Professional Documents
Culture Documents
Suitcase 8VS
Suitcase 8VS
2007−12
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
Description
Wire Feeder
SuitCase 8VS
Mil_Thank 4/05
TABLE OF CONTENTS
Directives
Standards
Arc Welding Equipment − Part 10: Electromagnetic Compatibility (EMC) Requirements. IEC 60974-10 August 2002
Arc Welding Equipment − Part 1: Welding Power Sources. IEC 60974-1 Ed. 2.1
Degrees Of Protection Provided By Enclosure (IP Code) IEC 60529 Ed. 2.1
The product technical file is maintained by the responsible Business Unit(s) located at the manufacturing facility.
dec_wire_1/07
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som _2007−04
7
Protect yourself and others from injury — read and follow these precautions.
D Always verify the supply ground − check and be sure that input
The symbols shown below are used throughout this manual power cord ground wire is properly connected to ground terminal in
to call attention to and identify possible hazards. When you disconnect box or that cord plug is connected to a properly
see the symbol, watch out, and follow the related instructions grounded receptacle outlet.
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information D When making input connections, attach proper grounding conduc-
found in the Safety Standards listed in Section 1-5. Read and tor first − double-check connections.
follow all Safety Standards. D Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
Only qualified persons should install, operate, maintain, and D Frequently inspect input power cord for damage or bare wiring −
repair this unit. replace cord immediately if damaged − bare wiring can kill.
D Turn off all equipment when not in use.
During operation, keep everybody, especially children, away. D Do not use worn, damaged, undersized, or poorly spliced cables.
D Do not drape cables over your body.
ELECTRIC SHOCK can kill. D If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Touching live electrical parts can cause fatal shocks D Do not touch electrode if you are in contact with the work, ground,
or severe burns. The electrode and work circuit is or another electrode from a different machine.
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also D Do not touch electrode holders connected to two welding ma-
live when power is on. In semiautomatic or automatic wire welding, the chines at the same time since double open-circuit voltage will be
wire, wire reel, drive roll housing, and all metal parts touching the present.
welding wire are electrically live. Incorrectly installed or improperly D Use only well-maintained equipment. Repair or replace damaged
grounded equipment is a hazard.
parts at once. Maintain unit according to manual.
D Do not touch live electrical parts. D Wear a safety harness if working above floor level.
D Wear dry, hole-free insulating gloves and body protection.
D Keep all panels and covers securely in place.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work D Clamp work cable with good metal-to-metal contact to workpiece
or ground. or worktable as near the weld as practical.
D Do not use AC output in damp areas, if movement is confined, or if D Insulate work clamp when not connected to workpiece to prevent
there is a danger of falling. contact with any metal object.
D Use AC output ONLY if required for the welding process. D Do not connect more than one electrode or work cable to any
D If AC output is required, use remote output control if present on single weld output terminal.
unit.
D Additional safety precautions are required when any of the follow-
SIGNIFICANT DC VOLTAGE exists in inverter-type
ing electrically hazardous conditions are present: in damp welding power sources after removal of input
locations or while wearing wet clothing; on metal structures such power.
as floors, gratings, or scaffolds; when in cramped positions such D Turn Off inverter, disconnect input power, and discharge input
as sitting, kneeling, or lying; or when there is a high risk of unavoid- capacitors according to instructions in Maintenance Section
able or accidental contact with the workpiece or ground. For these before touching any parts.
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit volt- HOT PARTS can cause severe burns.
age. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone! D Do not touch hot parts bare handed.
D Disconnect input power or stop engine before installing or D Allow cooling period before working on gun or
servicing this equipment. Lockout/tagout input power according to torch.
OSHA 29 CFR 1910.147 (see Safety Standards). D To handle hot parts, use proper tools and/or
D Properly install and ground this equipment according to its wear heavy, insulated welding gloves and
Owner’s Manual and national, state, and local codes. clothing to prevent burns.
OM-1599 Page 1
D Do not use welder to thaw frozen pipes.
FUMES AND GASES can be hazardous.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your D Wear oil-free protective garments such as leather gloves, heavy
health. shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
D Keep your head out of the fumes. Do not breathe the fumes. from your person before doing any welding.
