Professional Documents
Culture Documents
HRCAM
HRCAM
ELECTRIC SHOWER
INSTALLATION and USER INSTRUCTIONS
ref. 36 00 5804 issue 2 July 01
Model number
Cameo 7.2kW - 95 02 1645
Pressure switch
Front
cover
Flow control
valve
To close:
turn anticockwise
Inner
container
Terminal block
Rating label
red
red
red
red
black Neon
Pressure switches
black
red
Cut
Out black
green/yellow
Inner Terminal
container block
N L
Figure 2 Wiring diagram
3
CONTENTS 1 TECHNICAL SPECIFICATIONS
1.1 CONNECTIONS
Internal components .......................... p2
Inlet connection -15mm ext. diameter
Wiring diagram .................................. p2 (copper or ‘Speedfit’
Technical specifications ..................... p3 Stem Elbow)
Important information ........................ p4 Water entry point - bottom and rear
Siting and plumbing ........................... p5 Cable entry point - bottom and rear
Things you must do ........................... p5 1.2 ELECTRICAL
Electrical installation .......................... p7 Nominal Power Rating
Connecting to services ...................... p8 M odel 240V 230V
Cable entry ........................................ p9 7.2kW 7.2kW 6.6kW
30A 28.75A
Pipe entry .......................................... p9
Plumbing ......................................... p10 1.3 MATERIALS
Fitting the riser rail ................. p10 & p11 Backplate, cover
and control knob -High Impact
Fitting the wall bracket ..................... p11 Polystyrene
Fitting the hose ................................ p12 Elements -Copper sheathed rod
Electrics ........................................... p12 type
610mm (24)
the shower is adequate. If in doubt,
consult a competent plumber.
Maximum 0.7MPa (7bar - 100 psi) Shower
heater
Minimum 0.1MPa (1bar - 14.5psi)
305mm (12)
The use of other services connected to
the water pipe supplying the shower
heater may cause the water pressure to Lowest position
drop below the minimum. Therefore this
should be taken into account.
Hose-retaining ring
The following conversions may be useful:
1 bar = 14.5 lbf/in² = 33.3 ft head of water.
1 lbf/in² = 2.3 ft head.
25mm minimum
Flexible Fixed
130mm
cord wiring
6mm² cable
PIPE ENTRY
130mm 5.7 Plumbing entry can be from the rear
(preferred) or from the bottom. The
Figure 8 Positioning shower backplate has a cut out position to suit
15mm pipe. When opting for bottom
entry make cut out before fitting backplate
146 to the wall - see Fig. 11.
73
Cable
appropriate drill, obtainable from most
28 Rear entry access
Clamp area for electricty and hardware stores.
85 inlet water supplies
End cap
Rawl plug
Riser rail
Handset
holder
End bracket
Hose loop
Cover
Handseat
Hose
7 ENVIRONMENTAL INFORMATION
Heatrae Sadia products are
manufactured from many recyclable
materials. At the end of their useful life
they should be disposed of at a Local
Authority Recycling Centre in order to
realise the full environmental benefits.
14
8 USER INFORMATION Maintenance
8.1 To turn on and set temperature: 8.3 Cleaning the Handset:
1. Turn on your isolating switch. To obtain the best performance from your
2. Turn water control knob anti- shower, the handset must be cleaned
clockwise to allow water to flow until regularly, maybe as often as once a week
“power on” neon illuminates; the in hard water areas.
shower is then heating. This is because the fine outlet holes can
WARMER - DECREASE FLOW - TURN become blocked with scale and this will
KNOB CLOCKWISE affect the pattern of the spray and cause
the heater to perform poorly.
COOLER - INCREASE FLOW - TURN
KNOB ANTI-CLOCKWISE The easiest and most effective method
of cleaning your handset, regardless of
Make adjustments carefully. Give the which type you have with your shower, is
shower a few seconds after each to soak it in a proprietary descalant or
adjustment to stabilise, then check the vinegar. For best results the handset
temperature by hand before stepping into should be left to soak overnight.
the shower.
With handset types 1 & 2, the spray plate
A cold shower can be obtained simply by can be easily unscrewed by hand, should
leaving your isolating switch off and you need to give the handset a quick
operating the water control knob. clean. Use a small stiff brush such as a
8.2 To turn off: toothbrush or nailbrush to remove the
limescale, before screwing the sprayplate
1. Turn the water control knob fully back into the handset.
clockwise.
2. Turn off your isolating switch. 8.4 Inspection
We recommend that in the interests of
safety the shower and its electrical
installation is checked by a qualified
electrician at least every two years.
2. Flow adequate A. Electrical power to Ensure that the electrics to the shower are switched on,
but water too the shower heater is and the neon is lit.
cold. off.
B. Water flow too high. Reduce the flow by turning the water control knob
clockwise slowly. NOTE: If the knob is turned too far
clockwise, the safety pressure switch inside the shower
will turn off the heating elements. This is apparent when
the indicator light on the shower goes out. If this happens,
turn the knob anti-clockwise until the light comes on.
16
SYMPTOM POSSIBLE CAUSE REMEDY
3. Water too hot. A. Water flow too Increase the flow by turning the water control knob anti-
low. clockwise.
B. Spray plate Clean the handset spray plate.
blocked with scale
or debris.
5. “Power on” A. Cartridge fuse or Switch off shower and isolating switch.
indicator not lit. miniature circuit Renew fuse or reset the mcb. If they operate a second
Isolating switch breaker (mcb) has time, contact a qualified electrician.
“On” but its operated in your
neon not lit . fusebox (or
consumer unit) or
switch fuse.
B. Residual current Follow the same procedure as above. If this has
device (rcd) or happened with a “split load” consumer unit on initial
(earth leakage installation, check that the neutral core of the shower feed
circuit breaker) cable is connected to the “protected” neutral bar of the
has operated. unit.
6. Water emerges PRD has operated 1. Switch off immediately at isolating switch.
from bottom of 2. Turn water off at the servicing valve (if fitted) or stop
the unit. valve.
3. Contact Heatrae Sadia Service Department.
Due to continuous improvement and updating, specifications may be altered without prior notice.