Professional Documents
Culture Documents
Cerafil (Filters/Traps/Discriminators) For Audio/Visual Equipment
Cerafil (Filters/Traps/Discriminators) For Audio/Visual Equipment
Cerafil (Filters/Traps/Discriminators) For Audio/Visual Equipment
(Filters/Traps/Discriminators)
for Audio/Visual Equipment
Cat.No.P50E-6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
EU RoHS Compliant
s All the products in this catalog comply with EU RoHS.
s EU RoHS is "the European Directive 2011/65/EU on the Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment."
s For more details, please refer to our website 'Murata's Approach for EU RoHS'
(http://www.murata.com/info/rohs.html).
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2
Part Numbering 2
1. CERAFILr
1-1 CERAFILr 10.7MHz 3
1 Small Chip Type SFECF Series 5
2 Chip Type SFECV/SFECK Series 11 4
3 Standard Lead Type SFELF Series 14
4 Low Loss Type SFELF Series 17
5
5 Low Spurious Response Type SFELF Series 20
6 Wide Bandwidth Type SFELF Series 23
6
7 Narrow Bandwidth Type SFELF Series 25
8 For FM-IF Tuners SFELF Series 27
Related Data on Lead Type 30 7
1-2 CERAFILr 2.3-6.5MHz
9 4.5-6.5MHz Chip Type SFSKA Series 31 8
10 2.3-5.7MHz Chip Type SFSKB Series 34
1-3 CERAFILr 455kHz
9
11 Chip Type SFPKA Series 38
12 Lead Type SFPLA/CFWLA Series 40
10
13 For AM Stereo Wide Bandwidth Type SFPLA/CFWLA/CFULA Series 42
SFp Series Temperature Characteristics 44
2. Ceramic Trap 11
14 Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series 45
3. Ceramic Discriminator 12
15 10.7MHz Ultra Thin Chip Type CDSCB Series 47
Applied IC Reference Table 52
13
Notice 53
Packaging 69
14
Part Number Index 74
15
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
o Part Numbering
CERAFILr for FM
Code Series
rNominal Center Frequency A0 Two-digit alphanumerics express series
Expressed by four-digit alphanumerics. The unit is in hertz (Hz).
Decimal point is expressed by capital letter "M" in case of MHz. iPackaging
Code Packaging
t3dB Bandwidth -B0 Bulk
Code 3dB Bandwidth -R0 Embossed Taping ø180mm
C 450kHz min -R1 Embossed Taping ø330mm
D 350kHz min -A0 1500pcs. /Radial Taping H0=18mm
E 330kHz -A1 1000pcs. /Radial Taping H0=18mm
F 280kHz Radial taping is applied to lead type and embossed taping to chip type.
With non-standard products, two-digit alphanumerics indicating
G 230kHz
"Individual Specification" are added between "uSeries" and
H 180kHz "iPackaging."
J 150kHz
K 110kHz
L 80kHz
M 50kHz
N 35kHz
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
CERAFILr
Code Packaging
rNominal Center Frequency -B0 Bulk
Expressed by four-digit alphanumerics. The unit is in hertz (Hz). -R1 Embossed Taping ø=330mm
Decimal point is expressed by capital letter "M" in case of MHz.
With non-standard products, two-digit alphanumerics indicating
"Individual Specification" is added between "yProduct Specification
Code (2)" and "uPackaging."
CERAFILr for AM
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Traps
Discriminators for FM
Code IC
tSeries 001 Applicable IC Control Code
Code Series
G Two-digit alphanumerics express series iPackaging
Code Packaging
-B0 Bulk
-A0 Radial Taping H0=18mm
-R0 Embossed Taping ø=180mm
-R1 Embossed Taping ø=330mm
Radial taping is applied to lead type and embossed taping to chip type.
With non-standard products, an alphanumerics indicating "Individual
Specification" is added between "uIC" and "iPackaging."
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
3.45±0.2 1.3±0.1
3.1±0.2
high-performance and super thin (1.4mm max.) filters. Input electrode
marker
The piezoelectric element is sandwiched by the ceramic
0 to 0.4 (0.6) (0.6) (0.6) 0 to 0.4
substrate. They have 1.4mm max. thickness and a small
mounting area (3.45x3.1mm). SFECF series and
(1.28)(1.28)
CDSCB series (MHz Discriminator) enable customers to 0.3 min. 0.3 min.
0.65±0.3 0.7±0.3 0.65±0.3
make VICS/RKE/TPMS set very thin and small.
0.85±0.3 0.85±0.3
(1): Input
(1) (2) (3) (2)(5): Ground
(3)(4): No connection
0.75±0.3
(6) (5) (4)
c Features (6): Output
: EIAJ Monthly Code
1. The filters are mountable by automatic placers. (1.28)(1.28) ( ): Reference
Standard Type
Center Nominal Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output
Part Number Frequency Frequency (fn) Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm)
10.700 30 min. 30 min.
SFECF10M7HA00-R0 - 180 ±40kHz 470 max. 4.0±2.0dB 1.0 max. 330
±30kHz [within 9MHz to fo] [within fo to 12MHz]
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
High-Reliability Type
1
Center Nominal Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output
Part Number Frequency Frequency (fn) Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm)
10.700 30 min. 30 min.
SFECF10M7HA00S0-R0 - 180 ±40kHz 470 max. 4.0±2.0dB 1.0 max. 330
±30kHz [within 9MHz to fo] [within fo to 12MHz]
(3) (4)
1.05
R1
0.3
1.40
(1) (6)
Rg
0.1
RF
0.3
E1 C2
R2 E2 Voltmeter
1.05
0.1
0.1
(1): Input
(2)(5): Ground
0.8 0.6 0.8 0.6 0.8 (3)(4): No connection
Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5%
(1): Input
(6): Output C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance (2)(5): Ground
of RF voltmeter) (3)(4): No connection
It indicates solder resist land pattern. (in mm) E1: S.S.G. Output Voltage (6): Output
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 6.0 1 6.0
2 5.0 2 5.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 4.0 3 4.0
4 3.0 4 3.0
5 2.0 5 2.0
6 1.0 6 1.0
7 0.0 7 0.0
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
SFECF10M7FA00-R0/SFECF10M7FF00-R0 SFECF10M7EA00-R0
0 7.0 0 7.0
1 6.0 1 6.0
2 5.0 2 5.0
Attenuation (dB)
G.D.T. (μsec.)
Attenuation (dB)
G.D.T. (μsec.)
3 4.0 3 4.0
4 3.0 4 3.0
5 2.0 5 2.0
6 1.0 6 1.0
7 0.0 7 0.0
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
SFECF10M7DA0001-R0 SFECF10M7DF00-R0
0 7.0 0 7.0
1 6.0 1 6.0
2 5.0 2 5.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 4.0 3 4.0
4 3.0 4 3.0
5 2.0 5 2.0
6 1.0 6 1.0
7 0.0 7 0.0
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 6.0 1 6.0
2 5.0 2 5.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 4.0 3 4.0
4 3.0 4 3.0
5 2.0 5 2.0
6 1.0 6 1.0
7 0.0 7 0.0
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
SFECF10M7FA00S0-R0/SFECF10M7FF00S0-R0 SFECF10M7EA00S0-R0
0 7.0 0 7.0
1 6.0 1 6.0
2 5.0 2 5.0
Attenuation (dB)
G.D.T. (μsec.)
Attenuation (dB)
G.D.T. (μsec.)
3 4.0 3 4.0
4 3.0 4 3.0
5 2.0 5 2.0
6 1.0 6 1.0
7 0.0 7 0.0
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
SFECF10M7DF00S0-R0
0 7.0
1 6.0
2 5.0
Attenuation (dB)
G.D.T. (μsec.)
3 4.0
4 3.0
5 2.0
6 1.0
7 0.0
10.300 10.500 10.700 10.900 11.100
Frequency (MHz)
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFECF10M7FA00-R0/SFECF10M7FF00-R0 SFECF10M7EA00-R0
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFECF10M7DA0001-R0/SFECF10M7DF00-R0
0
10
20
Attenuation (dB)
30
40
50
60
70
8.700 9.700 10.700 11.700 12.700
Frequency (MHz)
9
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFECF10M7FA00S0-R0/SFECF10M7FF00S0-R0 SFECF10M7EA00S0-R0
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFECF10M7DF00S0-R0
0
10
20
Attenuation (dB)
30
40
50
60
70
8.700 9.700 10.700 11.700 12.700
Frequency (MHz)
10
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2.9±0.3
∗ ∗
∗
customers to make an AM/FM set very thin, and it can be
useful to the total chip circuit. (3) (2) (1)
c Features
1.5±0.2
: Marking
(1) : Input
1. The piezoelectric element is sandwiched by heat (2) : Ground
(3) : Output
resistant substrate, thus it has excellent mechanical 1.0±0.5 1.0±0.5 1.0±0.5
c Applications
1. Small, thin radios
2. Automotive radios
3. Headphone stereos
Standard Type
Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output
Part Number Frequency Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm)
15.000 30 min. 30 min.
SFECV15M0EQ0001-R0 300 min. 750 max. 7.0max. 1.0 max. 330
±50kHz [within 14MHz to fo] [within fo to 16MHz]
High-Reliability Type
Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output
Part Number Frequency Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm)
10.700 35 min. 35 min.
