Professional Documents
Culture Documents
BLR-212FF-950 (Ica)
BLR-212FF-950 (Ica)
STC# SR01865SE
THIS DOCUMENT IS PROPRIETARY TO BLR AEROSPACE, LLC AND MAY NOT BE DISCLOSED, COPIED
OR USED FOR DESIGN OR MANUFACTURE, IN WHOLE OR IN PART, WITHOUT DIRECT WRITTEN AUTHORIZATION.
COPYRIGHT © 2007 BLR AEROSPACE, LLC, EVERETT, WASHINGTON, USA, ALL RIGHTS RESERVED.
REVISIONS
BLR-212FF-950 ii
Rev C 03/21/16
LIST OF ACTIVE PAGES
1 C
2 C
3 C
4 C
5 C
6 C
7 C
8 C
9 C
10 C
A.1 IR
BLR-212FF-950 iii
Rev C 03/21/16
TABLE OF CONTENTS
REVISIONS ii
LIST OF ACTIVE PAGES iii
TABLE OF CONTENTS iv
1 INTRODUCTION 1
1.2 CONTACT INFORMATION 1
2 GENERAL DESCRIPTION AND OVERVIEW 2
3 AIRWORTHINESS LIMITATIONS 4
3.1 CG 4
4 INSPECTION AND REPAIR 5
4.1 REQUIRED INSPECTION EVENTS 5
4.2 INSPECTION TECHNIQUES 6
4.3 DAMAGE TYPES 7
4.4 DAMAGE CLASSIFICATION 8
4.5 REPAIR 8
5 COMPONENT OVERHAUL 10
6 PLACARDS AND MARKINGS 10
APPENDIX A A1
BLR-212FF-950 iv
Rev C 03/21/16
1 INTRODUCTION
These Instructions for Continued Airworthiness are prepared in accordance with FAA
order 8110.54, dated July 1, 2005.
Revisions to this ICA will be coordinated with the FAA. BLR will contact owners via
email, phone or standard mail when a revision to this ICA is available.
Our interest in your satisfaction with our products has not ceased with your purchase of
our Dual Tail boom Strakes and FastFin™ modification. Please feel free to contact BLR
Aerospace, LLC at any time.
For all matters concerning the installation, maintenance, inspection and repair of the
Dual Tail boom Strakes and FastFin™ system, contact:
BLR-212FF-950 1
Rev C 03/21/16
2 GENERAL DESCRIPTION AND OVERVIEW
The BLR Dual Tail Boom Strakes and FastFin System is comprised of two graphite
fairings, an aluminum (or carbon fiber) tail stiffener, and aluminum tail boom strakes.
The dual tail boom strakes consist of simple aluminum angles, attached along the
length of the tail boom (as shown in Figure 2.1), from reference datum 250 to 440
(see Figure 2.4 for datum stations).
The BLR FastFin replaces the original vertical fin aluminum trailing edge and aft tail
boom fairing (as shown in Figure 2.2) between datum stations 450 and 490 (see
Figure 2.4) and does not alter the position or function of any existing systems,
including lights. The fairings are constructed of aerospace industry standard graphite
materials. The tail stiffener is made of aerospace grade clad 2024 aluminum (shown
in Figure 2.3).
The BLR Dual Tail Boom Strakes and FastFin System is a static structural
modification; therefore, there are no additional moving parts to control, operate or
service.
Figure 2.1 BLR Dual Tail Boom Strakes System Installed on the Bell 212 Series Helicopter
Figure 2.2 BLR Fast Fin System Installation Shown with Unmodified U.S. Army UH-1H
Vertical Tail Fin on the U.S. Army UH-1H Series Helicopter
BLR-212FF-950 2
Rev C 03/21/16
205-D-1002-1/-2
Aft Spar Stiffener
OR
205-D-1003-1/-2
Carbon Fiber Stiffener
Figure 2.3 BLR Fast Fin Tail Stiffener Installed on the Vertical Tail Fin of a
Bell 212 Helicopter
BLR-212FF-950 3
Rev C 03/21/16
3 AIRWORTHINESS LIMITATIONS
3.1 CG
BLR Dual Tail Boom Strakes (DTBS) and FastFin System kit adds to the empty weight
of the helicopter when installed. (Data is also supplied for revising the weight and
balance when retrofitting with a partial system. For example, tail boom strakes were
previously installed and CG revised; data is supplied for the addition of the FastFin.)
Revise the rotorcraft list, weight and balance using the following data:
BLR-212FF-950 4
Rev C 03/21/16
4 INSPECTION AND REPAIR
4.1.1 Annual
Inspect all exterior skins, upstanding legs, and fairing trailing edges for visible damage.
Inspect all attach points for cracks, loose attaching hardware and distortion. (Inspection
Techniques 4.2.1 - 4.2.3)
4.1.2 Progressive
Inspect all exterior skins, upstanding legs, and fairing trailing edges for visible damage.
