Professional Documents
Culture Documents
Vol. II
Vol. II
THIS PAGE IS A RECORD OF ALL SPECIFICATION REVISIONS. NORMALLY, REVISED SHEETS ONLY ATTACHED
EACH TIME THE SPECIFICATION IS CHANGED ONLY THE NEW OR REVISED ENTIRE SPECIFICATION RE-ISSUED
PAGES ARE ISSUED. ENTIRE SPECIFICATION REVISED
SPECIFICATION REV.
ECG ENGINEERING CONSULTANTS GROUP S.A. TABLE OF CONTENT
CAIRO - EGYPT 000010 - 2874 0
CONTENTS
VOLUME I
GENERAL REQUIREMENTS
VOLUME II
DIVISION 0: INFORMATION
VOLUME III
Divisions 03 Concrete
Divisions 04 Masonry
Divisions 05 Metals
Divisions 08 Openings
Divisions 09 Finishes
Division 10 Specialties
101405 Signage
101453 Traffic Signage
102113 Toilet Compartments
102600 Wall And Door Protection
102800 Toilet and Bath Accessories
Divisions 11 Equipment
VOLUME III
210548 Vibration And Seismic Controls For Fire-Suppression Piping And Equipment
211000 Water-Based Fire-Suppression Systems
211339 Foam-Water Systems
212100 Carbon Dioxide Fire Extinguishing Systems
212200 Clean-Agent Fire Extinguishing Systems
213113 Electrical-Drive, Centrifugal Fire Pumps
213400 Pressure-Maintenance Pumps
Division 22 Plumbing
VOLUME III
Division 26 Electrical
Division 27 Communications
Division 31 Earthwork
Division 33 Utilities
SPECIFICATION REV.
ECG ENGINEERING CONSULTANTS GROUP S.A. METHOD OF MEASUREMENT
CAIRO - EGYPT 012700 - 2874 0
METHOD OF MEASUREMENT
1. These notes are intended as a guide only to the method adopted in the preparation of the
Bill of Quantities and the measurement of the Works. Contractors must note that rates
for items must include furnishing and everything necessary for the proper execution,
erection, completion and maintenance of each item and that all auxiliary work is included
unless specifically otherwise stated, measured or excluded in writing by the Engineer.
3. Rates must include work at all levels, furnishing, transportation and installation, materials
and goods, scaffolding and testing where applicable. Each item includes also, unless
otherwise specifically stated, all labor in making, materials, goods and all costs in
connection therewith (e.g. conveyance, delivery, unloading, storing, unpacking, returning
packing, handling, hoisting, lowering and the like), fitting, setting and fixing materials and
goods in position, all square raking and curved cutting, waste of and laps in materials, use
of plant, temporary works, patterns, models, templates, samples and establishment and
overhead charges and profit.
4. Quantities are billed to the nearest whole unit. Fractions of a unit less than half are
disregarded and all other fractions are regarded as whole units.
7. Attention is also directed to the Specifications and Drawings, which contain further notes
on all work, required and which are deemed to be included in rates quoted in attached
Bills of Quantities.
9. Rates include cost of removal of rubbish and debris from the site.
11. Rates for all equipment include testing at manufacturer’s premises and all spare parts
needed.
12. Rates shall represent full compensation for all plant, materials, transport, labor,
equipment, temporary works, establishment, overhead, profit, and tax charges required
to complete the work described in this sub-section of the specification and/or on the
drawings.
13. Rates shall include all facilities and equipment for testing and inspection by the Employer's
representatives.
CONCRETE
Plain Concrete
Furnishing all required field tests, survey works and design documents
and submit for engineer’s approval.
Furnishing moulds, casting..etc.
Construction requirements of handling, concreting, testing, cutting, ,
storing, transporting, , ..etc.
Furnishing connections, bolts, welds, grout materials, fabrication,
MASONRY
Measurements shall be for net areas; areas less than 0.25 sq.m will not be
deducted.