SFECK10M7KA00S0-R0 110 ±30kHz 320 max. 6.0±2.0dB 1.0 max. 330
±30kHz [within 9MHz to fo] [within fo to 12MHz]
11
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
R1 (1) (3)
(2)
Rg
4.0
E1 RF
R2 C2 E2 Voltmeter
S.S.G.
=-10dBm
1.65 1.65
2.85 2.85
1 6.5
2 8.0
2 6.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
4 6.0
3 5.5
4 5.0
6 4.0
5 4.5
8 2.0
6 4.0
10 0.0 7 3.5
14.700 14.800 14.900 15.000 15.100 15.200 15.300 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
SFECV10M7JA00-R0
0 8.0
1 7.5
2 7.0
Attenuation (dB)
G.D.T. (μsec.)
3 6.5
4 6.0
5 5.5
6 5.0
7 4.5
10.300 10.500 10.700 10.900 11.100
Frequency (MHz)
12
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 6.5 1 7.5
2 6.0 2 7.0 2
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 5.5 3 6.5
4 5.0 4 6.0
5 4.5 5 5.5
6 4.0 6 5.0
7 3.5 7 4.5
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
10
10
20
20
Attenuation (dB)
30
Attenuation (dB)
30
40
40
50
50
60
60
70
70
80 8.700 9.700 10.700 11.700 12.700
13.000 14.000 15.000 16.000 17.000 Frequency (MHz)
Frequency (MHz)
SFECV10M7JA00-R0
0
10
20
Attenuation (dB)
30
40
50
60
70
8.700 9.700 10.700 11.700 12.700
Frequency (MHz)
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
13
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±2.0
EIAJ
of the piezoelectric ceramic. CODE
5.0±1.0
inside of the ceramic filter contain no lead (Pb). 0.5±0.1
0.3±0.1
(1) : Input
1. These miniature filters have high mechanical SFELF10M7HA00-B0 (2) : Ground
3.0±1.0
(3) : Output
strength. (in mm)
(3) (2) (1)
2. Low loss, favorable waveform symmetry, and high
selectivity
7.0±2.0
3. Various bandwidths are available for applications
in wide to narrow bands.
MARKING
4. Small dispersion and stable characteristics
7.0±2.0
EIAJ
5. Change in center frequency is typically within CODE
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
SFELF10M7GA00-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
7.0±2.0
MARKING
7.0±2.0
EIAJ
CODE
1.38±0.2
1.7±0.1
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
SFELF10M7FA00-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
14
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Rg RF
C Voltmeter
R2
S.S.G
c Frequency Characteristics
SFELF10M7HA00-B0 SFELF10M7GA00-B0
0 6.5 0 6.0
1 6.0 1 5.5
2 5.5 2 5.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 5.0 3 4.5
4 4.5 4 4.0
5 4.0 5 3.5
6 3.5 6 3.0
7 3.0 7 2.5
10.500 10.600 10.700 10.800 10.900 10.500 10.600 10.700 10.800 10.900
Frequency (MHz) Frequency (MHz)
SFELF10M7FA00-B0
0 5.5
1 5.0
2 4.5
Attenuation (dB)
G.D.T. (μsec.)
3 4.0
4 3.5
5 3.0
6 2.5
7 2.0
10.500 10.600 10.700 10.800 10.900
Frequency (MHz)
15
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
3 50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFELF10M7FA00-B0
0
10
20
Attenuation (dB)
30
40
50
60
70
8.700 9.700 10.700 11.700 12.700
Frequency (MHz)
16
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±2.0
EIAJ
of the piezoelectric ceramic. CODE
5.0±1.0
inside of the ceramic filter contain no lead (Pb). 0.5±0.1
0.3±0.1
(1) : Input
1. Insertion loss is 1 to 1.5dB lower than SFELF10M7JAA0-B0 (2) : Ground
3.0±1.0
(3) : Output
conventional products. These types are useful for (in mm)
(3) (2) (1)
elevating the sensitivity of sets.
2. Small dispersion and stable characteristics
7.0±2.0
3. Excellent shape factor of frequency response
4. Good waveform symmetry
MARKING
7.0±2.0
EIAJ
CODE
1.38±0.2
1.7±0.1
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
SFELF10M7HAA0-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
7.0±2.0 7.0±2.0
MARKING MARKING
7.0±2.0
7.0±2.0
EIAJ EIAJ
CODE CODE
1.38±0.2 1.38±0.2
1.7±0.1 1.7±0.1
5.0±1.0
5.0±1.0
0.5±0.1 0.5±0.1
0.3±0.1
3.0±1.0
17
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
Rg RF
C Voltmeter
R2
S.S.G
c Frequency Characteristics
SFELF10M7JAA0-B0 SFELF10M7HAA0-B0
0 7.0 0 6.5
1 6.5 1 6.0
2 6.0 2 5.5
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 5.5 3 5.0
4 5.0 4 4.5
5 4.5 5 4.0
6 4.0 6 3.5
7 3.5 7 3.0
10.500 10.600 10.700 10.800 10.900 10.500 10.600 10.700 10.800 10.900
Frequency (MHz) Frequency (MHz)
SFELF10M7GAA0-B0 SFELF10M7FAA0-B0
0 6.0 0 5.5
1 5.5 1 5.0
2 5.0 2 4.5
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 4.5 3 4.0
4 4.0 4 3.5
5 3.5 5 3.0
6 3.0 6 2.5
7 2.5 7 2.0
10.500 10.600 10.700 10.800 10.900 10.500 10.600 10.700 10.800 10.900
Frequency (MHz) Frequency (MHz)
18
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700
Frequency (MHz)
11.700 12.700 8.700 9.700 10.700
Frequency (MHz)
11.700 12.700
4
SFELF10M7GAA0-B0 SFELF10M7FAA0-B0
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
19
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±2.0
EIAJ
of the piezoelectric ceramic. CODE
5.0±1.0
inside of the ceramic filter contain no lead (Pb). 0.5±0.1
2.5±0.2 2.5±0.2
c Features
0.3±0.1
These types have lower spurious response compared SFELF10M7KAB0-B0
3.0±1.0
5 to standard filters.
(3) (2) (1) (in mm)
7.5±2.0 7.5±2.0
MARKING MARKING
7.0±2.0
7.0±2.0
EIAJ EIAJ
CODE CODE
1.38±0.2 1.38±0.2
1.7±0.1 1.7±0.1
5.0±1.0
5.0±1.0
0.5±0.1 0.5±0.1
0.3±0.1
SFELF10M7JAB0-B0 SFELF10M7HAB0-B0
3.0±1.0
3.0±1.0
(3) (2) (1) (in mm) (3) (2) (1) (in mm)
7.5±2.0 7.5±2.0
MARKING MARKING
7.0±2.0
7.0±2.0
EIAJ EIAJ
CODE CODE
1.38±0.2 1.38±0.2
1.7±0.1 1.7±0.1
5.0±1.0
5.0±1.0
0.5±0.1 0.5±0.1
0.3±0.1
SFELF10M7GAB0-B0 SFELF10M7FAB0-B0
3.0±1.0
3.0±1.0
(3) (2) (1) (in mm) (3) (2) (1) (in mm)
20
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
(1) (2) (3)
R1
Rg RF
C Voltmeter
R2
S.S.G
c Frequency Characteristics
SFELF10M7KAB0-B0 SFELF10M7JAB0-B0
0 8.0 0 7.0
1 7.5 1 6.5
2 7.0 2 6.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 6.5 3 5.5
4 6.0 4 5.0
5 5.5 5 4.5
6 5.0 6 4.0
7 4.5 7 3.5
10.500 10.600 10.700 10.800 10.900 10.500 10.600 10.700 10.800 10.900
Frequency (MHz) Frequency (MHz)
SFELF10M7HAB0-B0 SFELF10M7GAB0-B0
0 6.5 0 6.0
1 6.0 1 5.5
2 5.5 2 5.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 5.0 3 4.5
4 4.5 4 4.0
5 4.0 5 3.5
6 3.5 6 3.0
7 3.0 7 2.5
10.500 10.600 10.700 10.800 10.900 10.500 10.600 10.700 10.800 10.900
Frequency (MHz) Frequency (MHz)
Continued on the following page.
21
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Frequency Characteristics
SFELF10M7FAB0-B0
0 5.5
1 5.0
2 4.5
Attenuation (dB)
G.D.T. (μsec.)
3 4.0
4 3.5
5 3.0
6 2.5
7 2.0
10.500 10.600 10.700 10.800 10.900
Frequency (MHz)
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFELF10M7HAB0-B0 SFELF10M7GAB0-B0
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFELF10M7FAB0-B0
0
10
20
Attenuation (dB)
30
40
50
60
70
8.700 9.700 10.700 11.700 12.700
Frequency (MHz)
22
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±2.0
EIAJ
of the piezoelectric ceramic. CODE
5.0±1.0
inside of the ceramic filter contain no lead (Pb). 0.5±0.1
0.3±0.1
(1) : Input
Realizes wider band characteristics not obtained by SFELF10M7EA00-B0 (2) : Ground
3.0±1.0
(3) : Output
conventional ceramic filters. (in mm)
(3) (2) (1)
7.0±2.0
6
MARKING
7.0±2.0
EIAJ
CODE
1.38±0.2
1.7±0.1
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
SFELF10M7DF00-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
Center Nominal Center 3dB Attenuation Insertion Loss Spurious Spurious Input/Output
Part Number Frequency Frequency (fn) Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (MHz) (kHz) (kHz) (dB) (1) (dB) (2) (dB) (ohm)
10.700 30 min. 30 min.
