Professional Documents
Culture Documents
V2460 Manual de Instrução
V2460 Manual de Instrução
V2460
video controller
user manual
Machine Translated by Google
update record
ÿSupport 3D function.
www.novastar-led.cn i
Machine Translated by Google
Table of contents
www.novastar-led.cn ii
Machine Translated by Google
www.novastar-led.cn iii
Machine Translated by Google
overview
product introduction
V2460 is a 2-in-1 video controller that integrates video processing and video control functions with 24 network ports output. A single device can carry a maximum
of 15.6 million pixels, a maximum width of 16384 pixels, and a maximum of 8192 pixels, which can meet the on-site ultra-wide and ultra-high display control.
The V2460 has powerful video signal receiving and processing capabilities, supports 10bit video processing, supports a maximum of 4K×2K@60Hz video
input, and supports a maximum of 6+1 video signal inputs, supports 6 independent windows, output image scaling, point-by-point Brightness and chroma
The V2460 adopts an industrial-grade casing. With its powerful video processing and sending capabilities, it can adapt to complex operating environments and is widely used in
various large-scale fixed installations such as governments, enterprises and institutions, and military command centers.
Product Features
ÿSupport 3D function. ÿSupport to display 1 channel OSD screen at the same time
Cooperate with 3D transmitter EMT200 and supporting 3D ÿA maximum of 6 OSDs can be imported and stored
www.novastar-led.cn 1
Machine Translated by Google
V2460 Video Controller User Manual 1 Overview
ÿ Equipped with SuperView III image quality processing technology, ÿ Synchronous output
ÿSupport arbitrary interception of input source ÿ Point-by-point brightness and chromaticity correction
ÿSupport EDID management Cooperate with NovaLCT and calibration platform to calibrate the
Support output quality management, including brightness, saturation, the same time, it supports hardware display function.
to load
ÿFlexible routing
operate
the network port is used to the fullest.
ÿHot Backup
www.novastar-led.cn 2
Machine Translated by Google
Exterior
front panel
button illustrate
ÿWhen the window is opened, short press the window button to enter the corresponding window property menu
ÿWhen the window is open, press and hold the window button to close the window
ÿWhen the button light is flashing, it means that the window is being edited
WIN-3 windows, WIN-4 windows, WIN-5 windows, WIN-6 windows do not support switching source to HDMI 2.0
or DP 1.2.
ÿ SCALE key: Shortcut key for "full screen auto zoom", the window with the lowest priority and opened will
TFT screen Used to display the current status of the device, as well as the setting menu
www.novastar-led.cn 3
Machine Translated by Google
input source Input source switching key and input source signal status
On the main menu interface, when the WIN-1 window is open, it supports short pressing the input source button to quickly switch the source.
Press and hold the knob and the return button at the same time for more than 3 seconds to lock or unlock the front panel buttons.
rear panel
*The product pictures in this article are for reference only, please refer to the actual product purchased.
input interface
www.novastar-led.cn 4
Machine Translated by Google
audio port
Output Interface
www.novastar-led.cn 5
Machine Translated by Google
When the number of input source bits is 8bit and the output frame rate is 60Hz, 650,000 images
raw score
Network port 1 and network port 2 support audio output. When analyzing audio through a multi-function card, you need
control interface
ÿThe indicator light in the upper left corner of the network port is the current connection status indicator of the network port
ÿThe indicator light in the upper right corner of the network port is the communication status indicator of the current network port
www.novastar-led.cn 6
Machine Translated by Google
Application Scenario
www.novastar-led.cn 7
Machine Translated by Google
Main interface
Local IP
ÿPress and hold the knob and ESC key at the same time to lock/unlock the keys
ÿWhen the LCD on the front panel is locked, all key operations are disabled.
