Professional Documents
Culture Documents
Load Calculation of Steel Handrail
Load Calculation of Steel Handrail
1. BASIC DATA
1.1Standards
1.2 Materials
1.3Loading
1.3.1 Dead Load
1.3.2 Wind Load
3. PROFILE PROPERTIES
3.1 80X80X2mm Steel tube for the handrail.
3.2 100X100X3mm Steel tube for the handrail.
4. WIND LOADING
4.1 Wind Loading for the handrail.
5. STAAD ANALYSIS
5.1.1 Loading
5.2.2 Displacement Check
5.2.3 Steel Stress Check
5.1.2 Results
Pg-01
6. CONNECTION DESIGN
6.1 Base plate design
8. REFERENCE
1 BASIC DATA
1.1 Standards
ADM 2015 Aluminium design manual
SBC-301 Saudi building code, deflection requirement
ASCE7-2016 American Society of Civil Engineer, Wind load design
Chapter 30
AISC 360-10 American Institute of steel construction Steel connection
design
ASTME-1300 Standards practice for determining Load resistance of
glass design in building.
AS1288
Software used.
Staad pro connect edition and Hilti for connection.
1.2 MATERIALS
Aluminium Extrusion profiles (6063-T6 Alloy)
Rm=185 MPa
P0=160 MPa
Steel plates and section
S275
Py=275 MPa
Bolts& Screw
A4-Stainless steel
Pg-02
Pf=450 MPa & Pu=700 MPa
1.3- Loading
1.3.1Dead Load
Dead Load of Aluminium sheet 0.07 Kpa is considered along with self-weights
of steel tube framing and accessories are considered in the model.
1.3.2Wind Load
Wind speed 46 m/s 3sec gust wind speed as per Saudi SBC is considered for
wind analysis ASCE7-2016,
And Wind Pressure of 1.93 Kpa is calculated as per ASCE-2016 is applied on the
model
Pg-03
Ultimate Limit state
1.2 Dead Load+1.6 Wind Load
0.9 Dead Load+1.6 Wind Load
2. Steel Handrail
2.1 Loading and Layout
Steel handrail welded framing is of 1.47m cantilever supported on the concrete
The steel tube 100x100x3mm (Angle) is used with the base plate.
And for the remaining portion 80X80X2mm Profile is used here.
The handrail is designed for wind and corresponding live loads.
The Staad analysis is done for to justify the steel section sizes.
Pg-04
4. Wind Loading
4.1 Wind Loading at Ground Floor
Wind loading calculation in accordance with ASCE 7-16
h= 23 m
Cat C
V= 46m/s
Kd= 0.85 From Table 26.6-1
Kz = 1.17 From Table 26.10-1
Kzt= 1.00 From Table 26.8-1
Ke = 1.00 From Table 26.9-1
GCpn for parapet =1.5 for windward From ASCE 7-16 Pg-274 (27.3-3)
Pd=qz(GCpn) =1.289(1.5)
Pd=1.93 Kn/m2
Hence use typical pressure 1.93Kpa for the handrail.
Pg-05
S.S.L +19.95 30126
RFL 2317 2317 2317 2317 2317 2317 2317 2317 2317 2317 2317 2317 2317
1220
1224
150
1170
1220
250
270
1150
REFERENCE DRAWING
Pg-06
30
150
210
30
30 150 30
210
Pg-08
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 3
Print Time/Date: 11/07/2023 15:16 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-09
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
30.121m
Y
X
Z 1.470m
Load 3
DIMENSION
Print Time/Date: 11/07/2023 15:17 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-10
Steel tube is used here for the handrail
Pg-11
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 1
Print Time/Date: 11/07/2023 15:43 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-12
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
-0.740 kN/m
Y -0.740 kN/m
X
Z
Load 1
Handrail in usual situations will not be subjected to any load as people will just hold it for
support. But sometimes people may lean on it. Hence I considered0.74 Kn/m an udl
and design it as a continuous or simply supported beam.
Mostly it is standardized design.
