Professional Documents
Culture Documents
ATS SPECIFICATION Imex
ATS SPECIFICATION Imex
rated for full load, continuous operation. numbers of poles (3 pole and neutral)
• To transition between 3 sources – 1 Utility and 2
Generators
• Industrial Grade
• 4 Pole (3 Phase + Neutral)
• 400V /50Hz Service voltage.
4. Multi – voltage The transfer switch shall be supplied with COMPLY
compatibility (single multi-voltage capability to allow use on a SCHNEIDER ASCO ATS has been manufactured to operate with
phase and three phase variety of standard system voltage levels different voltage capabilities such as 240V, 380V, 480V, 600V.
system) without replacement of components. The
transfer switch shall be field configurable to
operate on the following nominal system
voltages; 240V, 380V, 480V, 600V.
6.3 Load test capability When an On-Load test mode is activated, the COMPLY
ATS shall automatically transfer the emergency SCHNEIDER ASCO ATS has been manufactured to operate with
load to the generator supply and return the load on load test capabilities on the generator so that it enables the
to the utility supply upon test completion. generator to test load caring capacity with the mains presence.
6.4 Transfer capability The ATS shall perform a closed transition fast COMPLY
from genset to mains power transfer between operating generator SCHNEIDER ASCO ATS has been manufactured to operate to
and the utility supply once the utility power have a fast power transfer time to go from generator to the mains
source has been restored. when the mains source is restored.
6.5 ATS components The Automatic Transfer Switch package shall COMPLY
include the following main components: SCHNEIDER ASCO ATS has been manufactured to operate with
A. ATS Enclosure the components listed below
B. Power Switching Mechanism • ATS Enclosure
C. Automatic Transfer Switch Controller: • Power Switching Mechanism
D. Operator Interface Display • Automatic Transfer Switch Controller:
E. Source Voltage & Frequency Sensors • Operator Interface Display
F. ATS control logic c/w Integrated Time • Source Voltage & Frequency Sensors
Delays, Inputs & Outputs
• ATS control logic c/w Integrated Time Delays, Inputs &
G. Engine Start Output Contact
Outputs
• Engine Start Output Contact
7. Experience The Transfer Switch shall be designed and COMPLY
manufactured in a facility, which is registered to SCHNEIDER ASCO ATS has been manufactured to operate with
an ISO 9001:2008 quality system. The supplier quality system of ISO 9001:2008 registered and the company has
shall have a minimum of 10 years’ experience over 10 years of experience on this field.
designing and manufacturing automatic
transfer switches.
8. Weather condition The Transfer Switch should operate COMPLY
compatibility continuously in Addis Ababa and entoto altitude SCHNEIDER ASCO ATS has been manufactured to operate to
and weather condition. withstand harsh weather conditions and then will operate In
Addis Ababa and entoto altitude and weather conditions.
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
9. Capability of load with The automatic transfer switch assembly shall be COMPLY
our derating rated for 100% continuous load without de- SCHNEIDER ASCO ATS has been manufactured to work 100%
rating. continuous load without de rating.
10. Short circuit fault Short Circuit fault withstand current rating of COMPLY
current rating the complete assembly shall be 50 K amps RMS SCHNEIDER ASCO ATS has been manufactured to operate with
for up to 3 Cycles. The interrupting and closing short circuit fault withstand current rating of 36KA.
rating shall be equal to or exceed the required
withstand rating. This rating shall be obtained
with standard upstream over current protection
devices.
11. Enclosure The complete ATS assembly shall be mounted COMPLY
in a NEMA 3R rated enclosure suitable for SCHNEIDER ASCO ATS has been manufactured to operate with
outdoor application. NEMA 3R rated enclosure and it is suitable for outdoor
application.
12. Accessibility of ports The rear section shall contain bussing and COMPLY
provisions for customer incoming and outgoing SCHNEIDER ASCO ATS has been manufactured to operate with
line and load cables. Access shall be from the rear section which has bussing and provisions for cable
rear by removable rear covers. incomings and outgoing line and load cables.