Furnishing of all materials, which include but are not limited to stone,
special pieces, end and corner units.
Setting materials, grout and sealants.
Anchors, fasteners.
Grinding, mitering, and beveling.
Fixing in position and scaffolding.
Stone accessories.
METALS
Section Unit Description
Ton Purlins Classified according to the type of purlin sections, measured by weight
of furnishing, installing, erection and coating.
m2 Thermal insulation:
OPENINGS
No. Classified according to type, finish, and size, fire rating period as per Drawings
& Door Schedules.
No. Classified according to type, material, finish, size and fire rating period as per
Drawings.
No. Classified according to type, size, finish, frame type, and fire rating period as
per Drawings & Door Schedules.
No. Classified according to type, size, and finish as per Drawings & elevation
Schedules.
No. Classified according to type, finish, and size as per Drawings & elevation
Schedules.
No. Classified according to type, finish and size as per Drawings & windows
Schedules.
No. Classified according to hardware set as per Door hardware set Schedule.
088000 Glazing
Glazing shall not be measured separately for payment and shall be paid as part of
the Contract unit price for the associated work requiring glazing and to include the
following:
088300 Mirrors
FINISHES
Floor Tiling
Wall Tiling
Ceramic Skirting
Terrazzo base
m Vanity top.
m For skirting.
099100 Painting
Furnishing and applying the paint system including primer, intermediate, top
coats, preparing surfaces, rubbing down between each coat, stopping,
knotting.
Covering of floors, with sheets while painting is being executed, removing paint
splashes, spots, and stains and completion of work to perfection.
Painting on other items such as metal and wood shall not be measured
separately for payment and shall be paid as part of the item.
Repairing of damaged parts.
Cleaning.
Any other required items as per Drawings and Specifications.
SPECIALTIES
The rates shall be full compensation for all plant, materials, transport, labor,
equipment, temporary works, establishment charges, overheads and profit
required to complete the works described in this Section of the Specification
and/or shown on the Drawings.
Pilasters.
Doors.
Hardware.
Supplying all necessary materials, fabrication to detailed Drawings.
Fixing in place, supplying and installing all required hardware and accessories,
finishing, cleaning, etc.
EQUIPMENT
No Speed Hump
No Rising Arm
SPECIAL CONSTRUCTION
CONVEYING SYSTEMS
No. Classified according to type, rated loads, speed, operation system, number of
stops, opening, and finishes.
Rates shall include the following:
Issuing all security permits needed from related authorities for this labor
and staff and to comply with working hours determined by the related
authorities.
All necessary engineering drawings, tools, labor, calculations, equipment,
power, control and material required for installation and erection and
operation.
Fixing in position with necessary inserts, beams, fasteners, and scaffolding.
Furnishing, installation of elevator.
Fire protection, and demonstration to building municipalities.
Civil works related to building (hoist way and pit) special services, systems
and interface such as detectors, BMS, paging, lighting, earthing, vibration
and noise dampers, warning signs, … etc. as per specification.
Adjusting, testing, devices, acceptance and operation so as to be ready for
handing over to the employer, and authority bodies.
Maintenance and training.
Safety features required for personal life and building.
FIRE SUPPRESSION
m Piping
No. Valves
No. Sprinklers
Foam Concentrate
Supply of foam.
Foam proportioners
Control Panels
Horn/Strobe Units
Alarm Bells
Strobe lights
Discharge Nozzles
Warning signs
Piping Network
Classified by material.
Control Panels
Alarm Bells
Strobe lights
Abort switches
Discharge Nozzles
Warning signs
Piping Network
Classified by size.
PLUMBING
Piping
Valves
This method is applicable for all types of valves, unless otherwise indicated
Furnishing and installing hose bibs with hose connection, vacuum breaker,
accessories, fittings, supports, fixation, operating handle and keys, and
putting into service.
Furnishing roof drain complete with doom, flashing ring, gravel stop,
extension callers under-deck clamp and sump receiver, and special pieces.
Installation and fixation.
