Professional Documents
Culture Documents
Brushbond Flxiii
Brushbond Flxiii
Brushbond Flxiii
Uses Properties
Brushbond FLXIII when fully cured, provides a seamless Pot life at 35ºC : Approx. 1 hour
elastic waterproof membrane for use in roof areas, wet areas, Adhesion to substrate : 1 N/mm2
pre-cast joints where a tough elastomeric water tight (ASTM D4541:1989)
membrane is required. Shore A hardness : 62
(ASTM D2240:1997)
Advantages Tensile strength (N/mm2 ) : 0.9 N/mm2
! Can be applied to damp substrates (ASTM D412-91)
Elongation at break : 127%
! No primer required (ASTM D412-91)
! Elastomeric - able to bridge cracks Water Permeability : Nil
(DIN 1048:Pt 5: 1991)
! Able to take foot traffic when cured Water vapour transmission : 0.632 g/hr-m²
! Factory pre-blended two component system ensure (ASTM E96:1995)
quality control at site Crack bridging : Passed
Low Temperature Flexibility : Passed
Description (ASTM C 765:1993)
Setting time *
Brushbond FLXIII is a two component polymer modified - Foot traffic : 4 hrs + 1 hr
waterproof membrane which is supplied in readymix kits. - Light vehicle : 24 hrs + 3 hrs
When mixed, an easily brushable coating is produced. It can
simply be applied by a stiff brush, roller, or trowel to obtain the Note*: On clean dry concrete, with adequate airflow
desired thickness. (ventilation) at 25ºC to 35ºC
Application Estimating
For best results damp the surface before coating with Supply
Brushbond FLXIII. Use a short, stiff bristle brush preferably Brushbond FLXIII Kit : 15 litres pack
120 to 200 mm in width. Apply like a paint using one or two Powder : 14.8 kg
coats as required. Liquid : 10 kg
For trowel application, ensure that the substrate is levelled Coverage / yield
and repaired of any undulations or pot holes. Brushbond FLXIII : 15m²/pack applied at 1mm
thick (2 coats of 500
Brushbond FLXIII should be applied to the recommended
microns thick)
coverage as follows:
Note: Coverage figures are theoretical and due to wastage
It is recommended that general re-surfacing and areas
factors and the variety nature of possible substrates,
subjected to light foot traffic should receive a Brushbond FLXIII
practical coverage will be reduced.
in two coats of 500 microns each to give a 1mm thick coating.
Additional coatings may be required for areas of moderate to
Storage
heavy pedestrian conditions.
Brushbond FLXIII has a shelf life of 6 months in unopened
Cleaning
pack, kept in a dry store. In high humidity locations, the shelf
Brushbond FLXIII should be removed from tools and life may be reduced to 4 months.
equipment immediately after use with clean water. Hardened
material can only be removed mechanically. Precautions
Limitation
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard
Conditions for the Supply of Goods and Service
Head Office
Al Gurg Fosroc telephone: (+9714) 2858606 fax: (+9714) 2859649 email: agf@fosroc.com
LLC Regional offices
Dubai, Al Gurg Fosroc telephone: 285 8787 fax: 285 2023 email: dubai@fosroc.com
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17735454 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
www.fosroc.com
Oman, Al Amana telephone: 771 5080 fax: 771 7554 email: oman@fosroc.com
Qatar, Tadmur telephone: 413628 fax: 440812 email: qatar@fosroc.com
UAE/0288/04/G