D If inside, ventilate the area and/or use local forced ventilation at the D After completion of work, inspect area to ensure it is free of sparks,
arc to remove welding fumes and gases. glowing embers, and flames.
D If ventilation is poor, wear an approved air-supplied respirator. D Use only correct fuses or circuit breakers. Do not oversize or by-
pass them.
D Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables, D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
coatings, cleaners, and degreasers. for hot work and have a fire watcher and extinguisher nearby.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watch-
FLYING METAL or DIRT can injure eyes.
person nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breath- D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
ing air is safe.
they can throw off slag.
D Do not weld in locations near degreasing, cleaning, or spraying op-
D Wear approved safety glasses with side
erations. The heat and rays of the arc can react with vapors to form
shields even under your welding helmet.
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
BUILDUP OF GAS can injure or kill.
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements D Shut off shielding gas supply when not in use.
can give off toxic fumes if welded. D Always ventilate confined spaces or use
approved air-supplied respirator.
OM-1599 Page 3
1-4. California Proposition 65 Warnings
For Gasoline Engines:
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to Engine exhaust contains chemicals known to the State of
cause birth defects and, in some cases, cancer. (California California to cause cancer, birth defects, or other reproduc-
Health & Safety Code Section 25249.5 et seq.) tive harm.
For Diesel Engines:
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of Diesel engine exhaust and some of its constituents are
California to cause cancer and birth defects or other known to the State of California to cause cancer, birth
reproductive harm. Wash hands after handling. defects, and other reproductive harm.
Welding current, as it flows through welding cables, will cause electro- 2. Arrange cables to one side and away from the operator.
magnetic fields. There has been and still is some concern about such
3. Do not coil or drape cables around your body.
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National 4. Keep welding power source and cables as far away from opera-
Research Council concluded that: “The body of evidence, in the tor as practical.
committee’s judgment, has not demonstrated that exposure to power-
5. Connect work clamp to workpiece as close to the weld as possi-
frequency electric and magnetic fields is a human-health hazard.”
ble.
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you About Implanted Medical Devices:
may wish to minimize your exposure to electromagnetic fields when Implanted Medical Device wearers should consult their doctor and the
welding or cutting. device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
To reduce magnetic fields in the workplace, use the following If cleared by your doctor, then following the above procedures is recom-
procedures: mended.
OM-1599 Page 4
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
fre_som_2007−04
7
Se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
DANGER! − Indique une situation dangereuse qui si on . Indique des instructions spécifiques.
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dan-
gers possibles sont montrés par les symboles joints ou Ce groupe de symboles veut dire Avertissement! Attention! DANGER
sont expliqués dans le texte. DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
NOTE − Indique des déclarations pas en relation avec des blessures afférant pour les actions nécessaires afin d’éviter le danger.
personnelles.
LES RAYONS DE L’ARC peuvent pro D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
voquer des brûlures dans les yeux e
sur la peau. D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intense D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
(ultraviolets et infrarouges) susceptibles de provoquer des brûlure
dans les yeux et sur la peau. Des étincelles sont projetées pendant le D Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
soudage. NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
D Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pendant le soudage
(voir ANSI Z49.1 et Z87.1 énuméré dans les normes de sécurité). DES PIECES DE METAL ou DES SA-
D Porter des lunettes de sécurité avec écrans latéraux même sous LETES peuvent provoquer des bles-
votre casque. sures dans les yeux.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements D Le soudage, l’écaillement, le passage de la pièce à la brosse en
et les étincelles ; prévenir toute personne sur les lieux de ne pas fil de fer, et le meulage génèrent des étincelles et des particules
regarder l’arc. métalliques volantes. Pendant la période de refroidissement des
soudures, elles risquent de projeter du laitier.
D Porter des vêtements confectionnés avec des matières résistan- D Porter des lunettes de sécurité avec écrans latéraux ou un écran
tes et ignifuges (cuir, coton lourd ou laine) et des bottes de facial.
protection.
OM-1599 Page 6
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive,
LES ACCUMULATIONS DE GAZ des chocs mécaniques, des dommages physiques, du laitier, des
risquent de provoquer des blessures flammes ouvertes, des étincelles et des arcs.
ou même la mort.
