This document provides inspection instructions for repaired products at Bien-Air in Switzerland. It lists medical and dental tool designations and references before and after repair. It outlines inspection criteria like lubricating instruments, running handpieces to check for excessive current or noise, testing water tightness and light output. Inspectors check that repaired tools meet standards for grip strength, vibration, heat, spray quality and functioning properly.
This document provides inspection instructions for repaired products at Bien-Air in Switzerland. It lists medical and dental tool designations and references before and after repair. It outlines inspection criteria like lubricating instruments, running handpieces to check for excessive current or noise, testing water tightness and light output. Inspectors check that repaired tools meet standards for grip strength, vibration, heat, spray quality and functioning properly.
This document provides inspection instructions for repaired products at Bien-Air in Switzerland. It lists medical and dental tool designations and references before and after repair. It outlines inspection criteria like lubricating instruments, running handpieces to check for excessive current or noise, testing water tightness and light output. Inspectors check that repaired tools meet standards for grip strength, vibration, heat, spray quality and functioning properly.
BIEN-AIR REPAIRED PRODUCT INSPECTION INSTRUCTION IC 751-015 Rév.
0005 SWITZERLAND
INSTRUCTION N o : 12 Modified 18.12.09
CONCERNED ARTICLE CONCERNED ARTICLE
DESIGNATION OLD REFERENCE NEW REFERENCE DESIGNATION OLD REFERENCE NEW REFERENCE
PM 830 131.11.01A -- CA 10:1 41 133.38.01C 1600038C
C PML 1:1 21 131.12.01 A 1600156 A CA 10:1 133.38.03 1600385C PM 1122 131.16.01A -- CA 10:1 31 133.39.01 1600425 A A A A PM 1132 / 1123 131.22.01 / 131.22.02 1600054 / 1600052 CA 100:122 133.40.01 1600201 A 133.41.01 1600290 PM1132 Sudo 131.22.03 -- CAP 15:1 21 A A 133.42.01 1600319 PM 1132 131.22.10 1600404 CAP 15:141 PM 1:1 131.22.12A 1600383A CAE 10:1 41 133.46.01C 1600050C PM 1124 -- 1600612 CAE 10:1 31 133.47.01 1600051 A A A A PM 860 / 861 131.24.01 / 131.24.03 -- / -- PMRM 111 / 1122 131.18.02 / 131.18.04 -- / 1600206A PMP 10:1 21 131.27.01 A 1600289 A PMRM 1122 INTRA-NASAL 131.18.06A 1600329A CA 111 133.03.01 -- PMRM 1122/95 INTRA-NASAL 131.18.07 A 1600340A CA 1:1 21 133.08.01 -- PMRM 1122/125 INTRA-NASAL 131.18.08 A 1600341A CA 1141 133.24.01B -- PMAM 111 / 1122 133.06.02A / 133.06.03 -- / 1600207 CA 7141 133.25.01 B -- PMAM 1122 INTRA-NASAL 133.06.04A 1600328A CA 1132 133.27.01 1600055 PMAM 1122/95 INTRA-NASAL 133.06.05A 1600336A CA 1122 133.08.05 1600200 PMAM 1122/125 INTRA-NASAL 133.06.06 A 1600337A CA 30:122 133.52.01 1600284 PMAM 1221 133.15.01A 1600295A A CA 7132 133.28.01 1600056 PMAM 1221/95 133.15.02 1600338A A CA 1142 133.32.01C 1600061C PMAM 1221/125 133.15.03 1600339A CA 1:1 133.32.06C 1600384C PMAM 10121 133.16.01A 1600202A CA 1:1 33 133.34.01 1600424 PM FISCH PM MICRO 1600470A C CA 1:1 sp. ext. -- 1600603 CA 20:1 L 1600598 PM HP 1:2 -- 1600436 CA 20:1 1600632
Inspection UNIT, TOLERANCES AND EVALUATION
INSPECTION CRITERIA instrument Ok CRITERIA LUBRICATE THE INSTRUMENT BEFORE INSPECTION 1600064 Lubrifluid PROGRESSIVELY (STEP BY STEP) RUN THE 107.70.01 / Inspection rack HANDPIECE/CONTRA-ANGLE 107.70.02 RUN IN THE HANDPIECE/CONTRA-ANGLE 3 min at 30'000 rpm and 2 min at 40'000 rpm MEASURING OF THE CURRENT ON THE INSPECTION 107.70.01 / Maxi 0.40 A RACK 107.70.02 AXIAL BUT GRIPPING ON HANDPIECE 107.61.02 Minimum holding red line 40 N A (tap the inspection gauge 2-3 times before the test) Holding 1st green line 45 N A AXIAL BUR GRIPPING ON CONTRA-ANCLE Left to the operator's discretion VIBRATION, NOISE Left to the operator's discretion OVERHEATING Left to the operator's discretion QUALITY OF THE SPRAY (air-water 2 bar) Left to the operator's discretion WATERTIGHTNESS OF THE HANDPIECE/CONTRA- No leak when the water/air outlet is blocked ANGLE LUMINOSITY A 3.5 VDC +/- 0.1 V* 3600001-001 B 1 klux minimum LUMINOSITY A 3.5 VDC +/- 0.1 V* 3600001-001 2 klux minimumC LUMINOSITY A 3.5 VDC +/1 0.1 V* Visual, white light CHECK COUPLING OF HANDPIECE OR CONTRA- Left to the operator's discretion ANGLE ON MOTOR DEVICE FUNCTIONING OF THE DRIVE Left to the operator's discretion OVERALL OUTSIDE ASPECT Left to the operator's discretion