SFELF10M7EA00-B0 - 330 ±50kHz 680 max. 4.0±2.0dB 330
±30kHz [within 9MHz to fo] [within fo to 12MHz]
20 min. 20 min.
SFELF10M7DF00-B0 - 10.700 fn±175 min. 950 max. 3.0±2.0dB 470
[within 5MHz to fn] [within fn to 15MHz]
Area of Attenuation: [within 20dB]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
23
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
Rg RF
C Voltmeter
R2
S.S.G
c Frequency Characteristics
SFELF10M7EA00-B0 SFELF10M7DF00-B0
0 4.5 0 4.5
1 4.0 1 4.0
2 3.5 2 3.5
6
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 3.0 3 3.0
4 2.5 4 2.5
5 2.0 5 2.0
6 1.5 6 1.5
7 1.0 7 1.0
10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100
Frequency (MHz) Frequency (MHz)
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
24
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Features
MARKING
SFELF10M7LFTA/KAH0 series realizes narrower band
7.0±2.0
EIAJ
characteristics not obtained by conventional ceramic CODE
5.0±1.0
European car-audio or AM upconversion use that 0.5±0.1
needs stable narrow band characteristics.
As part of the environment protection program, the solder 2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
for terminal plating and terminal-element connection SFELF10M7LFTA-B0 (2) : Ground
3.0±1.0
(3) : Output
inside of the ceramic filter contain no lead (Pb). (in mm)
(3) (2) (1)
7.0±2.0
MARKING
7.0±2.0
EIAJ
CODE
1.38±0.2
7
1.7±0.1
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
SFELF10M7KAH0-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
Center Nominal Center 3dB Attenuation Insertion Loss Spurious Spurious Input/Output
Part Number Frequency Frequency (fn) Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (MHz) (kHz) (kHz) (dB) (1) (dB) (2) (dB) (ohm)
30 min. 30 min.
SFELF10M7LFTA-B0 - 10.700 fn±25 min. 280 max. 7.0±2.0dB 330
[within 9MHz to fn] [within fn to 12MHz]
25
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
Rg RF
C Voltmeter
R2
S.S.G
c Frequency Characteristics
SFELF10M7LFTA-B0 SFELF10M7KAH0-B0
0 12.0 0 8.0
1 11.0 1 7.5
2 10.0 2 7.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 9.0 3 6.5
4 8.0 4 6.0
5 7.0 5 5.5
7 6.0 5.0
6 6
7 5.0 7 4.5
10.600 10.650 10.700 10.750 10.800 10.600 10.650 10.700 10.750 10.800
Frequency (MHz) Frequency (MHz)
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
26
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±2.0
EIAJ
of the piezoelectric ceramic. CODE
5.0±1.0
inside of the ceramic filter contain no lead (Pb). 0.5±0.1
0.3±0.1
(1) : Input
1. Little dispersion of amplitude characteristics and SFELF10M7HA0G-B0 (2) : Ground
3.0±1.0
(3) : Output
phase characteristics (G. D. T. characteristics) (in mm)
(3) (2) (1)
2. The SFELF_G series is based on SFELF_FA00/GA00/
HA00, and it obtains high selectivity with low loss.
7.0±2.0
There is little dispersion of amplitude and GDT
characteristics, and low distortion rate can be
MARKING
obtained.
7.0±2.0
EIAJ
3. The flatness of GDT is inspected for all products. CODE
1.38±0.2
1.7±0.1
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
8
0.3±0.1
(1) : Input
SFELF10M7GA0G-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
7.0±2.0
MARKING
7.0±2.0
EIAJ
CODE
1.38±0.2
1.7±0.1
5.0±1.0
0.5±0.1
2.5±0.2 2.5±0.2
0.3±0.1
(1) : Input
SFELF10M7FA0G-B0 (2) : Ground
3.0±1.0
(3) : Output
(in mm)
(3) (2) (1)
Center 3dB Attenuation Insertion Loss Spurious Spurious GDT Bandwidth Input/Output
Part Number Frequency Bandwidth Attenuation Attenuation Impedance
(fo) (MHz) (kHz) (kHz) (dB) (1) (dB) (2) (dB) (kHz) (ohm)
10.700 40 min. 40 min.
SFELF10M7HA0G-B0 180 ±40kHz 520 max. 7.0max. fo±45min. 330
±30kHz [within 9MHz to fo] [within fo to 12MHz]
27
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
Rg RF
C Voltmeter
R2
S.S.G
c Frequency Characteristics
SFELF10M7HA0G-B0 SFELF10M7GA0G-B0
0 6.5 0 6.0
8 1 6.0 1 5.5
2 5.5 2 5.0
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
3 5.0 3 4.5
4 4.5 4 4.0
5 4.0 5 3.5
6 3.5 6 3.0
7 3.0 7 2.5
10.400 10.500 10.600 10.700 10.800 10.900 11.000 10.400 10.500 10.600 10.700 10.800 10.900 11.000
Frequency (MHz) Frequency (MHz)
SFELF10M7FA0G-B0
0 5.5
1 5.0
2 4.5
Attenuation (dB)
G.D.T. (μsec.)
3 4.0
4 3.5
5 3.0
6 2.5
7 2.0
10.400 10.500 10.600 10.700 10.800 10.900 11.000
Frequency (MHz)
28
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700
Frequency (MHz) Frequency (MHz)
SFELF10M7FA0G-B0
0
10
20
Attenuation (dB)
30
40
50
60
70
8.700 9.700 10.700 11.700 12.700
Frequency (MHz)
29
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Temperature Characteristics
SFELF10M7GA00-B0 SFELF10M7HA00-B0
+40 +40
Variation (kHz)
Variation (kHz)
Center frequency Center frequency
+20 +20
0 0
–20 –20
–40 –40
–20 0 +20 +40 +60 +80 –20 0 +20 +40 +60 +80
+2 Temperature (°C) +2 Temperature (°C)
Variation (dB)
Insertion loss
Variation (dB)
Insertion loss
+1 +1
0 0
–1 –1
–2 –2
–20 0 +20 +40 +60 +80 –20 0 +20 +40 +60 +80
+40 Temperature (°C) +40 Temperature (°C)
Variation (kHz)
Variation (kHz)
3dB Bandwidth 3dB Bandwidth
+20 +20
0 0
–20 –20
–40 –40
–20 0 +20 +40 +60 +80 –20 0 +20 +40 +60 +80
Temperature (°C) Temperature (°C)
c Matching Conditions
1. When using ceramic filters, it is most important to 3. The SFELF10M7 series are of input/output symmetric
match the input/output load to impedance 330 ohm structure so that in theory there is no input/output
(SFELF10M7DF00-B0 is 470 ohm). directionality. Actual circuits may use different
Waveform symmetry is damaged when reactance is input/output loading conditions (for example,
added to the input/output load. mismatched impedance) or capacitance load. In such
2. Two ceramic filters directly connected can be used cases, the waveform will be a little changed by the
for high selectivity. For reducing waveform direction of the input/output of the ceramic filters.
variation, it is recommended to input a buffer AMP
between ceramic filters.
0 1.2 0 1.2
1 1.0 1 1.0
Attenuation (dB)
Attenuation (dB)
2 0.8 2 0.8
3 0.6 3 0.6
4 0.4 4 0.4
5 0.2 5 0.2
6 0 6 0
7 7
10.5 10.6 10.7 10.8 10.9 10.5 10.6 10.7 10.8 10.9
Frequency (MHz) Frequency (MHz)
R2=560Ω R2=1kΩ
Group Delay Time (μsec.)
0 1.2 0 1.2
1 1.0 1 1.0
Attenuation (dB)
Attenuation (dB)
2 0.8 2 0.8
3 0.6 3 0.6
4 0.4 4 0.4
5 0.2 5 0.2
6 0 6 0
7 7
10.5 10.6 10.7 10.8 10.9 10.5 10.6 10.7 10.8 10.9
Frequency (MHz) Frequency (MHz)
0 1.2 0 1.2
1 1.0 1 1.0
Attenuation (dB)
Attenuation (dB)
2 0.8 2 0.8
3 0.6 3 0.6
4 0.4 4 0.4
5 0.2 5 0.2
6 0 6 0
7 7
10.5 10.6 10.7 10.8 10.9 10.5 10.6 10.7 10.8 10.9
Frequency (MHz) Frequency (MHz)
C=56pF C=82pF
Group Delay Time (μsec.)
0 1.2 0 1.2
1 1.0 1 1.0
Attenuation (dB)
Attenuation (dB)
2 0.8 2 0.8
3 0.6 3 0.6
4 0.4 4 0.4
5 0.2 5 0.2
6 0 6 0
7 7
10.5 10.6 10.7 10.8 10.9 10.5 10.6 10.7 10.8 10.9
Frequency (MHz) Frequency (MHz)
30
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Features 8.5±0.2
0.5±0.1
3.8±0.2
2.5±0.2 2.5±0.2
25 min. 15 min.
SFSKA5M50CF00-R3 5.500 fn±60 min. 600 max. 6.0 max. 600
[within 0 to fn] [within fn to 7.0MHz]
25 min. 15 min.
SFSKA6M00CF00-R3 6.000 fn±60 min. 600 max. 6.0 max. 470
[within 0 to fn] [within fn to 7.5MHz]
25 min. 15 min.
