Professional Documents
Culture Documents
DN630 Series (ENG Ver) - 2014-1-28
DN630 Series (ENG Ver) - 2014-1-28
DACELL CO.,LTD
TEL:+82-43-260-2242
FAX:+82-43-260-2242
WEBSITE:http://www.dacell.com
EMAIL: info@dacell.com
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Contents
2
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Chapter 1. Preface
1. Introduction
This DN610 series Digital Weighing Indicator(DN610,DN630) model is din size powerful performance
for the industrial weighing system application.
RS-232 serial port can be expended up to 4pots, easy to connect with other devices and PC.
In case of DN630 model has 6pcs control relay output as a standard, easy to make weighing
automation system.
Please estimated this user manual and enjoy the performance of DN830 series digital weighing
Indicator.
2. Feature
2-1. Isolation from the external noise
2-2. Watch-dog function
2-3. Display resolution, up to 1/20,000
2-4. 2pcs Digital input terminal built in (Zero, Tare/Reset)
2-5. AC 85V~265V power supply.
2-6. Data back-up function
2-7. Full Automatic Calibration method
2-8. Simulating Calibration Method (without Span weight)
2-9. Option : RS-422
3. Caution
3-1. Weak for the drop damage or physical shock.
3-2. Do not install heavy electric noise place.
3-3. Do not install the heavy vibrating place.
3-4. Avoid from the humidity or rain damage.
3-5. Please Turn off the main power, when make connect with other devices.
4. Accessories
4-1. User Manual
5. Inquiries
If you have any kinds of inquiries for this model, please contact with your local agent or Head Office.
Head Office : DACELL co.,Ltd.
Website : http://www.dacell.com
Email : info@dacell.com
3
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Chapter 2. Specification
1. Analogue Input and A/D Conversion
Input Sensitivity 0.2㎶ / Digit
Load Cell Excitation DC 10V ( - 5V ~ + 5V )
Max. Signal Input Voltage Max.32mV
Temperature Coefficient [Zero] ±10PPM/℃ / [Span] ±10PPM/℃
Input Noise ±0.6㎶ P.P
Input Impedance Over 10㏁
A/D Conversion Method Sigma-Delta
A/D Resolution(Internal) 520,000 Count(19bit)
A/D Sampling Rate Max. 200times / Sec
Non-Linearity 0.01% FS
Display Resolution(External) 1/20,000
2. Digital Part
3. General Part
Power Supply SMPS Free Voltage (AC85~265V)
Operating Temperature Range -5℃ ~ 40℃
Operating Humidity Range Under 85% Rh (non-condensing)
External Dimension 96mm(W)x96mm(H)x135mm(L)
Net Weight(kg) About 600g
Gross Weight(kg) About 800g
4. Option
Option No.1 RS-422
Option No.2 RS-232 (Standard Installation)
Option No.5 4~20mA (Analogue Output)
Option No.6 0~10V (Analogue Output)
4
Digital Weighing Indicator – DN610/630 Model
Din Size Series
5
Digital Weighing Indicator – DN610/630 Model
Din Size Series
DN610 model
DN630 model
Set
SET UP Mode : (Press key with Power in)
Function Mode : Increase Function No.
Low set value or HI set value check or change.
6
Digital Weighing Indicator – DN610/630 Model
Din Size Series
8. Rear Panel
7
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Chapter 3. Installation
1. External Dimension
93mm
93mm 8
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Chapter 4. Calibration
1. SPAN Calibration
- Adjust weight balance between “Real weight” on the load cell(Weight Part) and “Displayed weight of
Indicator”. When you replace LOAD CELL or Indicator, you have to do Calibration process once again
SET-CAL
Pressing key during 7sec. then display will show .
SET-CAL
Or turn on the Power + with pressing display.
Remarks : Go to next step with save key / Back to previous step key
- Press key to save new set value and move to next step.
9
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Then, Press key to save new set value and move to next step.
Remarks
- The Max. capacity cannot be exceed Max. capacity of load cell.
- (Digit/Max. Capacity) value must be less than 1/20,000.
10
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Step 5. Input Prepared Test weight value and load on the Scale.
SPAn
- Then display will show and then, input prepared test weight value whenever
pressing key, value will be increased, Whenever pressing key, you can move to the
left digit
C_UP_
- Then display will show and then, load prepared test weight unit on the scale.
- After a few seconds (to remove the vibration effect), press key.
Then, indicator will calculate Span value and move the next step.
