Professional Documents
Culture Documents
NCP1117 D
NCP1117 D
NCP1117 D
www.onsemi.com
NCV1117 Tab
The NCP1117 series are low dropout positive voltage regulators that
are capable of providing an output current that is in excess of 1.0 A 123
with a maximum dropout voltage of 1.2 V at 800 mA over SOT−223
temperature. This series contains nine fixed output voltages of 1.5 V, (Top View)
1.8 V, 1.9 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 5.0 V, and 12 V that have no
minimum load requirement to maintain regulation. Also included is an Tab
adjustable output version that can be programmed from 1.25 V to
18.8 V with two external resistors. On chip trimming adjusts the
reference/output voltage to within ±1.0% accuracy. Internal protection
2
features consist of output current limiting, safe operating area 1 3
compensation, and thermal shutdown. The NCP1117 series can DPAK
operate with up to 20 V input. Devices are available in SOT−223 and (Top View)
DPAK packages.
Pin: 1. Adjust/Ground
Features 2. Output
• Output Current in Excess of 1.0 A 3. Input
• 1.2 V Maximum Dropout Voltage at 800 mA Over Temperature Heatsink tab is connected to Pin 2.
• Fixed Output Voltages of 1.5 V, 1.8 V, 1.9 V, 2.0 V, 2.5 V, 2.85 V,
3.3 V, 5.0 V, and 12 V ORDERING INFORMATION
• Adjustable Output Voltage Option See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
• No Minimum Load Requirement for Fixed Voltage Output Devices
• Reference/Output Voltage Trimmed to ±1.0% DEVICE MARKING INFORMATION
• Current Limit, Safe Operating and Thermal Shutdown Protection See general marking information in the device marking
section on page 14 of this data sheet.
• Operation to 20 V Input
• NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
• These are Pb-Free Devices
Applications
• Consumer and Industrial Equipment Point of Regulation
• Active SCSI Termination for 2.85 V Version
• Switching Power Supply Post Regulation
• Hard Drive Controllers
• Battery Chargers
TYPICAL APPLICATIONS
110 W
3 NCP1117 2 110 W
Input 3 NCP1117 2 Output Input 3 2 Output
NCP1117 XT285 18 to 27
XTXX XTA 10 + + 22
110 W
10 + + 10 10 + + 10
1 Lines
mF mF
mF 1 mF mF 1 mF
4.75 V +
to 110 W
5.25 V
MAXIMUM RATINGS
Rating Symbol Value Unit
Input Voltage (Note 1) Vin 20 V
Output Short Circuit Duration (Notes 2 and 3) − Infinite −
Power Dissipation and Thermal Characteristics
Case 318H (SOT−223)
Power Dissipation (Note 2) PD Internally Limited W
Thermal Resistance, Junction−to−Ambient, Minimum Size Pad RqJA 160 °C/W
Thermal Resistance, Junction−to−Case RqJC 15 °C/W
Case 369A (DPAK)
Power Dissipation (Note 2) PD Internally Limited W
Thermal Resistance, Junction−to−Ambient, Minimum Size Pad RqJA 67 °C/W
Thermal Resistance, Junction−to−Case RqJC 6.0 °C/W
www.onsemi.com
2
NCP1117, NCP1117I, NCV1117
ELECTRICAL CHARACTERISTICS
(Cin = 10 mF, Cout = 10 mF, for typical value TA = 25°C, for min and max values TA is the operating ambient temperature range that applies
unless otherwise noted.) (Note 4)
Characteristic Symbol Min Typ Max Unit
Reference Voltage, Adjustable Output Devices Vref V
(Vin–Vout = 2.0 V, Iout = 10 mA, TA = 25°C) 1.238 1.25 1.262
(Vin–Vout = 1.4 V to 10 V, Iout = 10 mA to 800 mA) (Note 4) 1.225 − 1.270
Output Voltage, Fixed Output Devices Vout V
1.5 V (Vin = 3.5 V, Iout = 10 mA, TA = 25 °C) 1.485 1.500 1.515