Commissioning.
Supply of pump sets complete with electric control panels, all accessories,
strainers, pressure switches, fittings, fasteners, supports, bracing, gaskets,
and bolts.
All necessary wiring, power cables, vibration isolators prefabricated
bedplates, connecting flanges complete with tapping, motors, casings,
impellers, couplings, bearings and seals, casing, air release valves, pressure
regulators, pressure gauges, pressure switches, glands, starters, control
and remote devices, control cables, control valves.
Seals, bearings, delivery, bends, guide rails, float switches, lifting chains
with identification tags.
All special pieces for installation and operation.
Foundation blocks, spare parts, Installation.
Connection to piping.
Commissioning and putting into service.
Supply of pump sets complete with electric control panels, all accessories,
strainers, pressure switches, fittings, fasteners, supports, bracing, gaskets,
and bolts
232113 HVAC
To
238400 General
Contractors must note that rates of items include everything necessary for the
proper supply, installation, execution, completion, start-up and maintenance
of each item that all auxiliary work is included unless specifically otherwise
stated, measured or excluded in writing by the Engineer.
Rates shall be fully inclusive of all that is necessary to fulfill the liability and
obligations and shall include:
Furnishing.
Insulation.
Installing and testing at manufacturer’s premises and on the site.
Sheet Metal Duct Work
m Circular, oval and flexible ductwork are measured by length along the
centerline over all fittings and are classified by diameter. Ductwork shall be as
indicated on the drawings.
m Piping
- Supply and install insulation for duct and pipe works according to the
specification and as shown on drawings.
- Complete with fasteners, vapor barriers, adhesives, cladding, cloth
wrapping, painting, coating, tags, flow indicators, labels and color code or
the like.
Valves, fittings, bases, control, vibration isolators, sound lining, all required
joints, accessories, and the like.
Automatic control systems shall be as items for each control panel common to
each system on installation.
Civil works of HVAC system shall not be measured separately and shall be
included in rates of other items of HVAC works.
INTEGRATED AUTOMATION
Supply, install, test, commission, start-up and hand-over & compatible with
all other system elements including, power cables, communication cables,
interface software, terminations, labeling.
All necessary accessories required to complete the work.
No. Hand held operator unit allowing accessing the whole network controllers
from any place on the network
Supply, install, test, commission, start-up and hand-over & compatible with
all other system elements including, power cables, communication cables,
interface software, terminations, labeling.
All necessary accessories required to complete the work.
L.S. Direct Digital Controller (DDC), Local Control Panel (LCP) and Integration
Automation Controller (IAC)
ELECTRICAL
Outlets Fittings
Supply, install, connect, test, delivery, put into operation The Dry type
transformer with all accessories mwntion the specifications.
Supply, installation, termination for M.V. and L.V.
Installation, connection, grounding tapes, enclosure, ventilation fans, PTC
sensors, thermal controller unit and tranfered with the BMS.
Testing and commissioning.
Associated civil work relevant to fixation and installation, catalogues
262413 Switchboards
263533 Power Factor Correction Capacitors
Outlets Fittings
- Supply, installation, testing and commissioning of the unit with control panel,
Sound Attenuator, Silncer, muffler, Exhaust system with insulation, fuel oil
system, daily tank, monthly tank, electric pump, manual pump, pipes, valves
and accesories.
- Provision of connections between fuel storage tank and daily tank and
solenoid valve required, cooling, set of pumps, exhaust system, lubrication
system, grounding tapes, noise suppressors, vibration suppressors, ventilation
works, concrete base and louvers.
- Spare Parts
- All associated civil work relevant to fixation and installation.
- Detailing, fabrication, delivery, assembly, installation of all accessories.
- Testing before shipping and on site after installation of the complete
system, spare parts, catalogues and manuals.
- And all necessary accessories to complete the work according to the
technical specifications and the other contract documents.
No. Classified by rating, voltage, type and minimum duration of back-up supply.
