Professional Documents
Culture Documents
Eastron SDM630MCT-RJ User-Manual 2020
Eastron SDM630MCT-RJ User-Manual 2020
3 Parity
Each successive press of the U/I
ESC
button selects a new parameter:
Total reactive energy in
kVArh. Use the and
buttons to select the menu
option. The screen will show
Phase to neutral voltages.
User Manual
2020
Please note the register is 9999999.9 display over two lines.
the current setting.
4 Set Up
SDM630MCT-RJ Hold the button to
enter the menu option, the
To enter set up mode, hold the button for 3 seconds, until the
DIN Rail Smart Energy Meter for Single and Three Phase to Phase voltages.
password screen appears.
current selection will flash.
Phase Electrical Systems
The set up is password-
1 Introduction protected so you must Use the and
enter the correct password buttons to select the
This document provides operating, maintenance and installation (default ‘1000’) before required option.
instructions. This unit measures and displays the characteristics of Current on each phase. processing. Range: None (default), Odd
Single Phase Two Wire (1P2W) and Three Phase Four Wire (3P4W) or Even.
networks. The measuring parameters include Voltage (V), Current
(A), Frequency (Hz), Power (kW/KVA/KVAr), Power Factor (PF), On completion of the entry procedure, hold the button for 3
Imported, Exported and Total Energy (kWh/kVArh). The unit also If an incorrect password seconds until the selection stops flashing.
measures Maximum Demand Current and Power, this is measured is entered, the display will
over preset periods of up to 60 minutes. Phase to neutral voltage show:
THD%. 4.2.4 Stop bits
This particular model accommodates 100mA Current Transformers PASS Err (Error)
and can be configured to work with a wide range of CTs. It also
comes with a complete comms capability with built in RS485
To exit the set up menu, hold the U/I for 3 seconds, the
Modbus RTU outputs, configuration is password protected. Use the and
ESC
• System Configuration - 1P2W & 3P4W. 6. On completion of all setting-up, hold the U/I button for 3
4.5 CT Configuration
ESC
seconds, the measurement screen will then be restored. This unit is CT Operated, the primary (CT1) and secondary (CT2) of
• Demand Interval Time
the current transformer need to be programmed correctly for the
• Reset for Demand Measurements meter to scale the inputs accordingly.
Maximum Power Demand. 4.1.2 Number Entry Procedure
1.2 Current Transformer Primary Current When setting up the unit, some screens require the entering Use the and
%
of a number. In particular, on entry to the setting up section, a buttons to select the menu
This unit requires configuring to operate with the appropriate
password must be entered. Digits are set individually, from left to option. The screen will show
curren transformer(s), thesecondary current is 0.1A. It is %
right. The procedure is as follows: the configure CT setting.
programmed by inputting the ratio (CT Primary). It can be used on
primary currents up to 6000A. Maximum Current 1. The current digit to be set flashes and then can be adjusted using %
Demand. the and buttons.
Secondary CT (CT2):
2. Press the button to more right to the next digit. % Hold the button to set
the CT secondary option:
3. After setting the last digit, hold the button for 3 seconds to
1.3 RS485 Serial – Modbus RTU save your selection. % 0.1A.(Not Configurable)
This unit is compatible with remote monitoring through RS485 3.3 Power %
Modbus RTU. Set-up screens are provided for configuring the 4.2 Communication
RS485 port. Refers to section 4.8. Each successive press of the button select a new range: Set the CT Ratio Value:
The RS485 port can be used for communication using Modbus RTU Hold the button to
%
Protocol. To configure the Modbus settings, such as Address and enter the CT Ratio setting
Baud Rate, this is also done within the Password-protected set up screen. The range is from
%
Instantaneous Active menu. 0001 to 9999. 0005A default
2 Start Up Screens Power in kW. %
Hold the button for 3 seconds to exit the set up menu Parity: none (default) / odd / even
Stop bits: 1 or 2
Hold the button to RS485 Network Address: 3 digit number - 001-247
confirm the selection. 4.13 System Phase Sequence
Modbus™ Word order Hi/Lo byte order is set automatically to
The system sequence option sets the phase sequence with the
voltage V1,V2 & V3 of the meter
normal or reverse. It cannot be configured from the Option 2
set-up menu.
Hold the U/IESC
button for 3 seconds to exit the set up menu.
Use the and Requires phase sequence, change L3 to L1 and L1 to L3, please
buttons to select the menu 5.6 Reference Conditions of Influence refer to section 4.13
4.8 Set backlight Display option. The screen will show Quantities
the phase voltage sequence
The meter provides a function to set how long you want the display
setting. Influence Quantities are variables that affect measurement
screen back light to be active
errors to a minor degree. Accuracy is verified under nominal
value (within the specified tolerance) of these conditions.
Use the and Voltage Setting:
buttons to select the menu Hold the button to • Ambient temperature 23°C ±1°C
option. The screen will show set the voltage option: V1,
the current setting deafult 0 • Input waveform 50 or 60Hz ±2%
V2 & V3
meaning it is on indefinitely. • Input waveform Sinusoidal (distortion
Option: 0, 5, 10, 30, 60 &120. factor < 0·005)
Set the Voltage for each • Auxiliary supply voltage Nominal ±1%
Hold the button to confirm the setting and press U/I ESC
to phase:
return to the main set up menu. Hold the button to • Auxiliary supply frequency Nominal ±1%
enter the phase sequence • Auxiliary supply waveform (if AC) Sinusoidal (distortion
screen. Option :CT1, CT2 factor < 0·05)
& CT3.
• Magnetic field of external origin Terrestrial flux
4.9 Supply System
The unit has a default setting of 3 Phase 4 Wire (3P4W).
Use this section to set the type of electrical system. 5 Specifications 5.7 Environment
• Operating temperature -25°C to +55°C*
Use the and 5.1 Measured Parameters
• Storage temperature -40°C to +70°C*
buttons to select the menu The unit can monitor and display the following parameters of
option. The screen will a Single Phase Two Wire (1P2W) or Three Phase Four Wire • Relative humidity 0 to 95%,
show the current setting. non-condensing Option 3
(3P4W) system.
• Altitude Up to 3000m
5.1.1 Voltage and Current • Warm up time 1 minute
• Vibration 10Hz to 50Hz, IEC Requires flow reversal , please refer to section 4.12
Hold the button to • Phase to Neutral Voltages 100-289V AC
enter the menu option, the (not for 3P3W supplies). 60068-2-6, 2g
current selection will flash. • Phase to Phase Voltages 173-500V AC • Shock 30g in 3 planes
(3 Phase supplies only).
• Percentage Total Voltage Harmonic Distortion (V %THD) for *Maximum operating and storage temperatures are in the
each Phase to Neutral (not for 3P3W supplies). context of typical daily and seasonal variation.
Use the and • Percentage Total Voltage Harmonic Distortion (V% THD)
buttons to select the between Phases (3 Phase supplies only).
required option.
5.8 Mechanics
• Current %THD for each Phase.
• DIN rail dimensions 72 x 94.5 mm (WxH)
per DIN 43880
Hold the button to confirm your adjustment. Hold the U/I ESC
5.1.2 Power factor and Frequency and
button for 3 seconds to exit the set up menu. • Mounting DIN rail (DIN 43880)
Max. Demand
• Sealing IP51 indoor
4.10 CLR
• Frequency in Hz • Material Self-extinguishing UL
The meter provides a function to reset the maximum demand • Instantaneous power: 94 V-0
value of current and power.
• Power 0-3600 MW