(Vin = 2.9 V to 11.5 V, Iout = 0 mA to 800 mA) (Note 4) 1.470 − 1.530
www.onsemi.com
3
NCP1117, NCP1117I, NCV1117
www.onsemi.com
4
NCP1117, NCP1117I, NCV1117
2.0 2.0
TJ = 25°C
1.8
1.5
1.6
1.0
1.4
0.5
1.2
Vin = 5.0 V
Load pulsed at 1.0% duty cycle Load pulsed at 1.0% duty cycle
0 1.0
0 2 4 6 8 10 12 14 16 18 20 −50 −25 0 25 50 75 100 125 150
Vin − Vout, VOLTAGE DIFFERENTIAL (V) TA, AMBIENT TEMPERATURE (°C)
Figure 6. Output Short Circuit Current Figure 7. Output Short Circuit Current
vs. Differential Voltage vs. Temperature
100
IQ, QUIESCENT CURRENT CHANGE (%)
10
Iadj, ADJUST PIN CURRENT (mA)
5.0
80
0
60
−5.0
40
−10
20
Iout = 10 mA −15
0 −20
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)
www.onsemi.com
5
NCP1117, NCP1117I, NCV1117
100 100
Vripple v 3.0 VP−P Vripple v 0.5 VP−P
fripple = 120 Hz
60 60
fripple = 20 kHz
Vout = 5.0 V
Vripple v 0.5 VP−P
Vin − Vout = 3.0 V
40 40 Iout = 0.5 A Vin − Vout w Vdropout
Vout = 5.0 V
Cout = 10 mF
Vin − Vout = 3.0 V
Cadj = 25 mF, f > 60 Hz
Cout = 10 mF
20 20 Cadj = 200 mF, f v 60 Hz
Cadj = 25 mF
TA = 25°C
TA = 25°C
0 0
0 200 400 600 800 1000 10 100 1.0 k 10 k 100 k
Iout, OUTPUT CURRENT (mA) fripple, RIPPLE FREQUENCY (Hz)
Figure 10. NCP1117XTA Ripple Rejection Figure 11. NCP1117XTA Ripple Rejection
vs. Output Current vs. Frequency
Region of Instability
1 0.1
Region of Instability
0.1 0.01
0.001 0.01 0.1 1 10 0 100 200 300 400 500 600 700 800 900 1000
350E−9
1A Cin = 10 mF Tantalum
300E−9 Cout = 10 mF Tantalum
0.5 A Vin − Vout = 3.0 V
250E−9
V/sqrt (Hz)
200E−9
0.1 A
150E−9
100E−9
50E−9
0
10 100 1.0 k 10 k 100 k
FREQUENCY (Hz)
www.onsemi.com
6
NCP1117, NCP1117I, NCV1117
OUTPUT VOLTAGE
DEVIATION (V)
VOLTAGE (V) Cin = 1.0 mF
Cout = 10 mF 0.1
INPUT
Iout = 0.1 A 0
5.25
TA = 25°C
4.25 −0.1 Cin = 10 mF
Cout = 10 mF
Vin = 4.5 V
OUTPUT VOLTAGE
DEVIATION (mV)
LOAD CURRENT
Preload = 0.1 A
20
CHANGE (A)
TA = 25°C
0 0.5
−20 0
OUTPUT VOLTAGE
DEVIATION (V)
Cin = 1.0 mF
VOLTAGE (V)
Cout = 10 mF 0.1
INPUT
Iout = 0.1 A
7.5 0
TA = 25°C
6.5 −0.1 Cin = 10 mF
Cout = 10 mF
Vin = 6.5 V
OUTPUT VOLTAGE
LOAD CURRENT
DEVIATION (mV)
Preload = 0.1 A
CHANGE (A)
20 TA = 25°C
0 0.5
−20 0
Cin = 1.0 mF
VOLTAGE (V)
Cout = 10 mF 0.1
INPUT
Iout = 0.1 A
14.5 0
TA = 25°C
13.5 −0.1 Cin = 10 mF
Cout = 10 mF
Vin = 13.5 V
OUTPUT VOLTAGE
LOAD CURRENT
DEVIATION (mV)
20 Preload = 0.1 A
CHANGE (A)
TA = 25°C
0 0.5
−20 0
www.onsemi.com
7
NCP1117, NCP1117I, NCV1117
JUNCTION−TO−AIR (°CW)
PD(max) for TA = 50°C
140 1.2
ÎÎÎ
2.0 oz. Copper
Minimum L
ÎÎÎ
120 1.0
Size Pad
ÎÎÎ
L
100 0.8
80 0.6
RqJA
60 0.4
0 5.0 10 15 20 25 30
L, LENGTH OF COPPER (mm)
1.4
JUNCTION−TO−AIR (°CW)
90
80
Minimum
ÎÎÎÎ
2.0 oz. Copper
ÎÎÎÎ
L 1.2
ÎÎÎÎ
70 Size Pad 1.0
L
60
50
ÎÎÎÎ 0.8
0.6
RqJA
40 0.4
0 5.0 10 15 20 25 30
L, LENGTH OF COPPER (mm)
www.onsemi.com
8
NCP1117, NCP1117I, NCV1117
APPLICATIONS INFORMATION
www.onsemi.com
9
NCP1117, NCP1117I, NCV1117
Protection Diodes The second condition is that the ground end of R2 should be
The NCP1117 family has two internal low impedance connected directly to the load. This allows true Kelvin
diode paths that normally do not require protection when sensing where the regulator compensates for the voltage
used in the typical regulator applications. The first path drop caused by wiring resistance RW −.