COMMUNICATIONS
No. RJ54 Cat (6A) Patch Panel (6A) Port, Fiber Optic Patch Panels (LC), (SC/APC)
Type, Management panel (mounted in TCs).
No. Patch cord (F/UTP) Cat (6A) - (X) meter for rack patching/work area and Fiber
optic duplex patch cord LC, SC/APC (Single) / (Multi) Mode (X) meter,
(connector types according to supplied switch types).
m (OM4 Multi-Mode) fiber optic cables (x) core LSZH (Indoor) type
No. Rack/Cabinets, Fiber terminal box (FTB) & Optical distribution frame (ODF)
L.S Core switch, HOT redundant Core switch, Firewall, Wide Area Networking
Internet Routers, and Network Management Software
No. Speakers (Fire rated Ceiling Speakers, column speakers & outdoor horn
speakers)
Supply, install, test, commission, start-up and handover & compatible with
all other system elements including matching transformers, mounting
brackets/plates, fire rated back boxes, conduits, boxes, raceways, flame
retardant cables, connectors, terminations, and labeling.
All necessary accessories required to complete the work.
Supply, install, test, commission, start-up and handover & compatible with
all other system elements including mounting brackets, stands, boxes,
conduits, raceways, cables, connectors/jacks, terminations, and labeling.
All necessary accessories required to complete the work.
Supply, install, test, commission, start-up and handover & compatible with
all other system elements including override relay, boxes, back boxes,
conduits, raceways, cables, connectors, terminations, and labeling.
All necessary accessories required to complete the work.
No. Racks
No. Card Issuing Printer c/w Digital Video Capture Camera and Fingerprint
enrolment unit
Rates shall include supply, install, test, commission, start-up and hand-over
including, power cables, communication cables, interface software,
terminations, labeling
All necessary accessories required to complete the work.
No. Proximity Readers, fingerprint reader with keypad, Door Sensors, Door Locks,
Request to exit buttons, Security Break Glass and Security Buzzer.
No. Enter/Exit terminal unit, directional ultrasonic sensor, outdoor parking main
display
No. Parking Controller to interface with the car barrier, Raising Arm barrier (x m)
length c/w underground loop detector & manual reset switch
L.S. Network Video Storage system (X) days for all cameras & Video wall Array [N
row x N column] c/w video wall controllers, decoders, software & all hardware
modules
No. Workstation
No. Indoor/Outdoor IP Fixed Dome 2MP Camera, Outdoor IP fixed wall 2MP
Cameras & Outdoor PTZ dome 2MP camera
Supply, install, commission, start-up and handover & compatible with all
other system elements including housing, power supply, IR illuminator for
outdoor cameras, mounting brackets, conduits, boxes, raceways, cables,
terminations, and labeling.
All necessary accessories required to complete the work.
No. Initiating Devices (Heat Detector, Multi sensor detectors, Manual Station,
Linear heat detector, Beam detector, etc.)
No. Interfacing Devices (Control modules, Monitor modules,…etc) & Fire alarm
interface unit (IFU)
Supply water leakage control panel c/w with alarm modules, enclosure,
audible alarms, I/O modules and communication interfaces, install,
programming, connection software and hardware and all required for
interface with (fire alarm system), testing, commission, start-up and hand-
over, including Power Supply, batteries, conduits, boxes, raceways, cables,
communication cables with other fire alarm control panels including,
terminations, connection with earthing, labeling.
All necessary accessories required to complete the work.
No. Water Leakage Leader Cable, Water Leakage Sensor Cable, WLD siren with
strobe, End Termination Kit and Remote Alarm.
EARTHWORK
Section Description
Excavation m3
Backfilling m3
EXTERIOR IMPROVEMENTS
The unit of measurement of the Graded Crushed Aggregate Base Course shall
be the square meter (m2)
The quantity shall be computed from the theoretical values indicated on the
Drawings, flat on plan. Thickness shall be that shown on the Drawings.