13. Lugs Adequate size and quantity of ground lugs shall COMPLY
be provided and shall conform to NEC/CEC SCHNEIDER ASCO ATS has been manufactured to operate with
guidelines. Ground bus shall be a full-length adequate size and quantity of ground lugs will be provided and
copper ground bus bonded to the frame with which are conform to NEC/CEC.
adequate size and quantity of ground lugs and
shall conform to NEC/CEC guidelines.
14. Busbars Where load bus bars are utilized, they shall be COMPLY
tin plated round-edge high conductivity copper SCHNEIDER ASCO ATS has been manufactured to operate with
and be sized for 100% continuous load rating of load bus bars that are utilized and it is tin plated rounded-edge
the transfer switch, in accordance with NEMA, high conductive and which is sized for 100% continuous load
CSA and UL guidelines. The short circuit rating and also works in accordance of NEMA, CSA and UL
withstand rating of the completed bus assembly guidelines.
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
17. Power switching unit The power switching units shall be fix- COMPLY
mounted, utilize fully enclosed contacts and SCHNEIDER ASCO ATS has been manufactured to operate with
their withstand/closing rating shall be equal to power switching units which is fix-mounted, utilize fully enclosed
or exceed the required withstand rating of the contacts.
complete system.
18. Brand new materials All materials and parts used in the unit COMPLY
shall be new, of current manufacture, of best SCHNEIDER ASCO ATS has been manufactured to operate with
industrial grade, and free from defects and brand new materials which are free from defects and
imperfections. imperfections.
21. Strength and rigidity The enclosure shall consist of a 16 gauge or COMPLY
better steel angle /channel framework and be of SCHNEIDER ASCO ATS has been manufactured to operate with
adequate strength and rigidity to endure enclosure consist of 16 gauge and has adequate strength and
normal conditions of use and to support all rigidity.
equipment mounted within. Bolt-on steel
panels and hinged doors shall form the outer
shell of the enclosure.
22. Seismic events The Transfer Switch shall be designed and COMPLIANT
withstanding constructed to withstand seismic events when SCHNEIDER ASCO ATS has been manufactured to operate with
capability in building correctly anchored to the building structure. to withstand seismic events when correctly anchored to the
structure building structure.
25. PLC module The automatic transfer switch shall include a COMPLY
fully integrated microprocessor-based Transfer SCHNEIDER ASCO ATS has been manufactured to operate with
Switch Controller which shall provide the PLC module which will include a fully integrated microprocessor
following key features: – based transfer switch controller which will provide the
A. Graphical 7" Color Touch Screen Operator following key features
Interface Display A. Graphical 7" Color Touch Screen Operator Interface Display
B. Open and/or Closed Transition Transfer B. Open and/or Closed Transition Transfer Control
Control C. Utility/Gen Voltage and Frequency Metering
C. Utility/Gen Voltage and Frequency Metering D. Modbus TM RTU Serial Communication
D. Modbus TM RTU Serial Communication E. 8 Programmable Relay Output Contacts/more
E. 8 Programmable Relay Output F. 16 Programmable Digital Inputs/more
Contacts/more G. Engine Start Output Contact
F. 16 Programmable Digital Inputs/more
G. Engine Start Output Contact
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
readings. The following standard metering B. Three phase or single-phase voltages (Line to Line & Line to
features shall be provided for the utility and Neutral).
generator supplies; C. Phaser diagram showing graphical phase relationship
A. Digital and graphical analog display of AC and voltage magnitude.
voltages. D. Symmetrical Component Diagrams (Positive, Negative &
B. Three phase or single-phase voltages (Line Zero sequence display).
to Line & Line to Neutral). E. Voltage phase rotation indication.
C. Phaser diagram showing graphical F. Frequency display to 0.1 Hz resolution.
phase relationship and voltage magnitude.
D. Symmetrical Component Diagrams
(Positive, Negative & Zero sequence display).
E. Voltage phase rotation indication.
F. Frequency display to 0.1 Hz resolution.
26.
