field, and
TERRAIN TYPE (HTAWS). Highlight the TEST CARD field and press the ENT key. The TEST CARD field
indicates PASS. A FAIL condition indicates that the terrain data card is unusable.
10 Configuration setup only applicable when HTAWS Kit (BHT-429-II-49 / 429-706-275) is installed.
12 If HTAWS Kit (BHT-429-II-49 / 429-706-275) is installed and enabled, set GNS 530W to ENABLED. Without
HTAWS installed; set GNS 530W to DISABLED.
TB 429-15-41-RB
Page 11 of 17
Approved for public release.
-NOTE-
1. With the GNS No. 1 unit switched “OFF” (upper GNS 430W or GNS 530W, as
shown on Figure 1 or 2); remove the TERRAIN DATABASE CARD from the right-
hand card slot in the front of the unit (Figures 3 or 4).
2. Insert the GNS 400W/500W series MAIN software loader card (P/N 010-00446-
25) in the right-hand card slot. Make sure the card is firmly seated (Figures 3 or 4).
TB 429-15-41-RB
Page 12 of 17
Approved for public release.
3. Turn “ON” the unit. Instructions to press ENT will be displayed immediately. Press
ENT and follow all on-screen prompts.
4. The update will take less than one (1) minute to complete. After the update has
completed, turn the unit “OFF”.
5. If updating from main software Version 4.xx or earlier, repeat step 3 and step 4.
7. Remove the software loader card and insert the TERRAIN DATABASE CARD
removed in step 1. Make sure the card is seated firmly.
8. Turn the unit “ON”. After the unit has initialized, use the right knob to get to the
AUX | UTILITY | SOFTWARE VERSIONS page.
a) Use the large right knob to change the page group and select the Aux Group
page.
b) Use the small right knob to select the page within the group and select the
Utility page
c) Within the Utility page, select the SOFTWARE VERSION line and press
ENTER to view the software versions page.
10. This completes the MAIN software (Version 5.20) upload for the GNS No. 1 unit.
(i.e., upper GNS 430W or GNS 530W)
11. Repeat step 1 through 10 for GNS 430W No. 2 (lower GNS unit, as shown on
Figure 1 or 2)
12. This completes the MAIN software (Version 5.20) upload for the GNS 430W No. 2
unit.
TB 429-15-41-RB
Page 13 of 17
Approved for public release.
PART III - GPS software (Version 5.0) upload procedure.
1. With the GNS No. 1 unit switched “OFF” (upper GNS 430W or GNS 530W, as
shown on Figure 1 or 2); remove the AVIATION DATABASE CARD from the left-
hand card slot in the front of the unit (Figures 3 or 4).
2. Insert the GNS 400W/500W series GPS software loader card (P/N 010-00706-
20) into the left card slot. Make sure the card is firmly seated.
3. Turn the unit ON. Instructions to press ENT will be displayed immediately. Press
ENT and follow all on-screen prompts.
4. The update will take several minutes to complete. After the update is complete,
turn the unit OFF.
5. Remove the software loader card and insert the Aviation database card removed in
step 1. Make sure the card is firmly seated.
6. Turn the unit ON and verify the GPS software Version 5.0 is displayed on the
screen during initialization. (The GPS software version can also be viewed by
turning the right knob and viewing the AUX | UTILITY | SOFTWARE VERSION
page.)
7. This completes the GPS software (Version 5.0) upload for the GNS No. 1 unit.
(Upper GNS 430W or GNS 530W)
8. Repeat step 1 through 6 for GNS 430W No. 2 (Lower GNS unit)
9. This completes the GPS software (Version 5.0) upload for the GNS 430W No. 2.
TB 429-15-41-RB
Page 14 of 17
Approved for public release.
PART IV - Configuration set-up, Verifications, and Records
1. Turn both units ON. After the units have initialized, use their respective right knobs
to get to the AUX | UTILITY | SOFTWARE VERSION page.
2. Confirm the software version for MAIN SW is 5.20 and GPS SW is 5.0 on both
units.
3. Perform and/or verify the configuration of GNS 430W No.1 (If installed) and/or GNS
430W No.2 (are) setup as noted in PART I of this bulletin. As required; consult the
notes at the end of the appropriate Configuration Set-Up Record Sheets for
additional information.
4. Perform and/or verify the configuration of GNS 530W (If installed) is setup as noted
in PART I of this bulletin. As required; consult the notes at the end of the
appropriate Configuration Set-Up Record Sheets for additional information.
-NOTE-
TB 429-15-41-RB
Page 15 of 17
Approved for public release.
6. If installed, do the GNS-430W No. 2 operational checks.
-NOTE-
9. Make an entry in the helicopter logbook and historical service records indicating
compliance with this Technical Bulletin and keep this record for future use or
reference.
TB 429-15-41-RB
Page 16 of 17
Approved for public release.
APPENDIX A
For additional information on Garmin aviation products; please use the following
link
http://garmin.blogs.com/aviationalerts/service-document-notifications/
TB 429-15-41-RB
Page 17 of 17
Approved for public release.