Print Time/Date: 11/07/2023 15:22 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-13
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 2
Wind Pressure 1.93 KPa is applied here as the exposed face of steel bar
Print Time/Date: 11/07/2023 15:24 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-14
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 3
For Serviceability
DL+WL
Print Time/Date: 11/07/2023 15:25 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-15
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
0.338
0.519
0.338
0.888
0.338 0.2010.288
0.318
0.92
0.338 0.2010.493
0.55
0.928 0.512
0.338 0.201 0.569
0.929
0.338 0.2010.516
0.573
0.93 0.516
0.338 0.201 0.574
0.93
0.338 0.2010.516
0.574
0.93 0.516
Y 0.338
0.93
0.2010.516
0.574
0.201 0.574
X 0.338
0.338
0.929 0.516
0.201 0.574
Z 0.338
0.338
0.92
0.928
0.516
0.201 0.573
0.2010.516
0.574
0.888
0.2010.512
0.569
0.519
0.2010.493
0.55
0.288
0.318
Load 3
Print Time/Date: 11/07/2023 15:27 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-16
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:27 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 2
Pg-17
Job No Sheet No Rev
2
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:27 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 2 of 2
Pg-18
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
X = 0.000 kN
Y = 0.973 kN
X = 0.000 kN
Z = 2.728 kN
Y = 1.842 kN
X = 0.000 kN
Z
Y = 1.842 kN
X = 0.000 kN = 5.456 MX = 2.856 kN-m
kN
MX
Z = 5.456 kN
Y = 1.842 kN = 4.931MY = 0.000 kN-m
kN-m
X = 0.000 kN
MX = 5.109MY
Z = 5.456 kN
Y = 1.842 kN = 0.000MZ
kN-m = 0.000 kN-m
kN-m
X = 0.000 kN
MX = 5.141MY
Z = 5.456 kN
Y = 1.842 kN = 0.000MZ
kN-m = 0.000 kN-m
kN-m
X = 0.000 kN
MX = 5.148MY
Z = 5.456 kN
Y = 1.842 kN = 0.000MZ
kN-m = 0.000 kN-m
kN-m
X = 0.000 kN
MX = 5.149MY
Z = 5.456 kN
Y = 1.842 kN = 0.000MZ
kN-m = 0.000 kN-m
kN-m
X = 0.000 kN
MX = 5.149MY
Z = 5.456 kN
Y = 1.842 kN = 0.000MZ
kN-m = 0.000 kN-m
kN-m
X = 0.000 kN
Y = 0.000MZ
MX = 5.149MY
Z = 5.456 kN kN-m = 0.000 kN-m
kN-m
Y = 1.842 kN
X = 0.000 kN
MX = 5.149MY = 0.000MZ
kN-m = 0.000 kN-m
kN-m
X
Z = 5.456 kN
Y = 1.842 kN
X = 0.000 kN
MX = 5.148MY
Z = 5.456 kN MZ =
= 0.000 kN-m
kN-m 0.000 kN-m
Y = 1.842 kN
X = 0.000 kN
Z MX = 5.141MY
Z = 5.456 kN
Y = 1.842 kN
X = 0.000 kN
MX = 5.109MY
Z = 5.456 kN
Y = 0.973 kN
MZ
= 0.000MZ
kN-m
=
= 0.000 kN-m
kN-m 0.000
= 0.000 kN-m
kN-m
kN-m
MX = 4.931MY
