Professional Documents
Culture Documents
Ivry 4 1
Ivry 4 1
Ivry 4 1
Assembly instruction
B1 X1 C1 X1 T1 X1 F1 X17
flexible plywood inside Main frame Main frame transparent Main honey frame
B2 X2 C2 X1 T2 X1 F2 X36
F3 X18
front/back panel Flexible plywood inside Top frame transparent Bottom clips frame
B3 X1 C3 X2 T3 X2 F4 X16
Main frame Front/Back panel Front/Back panel transparent Wax paper sheet
B4 X1 C4 X1 T4 X2 ACCESSORIES
S1 X4
Foam insulation Flexible plywood outside Side panel transparent Closed entrance
B6 X2 C6 X2 T6 X1 E3 X1
Winter entrance
E4 X1
Plywood insulation panel Flexible plywood duble outside Main panel transparent Winter entrance
B7 X1 C7 X2 T7 X1 E5 X1
Serial number
W1 X20
Foam insulation Main Foam insulation panel Thin transparent paper Clamp
B8 X1 C8 X2 o
W3 X10
G2 27 C X2
Flexible plywood outside cover
Clamp
Flexible Plywood outside Plywood insulation panel Temp gauge
B9 X2
Leg G1 X1
B10 X4
Leg pin Glue
Beehive Structure
Cover
Transparent Cover
Frames
Base
Base Stage 1
Parts Tools
27
B1 B2
X1
X2
1 2 3
B2
B1
B1 B2
B1 B2
Hold part B1 against your body (as shown in Use one hand and gently bend the notches
Take part B1 and one part of B2 picture 3) gently bend and insert the wide long end of the part and slide the notches to the
tab inside the wide slot of part B2*Attension slots of prat B2 until they all in place.
B2 text side should be facing outside
4 5 6 B1
B1
B2
B2
Repeat steps 2+3 to the other side of B1 with Partially detach the notches of B1 from the Tightly re join parts B1 and B2.
the other B2 part. slots of B2 (start with one side) and put glue Repeat steps 5 to glue together the parts on
along all the joining points (as shown in the the other side.
picture).
E5
W1
B5 X2 X16
B3 B4
B6 X2
1 B3 2 3
B4
B3 B3
GLUE
Put glue on the lower parts Then, place the long side of the base in front Put glue on part B3 and attach B4 on top of B3
of the rim of parts B1+B2 (as shown in the of you and push the long side notches of B1 (as shown in the picture).
picture) and attach part B3 on top of them. into the matching slots of B3.
Start with inserting the notches of B2 to the Start from the middle ones and proceed
slots of B3 on both sides (like shown by the towards the edges. *** Make sure that all the
arrows) notches are properly inserted.
4 5 6
B5
B6
Use clamps (W1) to tighten together B3 and Put part B5 into place (as shown in the Apply Glue on flat rim of part B6, insert B6 *
B4 (as shown in the picture) until the glue is picture) from flat rim and push until notches enter to
completely dried. the slots. Add glue around B6 Repeat No 5,6
actions for the opposite side
W1
X14
B7 B8 B10
X4
1 2
B8
B7 B7
B9
Place the long side of the Base in front of you. Turn it upside down and put glue at the
spaces and in the slots of B3 *on both sides. (as shown in the picture) then insert the
notches of one side of B8 into the slots of B3 . Make sure that all the notches are properly
Put glue all over one side of part B9.
inserted.Put the isolation foam B7 in the space between B1 and B8 (as shown in the
picture).
4 5
B10
B8
C7
X2
C3
C1 C2
X2
C8
X2
1 2 3
C2
C2
C2
C1
C1 C1
Put glue in the slots of the long side of part C1 Place the long side of the parts in front of you Rotate the part on its side and put glue along
(as shown in the picture) then attach the wide and bend part C2 to insert the notches of its the spaces between the round notches of C2
notches of part C2 to the slots on one side of parallel side into the slots of the other side of and on part C1 (as shown in the picture).
C1 (as shown in the picture). C1. * important to follow the position in the as
in the illustation
4 5 6
C3
C1
7 8
C8
C8
C7
Put part C7 into place (as shown in the Apply Glue on flat rim of part C8, insert C8
picture) * start from flat trim and push until notches
enter to the slots. add glue around C8 Put aside, let glue to dry
Repeat No 7,8 actions for the opposite side Continue with-
Base Stage 3
Cover Stage 2
Continue with Parts Tools
C6
X2
W3 X8
C5
C4
W1 X8
1 2 C1 3
C3
C5 C4
C5 W3
Put glue along the line in and between the Use the Clamps W3 (as shown in the picture) Put the insolation foam in the space
notches on one side of C5 and on the rims of Put glue on the rim of part C1 between C2 and C5 (as shown in the
the two C3 parts (as shown in the picture). Then picture) and bend it in order to insert
attach one side of part C1 to one side of part C5 the notches to the slots of the other
by sliding its notches into the matching slots. side.
4 5 6
W1
C6
W1
Tighten the two parts together using W3 Put glue on the surface of part C6 then Tighten together parts C5 and C6 using the W1 clamps.
clamps (as shown in the picture). bend it and attach it to part C5. Make sure on Both sides of the cover.
that the notches are properly inserted to
the slots in the front of C3.
Repeat this step for the other side.
T6 T7
1 2 3 Ben
d
T2
T4
T1
T3
Put glue all over one side of part T1. Attach part T2 to T1 and tighten them together Put glue along the slots of parts T3
all around using W1 (as shown in the picture). and T4. Bend part T4 and attach
Leave aside to dry. them (as shown in the picture).
4 5 6
T4
T5 T6
T5
T5
T3
T1
T2 !
k
lic
C
Put glue in the rectangle slot formed attach T5 to T3 Make sure that the
from parts T1+T2 put inside it the pre- notches are properly inserted in T4.
glued T3+T4+T5 parts with part T3 Bend Part T6 and insert it into the cover (as shown
Repeat this step with the other T3+T4+T5
heading outside. Put glue all over the in the picture) and press the straight rims to lock
parts. them into the slots formed by T1/T2.
inner side of T3 peel the protective nylon Leave aside to dry.
from bouth sides of T5 Bend T7 and insert it inside of T6
when dry continue with no 6
Frames
Parts Tools
X17 F4 X16
F2 X36
F1
F3 X18
1 2 3
F1
Put glue in and along the lines of the 3 slots on Glue the frame clips (F2/F3) to the frame (as Take wax sheet and attach it to the frame
F1 (as shown in the picture). shown in the picture): by gently pressing it against the inner rim
F2 – on the right and left sides of the frame. of the frame. In case of need, you may
Make sure that the long / short parts of the soften the wax by mildly heating it.
clips are on the same side of the frame.
F3 – at the bottom of the frame.