D Fermer l’alimentation du gaz protecteur en cas D Placer les bouteilles debout en les fixant dans un support station-
de non-utilisation. naire ou dans un porte-bouteilles pour les empêcher de tomber ou
D Veiller toujours à bien aérer les espaces confi- de se renverser.
nés ou se servir d’un respirateur d’adduction
d’air homologué. D Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
LES CHAMPS MAGNETIQUES peuv-
ent affecter des implants médicaux. D Ne jamais placer une torche de soudage sur une bouteille à gaz.
D Porteur de simulateur cardiaque ou autre im- D Une électrode de soudage ne doit jamais entrer en contact avec
plants médicaux, rester à distance. une bouteille.
D Les porteurs d’implants doivent d’abord consulter leur médecin
avant de s’approcher des opérations de soudage à l’arc, de sou- D Ne jamais souder une bouteille pressurisée − risque d’explosion.
dage par points, de gougeage, du coupage plasma ou de chauf-
fage par induction. D Utiliser seulement des bouteilles de gaz protecteur, régulateurs,
tuyaux et raccords convenables pour cette application spécifique ;
LE BRUIT peut endommager l’ouïe. les maintenir ainsi que les éléments associés en bon état.
Le bruit des processus et des équipements peut D Détourner votre visage du détendeur-régulateur lorsque vous
affecter l’ouïe. ouvrez la soupape de la bouteille.
D Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé. D Le couvercle du détendeur doit toujours être en place, sauf lorsque
la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
LES BOUTEILLES peuvent exploser D Utiliser les équipements corrects, les bonnes procédures et suffi-
si elles sont endommagées. samment de personnes pour soulever et déplacer les bouteilles.
Des bouteilles de gaz protecteur contiennent du gaz
sous haute pression. Si une bouteille est endomma- D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
gée, elle peut exploser. Du fait que les bouteilles de l’équipement connexe et le dépliant P-1 de la CGA (Compressed
gaz font normalement partie du procédé de sou- Gas Association) mentionné dans les principales normes de sécu-
dage, les manipuler avec précaution. rité.
OM-1599 Page 7
LES FILS DE SOUDAGE peuvent LE RAYONNEMENT HAUTE FRÉ-
provoquer des blessures. QUENCE (H.F.) risque de provoquer
D Ne pas appuyer sur la gâchette avant d’en des interférences.
avoir reçu l’instruction. D Le rayonnement haute fréquence (H.F.) peut
D Ne pas diriger le pistolet vers soi, d’autres per- provoquer des interférences avec les équipe-
sonnes ou toute pièce mécanique en enga- ments de radio−navigation et de communica-
geant le fil de soudage. tion, les services de sécurité et les ordinateurs.
D Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installa-
tion.
DES ORGANES MOBILES peuvent D L’utilisateur est tenu de faire corriger rapidement par un électricien
provoquer des blessures. qualifié les interférences résultant de l’installation.
D S’abstenir de toucher des organes mobiles tels D Si le FCC signale des interférences, arrêter immédiatement l’ap-
que des ventilateurs. pareil.
D Maintenir fermés et verrouillés les portes, pan-
neaux, recouvrements et dispositifs de protec- LE SOUDAGE À L’ARC risque de
tion. provoquer des interférences.
D Seules des personnes qualifiées sont autorisées à enlever les
portes, panneaux, recouvrements ou dispositifs de protection D L’énergie électromagnétique risque de provo-
pour l’entretien. quer des interférences pour l’équipement élec-
tronique sensible tel que les ordinateurs et l’é-
D Remettre les portes, panneaux, recouvrements ou dispositifs de quipement commandé par ordinateur tel que
protection quand l’entretien est terminé et avant de rebrancher
les robots.
l’alimentation électrique.
D Veiller à ce que tout l’équipement de la zone de soudage soit
compatible électromagnétiquement.