Inspect all attach points for cracks, loose attaching hardware and distortion. (Inspection
Techniques 4.2.1 - 4.2.3)
4.1.3 Preflight
The BLR Dual Tail Boom Strakes and FastFin System should be inspected in the course
of a typical preflight inspection, with the same inspection rigor applicable to the original
aircraft component. Any damage should be noted, such as; paint chips, scratches,
gouges, wrinkles, etc. Presence of any external damage is an indication of potential
internal damage.
Inspect all exterior skins, upstanding legs, and fairing trailing edges for visible damage.
Inspect all attach points for cracks, loose attaching hardware and distortion. (Inspection
Techniques 4.2.1, 4.2.2.)
If the aircraft has been subjected to abnormal flight loading conditions (turbulent
weather, harsh maneuvers etc.), a post flight inspection should be conducted to
determine if any damage occurred. Abnormal flight damage usually results in skins
indentations or cracks, deformed upstanding legs, loose rivets, etc.
Inspect all exterior skins, upstanding legs, and fairing trailing edges for visible damage.
Inspect all attach points for cracks, loose attaching hardware and distortion. (Inspection
Technique 4.2.1, 4.2.2.)
BLR-212FF-950 5
Rev C 03/21/16
4.1.5 Abnormal Ground or Ground Handling Loads
If the aircraft has been subjected to abnormal ground loading/handling conditions (hard
landing, abuse loads imposed during fueling or servicing, mooring/wind damage,
temperature extremes), an inspection should be conducted to determine if any damage
occurred to the aircraft. Ground handling load damage usually results in more local
damage such as; dents, paint chips, scratches, gouges, wrinkles, etc.
Inspect all exterior skins, upstanding legs, and fairing trailing edges for visible damage.
Inspect all attach points for cracks, loose attaching hardware and distortion. (Inspection
Technique 4.2.1, 4.2.2.)
When the aircraft is subjected to specific and known and identifiable loading or event,
(such as bird strike, lightning strike, gravel impact, hangar or stationary object collision
and tool impact loads) it is referred to as “DSD” or Discrete Source Damage. An
inspection, as soon as practical, is required. DSD usually manifests itself in the form of
damage to the fairing skin, deformed upstanding legs, sheared fasteners, cracks, holes,
missing pieces, etc.
Inspect all exterior skins, upstanding legs, and fairing trailing edges for visible damage.
Inspect all attach points for cracks, loose attaching hardware and distortion. (Inspection
Technique 4.2.1, 4.2.2.)
This method is employed as the primary means to identify indications of further damage.
A magnifying glass may be used to supplement the inspection. It should be noted that,
in general, composite structure does not “dent” in the same manner aluminum does,
given the same impact conditions. Composite structure is very resilient on the surface
and can mask greater internal damage. Chipped paint or scratched surfaces are
indications that should be investigated further by other means. (4.2.2, 4.2.3.)
Inspect Dual Tail Boom Strakes for damage, deformation and security of attachment.
Inspect sealant for voids and deterioration.
This method is used as a means of detecting damage that can be missed with the visual
method due to lighting conditions, glare, paint color or patterns, etc. The hand and
fingers are remarkably sensitive to contour and texture changes which can be indicative
of additional damage. A combination of tactile and auditory inspections can be used by
BLR-212FF-950 6
Rev C 03/21/16
applying hand pressure to the structure, and listening for unusual noises like “snapping”,
“crackling” or “popping”, which indicates internal damage.
Tap testing may be used to evaluate the condition of composite laminated and bonded
structures using the auditory sense. Surfaces to be inspected must be dry and have all
oil or grease removed. This inspection must be conducted in a relatively quiet area. The
method consists of lightly tapping the surface of the part with a tap hammer, and
comparing the acoustic response with the response of a “known” damage free area.
The tapping rate is adjusted to produce a nearly continuous sound response so that any
difference in sound tone can be detected. A “flat” or “dead” response indicates an area
of internal damage in the form of, but not limited to, delamination or dis-bond. The
acoustic response of a good part can vary dramatically with changes in geometry. The
entire area of interest must be tapped. The method is limited to finding relatively shallow
defects in the graphite laminate and possibly the bond line between the laminate and
core.
The following definitions reflect the possible types and causes of damage to the BLR
Dual Tail Boom Strakes and FastFin System Modification.
Impact damage occurs when the Strakes or FastFin strikes or is struck by some object
(4.1.6). This type of damage may happen to an aircraft at any time. All detected impact
damage must be inspected for structural damage. Inspect per inspection techniques
4.2.1 - 4.2.3, as required.
Lightning strike damage may vary in intensity, location, and type. Lightning damage can
require the replacement of the component, due to the typical extent of the damage.
(4.1.6) Inspect per inspection techniques 4.2.1 - 4.2.3, as required.
Cosmetic and structural damage to the strakes may be repaired per sections 4.5.4 and
4.5.5.
Damage to the composite fairing is structurally complicated and may not be assessed in
the field. Contact BLR for a replacement fairing.
BLR-212FF-950 7
Rev C 03/21/16
4.3.3 Thermal Damage - Fairing
Thermal or burn damage occurs when the fairing composite materials are exposed to
extreme temperatures. The most critical is an elevated temperature, because composite
structure can be permanently damaged by excessive heat. Thermal damage is apparent
by discoloration or oxidation of the normal surface appearance (paint color and texture).