- Calculated Span value will be displayed and automatically reset and move the normal weight
indicating mode.
11
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Chapter 5. Set-Up
1. Set-Up
Set-up means set the F-function and make DN610 series weighing controller will perform more
accuracy. (Considering external / internal environmental condition)
SET-CAL
Pressing key during 7sec. then display will show .
At the function No. display, input new set value with key and .
If you don’t press key, new set value will not be saved.
12
Digital Weighing Indicator – DN610/630 Model
Din Size Series
After save new set value with pressing key, then press key to Function mode.
13
Digital Weighing Indicator – DN610/630 Model
Din Size Series
1. F-Function List
14
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Other setting
F80 Empty Range setting XXXXXX
15
Digital Weighing Indicator – DN610/630 Model
Din Size Series
2. F-function Details
F00
key : Move to Set-up mode key : Move to Calibration mode
Decimal Point Setting
0 No Decimal Point
Weight
Zero breaks
Display Current weight
0.075kg
(1.5ⅹdigit)
Display Zero
time
about 5msec.
16
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Within the “Auto Zero” range, weighing part is steady, indicator will
00 display current weight as “Zero”
F05 00 + If the weighing part is not “Steady”, indicator will display current
99 weight.
(Auto Zero Range : ± Set value + weight unit)
※ Using this function, you can get the Zero value without pressing “Zero” key, when there is
remained material in the hopper within Auto Zero Range.
-0.30kg
Motion Band Range F03-01
17
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Set Value
18
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Set Value
Ï 0 Fixed Code
19
Digital Weighing Indicator – DN610/630 Model
Din Size Series
4 Comparison 2. (Checker 2)
5 Comparison 3.(Checker 3)
Checker Mode 1. : Will start checking the weight, after “Judge” input.
Checker Mode 2. : Will start checking the weight, after “Hold” input.
Checker Mode 3. : Check the weight and relay output, after “Steady Lamp”.
20
Digital Weighing Indicator – DN610/630 Model
Din Size Series
◆ Weighing Mode 1. Limit Mode 1. (F21-01 setting) - Relay “ON” when weight reaches to set
value
Weight
SP1
Near Zero
TARE(IN)
Output 1
SP1
Output 2
SP2
t1 t2 Output 3
FINISH
t5 Output 4
LOW NG
t5 Output 5
HI NG
Output 6
EMPTY
21
Digital Weighing Indicator – DN610/630 Model
Din Size Series
SP1
Near Zero
TARE(IN)
RUN(IN)
SP1 Output 1
SP2 Output 2
FINISH t1 t2 Output 3
LOW NG t5 Output 4
HIGH NG t5 Output 5
EMPTY Output 6
22
Digital Weighing Indicator – DN610/630 Model
Din Size Series
SP2
OK
SP1 LOW
EMPTY
JUDGE Input
t3 t4
Output 1
SP1
t3 t4 Output 2
SP2
t3 t4Output 3
OK
t5
Output 4
LOW N.G
t5 Output 5
Output 6
HI N.G
Empty
SP1 Less than LOW set value, “ON” LOW N.G Less than LOW set value, “ON”
SP2 More than HIGH set value, “ON” HI N.G More than HIGH set value, “ON”
23
Digital Weighing Indicator – DN610/630 Model
Din Size Series
SP2
OK
SP1 LOW
EMPTY
HOLD Input
t3 t4
Output 1
SP1
t3 t4 Output 2
SP2
t3 t4Output 3
OK
t5
Output 4
LOW N.G
t5 Output 5
Output 6
HI N.G
Empty
SP1 Less than LOW set value, “ON” LOW N.G Less than LOW set value, “ON”
SP2 More than HIGH set value, “ON” HI N.G More than HIGH set value, “ON”
24
Digital Weighing Indicator – DN610/630 Model
Din Size Series
SP2
OK
SP1 LOW
EMPTY
t4
Output 1
SP1
t4
Output 2
SP2
t4
Output 3
OK
t5
Output 4
LOW N.G
t5 Output 5
HI N.G
Empty Output 6
SP1 Less than LOW set value, “ON” LOW N.G Less than LOW set value, “ON”
SP2 More than HIGH set value, “ON” HI N.G More than HIGH set value, “ON”
25
Digital Weighing Indicator – DN610/630 Model
Din Size Series
F22 10 +
FINISH Relay
Com-Out5
99
“00” setting : At Steady point, FINISH relay output
“20” setting : After 2.0sec from Steady point, FINISH relay output
“99” setting : After 9.9sec from Steady point, FINISH relay output
FINISH Relay “ON” time(t2) setting (Under F21-01, 02 setting)
You can set duration time for FINISH relay.