The rates shall be full compensation for all plant, materials, transport, labor,
equipment, temporary works, establishment charges, overheads, profits and
taxes required to complete the work described in this Section of the
Specification and/or shown on the Drawings.
- Delivery to site
- Taking from stockpiles
- Loading and hauling
- Producing, crushing and screening
- Multiple handling
- Depositing, spreading and compacting
- Maintenance / repair work
- Side and end waste
- Testing
Furnishing materials.
Substrate preparation.
Setting and grouting materials.
Sand bedding, compaction of soil, leveling, and jointing.
Geotextile fabric.
Any other required items as per Drawings and Specifications.
Work under this Section shall be measured according to the item classifications
and units contained in the Bills of Quantities (BOQ). Unless classified otherwise,
Curbstone and Gutters shall be measured in linear meter (m).
The rates shall be full compensation for all plant, materials, transport, labor,
equipment, temporary works, establishment charges, overheads, profit, and
taxes required to complete the work described in this Specification and/or
shown on the Drawings.
Rates for the Curbstones and Gutters shall further include for:
- Concrete foundations including all excavation, disposal, concrete,
reinforcement and formwork
- Bedding, jointing and pointing in cement mortar
- Concrete backing and steel dowel bar reinforcement to curbs
- Specially manufactured shaped curbs at all crossovers, intersections,
ramps, radiused bends and curves
- Providing curbstones and gutters as in-situ concrete, if so approved by
the Engineer
The units of measurement of the pavement markings shall be the square meter (m2).
The rates shall be full compensation for all plant, materials, labor, equipment,
transport, temporary works, establishment charges, overhead, profit and
taxes required to complete the work described in this Section of the
Specification and/or shown on the Drawings.
No. Cranes
Are classified according to lifting capacity. Rates shall include supply and
installation of all necessary girders, traveling rails and beams, wheels, and
carriage limit switches, control panel of control devices safety devices, cables,
festoon, steel fabrication fasteners, crane trolley, chains and all accessories
required for proper operation testing and putting into services.
SPECIFICATION REV.
ECG ENGINEERING CONSULTANTS GROUP S.A. BILL OF QUANTITIES
CAIRO - EGYPT 012750 – 2874 0
SPECIFICATION REV.
ECG ENGINEERING CONSULTANTS GROUP S.A. LIST OF MANUFACTURERS
CAIRO - EGYPT 012950 – 2874 0
1. Contractor should abide by the manufacturers listed below OR equal approved by the
Engineer, comply with the Project Specifications, obtain accredited Test Reports along
with approved record of similar successful interventions in projects.
a. A letter from the Mother Company listed in the LOM certifying that the submitted
product is manufactured in that factory in such location under the Company
quality control protocol and supervision, and stating that the factory is one of the
Company’s accredited factories.
b. In case of any deviation from Specifications and specified performance
requirements, Engineer has the right to request further testing in an approved
independent laboratory accepted by the Engineer on Contractor's Expense to
demonstrate compliance of the product with the Project specifications.
SECTION
PRODUCT MANUFACTURER
No.
033000 Steel Reinforcement Steel Ezz – Dekheila
131500 Reinforced Concrete Water Structures Steel Bishai
Egyptian Steel
Solb Misr
El Attal
Cast in Place Concrete Decom
Cemex
Ready Mix Beton
Lafarge
Unimex
Reliance
034800 Precast Concrete Parking Bumpers Samcrete
Arab Contractor
Premco
Modern Concrete
CPD
033316 Light Weight Concrete Cemex
Lafarge
035440 Cement Screeds Cemex
Lafarge
042000 Concrete Unit Masonry Arab Contractors
Egyptian American Co.
CPD
Samcrete
Toblat
Cementa
ESG-Egyptian Stones Group
Masonry Accessories Metal X
Unitech
Bridg Egypt
044200 Exterior Stone Cladding MK ممدوح كساب
096340 Stone flooring Modern Marble
097500 Stone Facing HAZ Marble
Kiro Marble
Marmonil
Diamond