Professional Documents
Culture Documents
By Ijaba - Info Lcd-Tv-Repair-Guide-Handbook - 1
By Ijaba - Info Lcd-Tv-Repair-Guide-Handbook - 1
Driver Board
Power Board
Local Key
T con Board
WiFi
Board IR RF Board
2
Repair Method by Symptoms 3-1. No Power Check(Flow Chart)
Voltage OK?
(3.5V)
inserted N
properly
OK? N
Y
Voltage OK? Replace Main B/D
Y ※ (12V,3.5V)
3
Repair Method by Symptoms 3-2. No Power Check(check method)
5 GND 6 GND
7 GND 8 GND
23 N.C 24 Error-out
3.5V • Lamp SCANNING
Model: PWM Dim #2
The “LED” refers only to the type of lighting source used to illuminate the LCD pixels in the television
1. Direct LED: Direct type term refers to televisions that use a full panel of LEDs to illuminate the pixels.
2. Edge LED: Edge LED,means the LEDs that illuminate the pixels are located only on the edges of the set. 4
Repair Method by Symptoms 3-2. No Power Check(Check method)
9 24V 10 24V
11 GND 12 GND
13 12V 14 12V
15 12V 16 24V
3.3V 17 GND 18 GND
19 GND 20 GND
21 GND 22 L/DIMO_VS
Edge LED 23 L/DIM0_MOSI 24 L/DIM0_SCLK
Power Board 18 Pin (Power Board ↔ Main Board)
7 GND 8 GND
9 24V 10 24V
3.5V 11 GND 12 GND
13 12V 14 12V
15 12V 16 24V
5
17 GND 18 GND
Repair Method by Symptoms 3-3. No Power Check(Power Pin Description)
24 ERROR The Inverter or HV signals whether the Lamp Turn-on functions normally
23 NC Null terminals
The CPU automatically adjusts the brightness, based on the wave pattern of
22 P-DIM
elements communicated (for each picture mode)
6
Repair Method by Symptoms 4-1. No Picture Check(Flow Chart)
First of all, Check whether all of cables between board are inserted properly or not.
(Main B/D↔ Power B/D, LVDS Cable, Speaker Cable, IR B/D Cable,,,)
☞Page 10~12
Sound Y Check Back Light Check Power Check
Back light Y Y
No Picture Working whether “On ”or off Board 12V, 3.5V Voltage Replace module
“On”
properly with naked eye line 12V, 3.5V
Case 1
N N N
N End
Repair Power
Board or parts
7
Repair Method by Symptoms 4-2. No Picture Check(Check Power Pin)
3 24V 4 24V
5 GND 6 GND
NC ERROR
12V P-DIM 7 GND 8 GND
12V A-DIM
9 ST-BY(3.5V) 10 ST-BY(3.5V)
12V INV-ON
GND GND 11 ST-BY(3.5V) 12 ST-BY(3.5V)
GND GND
3.5V 3.5V 13 GND 14 GND
3.5V 3.5V
GND GND 15 GND 16 GND
GND GND
17 12V 18 Inverter On/off
24V 24V
ON/OFF 24V 19 12V 20 A-Dim
<LW Series> 21 12V 22 PWM Dim
23 N.C 24 Error-out
<LK Series>
(only Lamp
SCANNING Model
: PWM Dim #2)
8
Repair Method by Symptoms 4-2. No Picture Check(Check Power Pin)
Screen (LM)
<Check power On(3.3V) and DC 24V, 12V, 3.5V>
Direct LED Check the DC 24V, 12V, 3.5V
Power Board
24 Pin (Power Board ↔ Main Board) - 공통
1 Power on(3.3V) 2 24V
3 24V 4 24V
5 GND 6 GND
7 GND 8 GND
9 ST-BY(3.5V) 10 ST-BY(3.5V)
13 GND 14 GND
15 GND 16 N.C
(Only LPB : V-sync)
19 12V 20 N.C
(LPB, Lamp : A-dim)
23 N.C 24 Error-out
(only Lamp
SCANNING Model
: PWM Dim #2)
12V
3.5V
9
Repair Method by Symptoms 4-2. No Picture Check(Check Power Pin)
Screen (LA)
<Check power input voltage and DC 24V, 12V, 3.5V>
Direct LED 24 Pin (Power Board ↔ Main Board) 18 Pin (Power Board ↔ Main Board)
Power Board
1 Power on 2 Inverter On/off 1 Power on 2 Inverter On/off
19 GND 20 GND
21 GND 22 L/DIMO_VS
23 L/DIM0_MOSI 24 L/DIM0_SCLK
10
Repair Method by Symptoms 4-3. No Picture Check(Check LED Driver 24V )