B: Input Source Status Module Window 1 is open and using the HDMI source as the input source
C: configured screen size Displays the resolution and refresh rate of the configured display
www.novastar-led.cn 8
Machine Translated by Google
ÿThe network port has been connected and is an output backup port
ÿThe lower right corner flashes when the backup takes effect
F: Function status module synchronization setting The synchronization function is enabled and the synchronization is successful
3D settings 3D function on
www.novastar-led.cn 9
Machine Translated by Google
menu operation
Knob:
ÿ On the main interface, press the knob to enter the menu operation interface. ÿ In
the menu operation interface, rotate the knob to select the menu, press the knob to select the current menu or enter the submenu option. ÿ Select the menu with
parameters, turn the knob to adjust the parameters, press the knob again to confirm after the adjustment is completed.
ESC: return key, short press to exit the current menu or operation.
Screen brightness
According to the current ambient brightness and the comfort of human eyes, adjust the brightness value of the LED display and solidify it to the receiving card in real time.
Step 2 Select "Screen Brightness", press the knob to confirm and adjust the brightness value.
Step 3 Turn the knob to adjust the brightness value of the display, the display will display the adjustment effect in real time, press the knob to confirm the application.
input settings
V2460 supports HDMI 2.0, DP 1.2, HDMI 1.3 and 3G-SDI, among which 3G-SDI interface is an optional interface.
www.novastar-led.cn 10
Machine Translated by Google
Turn the knob to the target input source, press the knob to enter the input source resolution setting interface.
ÿPreset resolution
ÿCustom resolution
default resolution
Set the resolution of the input source by selecting the preset resolution and preset refresh rate. After the parameter setting is completed, turn the knob to "Apply",
www.novastar-led.cn 11
Machine Translated by Google
1024×768@ÿ48/50/60/75/85ÿHz ÿ ÿ ÿ
1280×720@ÿ24/25/30/48/50/60ÿHz ÿ ÿ ÿ
1280×1024@ÿ48/50/60/75/85ÿHz ÿ ÿ ÿ
1364×768@ÿ50/60ÿHz ÿ
1366×768@ÿ50/60ÿHz ÿ ÿ
1440×900@ÿ60/75/85ÿHz ÿ ÿ ÿ
1600×1200@ÿ48/50/60ÿHz ÿ ÿ ÿ
1680×1050@60Hz ÿ ÿ ÿ
1920×1080@ÿ24/25/30/48/50/60ÿHz ÿ ÿ ÿ
1920×1200@ÿ50/60ÿHz ÿ ÿ ÿ
2048×1080@ÿ30/48/50/60ÿHz ÿ ÿ ÿ
2048×1152@ÿ30/60ÿHz ÿ ÿ ÿ
3840×1080@30Hz ÿ ÿ
2560×1080@ÿ50/60ÿHz ÿ ÿ
2560×1600@ÿ50/60ÿHz ÿ ÿ
3840×1080@ÿ50/60ÿHz ÿ ÿ
3840×2160@ÿ24/25/30ÿHz ÿ ÿ
2560×1600@120Hz ÿ ÿ
3840×2160@ÿ50/60ÿHz ÿ ÿ
3840×1080@120Hz ÿ ÿ
4096×2160@ÿ30/60ÿHz ÿ ÿ
7680×1080@ÿ30/60ÿHz ÿ ÿ
8192×1080@ÿ30/60ÿHz ÿ ÿ
www.novastar-led.cn 12
Machine Translated by Google
custom resolution
By setting the custom width, custom height, custom refresh rate, and input source resolution, after the parameter setting is completed, turn the knob to "Apply", and
limited to complete
The V2460 supports converting the RGB limited color space of the input source into the full RGB color range, so that the device can perform video processing more
accurately.
ÿOff : Do not perform RGB limited to full color space conversion for the current input source.