connects between Vout and Vin, and it can withstand a peak
surge current of about 15 A. Normal cycling of Vin cannot Input 3 NCP1117 2 RW+ Output
generate a current surge of this magnitude. Only when Vin XTA
+ Remote
is shorted or crowbarred to ground and Cout is greater than + Cout
Cin 1 R1 Load
50 mF, it becomes possible for device damage to occur. R2
Under these conditions, diode D1 is required to protect the
device. The second path connects between Cadj and Vout, and
it can withstand a peak surge current of about 150 mA.
Protection diode D2 is required if the output is shorted or
RW−
crowbarred to ground and Cadj is greater than 1.0 mF.
Figure 26. Load Sensing
D1
www.onsemi.com
10
NCP1117, NCP1117I, NCV1117
Figure 27. Constant Current Regulator Figure 28. Slow Turn−On Regulator
Input Output
3 NCP1117 2
XTA
10 + + 10
1 R1
mF mF
Input Output
3 NCP1117 2
XTA
10 + + 10 R2
1 120
mF mF
2N2222
Output Control 1.0 k 360
2N2222
On
Off 1.0 k
Output Voltage Control
Figure 29. Regulator with Shutdown Figure 30. Digitally Controlled Regulator
Input Output
3 NCP1117 2
XT50
10 + + 10
mF 1 mF
50 W
Input 3 NCP1117 2 Output
RCHG 5.3 V AC Line 5.0 V to
XT50 12 V
5.0 V Battery 10 + + 10
3 NCP1117 2 mF 1 mF
XT50
+ 10 + + 10
6.6 V mF 1 2.0 k mF
−
Figure 31. Battery Backed−Up Power Supply Figure 32. Adjusting Output of Fixed
Voltage Regulators
www.onsemi.com
11
NCP1117, NCP1117I, NCV1117
NCP1117ST33T3G 3.3
NCP1117ST50T3G 5.0
NCP1117ST12T3G 12
NCP1117DTAG Adjustable 75 Units / Rail
NCP1117DTARKG Adjustable 2500 / Tape & Reel
NCP1117DTAT5G Adjustable 2500 / Tape & Reel
NCP1117DT15G 1.5 75 Units / Rail
NCP1117DT15RKG 1.5 2500 / Tape & Reel
NCP1117DT18G 1.8 75 Units / Rail
NCP1117DT18RKG 1.8 2500 / Tape & Reel
NCP1117DT18T5G 1.8 2500 / Tape & Reel
NCP1117DT19RKG 1.9 2500 / Tape & Reel
NCP1117DT20G 2.0 75 Units / Rail
NCP1117DT20RKG 2.0 2500 / Tape & Reel
DPAK
NCP1117DT25G 2.5 75 Units / Rail
(Pb−Free)
NCP1117DT25RKG 2.5 2500 / Tape & Reel
NCP1117DT25T5G 2.5 2500 / Tape & Reel
NCP1117DT285G 2.85 75 Units / Rail
NCP1117DT285RKG 2.85 2500 / Tape & Reel
NCP1117DT33G 3.3 75 Units / Rail
NCP1117DT33RKG 3.3 2500 / Tape & Reel
NCP1117DT33T5G 3.3 2500 / Tape & Reel
NCP1117DT50G 5.0 75 Units / Rail
NCP1117DT50RKG 5.0 2500 / Tape & Reel
NCP1117DT12G 12 75 Units / Rail
NCP1117DT12RKG 12 2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
NCP1117IST50T3G 5.0
NCP1117IDTAT4G Adjustable
DPAK
NCP1117IDT33T4G 3.3 2500 / Tape & Reel
