Professional Documents
Culture Documents
HSE-RA-061 Table and Bench Saw - Rev 0
HSE-RA-061 Table and Bench Saw - Rev 0
PAGE No 1 of 14
AL SHAFAR GENERAL CONTRACTING LLC. REV 0
DATE 05/01/2017
SAFETY, HEALTH AND ENVIRONMENTAL PROCEDURE
Project Name: Festival Living Stream-02 HSE-RA 061
Job Description: Table or Bench Saw
Index:
Form 1 Task Analysis Initiation
Form 2 Risk Assessment Process As per Risk Assessment Procedure.
Form 3 Written Safe Work Procedure Result
AUTHORISATION
Prepared by: Approved by
Signature Date Signature Date
HSE Manager Project Manager
Impact
SEQUENCE OF TASK STEPS POTENTIAL INJURIES OR HAZARDS RECOMMENDED CONTROLS
H, S, E
1. Pre-use inspection and use of all equipment Failure of equipment will cause injuries to Faulty equipment to be repaired/maintained or replaced.
persons and / or property damage. Guards to be on all Machinery and appropriate PPE to
Faulty hand tools and power tools. be worn.
Fuel/oil leaks could cause environmental Engine ran machinery to have fire extinguishers
concerns. H, S, E
available locally.
Drip trays/heavy gauge plastic to be provided in case of
leaks and spill kit to be within the project for accidental
spills.
2. Wear appropriate Personal Protective Failure to use Personal Protective
Equipment. Equipment will cause injuries to employees.
Gloves.
Safety boots. Enforce the use of Personal Protective Equipment AT
H
Overalls. ALL times
Hard hat.
Hearing protection.
Eye protection
3. Use trained employees only All Enforce the use of competent persons only
Lack of knowledge All employees assigned to this task must be Safety
Inducted also they will have to attend a safety meeting,
Failure may result in injuries to persons and which will include the Standard Operating Procedures,
property damage. types of potential hazards, and actual hazards present
H, S
and controls for those hazards.
Workers should be legally appointed & having their Id’s.
Ensure that the operatives are physically and mentally fit
to do the activity.
5. Flying objects – saw blade disintegrating. Explain to operator how to use machine guards and not
Machine guards are in place. H,S
Severe injury to any part of the body. to work without them in place.
6. While the machine is in motion, do not allow
All employees to be instructed to visit other working
any other employees at your workplace, with Injuries to all parts of the body. H,S
stations while machines are in operation.
the exception of your assistant.
Result Classification:
Risk Rating
Critical = 17►15 High = 14►11 Medium = 10►7 Low = 6►0 16
9 Ensure that the cutting Not properly centred tool. Damage to tool H,S 9 Setting up of machine to be Supervisor Always 4
2. PROCEDURE
1. Do pre-use inspection of all equipment to be used and replace or repair faulty items.
2. Use trained competent employees only.
3. Use appropriate Personal Protective Equipment i.e.:
3.1. Hardhat.
3.2. Safety boots.
3.3. Hand gloves
3.4. Overalls.
3.5. Eye protection.
Prior to work commencement
1. Must have PPE – safety footwear, gloves, hardhat, goggles, foul weather clothing etc.
2. Must have appropriate tools and equipment in good condition.
3. Must have weatherproof covers for materials and equipment, waste containers, warning tape.
4. Consider risks and hazards in work area. Refer any concerns to supervisor. Are relevant permits in place?
5. Check if it is necessary to secure area adjacent to work. Refer to supervisor if appropriate.
6. Arrange for transport of materials and equipment to site via supervisor.
7. Ensure materials and equipment are secure or removed when site unattended, eg overnight or during breaks
Hazards
1. Manual handling of materials and equipment – LITE to be considered at all times.
2. Entanglement.
3. Slips and trips and falls from untidy work area.
QUALITY SYSTEM DOCUMENTATION
DOC No HSE-RA-074
PAGE No 13 of 14
AL SHAFAR GENERAL CONTRACTING LLC. REV 3
DATE 29 Dec 2010
SAFETY, HEALTH AND ENVIRONMENTAL MANUAL
PROJECT
Project Name: The One Tower 264
NUMBER :
Job Description: Table or Bench Saw
Persons in danger
1. Operator
2. Other workers/visitors in vicinity, eg. Passers-by in working area etc.
Control measures
No lone working
1. Do random alcohol tests on employees to ensure that they don’t arrive intoxicated or drink during working hours.
4. Never try to replace the hacksaw blade while bench saw is still connected.