SFSKA6M50CF00-R3 6.500 fn±60 min. 600 max. 6.0 max. 470
[within 0 to fn] [within fn to 8.5MHz]
Area of Insertion Loss: at minimum loss point
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
9
Rg
4.8
RF
E1 E2 Voltmeter
R2 C2
S.S.G.
(1) : Input
(in mm) R1+Rg=R2=1000Ω ±5%, Rg=50Ω
(2) : Ground
C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter)
(3) : Output
E1:S.S.G. Output voltage
31
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
SFSKA5M50CF00-R3 SFSKA6M00CF00-R3
R1 R1
Rg Rg
RF RF
E1 E2 Voltmeter E1 E2 Voltmeter
R2 C2 R2 C2
S.S.G. S.S.G.
SFSKA6M50CF00-R3
R1
Rg
RF
E1 E2 Voltmeter
R2 C2
S.S.G.
(1) : Input
R1+Rg=R2=470Ω ±5%, Rg=50Ω
(2) : Ground
C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter)
(3) : Output
E1: S.S.G. Output voltage
c Frequency Characteristics
SFSKA4M50CF00-R3 SFSKA5M50CF00-R3
9
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 4.5 4.7 4.9 5.1 5.3 5.5 5.7 5.9 6.1 6.3 6.5
SFSKA6M00CF00-R3 SFSKA6M50CF00-R3
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
5.0 5.2 5.4 5.6 5.8 6.0 6.2 6.4 6.6 6.8 7.0 5.5 5.7 5.9 6.1 6.3 6.5 6.7 6.9 7.1 7.3 7.5
Frequency (MHz) Frequency (MHz)
32
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
0.0 2.0 4.0 6.0 8.0 10.0 0 2.0 4.0 6.0 8.0 10.0
Frequency (MHz) Frequency (MHz)
SFSKA6M00CF00-R3 SFSKA6M50CF00-R3
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
0 2.0 4.0 6.0 8.0 10.0 0 2.0 4.0 6.0 8.0 10.0
Frequency (MHz) Frequency (MHz)
33
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
3.8±0.1
∗
(3.5)
for IR headphone applications.
Center frequencies of 2.3, 2.8, 3.2, 3.8, 4.3, 4.8, 5.2, (2)
(3)
(4.93)
5.7MHz are available.
1.35±0.15
Realized small, thin and lightweight package,
Terminal Connection
compared with conventional LC filters. (0.1) 1.5±0.1 (2.0) 4-0.35 (1) : Input
(2) : Output
It helps to compose multi-channel circuit on one PCB. (3) (2)
(3) : Ground
(4) : Terminal for external
4-0.35
No frequency adjustment is required on PCB and it
0.25±0.1
contributes to the reduction of production cost. (4) (1) Tolerance unless otherwise
specified : ±0.1mm
( ) : Reference
(in mm)
c Features
1. SMD package in plastic emboss tape, available
for automatic placing.
2. They are slim, at only 1.5mm max. thickness,
and have a small mounting area (5.2x3.8mm) enabling
flexible PCB design.
3. Available for lead (Pb) free reflow soldering process.
4. Operating temperature range: 0 to +70°C
Storage temperature range: -55 to +85°C
5. No frequency adjustment is required in production
process.
6. Small, thin and lightweight package compared with
conventional LC filters
c Applications
1. IR headphone
2. Set Top Box for satellite broadcasting
25 min. 25 min.
SFSKB2M80GF00-R1 2.800 fn±75 min. 650 max. 6.0 max. 1000
[within 1.8 to 2.3MHz] [within 3.3 to 3.8MHz]
30 min. 30 min.
SFSKB3M20FF00-R1 3.200 fn±75 min. 650 max. 6.0 max. 1000
[within 2.2 to 2.8MHz] [within 3.8 to 4.2MHz]
30 min. 30 min.
SFSKB3M80GF00-R1 3.800 fn±75 min. 650 max. 6.0 max. 1000
[within 2.8 to 3.2MHz] [within 4.3 to 4.8MHz]
30 min. 30 min.
SFSKB4M30GF00-R1 4.300 fn±75 min. 650 max. 6.0 max. 1000
[within 3.3 to 3.8MHz] [within 4.8 to 5.3MHz]
30 min. 30 min.
SFSKB4M80GF00-R1 4.800 fn±75 min. 650 max. 6.0 max. 1000
[within 3.8 to 4.3MHz] [within 5.2 to 5.8MHz]
30 min. 30 min.
SFSKB5M20GF00-R1 5.200 fn±75 min. 650 max. 6.0 max. 1000
[within 4.2 to 4.8MHz] [within 5.7 to 6.2MHz]
30 min. 30 min.
SFSKB5M70GF00-R1 5.700 fn±75 min. 650 max. 6.0 max. 1000
[within 4.7 to 5.2MHz] [within 6.2 to 6.7MHz]
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
34
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1.3
1.6
1.3
(in mm)
c Test Circuit
SFSKB2M30GF00-R1/SFSKB3MZ0GF00-R1 SFSKB2M80GF00-R1/SFSKB3M20FF00-R1
Rg
(2) (3) (2) (3)
RF RF
C2
C2
R2
R2
Cc
E2
Cc
E2
E1
E1
Voltmeter Voltmeter
S.S.G. S.S.G.
R1+Rg=R2=1.0kΩ R1+Rg=R2=1.0kΩ
Cc=22pF±5% (1) : Input Cc=39pF±5% (1) : Input
C2=10pF (Including stray capacitance and (2) : Output C2=10pF (Including stray capacitance and (2) : Output
Input capacitance of RF Voltmeter) (3) : Ground Input capacitance of RF Voltmeter) (3) : Ground
E1 : S.S.G. Output Voltage (4) : Terminal for external capacitor E1 : S.S.G. Output Voltage (4) : Terminal for external capacitor
SFSKB4M30GF00-R1/SFSKB5M70GF00-R1 SFSKB4M80GF00-R1
Rg
C2
R2
R2
Cc
E2
Cc
E2
E1
E1
Voltmeter Voltmeter
S.S.G. S.S.G.
10
R1+Rg=R2=1.0kΩ R1+Rg=R2=1.0kΩ
Cc=33pF±5% (1) : Input Cc=15pF±5% (1) : Input
C2=10pF (Including stray capacitance and (2) : Output C2=10pF (Including stray capacitance and (2) : Output
Input capacitance of RF Voltmeter) (3) : Ground Input capacitance of RF Voltmeter) (3) : Ground
E1 : S.S.G. Output Voltage (4) : Terminal for external capacitor E1 : S.S.G. Output Voltage (4) : Terminal for external capacitor
SFSKB5M20GF00-R1
R1 (1) (4)
Rg
(2) (3)
RF
C2
R2
Cc
E2
E1
Voltmeter
S.S.G.
R1+Rg=R2=1.0kΩ
Cc=27pF±5% (1) : Input
C2=10pF (Including stray capacitance and (2) : Output
Input capacitance of RF Voltmeter) (3) : Ground
E1 : S.S.G. Output Voltage (4) : Terminal for external capacitor
35
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Frequency Characteristics
SFSKB2M30GF00-R1 SFSKB2M80GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
1.300 1.800 2.300 2.800 3.300 1.800 2.300 2.800 3.300 3.800
Frequency (MHz) Frequency (MHz)
SFSKB3M20FF00-R1 SFSKB3M80GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
2.200 2.700 3.200 3.700 4.200 2.800 3.300 3.800 4.300 4.800
Frequency (MHz) Frequency (MHz)
SFSKB4M30GF00-R1 SFSKB4M80GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
10 40 40
50 50
60 60
70 70
3.300 3.800 4.300 4.800 5.300 3.800 4.300 4.800 5.300 5.800
Frequency (MHz) Frequency (MHz)
SFSKB5M20GF00-R1 SFSKB5M70GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
4.200 4.700 5.200 5.700 6.200 4.700 5.200 5.700 6.200 6.700
Frequency (MHz) Frequency (MHz)
36
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
0.300 1.300 2.300 3.300 4.300 0.800 1.800 2.800 3.800 4.800
Frequency (MHz) Frequency (MHz)
SFSKB3M20FF00-R1 SFSKB3M80GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
1.200 2.200 3.200 4.200 5.200 1.800 2.800 3.800 4.800 5.800
Frequency (MHz) Frequency (MHz)
SFSKB4M30GF00-R1 SFSKB4M80GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
10
50 50
60 60
70 70
2.300 3.300 4.300 5.300 6.300 2.800 3.800 4.800 5.800 6.800
Frequency (MHz) Frequency (MHz)
SFSKB5M20GF00-R1 SFSKB5M70GF00-R1
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
3.200 4.200 5.200 6.200 7.200 3.700 4.700 5.700 6.700 7.700
Frequency (MHz) Frequency (MHz)
37
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
8.4 max.
7.5±0.3
MARKING
recommendable intermediate filters, having such
EIAJ
distinctive features as high selectivity, high CODE
5.0 max.
Additionally, its easy matching with IC helps create an
easy circuit design.
1.5±0.3 2.0±0.3
2.0±0.3 1.5±0.3 1.6±0.3
c Features Connection
(1): Input
(1) (2) (3)
1. The filters are mountable by automatic placers (2): Ground
(3): Output
and can be reflow soldered and withstand (in mm)
washing.
2. The filters are wide bandwidth and high
selectivity, so they are suitable for car radio
and multi-band radio.