ÿEnable : Automatically perform RGB limited to full color space conversion for the current input source. It is recommended to turn on this when the color space is limited
Function.
window properties
V2460 can add up to 2 4K×2K and 4 2K×1K windows in any layout, and supports setting window properties. The window property menu is shown in Table 5-2 .
www.novastar-led.cn 13
Machine Translated by Google
menu illustrate
input source Used to select the input source for window display
zoom mode
Optional "full screen", "peer-to-peer" and "custom"
horizontal width
The horizontal width of the window, ranging from 64 to 32768
vertical height
The vertical height of the window, ranging from 64 to 32768
horizontal start
The starting coordinates of the horizontal direction of the window, the range value is -32768ÿ32768
vertical start
The vertical starting coordinate of the window, the range is -32768ÿ32768
priority
Hierarchical relationship displayed in the window, optional "1", "2", "3", "4", "5", "6"
input interception
It is used to display the partial screen captured by the input source, which covers the entire window
ÿStatus : the status of the input interception function of the selected window, the user can select "on" or "off"
ÿHorizontal start: the starting coordinate of the interception area relative to the horizontal direction of the current input source, the default value is 0
ÿVertical start: the starting coordinate of the interception area relative to the vertical direction of the current input source, the default value is 0
add window
key operation
Step 1 Short press the window button in the "WINDOWS" area of the front panel, the window button light will flash, the LCD panel will enter the window properties interface, and
And the "Status" of the window is automatically set to "Open", that is, the window is added.
Step 2 Short press the input source in the "Source" area to select the input source for the window.
www.novastar-led.cn 14
Machine Translated by Google
menu operation
Step 1 On the main interface, press the knob to enter the main menu interface.
Step 2 Turn the knob to select "Window Properties", and press the knob to enter the "Window Properties" interface.
Step 3 Turn the knob to select "Window n Properties", and press the knob to enter the corresponding window property interface.
Step 4 Rotate the knob to select "Status", press the knob and rotate the knob to select "On", press the knob again to set the window "Status" to
"turn on".
Step 5 Rotate the knob to select "Input Source" to set the window input source.
Step 6 Turn the knob to set other properties of the window. The description of the window properties is shown in Table 5-1 and Figure 5-6 .
Step 7 Turn the knob to select "Priority" to set the priority of the window. The priority is represented by numbers. The larger the number, the higher the priority.
Displayed earlier.
www.novastar-led.cn 15
Machine Translated by Google
key operation
Step 1 Select the window to be switched in the "WINDOWS" area of the front panel, and short press the button corresponding to the window.
After short pressing the window button, the window button light will flash, and the LCD interface will enter the property interface corresponding to the window.
Step 2 Short press the input source in the "SOURCE" area to switch the input source for the window.
ÿ On the main menu interface, when the WIN-1 window is open, short press the input source button to quickly switch the source.
ÿ Press the "SCALE" key to quickly and automatically display the window with the lowest priority in full screen.
menu operation
Step 1 On the main interface, press the knob to enter the main menu interface.
Step 2 Select "Window Properties > Window n Properties > Input Source", press the knob to enable the input source switching function.
input interception
Input interception is to select a part of the input source area of the current window, and enlarge the selected area to display in the entire window.
Step 1 On the main interface, press the knob to enter the main menu interface.
Step 2 Select "Window Properties > Window n Properties > Input Intercept", and press the knob to enter the input intercept interface.
Step 3 Rotate the knob to select "State", and set the input intercept state to "On".
www.novastar-led.cn 16
Machine Translated by Google
Step 4 Turn the knob to set the "Horizontal Width", "Vertical Height", "Horizontal Start" and "Vertical Start" of the input interception, and the input interception parameters say
background settings
V2460 supports background setting, turn the knob on the window property interface to select “background setting” to enter the background setting interface.
Step 2 Set the "Background Type". The background type can be set to "Solid Color" or "Picture".
www.novastar-led.cn 17
Machine Translated by Google
ÿWhen the background is selected as "Pure Color", set the component values of "Red", "Green" and "Blue" respectively in the "Pure Color Setting" interface to set the background
color.