Direct LED
P202 P203
Power Board
11 Error
14 P-dim
11
Repair Method by Symptoms 5-1. No Sount Check(Flow Chart)
☞Page 15~16
Check Check Y
Speaker N Check audio B+ 24V
No sound User menu Voltage
Off of Power Board
speaker off (24V)
Y N
Check Speaker N
Disconnection Replace main Board End
Cable
Disconnection
Replace Speaker
12
Repair Method by Symptoms 5-2. No Sount Check(Troubleshooting)
13
Repair Method by Symptoms 6. Picture Error Check(Flow Chart)
Replace
Module
☞ Page 31 N
Check color condition by input Check external
-External Input Screen Y Y Check and N
device Screen Screen
-Component OK? Good? replace Link Replace Main B/D
connection OK? OK?
-RGB Cable
condition
-HDMI/DVI
N N Y Y
14
Repair Method by Symptoms 7-1. Sysmptoms List(Main Board)
15
Repair Method by Symptoms 7-1. Sysmptoms List(Main Board)
Main
IC No sound No sound due to a poor feature in Audio IC
B/D
16
Repair Method by Symptoms 7-1. Sysmptoms List(Main Board)
17
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
18
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
19
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
20
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
Alien materials
Module Panel Moisture inflow into the product
inside
Processing
Processi Shipment With the Shipment setting inapplicable,
failure
ng failure setting failure Shipment is made only in a control mode
21
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
T-Con Picture
EOS Poor features in T-CON
B/D distortion
22
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
23
Repair Method by Symptoms 7-2. Sysmptoms List(Module)
24
Repair Method by Symptoms 7-3. Sysmptoms List(LVDS Cable)
25
Repair Method by Symptoms 7-3. Sysmptoms List(FFC Cable, Cabinet, etc)
Vibration and
Speakers shaking from some damage in
Cabinet Damage noise in
the Cabinet Speaker Boss
Speaker System
26
Repair Method by Parts 8. Main Board Check (Symptoms)
Picture Smear
27
Repair Method by Parts 8. Main Board Check (One-Point Repair)
Color smearing
28
Repair Method by Parts 8. Main Board Check (One-Point Repair)
1.Press Button ‘In-Start Mode’ Key 1.If there are “POWER_OFF_BY_NO_ POLLING” message
2.Enter ‘Power Off Status’
2. Replace the main board
*POWER_OFF_BY_NO_POLLING
:If there are no communications between micom and Host
CPU for 15second
→ Micom will reboot all system
29
Repair Method by Parts 9. Module Check(One Point Repair)
Upon an abnormal voltage, open and re-check the FFC leading from T-CON to the Module.
Upon recurrence of a same failure, change T-CON or the Module if the voltage is normal.
(Refer to below Normal Voltage)
T-Con Board P VCC
VDD
VCC
VGL
VGH
30
Repair Method by Parts 9. Module Check(One Point Repair)
1.Title: No Display (Only BackLight) * P-VCC: A standard voltage to activate the LCD
VCC: Usually 3.3V power required to activate Digital IC
- Sound Normal/CH Volume Control Normally VDD: A voltage supplied to Source Drive IC for activation of LCD
VGL/VGH: Voltages required to turn TFT Gate on/off
2.Applied to: LW9500, LW9600, andLW9800 -VGL: TFT Gate on
-VGH:TFT Gate off
3. Troubleshooting:
Check if Back Light is ON and, if it’s ON, re-check T-CON as the following sequence.