S(3) (4)S
1.6
(2)
(1) (6) 60T 125T 28T
7.45
11 (Bottom view)
1.55
No load Qu 40
c Test Circuit
R1
(1) (3)
(2)
RF Voltmeter
Rg
E1 R2 E2
S.S.G.
0dBm
(1): Input
Rg+R1=R2=Input/Output Impedance (2): Ground
E1: S.S.G. Output Voltage (3): Output
38
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Frequency Characteristics
SFPKA450KH1A-R1 SFPKA450KG1A-R1
0 400 0 400
10 360 10 360
20 320 20 320
30 280 30 280
40 240 40 240
Attenuation (dB)
Attenuation (dB)
G.D.T. (μsec.)
G.D.T. (μsec.)
50 200 50 200
60 160 60 160
70 120 70 120
80 80 80 80
90 40 90 40
100 0 100 0
425 450 475 425 450 475
Frequency (kHz) Frequency (kHz)
11
39
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±0.3
MARKING
7.3±0.3
0.3±0.1
stability, high attenuation, and adjustment-free
0.8±0.1
operation. Additionally, its easy matching with IC
3.0±0.3
1.5 max.
helps create an easy circuit design. 0.15±0.05
This is the most suitable for car stereo and 2.7±0.3 1.2±0.5 0.6±0.1
4.2±0.3
(1) : Input
SFPLA Series (2) : Ground
(3)
(3) : Output
(in mm)
3.3±0.5
11.0±0.5
MARKING
7.0±0.5
EIAJ
CODE
7.5±0.5
1.5 max.
0.8±0.1
3.5±0.5
0.15
2.9±0.3 2.6±0.3 0.6±0.1
2.9±0.3
2.9—0.3
1.2±0.5 Connection
4.3±0.3
(1): Input
1.35±0.5
CFWLA Series (4) (3) (2) (1) (2)(3)(4): Ground
(5) (5): Output
12
c Recommended IFT c Test Circuit
Type SFPLA/CFWLA
Item 7x7mm IFT
S(3) (4)S Rg
(2)
(1) (6) 60T 125T 28T RF
R2
SSG
(Bottom view) Voltmeter
No load Qu 40 Ground
40
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Frequency Characteristics
IFT+SFPLA450KH1A-B0 IFT+CFWLA450KHFA-B0
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30
30
40
40
50
50
60
60
70
430 440 450 460 470 70
430 440 450 460 470
Frequency (kHz) Frequency (kHz)
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40 40
50 50
60 60
70 70
80 80
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
Frequency (MHz) Frequency (MHz)
12
41
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7.0±0.3
MARKING
7.3±0.3
0.3±0.1
high attenuation, and adjustment-free operation.
0.8±0.1
Additionally, its easy matching with IC helps create
3.0±0.3
1.5 max.
an easy circuit design. 0.15±0.05
Especially, CFULA/CFWLA_Y series improves the 2.7±0.3 1.2±0.5 0.6±0.1
4.2±0.3
(1) : Input
stereo with its wide band and flat characteristics of SFPLA Series (2) : Ground
(3)
(3) : Output
group delay time. (in mm)
3.3±0.5
11.0±0.5 8.0±0.3
MARKING MARKING
7.0±0.5
7.0±0.3
EIAJ EIAJ
CODE CODE
7.3±0.3
7.5±0.5
1.5 max.
0.3±0.1
0.8±0.1 0.8±0.1
3.0±0.3
3.5±0.5
1.5 max.
0.15 0.15±0.05
2.9±0.3 2.6±0.3 0.6±0.1 2.7±0.3 0.6±0.1
2.9±0.3
2.9—0.3 1.2±0.5
1.2±0.5 Connection
(2) (1)
4.2±0.3
Connection
4.3±0.3
(1): Input
1.35±0.5
CFWLA Series (4) (3) (2) (1) (2)(3)(4): Ground CFULA Series (1): Input
(5) (5): Output (3) (2): Ground
(3): Output
2.3±0.5 2.0±0.3 (in mm) 3.3±0.5 (in mm)
Center 6dB Selectivity (-) Selectivity (+) Insertion GDT 20µsec. Input/Output
Part Number Frequency (fo) Bandwidth Loss Bandwidth Impedance Element
(kHz) (kHz) (dB) (dB) (dB) (kHz) (ohm)
SFPLA450KG1A-B0 450.0 ±1.0kHz fn±4.5 min. 30 min.[fn-9kHz] 30 min.[fn+9kHz] 6.0 max. - 2000 4
SFPLA450KF1A-B0 450.0 ±1.0kHz fn±6.0 min. 40 min.[fn-12.5kHz] 40 min.[fn+12.5kHz] 6.0 max. - 2000 4
SFPLA450KE1A-B0 450.0 ±1.0kHz fn±7.5 min. 40 min.[fn-15kHz] 40 min.[fn+15kHz] 6.0 max. - 1500 4
SFPLA450KD1A-B0 450.0 ±1.0kHz fn±10.0 min. 40 min.[fn-20kHz] 40 min.[fn+20kHz] 4.0 max. - 1500 4
CFULA450KG1Y-B0 450.0 ±1.0kHz fn±4.5 min. 40 min.[fn-15kHz] 40 min.[fn+15kHz] 10.0 max. fn±3 2000 4
CFULA450KF1Y-B0 450.0 ±1.0kHz fn±6.0 min. 40 min.[fn-17.5kHz] 40 min.[fn+17.5kHz] 9.0 max. fn±4 2000 4
CFULA450KD1Y-B0 450.0 ±1.0kHz fn±10.0 min. 40 min.[fn-25kHz] 40 min.[fn+25kHz] 7.0 max. fn±7 1500 4
CFWLA450KG1Y-B0 450.0 ±1.0kHz fn±4.5 min. 50 min.[fn-15kHz] 50 min.[fn+15kHz] 11.0 max. fn±4 2000 6
CFWLA450KF1Y-B0 450.0 ±1.0kHz fn±6.0 min. 50 min.[fn-17.5kHz] 50 min.[fn+17.5kHz] 10.0 max. fn±5 2000 6
CFWLA450KD1Y-B0 450.0 ±1.0kHz fn±10.0 min. 50 min.[fn-25kHz] 50 min.[fn+25kHz] 8.0 max. fn±8 1500 6
CFWLA450KGFA-B0 450.0 (fn) fn±4.5 min. 50 min.[fn-10kHz] 50 min.[fn+10kHz] 6.0 max. - 2000 6
CFWLA450KFFA-B0 450.0 (fn) fn±6.0 min. 50 min.[fn-12.5kHz] 50 min.[fn+12.5kHz] 6.0 max. - 2000 6
13 CFWLA450KEFA-B0 450.0 (fn) fn±7.5 min. 50 min.[fn-15kHz] 50 min.[fn+15kHz] 6.0 max. - 1500 6
CFWLA450KDFA-B0 450.0 (fn) fn±10.0 min. 50 min.[fn-20kHz] 50 min.[fn+20kHz] 4.0 max. - 1500 6
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 6dB bandwidth.
(fn) means nominal center frequency (450kHz).
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
42
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
S(3) (4)S Rg
(2)
(1) (6) 60T 125T 28T RF
R2
SSG
(Bottom view) Voltmeter
No load Qu 40 Ground
c Frequency Characteristics
IFT+SFPLA450KF1A-B0 IFT+CFWLA450KFFA-B0
0 0
10 10
20 20
Attenuation (dB)
Attenuation (dB)
30 30
40
40
50
50
60
60
70
430 440 450 460 470 70
430 440 450 460 470
Frequency (kHz) Frequency (kHz)
IFT+CFULA450KF1Y-B0 IFT+CFWLA450KF1Y-B0
0 0
10 10
20 200 20 200
Attenuation (dB)
Attenuation (dB)
30 100 30 100
40 0 40 0
50 50
60 60
70 70
430 440 450 460 470 430 440 450 460 470
Frequency (kHz) Frequency (kHz)
13
43
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c SFPLA450KH1A-B0
+1
Center Frequency
Temperature (°C)
-20 0 20 40 60 80
(kHz)
-1
+1
Insertion Loss
0 20 40
(dB)
0
-20 60 80
Temperature (°C)
-1
+1 Temperature (°C)
3dB Bandwidth
20 40 60 80
(kHz)
0
-20 0
-1
44
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Features 8.5±0.2
0.5±0.1
3.8±0.2
delay time
1.3±0.2
2. Small and thin package 0.3±0.1
(1) : Input
3. Reflow-solderable 1.3±0.2
(2) : Ground
(1) (2) (3) (3) : Output
(in mm)
2.5±0.2 2.5±0.2
Nominal Center Frequency (fn1) Attenuation (at fn1) 30dB Attenuation BW (fn1)
Part Number
(MHz) (dB) (kHz)
TPSKA4M50B00-R3 4.500 35 min. 50 min.
TPSKA5M50B00-R3 5.500 35 min. 70 min.
TPSKA6M00B00-R3 6.000 35 min. 70 min.