ÿWhen the background is selected as "picture", select the background picture imported from the host computer as the background in the "picture selection" interface.
Step 3 Turn the knob to select "Apply", and press the knob to make the set background take effect.
ÿ V2460 supports importing a maximum of 4 BKG pictures, and the maximum width of the picture is 8192 or the maximum height is 8192. ÿ
Before using BKG, you need to use the upper computer V-Can to import BKG pictures. ÿ BKG is
OSD configuration
V2460 supports adding 6 OSDs, one OSD can be used at a time, and the OSD is displayed on top.
Before adding OSD to V2460, you need to import OSD pictures or edit OSD text through V-Can.
Step 2 Turn the knob and turn "Window Properties > OSD Configuration" to enter the OSD configuration interface.
Step 3 Refer to Table 5-3 to set the OSD properties of each window.
www.novastar-led.cn 18
Machine Translated by Google
menu illustrate
OSD status OSD function state, optional "on" or "off", the default is "off".
"OSD6".
Before using the OSD, you need to use the upper computer V-Can to import the OSD.
Horizontal start position The start coordinate of OSD relative to the horizontal direction of the screen, the default is 0, and the range value is 0~16384.
Vertical start position The start coordinate of OSD relative to the vertical direction of the screen, the default is 0, and the range value is 0ÿ8192.
ÿ The LCD interface does not support the adjustment of the size of the OSD. If you need to adjust the size of the OSD, please perform corresponding adjustments on the V-Can
close operation.
ÿ When configuring OSD text, it supports the configuration of OSD text style and scrolling mode.
picture control
On the "Main Menu" interface, turn the knob to select "Screen Control" to enter the screen control interface.
www.novastar-led.cn 19
Machine Translated by Google
ÿNormal display: Play the content of the current input source normally.
ÿTest screen: Enter the test screen to test the display effect of the display screen and the working status of the light points. The test screen contains pure
ÿImage quality adjustment: It is used to adjust the image quality adjustment parameters of the display screen output screen, and the display screen will display the adjustment effect in real time.
parameter describe
scene setting
A scene is a collection of parameters used to save all information of a window and its associated information. The V2460 supports the configuration of 10 user scenarios,
After the scene data is saved, the user can call the saved user scene directly through the scene name, and can modify the scene
On the main interface, press the knob to enter the "Main Menu" interface, turn the knob to select "Scene Setting" and press the knob to enter the scene setting interface.
noodle.
save scene
After the window configuration is completed, the configured window information can be saved to the scene.
www.novastar-led.cn 20
Machine Translated by Google
Step 1 On the "Scene Setting" interface, turn the knob to select a scene name.
Step 3 Select "Save" and press the knob to save the window information in the current screen to the scene.
After the scene is saved, the status after the scene will change to "saved".
load scene
Scene loading is to directly load the window information in the saved scene to the screen.
Step 1 On the "Scene Settings" interface, turn the knob to select the name of the scene whose scene status is "Saved".
Step 3 Select "Load" and press the knob to load the window information saved in the current scene to the screen.
After the scene is loaded, the status behind the scene will change to "in use".
delete scene
Deleting a scene refers to clearing the data information saved in the scene. The scene name will not be cleared. After the scene data is cleared, the scene status will
become "blank".
Step 1 On the "Scene Settings" interface, turn the knob to select the name of the scene whose scene status is "Saved".
Step 3 Select "Delete", press the knob to pop up the delete scene confirmation interface.
Step 4 Turn the knob to select "Yes", and press the knob to confirm deletion.
copy scene
To copy a scene is to copy the currently saved scene data to another scene.
Step 1 On the "Scene Settings" interface, turn the knob to select the name of the scene whose scene status is "Saved".
Step 3 Select "Copy to", and press the knob to enter the "Scene Setting" interface.
Step 4 Rotate the knob to select a scene name, press the knob to confirm.