26.1 Voltage and frequency
sensing The Transfer Switch controller shall have fully COMPLY
integrated 220-600V, 3 phase true RMS AC SCHNEIDER ASCO ATS
voltage sensing on the Utility Supply, generator has been manufactured to operate with fully integrated 220V-
supply and ATS Load bus for operation and 600V three phase true RMS AC voltage sensing on the utility
monitoring. Programmable set points shall be supply, generator supply and ATS load bus for operation and
provided for utility/generator source under monitoring.
voltage, overvoltage and phase unbalance.
AC voltage sensing shall utilize advanced COMPLY
symmetrical component algorithms to SCHNEIDER ASCO ATS
determine positive, negative and zero sequence has been manufactured to operate with AC voltage sensing with
voltages. This shall provide the capability to utilize advance symmetrical component algorithms to determine
detect true phase loss/unbalance (i.e. single positive, negative and zero sequence voltages, this will provide
phasing) protection on 3 phase systems where the capability to detect true phase loss/unbalance (i.e. single
re-generative phase voltages maybe present phasing) protection on 3 phase systems where re-generative
due to failed 3 phase transformers or motor phase voltages maybe present due to failed 3 phase transformers
loads. or motor loads.
AC Voltage sensing shall be fully configurable to COMPLY
allow operation on 3 phase 3 wire and 3 phase SCHNEIDER ASCO ATS
4 wire systems without use of additional has been manufactured to operate with AC Voltage sensing which
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
potential transformers on systems 60OVAC or is fully configurable to allow operation on 3 phase 3 wire and 3
below. phase 4 wire systems without use of additional potential
transformers on systems 60OVAC or below.
source or shall inhibit a transfer to a source 100-130% of nominal and is based on a rising (i.e. pick-up)
until its voltage levels are within normal voltage. The over voltage sensor is factory set for pick-up at 115%
limits. The over voltage sensor shall be user nominal voltage. The over voltage sensor is reset (i.e. drop-out)
adjustable from 100-130% of nominal and shall 5% below the pick-up setting and is user adjustable. The over
be based on a rising (i.e. pick-up) voltage. The voltage sensor includes an adjustable transient time delay
over voltage sensor shall be factory set for pick- feature.
up at 115% nominal voltage. The over voltage
sensor shall reset (i.e. drop-out) 5% below the
pick-up setting and shall be adjustable. The
over voltage sensor shall include an adjustable
transient time delay feature.
Phase Unbalance/Phase Loss Sensing: COMPLY
Voltage phase unbalance/phase loss sensing SCHNEIDER ASCO ATS
shall be provided for the generator and utility has been manufactured to operate with phase loss sensing or
supplies. Activation of an abnormal utility phase unbalance sensing, this will enable the generator to turn off
phase unbalance condition shall initiate the when the generator it senses phase unbalance or phase loss.
generator to start and to transfer on load. The The voltage phase unbalance sensor is user adjustable from 3-
voltage phase unbalance sensor shall be user 30% of nominal and is factory set for pick-up at 5% nominal
adjustable from 3-30% of nominal and shall be voltage. The voltage phase unbalance sensor includes an
factory set for pick-up at 5% nominal voltage. adjustable transient time delay feature.
The voltage phase unbalance sensor shall
include an adjustable transient time delay
feature.
Under Frequency Sensing: Under frequency COMPLIANT
sensing shall be provided for both utility and SCHNEIDER ASCO ATS
generator supplies. Activation of an abnormal has been manufactured to operate with under frequency sensing
under frequency condition shall initiate a load which will provide for both utility and generator supplies.
transfer to the alternate source or shall inhibit The under frequency sensor is user adjustable from 70-100% of
a transfer to a source until its frequency nominal and is based on a falling {i.e. drop-out) frequency. The
levels are within normal limits. The under under frequency sensor is factory set for drop out at 80%
frequency sensor shall be user adjustable from nominal frequency. The under frequency sensor is reset {i.e.