Z = 2.728 kN = 0.000MZ
kN-m = 0.000 kN-m
kN-m
MX = 2.856MY MZ =
= 0.000 kN-m
kN-m 0.000 kN-m
MY = 0.000MZ = 0.000 kN-m
kN-m
MZ = 0.000 kN-m
Load 3
Print Time/Date: 11/07/2023 15:27 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-19
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 3
X = 0.000 kN
Y = 1.842 kN
Z = 5.456 kN
MX = 5.148 kN-m
MY = 0.000 kN-m
Print Time/Date: 11/07/2023 15:38 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-20
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:28 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-21
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
Max FX 43 1:DL 0 0.973 0 0.244 0 0
Min FX 43 1:DL 0 0.973 0 0.244 0 0
Max FY 55 1:DL 0 1.842 -0.000 0.455 0 0
Min FY 56 2:WIND PRESSURE 0 0.000 2.728 2.612 0 0
Max FZ 49 2:WIND PRESSURE 0 0.000 5.456 4.692 0 0
Min FZ 47 1:DL 0 1.842 -0.000 0.458 0 0
Max MX 49 3:COMBINATION LOAD CASE
0 3 1.842 5.456 5.149 0 0
Min MX 43 1:DL 0 0.973 0 0.244 0 0
Max MY 43 1:DL 0 0.973 0 0.244 0 0
Min MY 43 1:DL 0 0.973 0 0.244 0 0
Max MZ 43 1:DL 0 0.973 0 0.244 0 0
Min MZ 43 1:DL 0 0.973 0 0.244 0 0
Print Time/Date: 11/07/2023 15:28 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-22
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Max: 11.774 mm
Max:
Max: 19.433
19.011 mm mm
Max: 22.679 mmMax: 0.714 mm
Max: 20.020 mmMax: Max: 0.237
mm mm
Max: 23.287 mmMax: 1.2253.950
mm
Max: 20.232 mm Max:
4.2210.408
mm mm
Max: 23.415 mmMax: Max:
1.272 mm
Max: 20.278 mm Max:
4.2480.423
mm mm
Max: 23.443 mmMax: Max:
1.281 mm
Max: 20.287 mm Max:
4.2530.426
mm mm
Max: 23.448 mmMax: Max:
1.282 mm
Max: 20.289 mm Max:
4.2540.426
mm mm
Max: 23.450 mmMax: Max:
1.283 mm
Max: 20.289 mm Max:
4.2540.427
mm mm
Max: 23.448 mmMax: Max:
1.283 mm
Max: 20.287 mmMax: Max:
Y Max: 23.443 mm
Max: 20.278 mmMax: Max:
Max:
4.2540.427
1.283 mm
4.2540.427
mm mm
mm mm
X Max: 23.415 mm
Max: 20.232 mmMax: Max:
Max: 23.287 mmMax: 1.282Max:
1.283 mm
4.2540.427
mm mm
Z Max:
Max: 20.020 mm
Max: 22.679 mmMax: Max:
19.011 mm
Max: 19.433 mm Max: Max:
Max:
4.2530.426
1.281 mm
4.2480.426
mm mm
mm mm
mm
Load 3 : Displacement
Displacement - mm
According to (AS1288-2006)
Allowable Deflection =height/30mm OR 30mm (consider less out of two)
Allowable Deflection =1470/30mm OR 30mm
Allowable Deflection =49mm OR 30mm
Hence allowable deflection =30mm
And here it is max deflection under DL+WL=23mm
Hence Structure is safe.