After the scene is copied, the status of the copied scene will become "saved".
www.novastar-led.cn 21
Machine Translated by Google
advanced settings
backup settings
The V2460 supports two types of backups: device hot backup and network port backup.
Device hot backup is to set the whole machine backup relationship between two devices. You can set one of the devices to be the main control device or the backup device. When there is a
problem with the main control device or the network cable of the main control device, the backup device will take over. The responsibility of the main control device, continue to work, no black
screen appears.
Step 1 On the main menu interface, select "Settings > Device Hot Backup" to enable hot backup settings.
www.novastar-led.cn 22
Machine Translated by Google
ÿ When the active and standby devices are loaded, the load capacity of the same network port of the main control device and the backup device must be the same, and the wiring of the cabinet is just right.
on the contrary.
ÿ The settings of the window properties in the master device and the backup device must be consistent. When the input sources of all windows of the master device are different
Network port backup is to set the backup relationship of two output network ports of V2460. When the main network port fails or the connection of the main network port fails, the
backup network port takes over from the main network port for data transmission to avoid black screen. When setting network port backup, you need to use the
www.novastar-led.cn 23
Machine Translated by Google
Step 1 Start NovaLCT and select "Login > Synchronize Advanced Login" to log in to NovaLCT.
www.novastar-led.cn 24
Machine Translated by Google
Step 4 Select Sending Card, and click Add in the lower right corner of the Redundancy area.
Step 5 Set both the master sending card serial number and the backup sending card serial number to 1.
Step 6 Set the serial number of the main output network port after the "main control output serial number", and set the backup network of the main output network port in the "backup output serial number".
serial number.
Step 7 Click Add, and the system will automatically list the main output network port and the backup output network port list.
www.novastar-led.cn 25
Machine Translated by Google
Step 8 Repeat steps 6 and 7 to complete the active and standby settings of other network ports.
Step 9 Click Send to send the redundant information to the sending card and receiving card.
Step 10 Click Save to save the backup parameters to the sending card and receiving card.
Sync settings
Set the synchronization source when the devices are cascaded or the active and standby devices are loaded, so as to achieve the effect of synchronizing the output screen.
Step 1 On the main menu interface, select "Advanced Settings > Synchronization Settings" to enter the synchronization settings interface.
Step 2 Rotate to select "Status", press the knob and rotate the knob to select "On", press the knob to set the synchronization status to "On".
Step 3 Rotate the knob to select "Sync source selection", press the knob and rotate the knob to select the input source as the sync source, press the knob to set the sync source
step source.
www.novastar-led.cn 26
Machine Translated by Google
If two or more V2460s jointly load one screen, the synchronization source needs to be set to the same video source.
audio settings
Set the output audio, output volume and audio of the input source in the audio settings.
When connecting via a multi-function card, the network port 1 or network port 2 is connected to the multi-function card, and the multi-function card is connected to an external speaker.
www.novastar-led.cn 27
Machine Translated by Google
ÿ AUDIO output interface connection, directly connected to external speakers through the AUDIO output interface.
On the main menu interface, select "Advanced Settings > Audio Settings", and press the knob to enter the audio settings interface.
Step 2 Press the knob to enable "Audio Output Selection", and turn the knob to select the current audio output window.
www.novastar-led.cn 28
Machine Translated by Google
ÿWindow 1/Window 2/Window 3/Window 4/Window 5/Window 6: External speakers play Window 1, Window 2, Window 3, Window
ÿ Audio In: External speakers play audio from the audio input interface, such as microphones, audio consoles, etc.
The range of volume is [0, 100], the default value is 50, when the value of "Volume" is "0", it means mute, and when the value is "100", it is played at the maximum
volume input.
Select "Volume" in the audio setting interface, press the knob to enable volume setting, rotate the knob to adjust the output volume, and press the knob to confirm.
ÿ HDMI can carry audio input automatically, and the audio of HDMI input source can be modified to the audio of audio output interface.