70-100% of nominal and shall be based on a pick-up) 10% above the dropout setting and is adjustable. The
falling {i.e. drop-out) frequency. The under under-frequency sensor includes an adjustable transient time
frequency sensor shall be factory set for delay feature.
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
limits. The time delay shall be user adjustable 0- 0-60 minutes, factory set at two (2) seconds.
60 minutes, factory set at two (2) seconds.
Utility Return - A time delay for return to COMPLY
utility shall be provided which permits a re- SCHNEIDER ASCO ATS
transfer back to the utility supply only after has been manufactured to operate with utility return time delay
stable voltage and frequency condition exists with user adjustable, The time delay is to be user adjustable 0-60
for the specified time period. The time delay minutes, factory set at two (2) minutes.
shall be user adjustable 0-60 minutes, factory
set at two (2) minutes.
Engine Cooldown - A time delay for engine COMPLY
cooldown shall be provided which delays the SCHNEIDER ASCO ATS
engine stop signal after load has retransferred has been manufactured to operate with engine cooldown delay
back to the utility source. The time delay shall time with user adjustable, The time delay is user adjustable 0- 60
be user adjustable 0- 60 minutes, factory set at minutes, factory set at two (2) minutes.
two (2) minutes.
Neutral Delay - A time delay for neutral COMPLY
position shall be provided in the open SCHNEIDER ASCO ATS
transition mode to minimize the effect of out-of- has been manufactured to operate with neutral delay time with
phase transfer due to connected motor load. user adjustable time frame, The time delay is user adjustable 0-
The time delay shall be user adjustable 0- 120 120 seconds, factory set at three (3) seconds.
seconds, factory set at three (3) seconds.
Gen Commit to Transfer Delay - A time delay COMPLIANT
for Gen Commit to Transfer position shall be SCHNEIDER ASCO ATS
provided. Should the generator fail to transfer has been manufactured to operate with gen commit time delay
on load with the "commit to transfer" feature with transfer position to be provided, The time delay is user
enabled, the ATS shall automatically re-transfer adjustable 0-600 seconds, factory set at three hundred (300)
back to the utility supply if within nominal seconds.
limits following expirary of the "Gen Commit
to Transfer" timer. The time delay shall be
user adjustable 0-600 seconds, factory set at
three hundred (300) seconds.
Transfer Fail Delay - A time delay for Transfer COMPLY
Fail delay shall be provided. SCHNEIDER ASCO ATS
has been manufactured to operate with transfer fail delay with
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
The timer shall activate a fail alarm condition if user adjustable time frame, The time delay is user adjustable 0-
the transfer switch fails to successfully transfer 600 seconds, factory set at thirty (30) seconds.
within the transfer fail time delay setting. The
time delay shall be user adjustable 0- 600
seconds, factory set at thirty (30) seconds.
28
29. Timer Bypass: The transfer controller shall provide a timer COMPLY
bypass function to automatically bypass SCHNEIDER ASCO ATS
unwanted delays during testing or maintenance has been manufactured to operate with a timer bypass function to
procedures. The timers shall automatically reset automatically bypass unwanted delays during testing or
on the next operation sequence to their original maintenance procedures, and the time delays will have a user-
setting. The following time delays shall have a initiated bypass features-
user-initiated bypass feature: A. Engine Warmup Delay
A. Engine Warmup Delay B. Utility Return Timer
B. Utility Return Timer C. Engine Cooldown Timer
C. Engine Cooldown Timer D. Neutral Delay Timer
D. Neutral Delay Timer
30. Real time clock The transfer controller shall provide a real-time COMPLIANT
clock to display system time and date for use by SCHNEIDER ASCO ATS
event logging and the ATS exercise scheduler. has been manufactured to operate with real time clock to display
The real-time clock shall have automatic system time and date for use by event logging and the ATS
shifting of date/time for daylight savings and exercise scheduler
leap year occurrences. The real-time time clock
shall be powered by an independent 10 year life
battery to maintain all time/date settings upon
loss of control power.