LIRE LES INSTRUCTIONS. D Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
D Lisez le manuel d’instructions avant l’utilisation aussi bas que possible (ex. par terre).
ou la maintenance de l’appareil. D Veiller à souder à une distance de 100 mètres de tout équipe-
D N’utiliser que les pièces de rechange recom- ment électronique sensible.
mandées par le constructeur. D Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
D Effectuer régulièrement le contrôle et l’entretien de l’installation. D En cas d’interférences après avoir pris les mesures précéden-
D Maintenir soigneusement fermés les portes et les panneaux des tes, il incombe à l’utilisateur de prendre des mesures supplé-
sources de haute fréquence, maintenir les éclateurs à une distan- mentaires telles que le déplacement du poste, l’utilisation de câ-
ce correcte et utiliser une terre et un blindage pour réduire les bles blindés, l’utilisation de filtres de ligne ou la pose de protec-
interférences éventuelles. teurs dans la zone de travail.
OM-1599 Page 8
2-5. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, L4W 5NS (téléphone : 800-463-6727 ou à Toronto 416-747-4044, site
de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www.csa-international.org).
Internet : www.global.ihs.com).
Safe Practice For Occupational And Educational Eye And Face Protec-
Recommended Safe Practices for the Preparation for Welding and Cut- tion, ANSI Standard Z87.1, de American National Standards Institute,
ting of Containers and Piping, American Welding Society Standard 11 West 43rd Street, New York, NY 10036-8002 (téléphone :
AWS F4.1 de Global Engineering Documents (téléphone : 212-642-4900, site Internet : www.ansi.org).
1-877-413-5184, site Internet : www.global.ihs.com). Standard for Fire Prevention During Welding, Cutting, and Other Hot
National Electrical Code, NFPA Standard 70, de National Fire Protec- Work, NFPA Standard 51B, de National Fire Protection Association,
tion Association, P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : 617-770-3000,
617-770-3000, site Internet : www.nfpa.org). site Internet : www.nfpa.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, OSHA, Occupational Safety and Health Standards for General Indus-
de Compressed Gas Association, 4221 Walney Road, 5th Floor, Chan- try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
tilly, VA 20151 (téléphone : 703-788-2700, site Internet : and Part 1926, Subpart J, de U.S. Government Printing Office, Superin-
www.cganet.com). tendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(téléphone : 1-866-512-1800) (il y a 10 bureaux régionaux−−le télépho-
Code for Safety in Welding and Cutting, CSA Standard W117.2, de ne de la région 5, Chicago, est 312-353-2220, site Internet :
Canadian Standards Association, 5060 Mississauga, Ontario, Canada www.osha.gov).
OM-1599 Page 9
OM-1599 Page 10
SECTION 3 − DEFINITIONS
+ injure skin.
4.1 Wear hat and safety glasses.
Use ear protection and button
shirt collar. Use welding
S-178 936
helmet with correct shade of
filter. Wear complete body
protection.
5 Become trained and read the
instructions before working on
the machine or welding.
6 Do not remove or paint over
(cover) the label.
OM-1599 Page 11
3-2. Manufacturer’s Rating Label For CE Products
1 Rating Label - Typical
(Located Inside Cover)
Use rating label to determine input
power needs.
802 705-B
Output Input
A Amperes
V Volts
Read Instructions
U1 Primary Voltage
U2 Conventional Load
Voltage Hz Hertz
I1 Primary Current
OM-1599 Page 12
SECTION 4 − INSTALLATION
4-1. Specifications
Welding Input
Type of Wire Feed Wire Type Max. Wire
Power Welding IP Overall
Input Speed And Spool Weight
Source Circuit Rating Dimensions
Power Range Diameter Capacity
Type Rating
Solid Steel:
.023 − .062 in Length: 15-5/8 in
Constant 50 − 700 ipm (0.6 − 1.6 mm); (397 mm)
Open-Circuit/
Voltage (CV) (1.3 − 18 Stainless Steel: 330 Amperes
Arc Voltage, 14 lb (6.4 kg), Width: 6-1/2 in 25 lb
Or Constant mpm) .023 − .052 in At 60% 23
15 − 100 8 in (203 mm) (165 mm) (11 kg)
Current (CC) Depending On (0.6 − 1.3 mm); Duty Cycle
Volts DC Height: 14-1/2 in
DC Arc Voltage Flux Cored:
.030 − .052 in (368 mm)
(0.8 − 1.3 mm)
4 6
8
7 803 625-B
OM-1599 Page 13
4-4. Installing And Aligning Wire Guide And Drive Rolls
Installing Wire Guide And Drive
Rolls:
1 Drive Roll Nut
2 Drive Roll Carrier
Turn nut one click until lobes of nut
line up with lobes of drive roll carrier.
