LIFTING CAPACITIES: Lifting capacities for various
Maximum Boom Length Lifted Unassisted operating radii are for freely suspended loads and do not exceed Over End of Unblocked Crawlers or 75% of a static tipping load. Capacities based on structural Over Side of Crawlers competence are denoted by an asterisk (*). 200 Ft. Upper boom point capacity for liftcrane service with single part whip line when using drum 2 is 35,800 Lbs. or 55,400 Lbs. with Load block, hook and weight ball on ground at start. two part whip line. When whip line on drum 3 is used, capacity with single part whip line is 30,000 Lbs. or 55,400 Lbs. with two part whip line. In all cases, upper boom point capacities cannot exceed those listed for main boom capacity. Boom Weight of all load blocks, hooks, weight ball, slings, hoist lines, Oper. Boom Point Boom Rad. Ang. Elev. Capacity etc., beneath boom point sheaves, is considered part of main Feet Deg. Feet Pounds boom load. Boom is not to be lowered beyond radii where combined weights are greater than rated capacity. Where no 200 Ft. Boom capacity is shown, operation is not intended or approved. 36 82.5 209.0 721,700 * 38 81.9 208.7 721,700 * OPERATING CONDITIONS: Machine to operate in a 40 81.3 208.3 721,700 * level position on a firm uniformly supporting surface with mast 45 79.9 207.4 664,400 * up. Refer to boom rigging No. A06939 and Wire Rope 50 78.4 206.3 590,100 * Specification chart No. 8510-A. Crane operator judgment must 55 76.9 205.1 529,800 * 60 75.4 203.7 480,000 * be used to allow for dynamic load effects of swinging, hoisting 65 73.9 202.2 438,000 * or lowering, travel, wind conditions, as well as adverse 70 72.4 200.6 402,200 * operating conditions and physical machine depreciation. Refer 75 70.9 198.8 371,400 * to operators manual for operating guidelines. 80 69.4 196.8 344,400 * 85 67.8 194.7 320,700 * MACHINE TRAVEL: Machine to travel on a firm, level 90 66.2 192.5 296,700 95 64.6 190.0 275,300 and uniformly supporting surface and boom within boom angle 100 63.0 187.4 256,300 range shown in capacity chart. Refer to Maximum Allowable 105 61.4 184.6 239,500 Travel Specification chart No. 8511-A. 110 59.7 181.6 224,400 115 58.0 178.5 210,700 OPERATING RADIUS: Operating radius is horizontal 120 56.3 175.1 198,400 distance from axis of rotation to center of vertical hoist line or 125 54.5 171.4 187,200 130 52.7 167.6 176,900 load block. Boom angle is angle between horizontal and 135 50.9 163.4 167,500 centerline of boom butt and inserts, and is an indication of 140 48.9 159.0 158,800 operating radius. In all cases, operating radius shall govern 145 47.0 154.3 150,800 capacity. 150 44.9 149.2 143,300 155 42.8 143.7 136,400 BOOM POINT ELEVATION: Boom point elevation is 160 40.6 137.9 129,900 vertical distance from ground level to centerline of boom point 165 38.3 131.5 123,900 170 35.8 124.5 118,200 shaft. 175 33.2 116.8 112,900 180 30.4 108.3 107,900 MACHINE EQUIPMENT: Machine equipped with 185 27.3 98.7 103,100 38 Ft. 9 in. crawlers, 60 in. treads, 30 Ft. live mast, 190 23.8 87.5 98,600 100 Ft. mast, 16 part boom hoist reeving, boom support straps, 195 19.6 74.0 94,300 528,000 Lb. crane counterweight and 320,000 Lb. carbody counterweight.