Change the Module if the voltage is normal. Change T-CON if voltage abnormal.
P701 VDD
VCC
P VCC
VGH VG
L
31
Repair Method by Parts 10-1. Wi-Fi Check(Flow Chart)
Check the Wi-Fi Mac value Check the Wifi wafer Normal
N N Replace
is “NG”? Voltage
INSTART menu Pin no.1 Main B/D
3.3V
Y Y
Pin map
Wi-Fi Mac value N
is “NG”? Close
PIN USB interface
Y 1 Vcc(3.3V)
4 GND
5 WOW
6 NC
32
Repair Method by Parts 10-2. Wi-Fi Check(One Point Repair)
33
Repair Method by Parts 11. Camera Check(Flow Chart/Troubleshooting)
Check
Check the Camera Ver. N Check the Camera wafer N Replace
Voltage
INSTART menu is “NG”? P4200 (pin no.2) Main B/D
(3.3V)
Y Y
Camera Ver. N
is “NG”? Close
Change the
Camera assy
34
Repair Method by Parts 12-1. Magic Remote Check(Flow Chart)
N Y Press the
Y wheel
35
Repair Method by Parts 12-2. Magic Remote Check(Pairing/Un Pairing)
RF Pairing/Un-Pairing Method
Method Description
36
Repair Method by Parts 12-3. Magic Remote Check(Register/Unregister)
Replace
Main B/D
☞Page 52~55 ☞Page 52~55 ☞Page 52~55
Check R/C itself Y Check & Repair N Y Y
Operating Check B+ 3.5V Check IR Normal
Operation Cable connection Operating Voltage Signal?
OK? OK? On Main B/D OK? Output signal
Connector solder
N
Y N N
☞Page 10~12
Check R/C Operating Check & Replace Close Check 3.5v on Power B/D
When turn off light Baterry of R/C Replace Power B/D or
in room Replace Main B/D Repair/Replace
(Power B/D don’t have problem) IR B/D
Y
If R/C operate,
Operating Close
Explain the customer
OK?
cause is interference
from light in room. N
Replace R/C
38
Repair Method by Parts 13-2. Remote Control Check(Troubleshooting)
Main Board
P4101
1 GND
2 KEY1
3 KEY2
③ 4 +3.5V_ST
5 GND
6 LOGO/LED_R
④ 7 IR
8 GND
②
39
Repair Method by Parts 13-2. Remote Control Check(Troubleshooting)
<LM Series>
P4800
Main Board
③ 1 3.3V
2 GND
3 RX
4 TX
5 RESET
6 DC
7 DD
8 GND
Checking order
1, 2. Check Motion cable condition between Motion assy & Main board.
3. Check the 3.3V on the pin no. 1.
40
Repair Method by Parts 13-2. Remote Control Check(Troubleshooting)
<LA Series>
P4002
Main Board 1 GND
2 KEY1
3 KEY2
③ 4 +3.5V_ST
5 GND
6 LED
7 +3.5V_ST
8 GND
④
①
②
Checking order
1, 2. Check IR cable condition between IR & Main board.
3. Check the st-by 3.5V on the pin no 4,7.
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog
Tester needle moves slowly, and defective when it does not move at all.
41
Adjustments method after Repair 16. Tool option setting method after main B/D change
(adjustment RGB Pattern)
Step 1. Check full model name of your TV(Select one) Step 2. Upgrade TV
a. Check a label on TV(Side or Rear) a. Make a folder “LG_DTV” on USB drive
b. Save the software in “LG_DTV” folder. Make sure file is unzipped before placing in Folder
c. Insert USB memory drive into USB port on TV
Note)
If current software on TV is same with or newer than
That on USB drive, TV software Upgrade menu won’t be opend
(Some USB memory devices may not be compatible with TV)
Category
□ Leadership □ Marketing □ Sales ■ CS
□ Manufacturing □ Quality □ Biz. administration
Published on 04/01/2014
Updated on 11/02/2014
※ No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying, recording, or by any information storage or retrieval system without written permission from LGE.