3 Drive Roll
Slide drive roll onto drive roll carrier.
Turn nut one click.
Repeat procedure for top drive roll.
4 Inlet Wire Guide Screw
5 Inlet Wire Guide
(One Piece Anti-Wear)
. The factory installed inlet wire
guide is good for up to 5/64
Installing Wire Guide inch diameter wire.
And Drive Rolls Loosen securing screw. Align inlet
guide so inlet guide screw is
centered in groove in guide, or so tip
is as close to drive rolls as possible
without touching. Tighten screw.
5 Aligning Wire Guide And Drive
4 Rolls:
View is from top of drive rolls look-
ing down with pressure assembly
open.
6 Drive Roll Securing Nut
3 7 Drive Roll
1 8 Wire Guide
9 Welding Wire
2 10 Drive Gear
Turn screw in or out until drive roll
groove lines up with wire guide.
Close pressure roll assembly.
Only bottom drive roll alignment is
adjustable. Turn adjustment screw
in or out until groove in drive roll
Aligning Wire Guide And Drive Rolls lines up with wire guide as shown.
Cleaning Drive Rolls:
Remove drive rolls, and clean
grooves using a wire brush.
Correct Incorrect
8 9
7
6
10
Tools Needed:
3/16 in
3/8 in
802 706-B / Ref. 132 808-F / Ref. 162 079-A / Ref. 180 967
OM-1599 Page 14
4-5. Connecting Welding Gun And Voltage Sensing Clamp
! Turn Off wire feeder and
welding power source. Stop
engine on welding
generator.
2
1 Gun Securing Knob
1 2 Gun Block
3 Gun Outlet Wire Guide
Loosen knob, insert gun end into
block. Position outlet wire guide as
close as possible to drive rolls with-
out touching. Tighten knob.
4 Gun Trigger Plug
5 Gun Trigger Receptacle
6 Voltage Sensing Clamp
Internal Side View 3 Connect voltage sensing clamp to
workpiece.
Tools Needed:
5/8 in
1
801 155-A / Ref. 802 770
OM-1599 Page 15
4-7. Connecting Weld Cable
! Turn Off wire feeder and
Internal Side View welding power source. Stop
engine on welding
generator.
1 User-Suppled Weld Cable
From Wire Feeder
Follow wire manufacturer’s recom-
mendations for weld cable polarity.
2 User-Suppled Male Connector
3 User-Suppled Female
Connector
Push female connector over male
connector, and turn 1/4 turn clock-
1 2 wise.
3
Ref. 132 808-F / Ref. 802 706-B
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
Not Exceeding***
Weld Output
Terminals
150 3 (30) 3 (30) 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 3/0 (95)
200 3 (30) 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120) 4/0 (120)
2 ea. 2/0 2 ea. 3/0 2 ea. 4/0 3 ea. 3/0 3 ea. 3/0
500 2/0 (70) 3/0 (95) 4/0 (120)
(2x70) (2x95) (2x120) (3x95) (3x95)
* This chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
( ) = mm2 for metric use S-0007-F−
***For distances longer than those shown in this guide, call a factory applications representative at 920-735-4505.
OM-1599 Page 16
4-9. Installing And Threading Welding Wire
Installing Wire And Adjusting
. Hold wire tightly to keep Hub Tension:
it from unraveling. 1 Retaining Nut
2 Hub Tension Adjustment Nut
Remove retaining ring, and install
spool so hub pin fits spool hole. Re-
install retaining nut.
Adjust tension nut so only a slight
force is needed to turn spool.
Threading Welding Wire:
3 Pressure Assembly
Adjustment Knob
Lay gun cable out straight.
Open pressure assembly, hold wire
tightly, and cut off end. Push wire
through guides into gun.
3 Close and tighten pressure assem-
bly. Press Jog switch until wire
comes out gun.
Feed wire against wooden surface,
and tighten knob so wire does not
1 slip.
2
Cut off wire, and close door.
6 in
(150 mm)
WOOD
OM-1599 Page 17
SECTION 5 − OPERATION
5-1. Controls For Non-CE Models
1 Power Control Switch
2 Trigger Hold Switch (Optional)
This unit offers an optional trigger
3 2 hold function, which is turned On or
1
Off with a front panel toggle switch.
