Professional Documents
Culture Documents
DAS Fiber Transport V1.3
DAS Fiber Transport V1.3
DAS Fiber Transport V1.3
GENERAL DESCRIPTION
Optical Zonu’s RF over Fiber Link (RFoF) functions as a simple,
easy-to-use, DAS Fiber Transport System. The typical field
application is an environment where a BTS, or Donor Antenna,
is connected to the DAS Head-End at multiple Hub locations.
Instead of using inefficient, loss-prone coaxial cable, system
integrators may run single mode fiber optic cable to transport
any type of RF signal with this system. This system consists of
high performance, protocol independent, and broadband RFoF
Transceivers with very wide Dynamic Range designed for the
transport of Linear Analog RF signals over long distances for
variety of Frequency bands. It is designed to carry all licensed and unlicensed bands and technologies such as
LTE, GSM, CDMA UMTS/WCDMA and EVDO optimized for 100 MHz and 2200 MHz.
FEATURES
OZC Fiber Optic Links offer convenient and cost effective methods to transport analog RF signals. Individual
fiber optic transceiver (paths) are assigned to each cellular band, to avoid complex RF processing which could
impact Intermodulation Distortion. The input levels of the Optical Zonu Fiber Transport match the input
levels of all major manufacturers’ DAS Head-Ends from -20 dBm to +10 dBm.
Reduce OSP Costs - Single Fiber per Sector Simple to Deploy (Plug-and-Play)
Fewer Connectors - Lower Cost per Sector Easy Installation
Cost Effective and Upgradable Made in USA
Low Failure Rate Shorter Lead Time
Easy to Maintain and Service Excellent Support
15028 DELANO ST, VAN NUYS, CA 91411 TEL: 1 818 780 9701 FAX: 1 818 780 9739
BTS Fiber Transport Link for DAS
Low Noise RF over Fiber Link
Illustration of two stand-alone transceivers connected with a single fiber optic cable.
TECHNICAL SPECIFICATION
RF SPECIFICATION
Downlink (DL) Uplink (UL)
Typical Downlink NF < 1 GHz 38 dB Typical Uplink Noise Figure (NF) < 1 GHz 17 dB
Typical Downlink NF @ 1 GHz 39 dB Typical Downlink Noise Figure (NF) @ 1 GHz 19 dB
Typical Downlink NF @ 2 GHz 42 dB Typical Downlink Noise Figure (NF) @ 2 GHz 22 dB
Flatness across the 100 MHz to 2.2 GHz + 1.5 dB Flatness across the 100 MHz to 2.2 GHz + 1.7 dB
Flatness in any 60MHz across the full band + 0.5 dB Flatness in any 60MHz across the full band + 0.6 dB
SFDR 2/3(dBm-Hz) 110 SFDR 2/3(dBm-Hz) 110
Max RF input power into Master Unit (DL) +10 dBm Max RF input power into Remote Unit (UL) -10 dBm
Intermodulation (IMD) @ +7dBm/tone -39 dBm Intermodulation (IMD) @ -20dBm/tone -80 dBm
Link Gain (typical) 0 dB Link Gain (typical) 0 dB
IIP3 +30 dBm IP3 +10 dBm
OPTICAL SPECIFICATIONS
Optical Link Budget -20 to +10 dB without AGC
Output Power (Optical) 2 to 5 mW
Operating Wavelength CWDM Grid
Typical Fiber Loss 0.3 - 0.38 dB per/km
MECHANICAL DIMENSIONS
Dimensions of Master Unit (OZ9000): 19”x 1U x 15”
Dimensions of Stand-alone Unit: 3” x 1.5” x 5”
ADDITIONAL INFORMATION
SC/APC is standard. FC/APC or LC/APC are also available
RF impedance is 50 ohm SMA. QMA or N-Type connectors are also available.
Master and Remote chassis are equipped with standard dry contact alarm.
Visual front panel LED indicators are standard for power and optical link status.
ORDERING INFORMATION