Print Time/Date: 11/07/2023 15:26 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-23
Pg-24
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 3 : Bending Z
Print Time/Date: 11/07/2023 15:30 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-25
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Load 3 : Bending Z
Moment - kN-m
Print Time/Date: 11/07/2023 15:30 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-26
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X Max: 5.149 kN-m
Z Max: 0 kN-m
Print Time/Date: 11/07/2023 15:31 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-27
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Load 3 : Shear Y
Print Time/Date: 11/07/2023 15:32 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-28
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Max: 0.876 kN
Max:
Max: 0.876
-0.876kN
kN Max:
Max: 0 kN
-0.019
kN kN
Max: Max:0-0.973 kN
Max: -0.876 kN Max: 0
0 kN
kN
Max: 0.019 Max:
kN -1.842 kN
Max: -0.876 kN Max: -0.019
0
0 kN
kN kN
Max: Max: -1.842 kN
Max: -0.876 kN Max: -0.019
0
0 kN
kN kN
Max: Max: -1.842 kN
Max: -0.876 kN Max: -0.019
0
0 kN
kN kN
Max: Max: -1.842 kN
Max: -0.876 kN Max: -0.019
0
0 kN
kN kN
Max: Max: -1.842 kN
Max: -0.876 kN Max: -0.019
0
0 kN
kN kN
Max: Max: -1.842 kN
Max: -0.019
0
0 kN
kN kN
Max: -0.876
0.876 kN Max: 0 kN Max: -1.842 kN
Max: kN Max: -0.019
0 kN kN
Max: Max: -1.842 kN
Max: -0.019
0
0 kN
kN kN
Max: 0.876 kN Max: kN Max:
0 kN
-0.019
Max: 0 kN -1.842 kN
Max: 0.876 kN Max: 0 kN Max:
-0.019 -1.842 kN
kN kN
Y
Max: 0
Max: kN Max:
0 kN
-0.019
Max: 0 kN -1.842 kN
X Max:
Max: 0 kN
kN Max:
Max:0-0.973 kN
-1.842 kN
Load 3 : Shear Y
Force - kN
Print Time/Date: 11/07/2023 15:32 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-29
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Max: 0 kN
Max: -1.842 kN
Print Time/Date: 11/07/2023 15:40 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-30
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-31
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Print Time/Date: 11/07/2023 15:33 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-32
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
0.876
0 kN kN
1.753
0 kN kN
1.753
0 kN kN 0.928
0.909
0 kN kN
0.950 kN
1.753
0 kN kN 0 kN kN -2.728
1.797
1.759 -2.728kN
kN
1.820 kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN -5.456 kN
1.820 kN -5.456 kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.753
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
0.876
0 kN kN 1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
1.797
1.759
0 kN kN
1.820 kN -5.456
-5.456kN
kN
Y 0.928
0.909
0 kN kN
0.950 kN -5.456
-2.728
-2.728kN
-5.456kN
kN
X
kN
Print Time/Date: 11/07/2023 15:33 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-33
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Y
X
Z
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 1
Pg-34
Job No Sheet No Rev
1
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 1 of 5
Pg-35
Job No Sheet No Rev
2
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 2 of 5
Pg-36
Job No Sheet No Rev
3
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 3 of 5
Pg-37
Job No Sheet No Rev
4
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 4 of 5
Pg-38
Job No Sheet No Rev
5
Software licensed to STAAD.Pro Advanced Part
CONNECTED User: Not signed in
Job Title Ref
By Date10-Jul-23 Chd
Print Time/Date: 11/07/2023 15:34 STAAD.Pro CONNECT Edition 22.00.00.15 Print Run 5 of 5
Pg-39
11 July 2023 15:35
PAGE NO. 1
****************************************************
* *