Depress the upper part of the switch
(turns trigger hold On) to weld with-
out holding gun trigger throughout
the weld cycle.
To start weld, press and release gun
trigger. To end weld, press and re-
lease gun trigger.
PURGE TRIGGER POWER
Depress the lower part of the trigger
HOLD hold switch to turn trigger hold Off.
8
3 Purge Switch
Press switch to momentarily ener-
gize gas solenoid and purge air from
gun, and to adjust shielding gas regu-
9 lator.
OM-1599 Page 18
5-2. Controls For CE Models
1 Power Control Switch
2 Trigger Hold Switch
Depress the upper part of the
3 2 1 switch (turns trigger hold On) to
weld without holding gun trigger
throughout the weld cycle.
To start weld, press and release
gun trigger. To end weld, press and
release gun trigger.
Depress the lower part of the trigger
hold switch to turn trigger hold Off.
3 Purge Switch
Press switch to momentarily ener-
gize gas solenoid and purge air
from gun, and to adjust shielding
gas regulator.
4 Wire Speed Control
Use control to adjust wire speed
4 within range selected by switch.
5 Jog Switch
Use Jog position to momentarily
feed welding wire at speed set on
Wire Speed control without ener-
gizing welding circuit or shielding
gas valve.
6 HI/LO Range Switch
Use switch to select high or low wire
Front Panel speed range. High range is 100 to
700 ipm. Low range is 50 to 350
ipm.
7 CC/CV Switch
Use switch to match wire feeder
with welding power source output.
Close and latch door.
5 6 7
LO CC
HI CV
Internal Control Panel
Ref. 803 626-A / Ref. 802 706-B / Ref. 203 745 / Ref. 203 749
OM-1599 Page 19
SECTION 6 − MAINTENANCE & TROUBLESHOOTING
6-1. Routine Maintenance
3 Months
Replace
Damaged Or Replace Damaged
Unreadable Gas Hose
Labels
Repair Or Replace
Cracked Cables
And Cords
6 Months
Clean
Blow Out Or
Drive
Vacuum Inside
Rolls
OM-1599 Page 20
6-3. Troubleshooting
Trouble Remedy
Wire does not feed; open-circuit voltage Check circuit breaker CB1. Reset CB1.
available.
Wire feeds as soon as power is applied. Check gun trigger. See gun Owner’s Manual.
Wire feeds when Jog switch is pressed Check gun trigger connection at wire feeder. Check gun trigger leads and trigger switch. See gun Owner’s
but not when gun trigger is pressed. Manual.
Wire stubbing on low end using a con- Make sure CC/CV switch is in CC position (see Section 5-1).
stant current power source.
Gas does not flow or does not stop flow- Check gas valve.
ing; wire feeds.
Wire remains energized after trigger is Check contactor W1 to see if contacts are frozen closed.
released.
OM-1599 Page 21
SECTION 7 − ELECTRICAL DIAGRAMS
203 029−E
OM-1599 Page 23
SECTION 8 − PARTS LIST
. Hardware is common and
not available unless listed.
1
62 63
64 2
51 52
50
4
66
5
53 69
54
7
55
49 56 8
57
48 65 5
58
59
47 60 67 9
61
46
68
45
42 13
12
44
41 11 10
14
40
43 15
39
17
16
38
18 19
20
37
21
22
23
31
32
36
35
34
33
24
25
30 26 802 675-G
29 27
28 Figure 8-1. Complete Assembly
OM-1599 Page 24
Item Dia. Part
No. Mkgs. No. Description Quantity
OM-1599 Page 25
Item Dia. Part
No. Mkgs. No. Description Quantity
OM-1599 Page 26
Figure 8-2. Drive Roll & Wire Guide Kits (2 Drive Roll)
OM-1599 Page 27
Notes
OHM’S LAW
VOLTAGE =
CURRENT X RESISTANCE
CURRENT = VOLTAGE
RESISTANCE
RESISTANCE = VOLTAGE
CURRENT
OM-1599 Page 28
Notes
229895
MATERIAL THICKNESS GAUGE
Notes
Distributor
Address
City
State Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Contact the Delivering Carrier to: File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.