TPSKA6M50B00-R3 6.500 35 min. 70 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
L
1.0 1.0 1.0
R1
1.5 1.5
Rg
50Ω R2
RF
4.8
S.S.G. Voltmeter
Rg=50Ω L=15μH
R1=330Ω
R2=1.0kΩ
(in mm)
c Frequency Characteristics
TPSKA4M50B00-R3 TPSKA5M50B00-R3
0 0
10 10
Attenuation (dB)
Attenuation (dB)
20 20
30 30
14
40 40
50 50
60 60
70 70
4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0
Frequency (MHz) Frequency (MHz)
45
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Frequency Characteristics
TPSKA6M00B00-R3 TPSKA6M50B00-R3
0 0
10 10
Attenuation (dB)
Attenuation (dB)
20 20
30 30
40 40
50 50
60 60
70 70
5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0
Frequency (MHz) Frequency (MHz)
0 700 0 1000
10 600 10 800
20 500 20 600
Attenuation (dB)
Attenuation (dB)
G.D.T. (nsec.)
G.D.T. (nsec)
30 400 30 400
40 300 40 200
50 200 50 0
60 100 60
70 0 70
80 80
0 1.0 2.0 3.0 4.0 5.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
Frequency (MHz) Frequency (MHz)
TPSKA6M00B00-R3 TPSKA6M50B00-R3
0 1000 0 1000
10 800 10 800
20 600 20 600
Attenuation (dB)
Attenuation (dB)
G.D.T. (nsec.)
G.D.T. (nsec.)
30 400 30 400
40 200 40 200
50 0 50 0
60 60
70 70
80 80
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
Frequency (MHz) Frequency (MHz)
14
46
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
0.3±0.2
4.5±0.1
CDSCB10M7 series forms a resonator on a piezoelectric
1.4 max.
2.0±0.1
ceramic substrate. In combination with ICs, this type
obtains stable demodulation characteristics in a wide
0.2±0.2 0.4±0.05
bandwidth. 4.1 max.
1.0 max.
They have 1.0mm max. thickness and small mounting area
(4.5x2.0mm). 0.4(ref.) 0.4(ref.)
0.8±0.1 0.8±0.1
c Features
1. Compact and high reliability and recommended for
automotive applications.
1.5±0.1 1.5±0.1 (in mm)
2. Can be combined with various ICs. The IC is
determined by the last number in the part number.
3. Stable demodulation characteristics can be
obtained without adjustment.
4. Stable temperature characteristics.
5. Available lead (Pb) free solder reflow.
15
47
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
3.0
2.6
1.0 2.0 1.0
(in mm)
c Test Circuit
CDSCB10M7GA105A-R0 CDSCB10M7GA113-R0
Vcc (1.2V)
Vcc (3.0V)
0.1μ
10μ
0.01μ
0.01μ
+
0.01μ
48 47 46 45 44 43 42 41 40 39 38 37 0.1μ
+ 1 36
100μ 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
2 35 S.S.G.
3 34 TA2154FN (TOSHIBA)
4 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
+
5 32
X 2.2μ
680p
6 31
TEA5757HL
7 (PHILIPS) 30
0.01μ
0.01μ
8 29 D.C. OUT AF OUT
9 28
100k X: CDSCB10M7GA113-R0
10 27 S.S.G.
Unit C: F
11 26 R: Ω
10
DC OUT 12 25
13 14 15 16 17 18 19 20 21 22 23 24
+
0.1μ
0.1μ
330p 4.7μ
0.47μ
X
0.22μ
AFC (n)
AFC (p)
150 X: CDSCB10M7GA105A-R0
Unit C: F
AF OUT R: Ω
CDSCB10M7GA119-R0 CDSCB10M7GA121-R0
Vcc (3.0V)
AF Output 0.01μ D.C. Output Vcc (3.2V)
IF Input AF Output
68p
220k 0.01μ
0.01μ 0.015μ
15p
10p
10p
22μ+
120p 82p
10 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
4.7μ
LV23100V (SANYO)
0.01μ 48 47 46 45 44 43 42 41 40 39 38 37 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
0.01μ 1 36 X 10k
2 35
+
1μ
3 34 10μ 0.047μ
4 33 1000p +
0.047μ
5 32
47p
X
6 TRF6901 31 +
7 (TEXAS INSTRUMENTS) 30
8 29 0.01μ 0.47μ
9 28
10k
100p 10 27
11 26
12 25
13 14 15 16 17 18 19 20 21 22 23 24
3.3k
0.1μ +
0.01μ 0.22μ 1μ
+
0.047μ
0.47μ
100μ
75
S.G. +
100p
100p 10k
10k
18 17 16 15 14 13 12 11 10
18 17 16 15 14 13 12 11 10
PIC16F84 (Control IC)
PIC16F84 1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
X: CDSCB10M7GA119-R0 1k
1k
10k Unit C : F
+ R: Ω 2.2μ + 10k
0.1μ Unit C: F
2.2μ 0.1μ X: CDSCB10M7GA121-R0
L: H R: Ω
15
48
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
c Test Circuit
CDSCB10M7GA135-R0 CDSCB10M7GA136-R0
Vcc (5.0V) Vcc (5.0V)
AF-OUT FKS-OUT 330p
0.1μ 0.1μ
24 23 22 21 20 19 18 17
25 16
26 15
330k 28
TH7122 13 330p
[Internal AFC Enabled]
220k 29 12
(MELEXIS)
30 11
0.01μ 31 10
24 23 22 21 20 19 18 17
32 9
0.01μ
25 16
1 2 3 4 5 6 7 8
12p C.D. FKS-OUT
26 15 0.01μ 0.1μ
0.01μ 330p
27 14 AF-OUT
1000p
28 TH71101, TH71102, 13 330p 100k
TH71111 or TH71112 0.033μ
29 (MELEXIS) 12
0.01μ 1000p S.G.
30 11 C.D. 3.3k
330p 0.01μ
31 10 330p
0.01μ
32 9
100k 100p
1 2 3 4 5 6 7 8
18 17 16 15 14 13 12 11 10
CDSCB10M7GF072-R0 CDSCB10M7GF109-R0
Vcc (3V)
0.01μ
Vcc (3V)
1.2μ
4.7μ
R
X
AF OUT 0.01μ R X 0.01μ
D.C. OUT AF OUT
10p
1000p 0.01μ
16 15 14 13 12 11 10 9 12k 8p
51k
0.01μ
TA31161 (TOSHIBA)
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
0.01μ
0.01μ X: CDSCB10M7GF072-R0
+ R: 820
TK14588V (TOKO)
33μ 0.01μ Unit C: F 1 2 3 4 5 6 7 8
R: Ω
0.01μ
0.01μ
0.01μ
IF IN L: H
51
+
0.01μ
4.7μ
S.S.G.
X: CDSCB10M7GF109-R0
R: 820
Unit C: F
R: Ω
L: H
CDSCB10M7GF123-R0 CDSCB10M7GF126-R0
Vcc (5.0V) Vcc (5.0V)
AF OUT
10μ
0.01μ
DC-OUT
+
0.01μ
DC-OUT
3300p
0.01μ
100p
1000p
0.01μ
0.01μ
20 19 18 17 16 15 14 13 12 11
24 23 22 21 20 19 18 17 16 15 14 13
NJM2295AV (JRC)
TA31275FN (TOSHIBA)
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10 11 12
0.01μ
+ 8p
10μ
0.01μ
1.8k
0.1μ
C.D. 180
0.01μ
0.1μ
0.1μ
0.1μ
0.01μ
10μ+
10μ+
X: CDSCB10M7GF123-R0 X: CDSCB10M7GF126-R0
S.S.G. S.G.
Unit C: F Unit C: F
R: Ω R: Ω
15
49
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
AF Output AF Output
100 10 100 10
AF Output Voltage (mV)
T.H.D. (%)
Distortion
Distortion
10 1 10 1
1 0.1 1 0.1
CDSCB10M7GA119-R0 CDSCB10M7GA121-R0
1000 100 1000 100
AF Output AF Output
100 10 100 10
AF Output Voltage (mV)
T.H.D. (%)
Distortion Distortion
10 1 10 1
1 0.1 1 0.1
CDSCB10M7GA135-R0 CDSCB10M7GA136-R0
1000 1000
100 100
AF Output Voltage (mV)
10 10
1 1
50
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
100 10 100 10
T.H.D. (%)
T.H.D. (%)
10 1 10 1
1 0.1 1 0.1
c S Curve
CDSCB10M7GF123-R0 CDSCB10M7GF126-R0
2.5 4.0
2.0
3.0
1.5
Volt (V)
Volt (V)
1.0
2.0
0.5
0.0 1.0
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz) Frequency (MHz)
15
51
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
ex. : CDSCB10M7GA105A-R0
Suffix Number
IC Manufacturer IC Part Number Suffix Number IC Manufacturer IC Part Number Suffix Number
ATMEL U4313B 081 TOSHIBA TA2003 031
U4490B 034V TA2007 033
INFINEON TDA1576T 051 TA2008A / AN 045
TDA6160X 038 TA2022 050
Panasonic AN7004 011 TA2057 057
AN7232 053 TA2099N 082
Freescale MC13156 049 TA2104AFN 080
MC13158 073 TA2104F 080A
Renesas μPC1391M 056 TA2111N / F / FN 077
NXP NE604 020 TA2132 092
SA605 042 TA2132BP 092D
SA626 047 TA2142FN 102
SA636DK 096 TA2149AN 100A
SA639 085 TA2149N 100
TDA1596T 120 TA2154FN 113
TEA5710 040 TA2159F 116
TEA5757HL 105A TA31161 072
TEA5762 / 5757 061 TA31275FN 123
UAA3220TS 098 TA7303P 008
ROHM BA1448 060 TA7640AP 006
BA4230AF 005 TA8122AN / AF 016
BA4234L 004 TA8132AN / AF 018
SAMSUNG S1A0903 118A TB2132FN 128
SANYO LA1225M 108A
LA1814M 115
LA1823 101
LA1827M 083
LA1831 043
LA1832 / M 046
LA1833 086
LA1835 / M 048
LA1838 / M 079
LA7770 023
LV23000M 114
LV23100V 121
SONY CX1691M 078
CX-20029 001
CXA1111 093
CXA1238 027
CXA1238N 027N
CX1343M 032
CXA1376AM 054
CXA1538M / N / S 069
CXA1611 075
CX3067M 076
T. I. TRF6901 119
TOKO TK14570L 122
TK14583V 112
TK14588V 109
52
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
230
Heating
Pre-heating (230°C)
(150-180°C)
100
Gradual
Cooling
(4) Other
(a) The component may be damaged if excess
[Component Direction]
mechanical stress is applied to it mounted on the
Place the
printed circuit board. component
(b) Design layout of components on the PC board to lateral to the
direction in
minimize the stress imposed on the warp or flexure of which stress
the board. acts.
