Professional Documents
Culture Documents
Single Point Monitoring
Single Point Monitoring
Product: LDW
Notice
Please carefully read this manual before using products and keep it at where O&M
providers can easily find.
Due to product upgrade and other factors, the content of this manual might change
from time to time. Please take actual product as standard and download latest manual
through www.solarman.cn or sales. Unless otherwise agreed herein, this will only be
used as guidance. Any statement, information or suggestion in this manual will not
take any form of responsibility.
Without written permission, any content of this document (partly or entirely) cannot
be extracted, copied, or transmitted in any form by any company or individual.
LD 1
SOLARMAN 用户手册
Contents
I. Unpacking....................................................................................................................... 3
VII. Commissioning..............................................................................................................42
LD 2
SOLARMAN 用户手册
I. Unpacking
1. Product List
2. Features
Match 35mm standard DIN-rail installation
Ensure the integrity of data
Support remote upgrade and commissioning, make O&M easier
Log device faults, troubleshooting quickly
Send email or message alert to users once there is any problem
Check data via Internet or phone anytime, no software installation needed
LD 3
SOLARMAN 用户手册
Antenna Type A1: 3CM straight rubber antenna; 5: SMA sucker antenna (GPES/3G)
LD 4
SOLARMAN 用户手册
Remote Communication
WiFi / Ethernet
Interface
802.11n: +15dBm(MAX)
RS485 /RS422
Data Interface
RS232(optional)
devices
Signal Light
1 route signal light connecting to the server
LD 5
SOLARMAN 用户手册
5. Hardware Introduction
Interface Usage
Pin header Can be used connecting with female header, can connect
LD 6
SOLARMAN 用户手册
power source(through a 2PIN power port like the green part in the left picture
shown above)
B. Powered by meter:supply the meter via pin header, input voltage is DC 5V~
LD 7
SOLARMAN 用户手册
(2)IO、485/422 Interface
Interfa
ce Network
No. Description Type Function
Numbe Name
r
LD 8
SOLARMAN 用户手册
(3)485
(5) See red circle in the pictures shown below, push upwards if you want to turn it on,
down if you want to turn it off.
LD 9
SOLARMAN 用户手册
(6) Reset Button (see red circle in the pictures shown below)
7. Mechanical Dimension
LD 10
SOLARMAN 用户手册
VSWR ≤1.5
Gain-dBi 2.5dBi
2400-2483MHZ
LD 11
SOLARMAN 用户手册
Tool Usage
1. Wire Cutter
2. Connecting Cable
3. Cable
4. Sucker Antenna
LD 12
SOLARMAN 用户手册
To prevent logger from damages and secure normal operation, installation location
must meet following requirements:
the logger should be installed indoors, and avoid places with humidity, dust,
direct sunlight, corrosive steam; the place should also be shockproof and
pressure-resistant;
Max. communication distance for RS485/422 should be less than 1000 meters,
please ensure the distance from the installed location to the inverter can meet the
communication requirements;
Must stay away from other cabling routes or pipes in the house, e.g. gas pipes,
water pipes, wires etc.
Metal structure can block electromagnetic waves, so the installed position should
be far away from it to ensure devices’ wireless signal quality.
LD 13
SOLARMAN 用户手册
Step 1:Please loosen the black plastic buckle behind din-rail logger and din-rail power
Step 2:Stuck din-rail logger and din-rail power to rail and gently push black buckle upward
Step 3:Gently press to insert the side with pin of din-rail logger to the side with female
header of din-rail power, then press the yellow buckles on two sides of din-rail logger to
Step 4:Connect AB bus of din-rail logger and inverter, A to A, B to B, line order refers to
line order definition mentioned above (if connecting multiple inverters, please cascade
Step 5:Peel of part of rubber outside wire (length depending on actual needs); wind the
exposed mental wire to din-rail power interface LN metal screw nut as the picture shows,
LD 14
SOLARMAN 用户手册
Step 1: Please loosen the black plastic buckle behind din-rail logger and din-rail meter
Step 2:Stuck din-rail logger and din-rail meter to rail and gently push black buckle upward
Step 3:Gently press to insert the side with pin of din-rail logger to the side with female
header of din-rail meter, then press the yellow buckles on two sides of din-rail logger to
Step 4: Connect AB bus of din-rail logger and din-rail meter, A to A, B to B, line order
refers to line order definition mentioned above (if connecting multiple inverters, please
Step 5:Peel of part of rubber outside wire (length depending on actual needs); wind the
exposed mental wire to din-rail power interface LN metal screw nut as the picture shows,
LD 15
SOLARMAN 用户手册
Note:
This manual is based on Windows7 system, for reference only. If the user adopts
other operating systems, please change the settings accordingly.
The stick logger has been embedded into the inverter, you can start to set after
switching on the device.
1. Prepare a computer or device that can connect to a wireless network, e.g. a tablet, smart phone
etc.
LD 16
SOLARMAN 用户手册
LD 17
SOLARMAN 用户手册
LD 18
SOLARMAN 用户手册
LD 19
SOLARMAN 用户手册
Connected successfully
Note:
LD 20
SOLARMAN 用户手册
If you can’t find AP_(logger SN number) in the wireless network list, then there might be
something wrong with logger connections or settings, inverter back cover need to be
opened to check logger connections, please refer to the manual.
Before troubleshooting, please confirm with your inverter manufacturer whether you can
open the inverter back cover yourself. If not, please contact the customer service.