* STAAD.Pro CONNECT Edition *
* Version 22.00.00.15 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= JUL 11, 2023 *
* Time= 14:47:34 *
* *
* Licensed to: only @ ::LAVTeam:: (R) *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\Users\KHALED\Pictures\ALCOSU~1\DAMACC~1\DAMACH~1\DAMAC HAND RAIL.STD
2. START JOB INFORMATION
3. ENGINEER DATE 10-JUL-23
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 2 0 0.25 0; 3 0 1.47 0; 4 2.317 0 0; 5 2.317 0.25 0; 6 2.317 1.47 0
9. 7 4.634 0 0; 8 4.634 0.25 0; 9 4.634 1.47 0; 10 6.951 0 0; 11 6.951 0.25 0
10. 12 6.951 1.47 0; 13 9.268 0 0; 14 9.268 0.25 0; 15 9.268 1.47 0; 16 11.585 0 0
11. 17 11.585 0.25 0; 18 11.585 1.47 0; 19 13.902 0 0; 20 13.902 0.25 0
12. 21 13.902 1.47 0; 22 16.219 0 0; 23 16.219 0.25 0; 24 16.219 1.47 0
13. 25 18.536 0 0; 26 18.536 0.25 0; 27 18.536 1.47 0; 28 20.853 0 0
14. 29 20.853 0.25 0; 30 20.853 1.47 0; 31 23.17 0 0; 32 23.17 0.25 0
15. 33 23.17 1.47 0; 34 25.487 0 0; 35 25.487 0.25 0; 36 25.487 1.47 0
16. 37 27.804 0 0; 38 27.804 0.25 0; 39 27.804 1.47 0; 40 30.121 0 0
17. 41 30.121 0.25 0; 42 30.121 1.47 0; 43 0 0 0.25; 44 2.317 0 0.25
18. 45 4.634 0 0.25; 46 6.951 0 0.25; 47 9.268 0 0.25; 48 11.585 0 0.25
19. 49 13.902 0 0.25; 50 16.219 0 0.25; 51 18.536 0 0.25; 52 20.853 0 0.25
20. 53 23.17 0 0.25; 54 25.487 0 0.25; 55 27.804 0 0.25; 56 30.121 0 0.25
21. MEMBER INCIDENCES
22. 2 2 5; 3 3 6; 5 5 8; 6 6 9; 8 8 11; 9 9 12; 11 11 14; 12 12 15; 14 14 17
23. 15 15 18; 17 17 20; 18 18 21; 20 20 23; 21 21 24; 23 23 26; 24 24 27; 26 26 29
24. 27 27 30; 29 29 32; 30 30 33; 32 32 35; 33 33 36; 35 35 38; 36 36 39; 38 38 41
25. 39 39 42; 40 1 2; 41 2 3; 42 4 5; 43 5 6; 44 7 8; 45 8 9; 46 10 11; 47 11 12
26. 48 13 14; 49 14 15; 50 16 17; 51 17 18; 52 19 20; 53 20 21; 54 22 23; 55 23 24
27. 56 25 26; 57 26 27; 58 28 29; 59 29 30; 60 31 32; 61 32 33; 62 34 35; 63 35 36
28. 64 37 38; 65 38 39; 66 40 41; 67 41 42; 68 40 56; 69 37 55; 70 34 54; 71 31 53
29. 72 28 52; 73 25 51; 74 22 50; 75 19 49; 76 16 48; 77 13 47; 78 10 46; 79 7 45
30. 80 4 44; 81 1 43
31. START GROUP DEFINITION
32. FLOOR
33. _CLADDING-LOAD 2 3 5 6 8 9 11 12 14 15 17 18 20 21 23 24 26 27 29 30 32 33 -
34. 35 36 38 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67
35. _WP 2 3 5 6 8 9 11 12 14 15 17 18 20 21 23 24 26 27 29 30 32 33 35 36 38 39 -
36. 41 43 45 47 49 51 53 55 57 59 61 63 65 67
37. END GROUP DEFINITION
38. DEFINE MATERIAL START
Pg-40
11 July 2023 15:35
Pg-41
11 July 2023 15:35
P R O B L E M S T A T I S T I C S
-----------------------------------
Pg-42
11 July 2023 15:35
SELFWEIGHT Y -1.000
2 0.0002 GY 0.05
2 0.0006 GY 0.12
2 0.0010 GY 0.19
2 0.0014 GY 0.27
2 0.0018 GY 0.34
2 0.0022 GY 0.42
2 0.0026 GY 0.50
2 0.0031 GY 0.57
2 0.0427 GY 0.61 1.71
2 0.0031 GY 1.74
2 0.0026 GY 1.82
2 0.0022 GY 1.90
2 0.0018 GY 1.97
2 0.0014 GY 2.05
2 0.0010 GY 2.12
2 0.0006 GY 2.20
2 0.0002 GY 2.27
43 0.0002 GY 0.05
43 0.0006 GY 0.12
43 0.0010 GY 0.19
43 0.0014 GY 0.27
43 0.0018 GY 0.34
43 0.0022 GY 0.42
43 0.0026 GY 0.50
43 0.0031 GY 0.57
43 0.0031 GY 0.65
43 0.0026 GY 0.72
43 0.0022 GY 0.80
43 0.0018 GY 0.88
43 0.0014 GY 0.95
43 0.0010 GY 1.03
43 0.0006 GY 1.10
43 0.0002 GY 1.17
3 0.0002 GY 0.05
3 0.0006 GY 0.12
3 0.0010 GY 0.19
3 0.0014 GY 0.27
3 0.0018 GY 0.34
3 0.0022 GY 0.42
3 0.0026 GY 0.50
3 0.0031 GY 0.57
3 0.0427 GY 0.61 1.71
Pg-43
11 July 2023 15:35
JT EXT FX/ EXT FY/ EXT FZ/ EXT MX/ EXT MY/ EXT MZ/
INT FX INT FY INT FZ INT MX INT MY INT MZ
SUPPORT=1
43 0.00 0.00 0.00 0.00 0.00 0.00
0.00 -0.00 -2.73 -2.61 0.00 0.00 111111
LOADING- 1. 2.
