Professional Documents
Culture Documents
Foundation F9
Foundation F9
Foundation F9
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 2 of 158
884 Ø12 @ 150 mm c/c Ø12 @ 150 mm c/c Ø10 @ 175 mm c/c Ø10 @ 175 mm c/c 10 – Ø25 Ø8 @ 175
mm
885 Ø12 @ 150 mm c/c Ø12 @ 150 mm c/c Ø10 @ 175 mm c/c Ø10 @ 175 mm c/c 10 – Ø25 Ø8 @ 175
mm
2.5 m 3.1 m
2m
Elevation 0.6 m
X 1.625m
1.4 m
3.25m
0.75 m
1.625m
3.25m
Plan
Input Values
Footing Geomtery
Column Dimensions
Pedestal
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 3 of 158
Design Parameters
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 4 of 158
Soil Properties
Global Settings
Top Reinforcement Option : Calculate only when foundation is subjected to uplift forces
Concrete Design Option : Net Pressure(Gross Pressure - Self Weight Pressure)
Design Calculations
Load Combinations
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 5 of 158
Moments are About the center of footing / pile cap (does not include moments caused by lateral loads)
For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical axis.
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 6 of 158
Footing Size
(Service check is performed with footing thickness requirements from concrete check)
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 7 of 158
Pressures at 4 Corners
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure will be set to zero and the
pressure will be redistributed to remaining corners.
Pressure at Pressure at
Pressure at Pressure at
bottom right bottom left
Load Case top left corner top right corner
corner corner
(kN/m2) (kN/m2)
(kN/m2) (kN/m2)
Stability Check
OTM
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 8 of 158
Load
Along X- Along Z- Required About X- About Z- Required
Case Resultant
Direction Direction FOS Direction Direction FOS
No.
Critical Load Case And The Governing Factor Of Safety For Overturning and Sliding X Direction
Critical Load Case for Sliding along X-Direction : 10
Governing Disturbing Force : 22.03 kN
Governing Restoring Force : 740.69 kN
Minimum Sliding Ratio for the Critical Load Case : 33.62
Critical Load Case for Overturning About X-Direction : 7
Governing Overturning Moment : -59.78 kNm
Governing Resisting Moment : 917.73 kNm
Minimum Overturning Ratio for the Critical Load Case : 15.35
Critical Load Case And The Governing Factor Of Safety For Overturning and Sliding Z Direction
Critical Load Case for Sliding along Z-Direction : 7
Governing Disturbing Force : -19.29 kN
Governing Restoring Force : 262.21 kN
Minimum Sliding Ratio for the Critical Load Case : 13.60
Critical Load Case for Overturning About Z-Direction : 10
Governing Overturning Moment : -68.30 kNm
Governing Resisting Moment : : 2592.38 kNm
Minimum Overturning Ratio for the Critical Load Case : 37.96
Critical Load Case And The Governing Factor Of Safety For Sliding Along Resultant Direction
Critical Load Case for Sliding along Resultant Direction : : 7
Governing Disturbing Force : 19.29 kN
Governing Restoring Force : 262.21 kN
Minimum Sliding Ratio for the Critical Load Case : 13.59
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 9 of 158
Ultimate Pressures
The base pressures reported in this table do not include the effect of buoyancy. However, the area of footing in contact includes the effect of
buoyancy (if any).
Area of
Load Case / Pressure at Pressure at Pressure at Pressure at
footing in
Load top left top right bottom right bottom left
Contact with
Combination corner corner corner corner
soil (Au)
ID (kN/m2) (kN/m2) (kN/m2) (kN/m2)
(m2)
Actual Area in Contact for all ultimate load cases exceeds the minimum required. Hence Safe
Maximum Corner Pressure from all ultimate load cases is less than the allowable. Hence Safe
Moment Calculation
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 10 of
158
X 1.625m
Z 0.865 m
1.75 m
0.865 m
Plan
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 11 of 158
X 1.625m
0.54 m 0.54 m
1.625m
Plan
X 1.75 m
Z
0.26 m
1.75 m
Plan
Ks = = 1.00
Shear Strength(Tc) = =
1250.00 kN/m2Ks x Tc
= 1250.00 kN/m2
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 12 of 158
Reinforcement Calculation
Along X Axis
Along Z Axis
24 - ϕ12
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 13 of 158
24 - ϕ12
Pedestal Design
Pedestal at Support No. Axial Capacity Ratio Flexural Capacity Ratio % of Main Steel Main Reinforcement Links
815 0.09 0.07 0.47 12-T16 + 22-T12 T8 @ 175mm
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 14 of 158
Capacity Ratios
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
Page 14 of 158
file:///D:/dinesh%20project/factory/final%20file/foundation/001/foundation/F9,P8/P8,F9/... 02-07-2023
X 1.625 m
Z
1.4 m 2.5 m 3.1 m
2m
3.25 m
0.75 m
1.625 m
3.25 m
0.6 m
Plan
1.625 m
Elevation
BOTTOM 24 - ϕ12
Foundation
3.25 m 3.25 m 0.6 m N/A 24 - ϕ12 24 - ϕ12
Plan