(c) After installing components, if solder is excessively [Component Layout Close to Board]
applied to the circuit board, mechanical stress will
Perforation
cause destruction resistance characteristics to B Susceptibility to
stress is in the order
degrade. To prevent this, be extremely careful in
C
of : A>C>B
determining shape and dimension before designing A Slit
Notice
Continued from the preceding page.
2. Wash
Do not clean or wash the component as it is not
hermetically sealed.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Accurate test circuit values are required to measure 3. For safety purposes, connect the output of filters to the IF
electrical characteristics. Miscorrelation may be caused if amplifier through a D.C. blocking capacitor. Avoid
there is any deviation, especially stray capacitance, from applying a direct current to the output of ceramic filters.
the test circuit in the specification.
2. The components, packed in a moisture proof bag (dry
pack), are sensitive to moisture. The following treatment
is required before applying reflow soldering, to avoid
reliability degradation caused by thermal stress. When
unpacked, store the component in an atmosphere of
reflow 30°C and below 60%R.H., and solder within 1
week.
54
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
230
Heating
Pre-heating (230°C)
(150-180°C)
100
Gradual
Cooling
(4) Other
(a) The component may be damaged if excess
[Component Direction]
mechanical stress is applied to it mounted on the
Put the
printed circuit board. component
(b) Design layout of components on the PC board to lateral to the
direction in
minimize the stress imposed on the warp or flexure of which stress
the board. acts.
(c) After installing components, if solder is excessively [Component Layout Close to Board]
applied to the circuit board, mechanical stress will
Perforation
cause destruction resistance characteristics to B Susceptibility to
stress is in the order
degrade. To prevent this, be extremely careful in
C
of : A>C>B
determining shape and dimension before designing A Slit
55
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Continued from the preceding page.
2. Wash
Do not clean or wash the component as it is not
hermetically sealed.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Accurate test circuit values are required to measure
electrical characteristics.
Miscorrelation may be caused if there is any deviation,
especially stray capacitance, from the test circuit in the
specification.
2. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
56
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Do not use this product with bend. The component may 5. In case of overcoating the component, conditions such as
be damaged if excess mechanical stress is applied to it material of resin, cure temperature, and so on should be
mounted on the printed circuit board. evaluated well.
2. Do not apply any type of reflow soldering on the 6. Accurate test circuit values are required to measure
component. electrical characteristics. It may be a cause of
3. Do not clean or wash the component as it is not miscorrelation if there is any deviation, especially stray
hermetically sealed. capacitance, from the test circuit in the specification.
4. Do not use strong acidity flux, more than 0.2wt% chlorine 7. For safety purposes, avoid applying a direct current
content, in flow soldering. between the terminals.
57
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
230
Heating
Pre-heating (230°C)
(150-180°C)
100
Gradual
Cooling
(4) Other
(a) The component may be damaged if excess
[Component Direction]
mechanical stress is applied to it mounted on the
printed circuit board. Put the
component
(b) Design layout of components on the PC board to lateral to the
minimize the stress imposed on the warp or flexure of direction in
which stress
the board. acts.
(c) After installing chips, if solder is excessively applied to [Component Layout Close to Board]
the circuit board, mechanical stress will cause
destruction resistance characteristics to degrade. To Susceptibility to
Perforation B
stress is in the order
prevent this, be extremely careful in determining
of : A>C>B
shape and dimension before designing the circuit C
A Slit
board diagram.
(d) When the positioning claws and pick-up nozzle are
worn, the load is applied to the components while
positioning is concentrated to one positioning
accuracy, etc. Careful checking and maintenance are
necessary to prevent unexpected trouble.
(e) When correcting chips with a soldering iron, the tip of
the soldering iron should not directly touch the chip
component.
2. Wash
Do not clean or wash the component as it is not
hermetically sealed.
Continued on the following page.
58
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Continued from the preceding page.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Accurate test circuit values are required to measure
electrical characteristics.
Miscorrelation may be caused if there is any deviation,
especially stray capacitance, from the test circuit in the
specification.
2. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
59
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
200
Heating
Pre-heating (200°C)
(150-170°C)
100
Gradual
Cooling
(4) Other
(a) The component may be damaged if excess
[Component Direction]
mechanical stress is applied to it mounted on the
Put the
printed circuit board. component
(b) Design layout of components on the PC board to laterally to the
direction in
minimize the stress imposed on the warp or flexure of which stress
the board. acts.
(c) After installing components, if solder is excessively
[Component Layout Close to Board]
applied to the circuit board, mechanical stress will
cause destruction resistance characteristics to
Susceptibility to
degrade. To prevent this, be extremely careful in Perforation B
stress is in the order
determining shape and dimension before designing of : A>C>B
C
the circuit board diagram. A Slit
60
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Continued from the preceding page.
2. Wash
Do not clean or wash the component as it is not
hermetically sealed.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Accurate test circuit values are required to measure
electrical characteristics.
Miscorrelation may be caused if there is any deviation,
especially stray capacitance, from the test circuit in the
specification.
2. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
61
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
230
Heating
(230°C)
Pre-heating
100
(150-180°C) Gradual
Cooling
(3) Other
Do not use strong acidity flux, more than 0.2wt% chlorine
content, in reflow soldering.
2. Wash
(1) Cleaning Solvent
CFC alternatives (HCFC Series), Isopropyl Alcohol (IPA),
7ATER $EMINERALIZED 7ATER #LEANING 7ATER 3OLUTION
(Cleanthrough-750H, Pine Alpha 100S), Silicon
4ECHNOCARE &27
(3) Notice
s 7HEN COMPONENTS ARE IMMERSED IN SOLVENT BE SURE TO
maintain the temperature of components below the
temperature of solvent.
s 0LEASE DO NOT USE ULTRASONIC CLEANING
s 4OTAL WASHING TIME SHOULD BE MINUTES MAXIMUM
s 0LEASE ENSURE THE COMPONENT IS THOROUGHLY EVALUATED IN
your application circuit.
s 0LEASE DO NOT USE CHLORINE PETROLEUM OR ALKALI CLEANING
solvent.
s )F YOU PLAN TO USE ANY OTHER TYPES OF SOLVENTS PLEASE
consult with Murata or a Murata representative prior to
using.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
Continued on the following page.
62
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Continued from the preceding page.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. If the component is cleaned, please confirm that the 3. For safety purposes, connect the output of filters to the IF
reliability has not been degraded. amplifier through a D.C. blocking capacitor. Avoid
2. The components, packed in a moisture-proof bag (dry applying a direct current to the output of ceramic filters.
pack), are sensitive to moisture. The following treatment
is required before applying reflow soldering, to avoid
package cracks or reliability degradation caused by
thermal stress. When unpacked, store the component in
an atmosphere of below 25°C and below 65%R.H., and
solder within 48 hours.
63
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Do not use this product with bend. The component may 5. Conformal coating of the component is not acceptable
be damaged if excessive mechanical stress is applied to due to non-sealed construction.
it mounted on the printed circuit board. 6. Accurate test circuit values are required to measure
2. All kinds of reflow soldering must not be applied on the electrical characteristics. Miscorrelation may be caused if
component. there is any deviation, especially stray capacitance, from
3. Do not clean or wash the component as it is not the test circuit in the specification.
hermetically sealed. 7. For safety purposes, connect the output of filters to the IF
4. Do not use strong acidity flux, more than 0.2wt% chlorine amplifier through a D.C. blocking capacitor. Avoid
content, in flow soldering. applying a direct current to the output of ceramic filters.
64
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
230
Heating
Pre-heating (230°C)
(150-180°C)
100
Gradual
Cooling
(4) Other
(a) The component may be damaged if excess
[Component Direction]
mechanical stress is applied to it mounted on the
printed circuit board. Put the
component
(b) Design layout of components on the PC board to lateral to the
minimize the stress imposed on the warp or flexure of direction in
which stress
the board. acts.
(c) After installing chips, if solder is excessively applied to [Component Layout Close to Board]
the circuit board, mechanical stress will cause
destruction resistance characteristics to degrade. To Susceptibility to
Perforation B
stress is in the order
prevent this, be extremely careful in determining
of : A>C>B
shape and dimension before designing the circuit C
A Slit
board diagram.
(d) When the positioning claws and pick-up nozzle are
worn, the load is applied to the components while
positioning is concentrated to one positioning
accuracy, etc. Careful checking and maintenance are
necessary to prevent unexpected trouble.