Pg-44
11 July 2023 15:35
75. PARAMETER 1
76. CODE AISC UNIFIED 2016
77. BEAM 1 ALL
78. FU 410000 ALL
79. FYLD 240000 ALL
80. METHOD LRFD
81. RATIO 1 ALL
82. CHECK CODE ALL
STEEL DESIGN
Pg-45
11 July 2023 15:35
The capacity results and intermediate results in the report follow the notations
and axes labels as defined in the AISC 360-16 code.
The analysis results are reported in STAAD.Pro axis convention and the AISC 360:16
design results are reported in AISC 360-16 code axis convention.
1. Section classification reported is for the cross section and loadcase that
produced the worst case design ratio for flexure/compression Capacity results.
2. Results for any Capacity/Check that is not relevant for a section/loadcase
based on the code clause in AISC 360-16 will not be shown in the report.
3. Bending results are reported as being “about” the relevant axis (X/Y), while
the results for shear are reported as being for shear forces “along” the axis.
E.g : Mx indicates bending about the X axis, while Vx indicates shear along
the X axis.
Pg-46
11 July 2023 15:35
Pg-47
11 July 2023 15:35
Pg-48
11 July 2023 15:35
Pg-49
11 July 2023 15:35
Pg-50
11 July 2023 15:35
Pg-51
11 July 2023 15:35
Pg-52
11 July 2023 15:35
Pg-53
11 July 2023 15:35
Pg-54
11 July 2023 15:35
Pg-55
11 July 2023 15:35
83. PARAMETER 2
84. CODE AISC UNIFIED 2016
85. STEEL TAKE OFF ALL
Pg-56
11 July 2023 15:35
STEEL TAKE-OFF
--------------
86. FINISH
Pg-57
Provide 4xHST3 M16 hilti Anchor Bolt at 85mm effective embedment depth @210mm
spacing to transfer the forces to the concrete.
And Plate Stress must be <275 Mpa
And Here it is safe
Pg-58
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HST3 M16 hef2
Return period (service life in years): 50
Item number: 2105858 HST3 M16x135 35/15
Effective embedment depth: hef = 85.0 mm, hnom = 98.0 mm
Material:
Evaluation Service Report: ETA-98/0001
Issued I Valid: 7/13/2020 | -
Proof: Design Method ETAG (No. 001 Annex C/2010)
Stand-off installation: eb = 0.0 mm (no stand-off); t = 15.0 mm
Anchor plate :
R lx x ly x t = 210.0 mm x 210.0 mm x 15.0 mm; (Recommended plate thickness: 14.0 mm)
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-59
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
3 4
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-60
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
N
NSd £ NRd,s = Rk,s ETAG 001 Annex C, Table 5.2.2.1
gM,s
y c · NRk,p
NSd £ NRd,p = ETAG 001 Annex C, Table 5.2.2.1
gM,p
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-61
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
N
NSd £ NRd,c = Rk,c ETAG 001 Annex C, Table 5.2.2.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N ETAG 001 Annex C, Eq. (5.2)
Ac,N
0 1,5
NRk,c = k1 · √fck,cube · hef ETAG 001 Annex C, Eq. (5.2a)
0
Ac,N = scr,N · scr,N ETAG 001 Annex C, Eq. (5.2b)
c
y s,N = 0.7 + 0.3 · £ 1.00 ETAG 001 Annex C, Eq. (5.2c)
ccr,N
hef
y re,N = 0.5 + 1.00 ETAG 001 Annex C, Eq. (5.2d)
200 £
1
y ec1,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec1,N £
1+
scr,N
1
y ec2,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec2,N £
1+
scr,N
2 0 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm]
103,275 65,025 127.5 255.0
Group anchor ID
1, 3
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-62
