Professional Documents
Culture Documents
638 - New-En
638 - New-En
638 - New-En
LOCTITE® 638™
June-2022
PRODUCT DESCRIPTION
LOCTITE® 638™ provides the following product characteristics:
Cure Speed vs. Bond Gap
Technology Acrylic
The rate of cure will depend on the bondline gap. The following graph
Chemical Type Urethane methacrylate shows shear strength developed with time @ 23°C on steel pins and
Appearance (uncured) Green liquid collars at different controlled gaps and tested according to ISO 10123.
Fluorescence Positive under UV light
Viscosity High 100
25
Cure Speed vs. Substrate
The rate of cure will depend on the substrate used. The graph below 0
shows the shear strength developed with time @ 23°C on steel pins 5m 10m 30m 1h 4h 8h 24h 72h 168h
and collars compared to different materials and tested according to Cure Time
ISO 10123.
100
% of Full Strength on Steel
Steel
Cure Speed vs. Activator
The graph below shows the shear strength developed with time @ 23
75 on stainless steel pins and collars using Activator SF 7471™, SF
Stainless steel 7649™ and SF 7091™ and tested according to ISO 10123.
50
Aluminum
25
0
5m 10m 30m 1h 4h 8h 24h 72h 168h
Cure Time
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 638™, June-2022
% of Full Strength on Steel 125 Hot Strength
Tested at temperature
100 125
1™
% Strength @ 23 °C
75 F 747 100
™
91 vat or S
70 cti SF 7649
™
F A Activato
r 75
50
torS
t iva
Ac No activator 50
25
25
0
5m 10m 30m 1h 4h 8h 24h 72h 168h
Cure Time 0
-25 0 25 50 75 100 125 150 175 200
Temperature, °C
Cold Strength
This product has been tested to -75°C (-100 F). This product may work
below this temperature, but has not been tested.
TYPICAL PERFORMANCE OF CURED MATERIAL
Heat Aging
Physical Properties Aged at temperature indicated and tested @ 23 °C
Cured for 24 hours @ 23 °C 200
Glass Transition Temperature ISO 11359-2, °C 76
175 120 °C
Coefficient of Thermal Expansion,
% Strength @ 23 °C
ISO 11359-2, K-1 150 150 °C
Below Tg 96×10-06
125
Above Tg 192×10-06
100
Adhesive Properties
75 180 °C
Cured for 15 minutes @ 23°C
Compressive Shear Strength, ISO 10123: 50
Steel pins and collars N/mm² 13.5 200 °C
(psi) (1,960) 25
Cured for 72 hours @ 23°C 0
Compressive Shear Strength, ISO 10123: 0 1000 2000 3000 4000 5000
Steel pins and collars N/mm² 29 Exposure Time, hours
(psi) (4,200)
Stainless Steel pins and collars N/mm² 28 Chemical/Solvent Resistance
(psi) (4,000) Aged under conditions indicated and tested @ 23°C
Aluminum pins and collars N/mm² 17 % of initial strength
(psi) (2,710) Environment °C 500 h 1000 h 3000 h 5000 h
Motor oil 125 175 165 165 165
Cured for 72 hours @ 23°C (5W40 -Synthetic)
Breakaway Torque, ISO 10964: Unleaded Petrol 23 105 105 105 105
M10 black oxide bolts and mild steel N·m 57 Brake fluid 23 120 115 115 115
nuts (lb.in.) (510)
3/8 x 16 steel nuts (grade 2) and bolts N·m 25 Water/glycol 50/50 87 145 145 145 145
(grade5) (lb.in.) (220) Ethanol 23 110 110 100 100
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m: Stainless Steel pins and collars
3/8 x 16 steel nuts (grade 2) and bolts N·m 23 % of initial strength
(grade5) (lb.in.) (210)
Environment °C 500 h 1000 h 3000 h 5000 h
Prevail Torque, ISO 10964, Pre-torqued to 5 N·m: Sodium Hydroxide, 20% 23 115 105 95 90
3/8 x 16 steel nuts and bolts N·m 12 Phosphoric Acid, 10% 23 75 60 40 35
(lb.in.) (110)
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 638™, June-2022
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 638™, June-2022
Trademark usage
Except as otherwise noted, all trademarks in this document are
trademarks of Henkel Corporation in the U.S. and elsewhere. ®
denotes a trademark registered in the U.S. Patent and Trademark
Office.
For the most direct access to local sales and technical support visit: www.henkel.com/industrial