01 Steady point
F23 10 +
t2
FINISH Relay
99 Com-Out5
“01” setting : FINISH relay will be “ON during 0.1sec.
“20” setting : FINISH relay will be “ON” during 2.0sec.
“STEADY” Judging delay time(t3) setting (Only for F21-03, 04 Check mode)
After current weight is reached to each set point, you can set some
delay time of “STEADY”.
Steady point
01
F24 10 + t3
Com-Out5
99
“00” setting : At Steady point, FINISH relay output
“20” setting : During 2.0sec, hold “Steady” relay
“99” setting : During 9.9sec, hold “Steady” relay
“STEADY” Judging “ON” time(t4) setting (Only for F21-03, 04 Check mode)
After current weight is reached to each set point, you can set some
delay time of “STEADY”.
Steady point
00
F25 10 +
t4
99 Com-Out5
26
Digital Weighing Indicator – DN610/630 Model
Din Size Series
2 Even Parity
F32 1 Finish Mode : When Finish Relay output, only 1 time transferred.
27
Digital Weighing Indicator – DN610/630 Model
Din Size Series
F40 1 g
2 t
Continuous Print
Ï 0
Serial No. and Weight will be printed continuously.
F42
Single Print
1
Date, Time, S/N, ID No. Weighing Data will be print
1
F44 3 + Whenever set value increased, 1line will be added.
9
1
F45 3 + Whenever set value increased, 1line will be added.
9
28
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Ï 0 KOREAN
F47
1 ENGLISH
00 00 : No Delay time
F48 00 +
99 99 : 9.9sec later, print output
Other Setting
F90 Check Current DATE data or you can Change to new date
F91 Check Current TIME data or you can Change to new TIME
29
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Chapter 7. Interface
1. Rs-232C (Standard Installed)
RS-232C Serial Interface is sensitive/weak for electric Noise.
So, please isolate with AC power cable and use shield cable to reduce the electric noise effect.
1-1. Connection
GND2---------------------- Pin5
, , K g CR LF
▶ Header 1
- OL : OVER LOAD or UNDER LOAD
- ST : Weight Stable
- US : Weight Unstable
▶ Header 2
- NT : Net Weight (Without TARE Weight)
- GS : Gross Weight (With TARE Weight)
▶ DATA(8) Symbol(1) , Decimal Point(1) , Weight (6) = total 8BYTE, like +000.190
- 2B(H): "+"PLUS
- 2D(H): "-"MINUS
- 2O(H): " "SPACE
- 2E(H): "."Decimal point
▶ UNIT
- Kg , g
, , , K g CR LF
▶ Header 1
- OL : OVER LOAD or UNDER LOAD
- ST : Weight Stable
- US : Weight Unstable
▶ Header 2
- NT : Net Weight (Without TARE Weight)
- GS : Gross Weight (With TARE Weight)
▶ DATA(8) Symbol(1) , Decimal Point(1) , Weight (6) = total 8BYTE, like +000.190
- 2B(H): "+"PLUS
- 2D(H): "-"MINUS
- 2O(H): " "SPACE
- 2E(H): "."Decimal point
▶ UNIT
- Kg , g
31
Digital Weighing Indicator – DN610/630 Model
Din Size Series
2-1. Connection
2-3. Data Protocol (Data Format 1. – Total 18byte) - As same as “Rs-232c Serial Interface
, , K g CR LF
2-4. Data Protocol (Format 2 – Total 22byte) - As same as “Rs-232c Serial Interface
, , , K g CR LF
32
Digital Weighing Indicator – DN610/630 Model
Din Size Series
▶ COMMAND MODE
PCIndicator (ASCII)
Format (HEX)
Time Data
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Serial No.
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Code No.
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Part No.