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
V
VSd £ VRd,s = Rk,s ETAG 001 Annex C, Table 5.2.3.1
gM,s
V
VSd £ VRd,cp = Rk,cp ETAG 001 Annex C, Table 5.2.3.1
gM,c,p
VRk,cp = k · NRk,c ETAG 001 Annex C, Eq. (5.6)
0 A
NRk,c = NRk,c · 0c,N · y s,N · y re,N · y ec1,N · y ec2,N ETAG 001 Annex C, Eq. (5.2)
Ac,N
0 1,5
NRk,c = k1 · √fck,cube · hef ETAG 001 Annex C, Eq. (5.2a)
0
Ac,N = scr,N · scr,N ETAG 001 Annex C, Eq. (5.2b)
c
y s,N = 0.7 + 0.3 · £ 1.00 ETAG 001 Annex C, Eq. (5.2c)
ccr,N
hef
y re,N = 0.5 + 1.00 ETAG 001 Annex C, Eq. (5.2d)
200 £
1
y ec1,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec1,V £
1+
scr,N
1
y ec2,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec2,V £
1+
scr,N
2 0 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k-factor
164,025 65,025 127.5 255.0 3.410
Group anchor ID
1-4
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-63
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software
considers that the grout is installed under the anchor plate without creating air voids and before application of the loads.
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger
diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-64
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
(1)
Mallée, R.; Riemann, H. (1990): Ankerplattenbefestigungen mit Hinterschnittdübeln,
Bauingenieur 65 (1990), S. 49 - 57, Springer VDI-Verlag, 1990
Mallée, R.; Burkhardt, F. (1999): Befestigungen von Ankerplatten mit Dübeln, Beton und
Stahlbetonbau 94, Heft 12, S. 502 - 511, Ernst & Sohn Verlag, 1999
8.2 Results
Stress distribution s 11
2
193.93 [N/mm ]
2
-88.38 [N/mm ]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Pg-65
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
Stress distribution s 22
2
91.76 [N/mm ]
2
-205.03 [N/mm ]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-66
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
Deformations (z-direction)
0.1 [mm]
-0.1 [mm]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Pg-67
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
9 Installation data
2 2
Anchor plate, steel: S 235; E = 210,000.00 N/mm ; fyk = 235.00 N/mm Anchor type and diameter: HST3 M16 hef2
Profile: Square hollow, 100 x 100 x 3; (L x W x T) = 100.0 mm x 100.0 mm x Item number: 2105858 HST3 M16x135 35/15
3.0 mm
Hole diameter in the fixture: df = 18.0 mm Maximum installation torque: 110 Nm
Plate thickness (input): 15.0 mm Hole diameter in the base material: 16.0 mm
Recommended plate thickness: 14.0 mm Hole depth in the base material: 106.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 160.0 mm
Cleaning: Manual cleaning of the drilled hole according to instructions for use is
required.
Hilti HST3 stud anchor with 98 mm embedment, M16 hef2, Steel galvanized, installation per ETA-98/0001
y
105.0 105.0
30.0
3 4
105.0
150.0
x
105.0
1 2
30.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Pg-68
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 11
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
Pg-69
Hilti PROFIS Engineering 3.0.86
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 12
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 11, 2023 (1) Date: 7/11/2023
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
12
Pg-70
Pg-71
Pg-72
Pg-73
Pg-74
Pg-75
Pg-76
Pg-77