Damage classification, as outlined in this structural repair manual, may range from
superficial surface damage to permanent distortion. Any damage identified on the
aluminum strake portion of the BLR Dual Tail Boom Strakes and FastFin System
Modification should be addressed and repaired in accordance with sections 4.5.4 and
4.5.5 below. If part replacement is required, contact BLR Aerospace.
The composite tail fairing portion of the BLR Dual Tail Boom Strakes and FastFin
System Modification was designed as a robust assembly capable of maintaining its
structural integrity, even in the event of some type and degree of damage. It has been
structurally tested with the intentional inclusion of damage, to prove the structural
capability thereafter. However, assessing damage requires structural analysis of the
part, which may not be done in the field. Any damage beyond that deemed ‘cosmetic’
(4.4.1) requires a replacement fairing from BLR.
Damage of this type is superficial and has no restrictions on flight operations. It can be
permitted to exist “as is” or to be cosmetically repaired by nonstructural means. (See
section 4.5.1 for fairing cosmetic damage definition and repair.)
Damage of this type requires structural analysis. Contact BLR for replacement of
damaged parts.
4.5 REPAIR
The repair classifications mirror the damage classifications. The extent and location of
the damage determines its classification. The evaluation of the classification is
conducted by the engineering department at BLR Aerospace. Digital imaging and
photographs are two means of providing the required data to BLR for evaluation.
BLR-212FF-950 8
Rev C 03/21/16
4.5.1 Cosmetic Repair - Fairing
Cosmetic repairs may be done in the field. Cosmetically repaired damage must be
limited to small surface damage in the form of scratches or nicks. They may be
cosmetically repaired using aerospace grade filler and paint touch-up.
Contact a BLR representative for evaluation and/or repair instruction assistance.
Due to the high level of analysis required to assess structural damage to the composite
fairing, repair (beyond cosmetic) is not allowed. Please contact BLR for a replacement
fairing.
BLR does not recommend removal of the tail fairing and stiffener. If removal is required,
please contact BLR for guidance.
Cosmetic repairs may be done in the field. Cosmetically repaired damage must be
limited to small surface damage in the form of scratches, nicks, etc. that may be repaired
by sanding and repainting. Small sealant voids at edge of strake may be corrected using
touch-up aerospace grade sealant per MIL-S-8802.
Structural repair of the dual tail boom strakes is not allowed. Contact BLR for
replacement parts.
1. Carefully drill out rivet heads and punch out center stems.
2. Using solvent, separate the strakes from the tail boom, using caution to prevent
bending strakes or denting tail boom skin. Retain small nylon spacers and
aluminum washers for reinstallation. NOTE: If hardware is damaged or missing,
contact BLR for replacement parts.
3. Clean the sealant off the length of the tail boom.
Before reinstallation, inspect strakes carefully for damage. If required, contact BLR for
replacement parts and/or current installation instructions.
BLR-212FF-950 9
Rev C 03/21/16
Reinstall strakes:
1. Align holes in strakes with attachment holes in tail boom and temporarily secure
with clecos. Ensure there is a .03” setback from the skin lap at the fuselage and
the forward end of the first strake. CAUTION: A .050-.070” gap between
strakes is MANDATORY to allow for tail boom flexing. Strakes may be
trimmed to allow for gap.
2. Place masking tape 1/8” from periphery of strakes to aid in sealant clean-up.
3. Remove strakes and prepare mounting surfaces for installation by scuffing and
cleaning with solvent.
4. Apply MIL-S-8802 sealant to tail boom and strake mounting surfaces.
5. Prepare rivets with washers and spacers on the stems.
6. Attach strakes using CR3213-5 rivets and retained washers wet with MIL-S-8802
sealant. (For lower attachment holes forward of boom station 101.38, fill
underlying composite honeycomb cells thoroughly before installing rivets.) Keep
the spacer centered in the strake hole during attachment.
7. Remove masking tape and clean up sealant fillet as required.
5 COMPONENT OVERHAUL
A ‘No Push’ decal is applied to the upper aft end of the lower fairing, as shown in Figure
6.1. If the placard is missing, please contact BLR for a replacement. (An aviation grade
placard of similar size and shape may be substituted, where required.)
Figure 6.1 ‘No Push’ Placard applied to the Lower Tail Fairing of BLR FastFin System
BLR-212FF-950 10
Rev C 03/21/16
APPENDIX A
Inspection is required every 12 calendar months, every 100 flight hours, preflight (use this form to
document damage only), after experiencing abnormal flight loads or discrete source damage.
Parts to be inspected: Strake, P/N (or position); FastFin, P/N (or position)
Inspection Type: Annual, Progressive, Event Driven (abnormal loading, damage, etc.)
Inspection Pass/
Date Part Inspector Findings
Type Fail
Damage to composite part (photos and
Upper Tail
Example Progressive JHD F summary attached). Contacted BLR for
Fin
replacement part.
BLR-212FF-950 A.1
Rev IR 12/20/07