Professional Documents
Culture Documents
MSDS BCDMH
MSDS BCDMH
Emergency Overview :
Hazards : No 8.3 in GB6944-86, Corrosive solid.
Routes of Entry : Skin Contact, Inhalation, Swallow
Health Hazards : Strong irritation to aspiration organs, eyes and skin. Dust inhalation can cause aspiration organs
reddening, cough, decompensation and lungs damage. Eyes contact can cause twinge, reddening and uncomfortable symptom
even irreversible eye damage and blindness. Skin contact for a long time may cause skin reddening, twinge and canker.
Environment Hazards : Correct utilization results no effects.
Explosion Danger : Produces irritative and choking gas (hydrogen bromide, hydrogen chloride/bromide gas and nitrogen
oxides) under strong light, fire and high temperature.
General Information: As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or
equivalent), and full protective gear. Strong oxidizer. Contact with combustible materials may cause a fire. During a fire,
irritating and highly toxic gases may be generated by thermal decomposition or combustion. Use water spray to keep
fire-exposed containers cool. Use water with caution and in flooding amounts. Contaminating or mixing with foreign materials
such as combustibles, grease, and fuels can cause fire. Containers may explode when heated.
Flash Point : No flash by standard methods.
Autoignition Temperature : N/A
Explosion Limits: N/A
Fire Extinguishing Media : Foam, dry ice, sand and water. DO NOT use CO2 or dry chemicals.
Storage : Keep away from heat, sparks, and flame. Keep away from sources of ignition. Do not store near combustible
materials. Keep container closed when not in use. Store in a tightly closed container. Store in a cool, dry, well-ventilated
area away from incompatible substances. Keep away from acids.
Storage Incompatibility : Segregate from acids, bases, oxidizers, reducing agents, organic chemicals.
Handling : Wash thoroughly after handling. Remove contaminated clothing and wash before reuse. Use only in a well ventilated
area. Minimize dust generation and accumulation. Do not get in eyes, on skin, or on clothing. Keep container tightly closed.
Avoid contact with heat, sparks and flame. Avoid contact with clothing and other combustible materials. Do not ingest or
inhale. Discard contaminated shoes.
Engineering Controls : Facilities storing or utilizing this material should be equipped with an eyewash facility and a
safety shower. Use adequate ventilation to keep airborne concentrations low.
Personal Protective Equipment :
Eyes : Wear safety glasses or goggles.
Skin : To prevent repeated or prolonged contact, wear impervious gloves (made from rubber, nitrile or neoprene).
Clothing : Wear appropriate protective clothing to minimize contact with skin.
Respirators: Dust respirator, if necessary, combined with an absorption cartridge. Be sure to use an approved/certified
respirator or equivalent.
Exposure Limits : Not available.
Acute effects :
LD50 (rat, oral) : 578 mg/kg
LD50 (rat, dermal) : >2,000 mg/kg
LC50 (rat) : 168mg/m3
Irritation : Corrosive to the skin. The primary skin irritation index was calculated to be 6.1.
Subsidiary and Chronic Toxicity : None.
Sensitization : Prolonged or repeated skin contact with solid BCDMH resulted in minor reddening of the skin and superficial
necrosis with the development of excessive exfoliation. Contact with dilute solutions of 0.1% or less was not irritating to
the skin. Eye contacts with BCDMH powder result in persistent severe conjunctival irritation and slow development of corneal
damage in rabbits. Washing the eye promptly resulted in a significant reduction of adverse effects. Dilute solutions of 0.1%
or less were non-irritating to the eyes.
Mutagenicity : Tested for potential mutagenic effects using Salmonella and Saccharomyces. All the results of the tests were
negative.
Deformity : No deformity to rat sperm.
Carcinogenicity : Not information found.
SECTION 12 - ECOLOGICAL INFORMATION
Processing, use or contamination of this product may change the waste management options. State and local disposal
regulations may differ from federal disposal regulations. Dispose of container and unused contents in accordance with
federal, state and local requirements.
Properties of Waster : Hazardous waster.
Waste disposal Methods : Control burning, absorb waste gas by limewater.
Note : Do not reuse package and container, control burning them as above mentioned.
IATA :
Proper shipping name : Oxidizing solid, corrosive, N.O.S.
UN Number : 3085
Hazard Class/Division: 5.1
Packing Category : Oxidizing solid.
Packing Group : II
Transportation Note : Prevent from high temperature, high moisture and straight sunlight.
Regulatory Information :
Based Classification and Labels of Dangerous Chemical Substances Commonly Used, GB13690-92 and Classification and Code
of Dangerous Goods, GB6944-86. BCDMH was classified as No. 8.3, Oxidative and corrosive solid.
Canadian Regulatory Information :
Class C : Oxidizing Material
Class D, Div 2b : Poisonous or Infectious Material: other toxic effects.
ALWAYS COMPLY WITH ALL APPLICABLE INTERNATIONAL, FEDERAL, STATE AND LOCAL REGULATIONS REGARDING THE TRANSPORTATION, STORAGE,
USE AND DISPOSAL OF THIS CHEMICAL.
Due to the changing nature of regulatory requirements, the REGULATORY INFORMATION listed in Section 15 of this document
should NOT be considered all-inclusive or authoritative. International, Federal, State and Local regulations should be
consulted to determine compliance with all required reporting requirements.
The information in this MSDS was obtained from sources which we believe are reliable. HOWEVER, THE INFORMATION IS PROVIDED
WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED, REGARDING ITS CORRECTNESS. The conditions or methods of handling, storage, use,
and disposal of the product are beyond our control and may be beyond our knowledge. FOR THIS AND OTHER REASONS, WE DO NOT
ASSUME RESPONSIBILITY AND EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE OR EXPENSE ARISING OUT OF OR IN ANY WAY CONNECTED
WITH THE HANDLING, STORAGE, USE OR DISPOSAL OF THE PRODUCT. This MSDS was prepared and is to be used only for this product.
If the product is used as a component in another product, this MSDS information may not be applicable.