Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 2

INSPECTION CERTIFICATE OF LIFTING GEAR

This report complies with the requirement of BS standards

Test Engineer Report:


Work No: DT-D-20- Certificate No: DT-
Details of Owner of the Lifting Gear / Customer Details:
Details of the Manufacturer/Supplier of the Lifting Gear:
Site Location:
Inspection Requested by:
Nature/Type of Inspection:
Visual / Periodic / initial / Major
Details of Previous Inspection and Test:
BS EN 13414-1:2003+A2:2008, BS EN 13414-1:2003+A2:2008,
Reference Standards:
BS EN 13414-3:2003+A1:2008
Dubai Local Regulation # 2/2010
Local Regulations:
Dubai Municipality (EIAC-RQ-IB-001) -(EIAC-RQ-IB-002)
Test Method Used: DT-IP-01
Test Equipment Details:
Defects noted and alterations or repairs required before is put
into service (If none enter “NONE”)
Date of Test and Examination: Date Due and Validity:
Distinguishing Number Working Load
Number or Description of item tested Limit, WLL REMARKS
Mark (tonne)
Wire rope sling
Make :

Rope grade :

Rope Diameter :

EWL :

Safety Factor :

NOTE: The validity of the certificate 6 months ceases in the event that any repair or alteration made, in which case it must be retested.
The inspection certificate/report shall not be reproduced except in full without the approval of the inspection body and the client.

We, Dutech Safety & security Consultancies, Dubai, certify that the below particulars are correct and Lifting gear described herein is
inspected and tested by a competent person, according to BS Standards. At the time of inspection the Equipment has been found to be free from
any adverse qualities that can affect its safe use and it is safe for its intended use. Please see the recommendations detailed report overleaf.

Inspected By: Verified By:

(Signature) (Signature)
NISARUDEEN RETHEESH REGHU
(Inspection Engineer) (General Manager)

The certificate is issued subject to the condition that is understood and agreed that nothing in the report shall be deemed to relieve any designer,
manufacturer, seller, supplier, repairer or operator of any warranty, expressed or implied, and Dutch Safety & security Consultancies shall be
limited to the acts or omission of its employees, agents and subcontractors. Under no circumstance whatsoever shall and Dutech Safety &
security Consultancies be liable for any injury or damage to any person, or occurring by reason of negligent operation or any defect in materials,
machinery, equipment or other items other than such defects ascertainable by normally accepted testing standards and those items inspected by
Dutech Safety & security Consultancies and which are covered by this certificate.

Page 1 of 2
Doc. No: FM-DT-20-1 REV 06 Dated 19-07-2020

Po: Box: 390500, Al Qusais Ind. Area 2, Dubai, UAE.


Tel: +971 42568979, Email: dutechsafety70@gmail.com.
Test Engineer Report:
Work No: DT-D-20- Certificate No: DT-
EXAMINATION & TEST REPORT OF LIFTING GEAR

CHECKLIST FOR WIRE ROPE SLING


ITEM DESCRIPTION OK FD NA
1 Declaration of conformity (or) previous inspection certificate
2 PPE (Inspector)
3 Identification marking or tag (WLL, EWL, Angle of Sling)
4 Rope grade (1770 or 1960)
5 Formation of eye (ferrule min. 20 times of dia & spliced min 15 times of dia )
6 Terminal fitting (1.6 times of WLL)
Length (ferrule 2 dia or 1% length is whichever greater) (spliced 4 dia or 2% is
7 whichever greater length)
8 Wire rope sling condition (wear 10 % of dia )
9 Broken wire (randomly 6 nos on length 6d & no 14 nos on length 30d )
10 Ferrule tail length (half of diamete )
11 Twisted or Bend (<10˚)
12 Cracks
13 Gouges
14 Corrosion
15 End Fittings
16 Master Link: Stretch or Wear
17 Kink
18 Bird caging
19 Strand or Core protrusion
20 Evidence files (photos, manufacture details, etc.) shall be attached with checklist
OK- SATISFACTORY FD- FINDING NA- NOT APPLICABLE
General Notes/Remarks/Recommendations (If any)

Any reservations or restrictions on the use of Maximum Capacity of the Equipment: NIL
Note: Please rectify the remarks / recommendations given in the above column.

Inspection engineer: Company Seal:


Date:

Page 2 of 2
Doc. No: FM-DT-20-1 REV 06 Dated 19-07-2020

Po: Box: 390500, Al Qusais Ind. Area 2, Dubai, UAE.


Tel: +971 42568979, Email: dutechsafety70@gmail.com.

You might also like