31. ATS Status The transfer switch controller shall provide the COMPLY
Indication: following indication lights/icons on a common SCHNEIDER ASCO ATS
screen for simple visual indication of ATS has been manufactured to operate with ATS status indication
status: which will provide the following indication screen for simple
A. Utility/Gen Source available visual indication of the ATS status
B. Load Bus Energized A. Utility/Gen Source available
C. ATS Position: Utility or Generator Source B. Load Bus Energized
Connected to Load C. ATS Position: Utility or Generator Source Connected to Load
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
schedules to be added. Each event can be edited the scheduler allows the following programming functionalities.
individually and its operating status can be A. Schedule Event Start Date/Time
monitored. The scheduler shall allow the B. Event Period (Day/Week/Month/Year)
following programming functionality: C. Schedule Event Stop Date/Time
A. Schedule Event Start Date/Time D. Event Duration (mins/hours)
B. Event Period (Day/Week/Month/Year) E. Event Operation Type (Off-Load Test, On-Load Test)
C. Schedule Event Stop Date/Time F. Number of Re-occurring Events (one-time or number of
D. Event Duration (mins/hours) events)
E. Event Operation Type (Off-Load Test, On-
Load Test)
F. Number of Re-occurring Events (one-time or
number of events)
39. Transfer Switch Fail The following transfer switch failure logic and COMPLY
Logic: alarming shall be provided during open or SCHNEIDER ASCO ATS
closed transition transfer sequences has been manufactured to operate with the transfer switch fail
A. Transfer Fail: Control logic shall be provided logic and alarms to be provided during open or closed transition
for sensing a transfer switch failure in open or transfer sequences.
closed transition mode. When an alarm A. Transfer Fail: Control logic to be provided for sensing a
condition is activated, the transfer controller transfer switch failure in open or closed transition mode. When
shall automatically force a transfer to the an alarm condition is activated, the transfer controller will
alternate source if available. automatically force a transfer to the alternate source if available.
B. Power Switching Device Fail: Control B. Power Switching Device Fail: Control logic to be provided to
logic shall be provided to detect if a power detect if a power switching device fails to close or open during
switching device fails to close or open during an open or closed transition operating sequence. and a power
an open or closed transition operating switching device fail to close or open for any reason within a
sequence. Should a power switching device fail preset time period (adjustable), an alarm light and alarm relay
to close or open for any reason within a preset contact will then be activated.
time period (adjustable), an alarm light and C. Gen Failure: Control logic shall be provided for immediate
alarm relay contact shall be activated. transfer to the utility supply (if within acceptable limits)
C. Gen Failure: Control logic shall be provided should the generator set fail during any activated test mode.
for immediate transfer to the utility supply (if
within acceptable limits) should the
generator set fail during any activated test
mode.
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
assignment of one of the programmable output has been manufactured to operate with load shed output contact
contacts. The Load shed output shall be via assignment of one of the programmable output contacts.
activated whenever the generator transfers on And the load shed output will then be activated whenever the
load and shall reset once the utility supply generator transfers on load and will reset once the mains back on
retransfers back on load. the Load shed feature load.
shall be programmable based on a generator And the load shed feature is programmable based on a generator
kW load set point. KW load set point.
44. User Programmable a minimum of Sixteen (16) user programmable COMPLY
Digital Inputs: digital inputs shall be provided by the transfer SCHNEIDER ASCO ATS
controller. The digital inputs shall accept a dry has been manufactured to operate with user programmable
(isolated) logic contact to switch to DC digital inputs. With a minimum of Sixteen (16) user
negative(ground). Each input shall allow programmable digital inputs that will be provided by the transfer
mapping to over 30 different control or controller.
monitoring functions as available within the The digital input will accept a dry (isolated) logic contact to
transfer controller database. The following switch to DC negative(ground), each input allow mapping to over
inputs shall be mapped as factory defaults: 30 different controller or monitoring functions.