(e) When correcting chips with a soldering iron, the tip of
the soldering iron should not directly touch the chip
component.
2. Wash
Do not clean or wash the component as it is not
hermetically sealed.
Continued on the following page.
65
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Continued from the preceding page.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Accurate test circuit values are required to measure
electrical characteristics.
Miscorrelation may be caused if there is any deviation,
especially stray capacitance, from the test circuit in the
specification.
2. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
66
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Temperature (°C)
230
Heating
Pre-heating (230°C)
(150-180°C)
100
Gradual
Cooling
(4) Other
(a) The component may be damaged if excess
[Component Direction]
mechanical stress is applied to it mounted on the Place the
printed circuit board. component
laterally to the
(b) Design layout of components on the PC board to
direction in
minimize the stress imposed on the warp or flexure of which stress
the board. acts.
(c) After installing components, if solder is excessively [Component Layout Close to Board]
applied to the circuit board, mechanical stress will
Perforation B
cause destruction resistance characteristics to Susceptibility to
stress is in the order
degrade. To prevent this, be extremely careful in
A C of : A>C>B
determining shape and dimension before designing Slit
67
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice
Continued from the preceding page.
2. Wash
Do not clean or wash the component as it is not
hermetically sealed.
3. Coating
In case of overcoating the component, conditions such as
material of resin, cure temperature, and so on should be
evaluated well.
o Rating
The component may be damaged if excessive mechanical
stress is applied.
o Handling
1. Accurate test circuit values are required to measure
electrical characteristics. Miscorrelation may be caused if
there is any deviation, especially stray capacitance, from
the test circuit in the specification.
2. For safety purposes, avoid applying a direct current
between the terminals.
68
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Packaging
c Minimum Quantity
Taping
Ammo Pack Bulk Magazine Box
ø330mm ø180mm
CERAFILr<10.7MHz>
SFECF 2,000
SFECV/SFECK 2,000
SFELF 1,500 500
CERAFILr<2.3-6.5MHz>
SFSKA 3,000
SFSKB 3,000
CERAFILr<455kHz>
CFULA 200
CFWLA 1,000 50 150
SFPLA 1,000 50 200
Ceramic Traps<4.5-6.5MHz>
TPSKA 3,000
Ceramic Discriminators<10.7MHz>
CDSCB 2,000
240 to 280
ø13.0±0.5 400 to 560
5.5±0.05
12.0±0.2
-1.5
60 +1.0
180 +0
4.1±0.1
-0
2.0±0.5
4.1±0.1
4.0±0.1 +0.1
Peeling strength 3.35 -0.05
0.3±0.05
(0.05)
1.84±0.1
s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UP ( ): Reference
(in mm)
ø13.0±0.5 400-560
12.0±0.2
7.3±0.01
180 –1.5
+1.0
∗ ∗ ∗ ∗ ∗
+0
60 –0
∗∗ ∗∗ ∗∗ ∗∗ ∗∗
2.0±0.5
4.0±0.1 3.0±0.1
0.3±0.05
1.9±0.1
1.7 –0.05
+0.1
Chip filter
Peeling strength 0.1 to 0.7N +1.0
(3°) 13.0 –0
Cover film
10° max. 17.0±1.0
Packaging
Continued from the preceding page.
dh dh
P2 P
dS1
W2
H0
L1
W0
L2
W1
W
F 1 F1 D0
P1 F
P0 t
(in mm)
70
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Packaging
Continued from the preceding page.
1.75±0.1
+0.1
ø1.5 –0.0 2.0±0.1 4.0±0.1
Trailer Leader
160 to 190 Cover film
7.5±0.1
16.0±0.2
Empty Components Empty
9.0±0.1
240 to 280 min.
2.2±0.5 400 to 560
330±2
80±1
Peeling strength +0.1 4.3±0.1
0.3±0.05
2.3±0.1
+0.1
2.1–0.05
ø1.5 –0.0 8.0±0.1
(0.1 to 0.7N) Chip filter
Cover film 10° max. (3°)
ø13.0±0.2
17.5±0.5
User direction of feed 21.5±1.0
s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UPSIDE
(in mm)
4.0±0.1 +0.1
2.0±0.1 ø1.5 –0.0
Trailer Leader
160 to 190 Cover Film
5.5±0.1
12.0±0.2
Empty Components
5.6±0.1
∗ ∗ ∗ ∗ Empty
240 to 280
400 to 560
(ø330)
(ø80)
8.0±0.1
1.6±0.1
ø13.0±0.2 2.2±0.2
Cover Film
4.2±0.1
5SER DIRECTION OF FEED
13.5±1.0 Label
17.5±1.5
s 0ART .UMBER MARKED SIDE IS ALWAYS FACING UPSIDE
(in mm)
ø13.0±0.2
16.0±0.2
400 to 560
8.8±0.1
330±2
80±1
2.2±0.5
12.0±0.1
User direction of feed 5.3±0.1
(in mm)
71
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Packaging
Continued from the preceding page.
8.1±0.3 10±0.3
18.7±0.3
ends. Above should be the minimum packaging unit.
HP51M0003-02
2. Quality of Magazine
1.1 1.1
(1) Transparent so that input / output direction is visually (in mm)
Tolerance unless otherwise specified: ±0.2
recognizable.
(2) With an angle of 35° CERAFILr should slip down Material: Polycarbonate
Camber of Case: ±1mm max. against entire length (reference)
smoothly.
Twist of Case: ±0.5mm max. (reference)
(3) Antistatic finish
(4) Recycling
Note: Magazines should be sent back for recycling.
(Therefore, empty magazines should not be damaged.)
ANTISTATIC
2. Quality of Magazine
muRataHP51M0064
(1) Transparent so that input / output direction is visually
recognizable. 5.3±0.3
0.6
(2) With an angle of 35° CERAFILr should slip down (in mm)
Tolerance unless otherwise specified: ±0.2
smoothly.
(3) Antistatic finish Material: Polycarbonate
Camber of Case: ±1mm max. against entire length (reference)
(4) Recycling
Twist of Case: ±0.5mm max. (reference)
Note: Magazines should be sent back for recycling.
(Therefore, empty magazines should not be damaged.)
72
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Packaging
Continued from the preceding page.
1.75±0.1
+0.1
ø1.5 –0.0 2.0±0.1 4.0±0.1
Trailer Leader
160 to 190 Cover film
7.5±0.1
16.0±0.2
Empty Components Empty
9.0±0.1
240 to 280 min.
2.2±0.5 400 to 560
330±2
80±1
Peeling strength +0.1 4.3±0.1
0.3±0.05
2.3±0.1
+0.1
2.1–0.05
ø1.5 –0.0 8.0±0.1
(0.1 to 0.7N) Chip filter
Cover film 10° max. (3°)
ø13.0±0.2
17.5±0.5
User direction of feed 21.5±1.0
s 0ART NUMBER MARKED SIDE IS ALWAYS FACING UPSIDE
(in mm)
12.0±0.2
180 +0.1
-1.5
+0.1
60 -0
+0.1 2.0±0.5
4.0±0.1
0.3±0.05
1.1±0.1
MAX
ø1.5 -0
0EELING STRENGTH 2.2±0.1
0.1 to 0.7N Cover film (3°)
10° +1.0
13.0 -0
17.0±1.0
73
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
74
Global Locations
For details please visit www.murata.com
Note
1 Export Control 2 Please contact our sales representatives or 3 Product specifications in this catalog are as of July
product engineers before using the products in 2012. They are subject to change or our products
For customers outside Japan: this catalog for the applications listed below, in it may be discontinued without advance notice.
No Murata products should be used or which require especially high reliability for the Please check with our sales representatives
sold, through any channels, for use in the prevention of defects which might directly or product engineers before ordering. If there
design, development, production, utilization, damage a third party’s life, body or property, or are any questions, please contact our sales
maintenance or operation of, or otherwise when one of our products is intended for use representatives or product engineers.
contribution to (1) any weapons (Weapons of in applications other than those specified in
Mass Destruction [nuclear, chemical or biological this catalog. 4 Please read rating and CAUTION (for storage,
weapons or missiles] or conventional weapons) operating, rating, soldering, mounting and
1 Aircraft equipment handling) in this catalog to prevent smoking
or (2) goods or systems specially designed or
intended for military end-use or utilization by and/or burning, etc.
2 Aerospace equipment
military end-users.
3 Undersea equipment 5 This catalog has only typical specifications.
For customers in Japan: Therefore, please approve our product
4 Power plant equipment specifications or transact the approval sheet
For products which are controlled items subject for product specifications before ordering.
to the “Foreign Exchange and Foreign Trade Law” 5 Medical equipment
of Japan, the export license specified by the law
6 Please note that unless otherwise specified, we
is required for export. 6 Transportation equipment (vehicles, trains,
shall assume no responsibility whatsoever for any
ships, etc.)
conflict or dispute that may occur in connection
7 Traffic signal equipment with the effect of our and/or a third party’s
intellectual property rights and other related
8 Disaster prevention / crime prevention rights in consideration of your use of our products
equipment and/or information described or contained in our
catalogs. In this connection, no representation
9 Data-processing equipment shall be made to the effect that any third parties
are authorized to use the rights mentioned above
10 Application of similar complexity and/or
under licenses without our consent.
reliability requirements to the applications
listed above
7 No ozone depleting substances (ODS) under the
Montreal Protocol are used in our manufacturing
process.
www.murata.com