(Pb−Free)
NCP1117IDT50T4G 5.0
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
12
NCP1117, NCP1117I, NCV1117
NCV1117ST33T3G* 3.3
NCV1117ST50T3G* 5.0
NCV1117ST12T3G* 12
NCV1117DTARKG* Adjustable
NCV1117DT15RKG* 1.5
NCV1117DT18RKG* 1.8
NCV1117DT18T5G* 1.8
NCV1117DT20RKG* 2.0 DPAK
2500 / Tape & Reel
NCV1117DT25RKG* 2.5 (Pb−Free)
NCV1117DT33T4G* 3.3
NCV1117DT33T5G* 3.3
NCV1117DT50RKG* 5.0
NCV1117DT12RKG* 12
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and
PPAP Capable
www.onsemi.com
13
NCP1117, NCP1117I, NCV1117
SOT−223
ST SUFFIX
CASE 318H
1 2 3 1 2 3 1 2 3 1 2 3 1 2 3
Adjustable 1.5 V 1.8 V 1.9 V 2.0 V
1 2 3 1 2 3 1 2 3 1 2 3
2.5 V 3.3 V 5.0 V 12 V
DPAK
DT SUFFIX
CASE 369C
2 2 2 2 2 2
1 3 1 3 1 3 1 3 1 3 1 3
Adjustable 1.5 V 1.8 V 1.9 V 2.0 V 2.5 V
2 2 2 2
1 3 1 3 1 3 1 3
2.85 V 3.3 V 5.0 V 12 V
A = Assembly Location
L = Wafer Lot
Y = Year
WW, W = Work Week
G or G = Pb−Free Package
(Note: Microdot may be in either location)
www.onsemi.com
14
NCP1117, NCP1117I, NCV1117
SOT−223
ST SUFFIX
CASE 318H
1 2 3 1 2 3 1 2 3 1 2 3
Adjustable 1.8 V 3.3 V 5.0 V
DPAK
DT SUFFIX
CASE 369C
2 2 2
1 3 1 3 1 3
Adjustable 3.3 V 5.0 V
A = Assembly Location
L = Wafer Lot
Y = Year
WW, W = Work Week
G or G = Pb−Free Package
(Note: Microdot may be in either location)
www.onsemi.com
15
NCP1117, NCP1117I, NCV1117
SOT−223
ST SUFFIX
CASE 318H
1 2 3 1 2 3 1 2 3 1 2 3
Adjustable 1.5 V 1.8 V 2.0 V
1 2 3 1 2 3 1 2 3 1 2 3
DPAK
DT SUFFIX
CASE 369C
2 2 2 2
1 3 1 3 1 3 1 3
Adjustable 1.5 V 1.8 V 2.0 V
2 2 2 2
1 3 1 3 1 3 1 3
2.5 V 3.3 V 5.0 V 12 V
A = Assembly Location
L = Wafer Lot
Y = Year
WW, W = Work Week
G or G = Pb−Free Package
(Note: Microdot may be in either location)
www.onsemi.com
16
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOT−223
CASE 318H
ISSUE B
DATE 13 MAY 2020
SCALE 2:1
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
GENERIC
MARKING DIAGRAM*
XXXXXXG AYWW
ALYWW XXX
XXXXXG
IC Discrete
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
DOCUMENT NUMBER: 98AON10527D Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves
the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.
ADDITIONAL INFORMATION
TECHNICAL PUBLICATIONS: ONLINE SUPPORT: www.onsemi.com/support
Technical Library: www.onsemi.com/design/resources/technical−documentation For additional information, please contact your local Sales Representative at
onsemi Website: www.onsemi.com www.onsemi.com/support/sales