A. Remote Test - Utility Power Fail Simulate And the following inputs will be mapped as factory defaults
(Close to Test) A. Remote Test - Utility Power Fail Simulate (Close to Test)
B. Remote Alarm Reset (Momentary Close to B. Remote Alarm Reset (Momentary Close to Reset)
Reset) C. Service Disconnect Mode Activated (External Control Switch)
C. Service Disconnect Mode Activated (External D. Utility Power Switching Device (USD) Tripped
Control Switch) E. Generator Power Switching Device (GSD) Tripped
D. Utility Power Switching Device (USD) F. Transfer Control in Manual (External Control Switch)
Tripped G. Transfer Control in Closed Transition Mode (External Control
E. Generator Power Switching Device (GSD) Switch)
Tripped H. Utility Power Switching Device (USD) Open
F. Transfer Control in Manual (External I. Generator Power Switching Device (GSD) Open
Control Switch) J. Generator Bypass Switch (GB) Closed
G. Transfer Control in Closed Transition Mode K. Utility Bypass Switch (NB) Closed
(External Control Switch) L. Load Isolate Switch (LI) Closed
H. Utility Power Switching Device (USD) Open M. Generator Isolate Switch {GI) Closed
I. Generator Power Switching Device (GSD) N. Utility Isolate Switch {NI) Closed
Open 0. Inhibit Transfer to Utility (Source 1)
J. Generator Bypass Switch (GB) Closed P. Inhibit Transfer to Generator (Source 2/3)
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
49. Data Logging The transfer controller shall provide data COMPLY
Memory: logging and shall store the data in non-volatile SCHNEIDER ASCO ATS
memory on a removable SD memory card. The has been manufactured to operate with data logging memory
following events shall be recorded and stored: with different functionalities
A. Total Number of Transfers and the following event will be recorded and stored
B.Total Number of Transfers due to source A. Total Number of Transfers
failure B.Total Number of Transfers due to source failure
C. Number of Hours Controller is energized C. Number of Hours Controller is energized
D. Number of Hours Load is on Utility D. Number of Hours Load is on Utility
E. Number of Hours Load is on Generator E. Number of Hours Load is on Generator
generator. The unused generator will be shut soon as the Slave ATS is connected to a good source.
down as soon as the Slave ATS is connected to a
good source.
53. Lockable access doors The ATS shall be equipped with lockable access COMPLY
doors. SCHNEIDER ASCO ATS
has been manufactured to operate with equipped lockable access
doors.
54. Priorities The ATS should support selecting priorities COMPLY
among the connected DG to start and have a SCHNEIDER ASCO ATS
cyclic operation feature. has been manufactured to support selecting priorities among the
connected DG to start and have a cyclic operation feature.
55. Wiring diagram and The manufacturer shall furnish complete COMPLY
schematics schematic and wiring diagrams for the SCHNEIDER ASCO ATS
particular automatic transfer switch and a is to be supplied with complete schematic and wiring diagrams.
typical wiring diagram for the entire system
showing all components, relays and part
numbers.
All wiring and connections to integrate the ATS
into the generator output shall be made by the
vendor before acceptance by the AMN
56. Weather proof This ATS shall be an integral part of the COMPLY
enclosure generator set and be secured to the weather- SCHNEIDER ASCO ATS
proof enclosure has been manufactured to operate with an integral part of the
generator set and be secured to the weather – proof enclosure.
57. Type of transition The transfer switch shall be open transition COMPLY
type, positively electrically and mechanically SCHNEIDER ASCO ATS
interlocked to prevent simultaneous closing and has been manufactured to operate with open type transition
mechanically held in both normal and which is electrically and mechanically interlocked.
emergency positions.
58. Protection Independent break before make action shall be COMPLIANT
used as protection to prevent dangerous source SCHNEIDER ASCO ATS
to source connections. has been manufactured to operate with independent break
protection before make action be used as protection to prevent
dangerous source to source connections.
TECHNICAL SPECIFICATION FOR AUTOMATIC TRANSFER SWITCH
ፊርማ፡
ጨረታዉን አቡልኬስ ኃ/የተ/የግ ማህበርን ወክሎ ጨረታውን ለመፈረም ደንበኛ ስልጣን ተሰጥቷቸዋል፡፡
ቀን፡ 07/06/2015