Professional Documents
Culture Documents
Agilent 1090 Diagnosis
Agilent 1090 Diagnosis
xxEjEg'I'i-7t"~iINTD. SAMPLE. + n·
Ejects specified vohime into a.ctu~l vial number pIns
specified nnmber (default n:::O).
;i'··E:.J~S]W·[~f.tf~~d¥'NT5"'"'9A~T§!:ii";:';···'·
EJects speCifi~d ~o'lum~into;a,ste--=i~~jection needle is
seated and rotary valve connects syringe to waste.
Limits: 0.1 pI through MAX!NJVDLUM (for volume).
·'k:k:'.EjE:C±i;HgffGl••·.·. iNTb".AI~.i··· .,
Ejects specified volume into air·-injection needle is up
(not sea,ted) a,nd rotary valve connects syringe to open
cnd (air).
Limits: 0.1 t'J through MAXINJVOLUM (for volume).
~~'M±XJ..22--ul CYCLES.. 1
Moves specified volume back and furth in sample loop.
Mixing is done with injector needle up (mix in loop).
This mixing is repea,ted according to the number of
cycles you specify.
Limits: 0.1 pI through MAXINJVDLUM (for volume) and 1
through 999 ([or r.yc1es).
XiMIXV'::::'::'~ul CYCLES 1
Moves specified volume back and forth in sample loop.
Mixing is done with injector needJr in the vial la.st
ilt specj·rted in injector program (mix in vial). This nlixing
is repeated a.ccordi ng to the number of cycles YOll
specify.
Limits: 0.1 ,ul through MAXINJVDLUM (for volume) and 1
through 999 (for cycles).
£xWA 11'9.0 mih
;," .. "".. ,.... ,:,,',,
"" ",,""""'." ',.",,, ,,'.' '"
.
Waits specified time and then continues with next lille ,in
injector program.
xJC.Jin5~;S12;·.~~11i~t··d·····.··MAIrJPASS····.····
Moves rotary va.lve to injector loop (needle is seated a.,nd
solvent flows through needle).
~~::1~~~~i~$~~~yt~~~~~:~"g¥t~~~~~§~i0&,£,i,i:,~\i
Moves rotary valve to bypass position, isolating the
reaction capilla.ry. This command is used as a last entry,
following INJECT a.nd is used when a micro-oven is
installed. This command must follow INJECT if injector
program contains further lines.
'g¥,j~'~~~ii~~~~lJi,§~~~:i;~1~@1£~;~~)':ii!'U;;:l%i
Controls the EVENT contacts El through E4 on the re<'l,r
panel of the HP 1090 and the column switching valve cs.
.--
Limits: 0 for open or inactive; 1 for closed or activej '2
for leave in current setting.
See "( E.t Cont )" a,ud "( Column Switch 1" for detail5.
U~'Cq,,~
down moves rotary valve
to injection mode: sample loop is reconnected to the
solven,t flow; the sample is flushed out of the injector and
.-'--
into the col umn.
After injection, the HP 1090:
• Creates start signal at REMOTE CONTROL
connector;
• Starts time program;
• Creates signal at DCD connector according to vial
number.
•
'-
,.,-
4-24 ' Parameter Keys
PAGE 48
01/21/2004 09:48 8153511974 PRIMUS
7
Auxiliary Functions
',---
.'~
., ,"'.
~4
RESET INJECTOR
RESET INJE:CTOR sets auto-injector and auto-sampler in ~
correct starting position. -'
Limits: None-to reset, press (Ente,). ~'
~ -
Use RESET INJECTOR after an injector error has occurred.
I
']
.~
...-
MAXFLOW@P
.-_H :I .... I
I
MAXFLOWlOP sets a pressure limit for solvent delivery
i;ystem when troublcshootin"g, see your III' 1090 guide
books. If li mit reached, solvent delivery system continues
to pump solvent but reduces flow.
-.- .....-
I
'
I
-- I
--- I
-.- I
Limits: 0 for function not used or 1 through 400 bar.
I
I
MAXINJVOLUM MAXINJVOLUM"'25
-, !,
;,I,
avaoila,ble as an accessory.
- , ,
-- I.
•-
. ...... ,
TIME
Time sets the current time (24-hour clock!).
Limits: Time in hours (HH), minutes (MM), and seconds
(33). Setting time clears status logbook, see Cha.pter 8.
ABORT
ABORT resets the HP 1090 for operation.