(a) Open the browser, enter ‘10.10.100.254‘, then click enter, enter user name and password
(‘admin’is set as defaulted value)
Note:
Support browser IE 8+,Google browser 15+,Firefox browser 10+
(b) Enter WiFi logger setting interface, you can check all basic info about the logger.
LD 21
SOLARMAN 用户手册
LD 22
SOLARMAN 用户手册
Click ‘refresh’ to search available wireless network, you can also add wireless network manually
LD 23
SOLARMAN 用户手册
LD 24
SOLARMAN 用户手册
Note:
2.SSID of chosen router networks can’t be longer than 30 characters, ‘space’ excluded.
3.When wifi logger is set as STA mode, the range of supported router channel is 1-11.
5.Wifi doesn’t support special characters such as “,”、“;”, it is recommended that users
choose characters like a-z, A-Z, 0-9 as router’s SSID and password, instead of special
8.DHCP function should be enabled on the router, otherwise wifi can’t be connected to
the router;
9.If you still have problems searching signals or connecting to the router, you can try to
restart the router or restore the factory settings, then connect again; If you still have problems,
LD 25
SOLARMAN 用户手册
Note:
Please wait a moment while verifying the password. The following prompt box is displayed if
you put incorrect password or encryption method.
LD 26
SOLARMAN 用户手册
LD 27
SOLARMAN 用户手册
Note: When this dialog box is displayed, check strictly with the following steps.
1.When wifi logger is set as STA mode, the range of supported router channel is 1-11.
3.Wifi doesn’t support special characters such as “,”、“;”, it is recommended that users choose
characters like a-z, A-Z, 0-9 as router’s SSID and password, instead of special characters
like !@#$%&*()_+-=[]\{}|;:'",./<>?
6.DHCP function should be enabled on the router, otherwise wifi can’t connect to the router;
7.If you still have problems searching signals or connecting to the router, you can try to restart
the router or restore the factory settings, then connect again; If you still have problems, please contact
us;
LD 28
SOLARMAN 用户手册
Note:
Most systems support DHCP functions to obtain IP address automatically. If your router
LD 29
SOLARMAN 用户手册
Note
Please encrypt WiFi network in the following ways to improve WiFi security.
Option 1: Select an encryption method to switch AP network and set password, enter the
password next time when you connect the logger, please remember your password.
Option 2: If you choose to change user name and password for the server embedded in data
logger, enter new user name and password next time logging in to the embedded server.
LD 30
SOLARMAN 用户手册
7 Click ‘Complete’,
LD 31
SOLARMAN 用户手册
Note:
Click ‘Complete’ to restart the system immediately, the restart may take 3 minutes, please
wait.
Note: There might be a change in IP address of the device, please refer to steps to
retrieve IP address as above
LD 32
SOLARMAN 用户手册
Once the configuration is complete, please take 3 minutes following the steps
as below, to check whether the configuration is successful:
1. Reconnect logger AP
7. If the signal strength is less than 15%, please try to adjust antenna
direction, and shorten the distance between logger and router.
9 Firmware Upgrade
a. Power on the logger, open wireless network, search logger SN number and then connect
b. Open the browser, enter 10.10.100.254 to log in Wifi logger homepage (user name and
LD 33
SOLARMAN 用户手册
c. Check whether the software version is as required, if yes, no upgrade is needed before next
step; if not, click software upgrade, then click ’select files to upgrade’ to select the program to be
Note:
The logger will restart automatically after upgrade. After the restart, you have to login
configuration interface again. We recommend you to restart after all configurations. Firmware
LD 34
SOLARMAN 用户手册
If the connected inverter type is the current one, the upgrade is successful, if not, change steps as below
LD 35
SOLARMAN 用户手册
c. Click ‘Save’
LD 36
SOLARMAN 用户手册
e. After ‘restarting ’ the logger, check the connecting inverter type in ‘System’, if current
LD 37
SOLARMAN 用户手册
Warning
Open browser and enter SOLARMAN website:
http://pro.solarman.cn
Browser supported: IE8+, Google broswer10+, Firefox browser 9+,
Safari 4+
1. Platform Registration
LD 38
SOLARMAN 用户手册
2. Platform Login
After successful registration, users can enter correct email address and password in
the login interface to enter the management portal.
Note:
1 Type into your account and password if you have your own:
Password:12345678
LD 39
SOLARMAN 用户手册
LD 40
SOLARMAN 用户手册
Warning
If users enter PV monitoring system for the first time within 10 minutes
after successful registration, please check real-time interface as shown
in the picture. If the interface presents any data, it means the logger has
already been connected (as shown below in the picture)
LD 41
SOLARMAN 用户手册
VII. Commissioning
After the logger has been connected to device please check status of LINK light, 485
light, STATUS light and whether there is any data on platform. (There is only one
indicator light for LINK, 485 and STATUS with the logger’s running conditions
indicated by red or green status, please refer to more light status details as below).
Status
485 Light LINK Light STATUS Light Solution
Description
Check the
/ / × Abnormal
power supply
Transmit data
Quick Flashing / on between logger
and device
1.Check
connection
between
logger and
Abnormal
device
connection
off off on 2.Check if
between logger
logger
and device
communicatio
n setting
matches
device
Connected to
logger device. If
Wireless
wireless
abnormal: set
on Flashing on network, it is
network
abnormal; if
again.
Ethernet, it is
normal.
on on on Normal
LD 42
SOLARMAN 用户手册
LD 43
SOLARMAN 用户手册
① ②
③ ④
If you have any question about our products, please contact our Customer Service
Product Type
Logger Serial Number
Inverter Type
Email: customerservice@solarmanpv.com
Website: www.solarmanpv.com
LD 44