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
TARE weight
Response (ASCII) value
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Current
Response (ASCII) Weight value
from
Indicator
(HEX)
33
Digital Weighing Indicator – DN610/630 Model
Din Size Series
PCIndicator (ASCII)
Format (HEX)
Response (ASCII)
from (HEX)
Sub-Total
Indicator Data
PCIndicator (ASCII)
Format (HEX)
Response (ASCII)
from
Grand-Total
Indicator
Data
(HEX )
PCIndicator (ASCII)
Format (HEX)
Weighing
Response (ASCII) Condition
from (HEX)
Indicator
PCIndicato (ASCII)
r Format (HEX)
Response
from
Indicator
Memorized
Data
(HEX)
PCIndicator (ASCII)
Format (HEX) Low (SP1)
Response (ASCII) DATA
from
34
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Indicator (HEX)
PCIndicator (ASCII)
Format (HEX)
High (SP2)
Response (ASCII) DATA
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Free Fall
Response (ASCII) DATA
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX )
Under
Response (ASCII) Weight DATA
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Over Weight
Response (ASCII) DATA
from (HEX)
Indicator
TxD
PCIndicator (ASCII)
Format (HEX)
TARE input
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
TARE RESET
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
ZERO input
Response (ASCII)
from (HEX)
Indicator
35
Digital Weighing Indicator – DN610/630 Model
Din Size Series
PCIndicator (ASCII)
Format (HEX)
Print input
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format ( HEX)
Sub-Total Print
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Grand-Total
Response (ASCII) Print
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
PCIndicator (ASCII)
Format (HEX)
PCIndicator (ASCII)
Format (HEX)
36
Digital Weighing Indicator – DN610/630 Model
Din Size Series
PCIndicator (ASCII)
Format (HEX)
PCIndicator (ASCII)
Format (HEX)
Hold input
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Hold RESET
Response (ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Sub-Total Data
Response (ASCII) Clear
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Grand-Total
Response (ASCII) Data Clear
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX) Start(Run) Input
Response (ASCII)
(F21 – 02)
from (PACK MODE)
(HEX)
Indicator
PCIndicator (ASCII)
Format (HEX) STOP Input
Response (ASCII)
(F21 – 02)
from (PACK MODE)
(HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Low (SP1) set
Remark STX(1) ID(2) Command(4) Low<SP1>(6) ETX(1) value change
Response (ASCII)
37
Digital Weighing Indicator – DN610/630 Model
Din Size Series
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Remark STX(1) ID(2) Command(4) High<SP2>(6) ETX(1) High (SP2) set
Response value change
(ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Remark STX(1) ID(2) Command(4) Free Fall(6) ETX(1) Free Fall set
Response value change
(ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Remark STX(1) ID(2) Command(4) Under(4) ETX(1) Under Limit set
Response value change
(ASCII)
from (HEX)
Indicator
PCIndicator (ASCII)
Format (HEX)
Remark STX(1) ID(2) Command(4) Over(4) ETX(1) Over Limit set
Response (ASCII)
value change
from (HEX)
Indicator
38
Digital Weighing Indicator – DN610/630 Model
Din Size Series
Display will show “TEST”, then select each test mode, with pressing key.
Press key for the certain TEST mode, and enter to that TEST mode.
- Calibration Mode
TEST 3
☞ Back to the TEST mode, press key.
TEST 4
- Display Test Mode. key to back to the other TEST Mode.
TEST 5
- Relay Test Mode. key to back to the other TEST Mode.
TEST 6
- Input Test Mode. key to back to the other TEST Mode.
TEST 7
- Analogue Value amplification Test. key to back to the other TEST Mode.
※If you installed Analogue Option card, you can test Analogue output test with “TEST 2”
mode. (Please check detailed information)
39
Digital Weighing Indicator – DN610/630 Model
Din Size Series
1).Input Resistance
1). Load cell broken of “EX+” and “EX-
1). Measure
2). Load cell “ is about
input/output resistance
isolation 350& ~450& .
of Load cell.
resistance error
3). Weighing part 2). Output
Weight Value is 2). Measure Load cell
touches other Resistance of “EX-
unstable isolation resistance
devices or some “ and “EX+” is
weight is on the about 350& .
3) Check attach point
weighing part
with other devices.
4). Summing Board 3). Isolate
Error Resistance is more
than 100&
“OL” or “UL” display 1). Load cell broken 1). Load cell Check
or Indicator 2). Load cell connection
connection Error Check
2). Loading over than 3). Remove over
Max. Capacity loaded weight
40
Digital Weighing Indicator – DN610/630 Model
Din Size Series
1. Amp. Gain is too big Check standard weight’s weight with set value.
2. Sig+ and Sig- wire If there is difference between set value and real
Err 06
connection error weight, please re-input the value
3. Test weight is not loaded (set value is too small)
1. Amp. Gain is too small Check standard weight’s weight with set value.
2. Sig+ and Sig- wire If there is difference between set value and real
Err 07
connection error weight, please re-input the value
3. Test weight is not loaded (set value is too big)
41