ÿ The SDI interface does not support audio input, but the audio of the SDI input source can be set to the audio of the audio input interface.
Step 1 On the audio interface, turn the knob to select "Input Source Audio Settings".
Step 2 Press the knob to enter the "Input Source Audio Setting" interface.
www.novastar-led.cn 29
Machine Translated by Google
Step 3 Rotate the knob to select the input source, press the knob to enable the audio setting of the input source.
ÿ Audio In: Use the audio transmitted by the audio output interface (AUDIO) as the audio of the HDMI input source.
ÿ Audio In: Use the audio transmitted by the audio output interface (AUDIO) as the audio of the HDMI input source.
ÿNone : The SDI interface does not support audio transmission. When set to "None", the SDI input source has no audio input.
ÿ Audio In: Use the audio transmitted by the audio output interface (AUDIO) as the audio of the SDI input source.
Rotate the knob to select the audio of the input source, press the knob to confirm.
Advanced Features
Device self-test
The equipment self-test is used to detect whether the components of the equipment are running normally, so as to troubleshoot.
When there is a problem with the device, it can be automatically detected through the device self-test program, and the user can send the test result to the device maintenance personnel
During daily equipment testing, equipment health checks can be performed through the equipment self-inspection program.
On the main menu interface, select "Advanced Settings > Advanced Functions > Device Self-inspection", press the knob to enter the device self-inspection interface, check the self-
inspection prompt information, turn the knob to select "Yes", and press the knob to check the device.
www.novastar-led.cn 30
Machine Translated by Google
When the device is performing a self-test while the device is running, the output screen may display abnormally for a short time, and the screen will display after the self-test.
3D settings
V2460 works with 3D transmitter EMT200 and 3D glasses to make the screen display 3D effect. Please refer to A 3D function description for specific usage methods .
Step 3 Select "Advanced Settings > Advanced Functions > 3D", press the knob, and select "Enable".
www.novastar-led.cn 31
Machine Translated by Google
Step 4 Set the video source format, which can be set to "left and right", "top and bottom", "front and back frames".
Step 5 Set the priority of left and right eyes, select with 3D glasses, can be set to "left eye" or "right eye".
Step 6 Enter more settings, you can set the following information.
For more details on the operation of 3D functions, please refer to Appendix 3D Function Description.
point-to-point playback, if the 3D source is a left-right structure, you need to set the window width to the input source resolution.
Half of the resolution width; if the 3D source is a top-bottom structure, set the window height to half the resolution height of the input source.
ÿ Support saving 3D parameters to the scene, please refer to 5.7 Scene Settings for the specific saving method.
www.novastar-led.cn 32
Machine Translated by Google
Set the frame rate of the output image, the default value is 60Hz.
On the main menu interface, select "Advanced Settings > Output Frame Rate", press the knob to enable the output frame rate setting, turn the knob to select the output frame
Supported frame frequencies are: 24Hz, 25Hz, 30Hz, 48Hz, 50Hz, 56Hz, 60Hz, 70Hz, 72 Hz, 75 Hz, 85
After entering a certain menu, when no operation is performed on the current interface, the length of time to stay in the current interface, the default is 60s, and the maximum
is 3600s.
On the main menu interface, select "Advanced Settings > Back to Main Interface Duration", press the knob to enable the duration setting, rotate the knob to adjust the duration,
reset
Restoring factory settings is to restore all the settings of the machine to the default values set at the factory.
After the device is upgraded or the parameters set in the device are not applicable, all configuration parameters can be restored to the default value when the device leaves the factory by
On the main menu interface, select "Advanced Settings > Restore Factory Settings", and press the knob to enter the "Restore Factory Settings" interface.
www.novastar-led.cn 33
Machine Translated by Google
ÿReserve user data: user data includes screen configuration files, BKG, OSD and scenes saved by the user.
ÿReset all: All the setting parameters in the device are restored to the default values.
communication settings
Set the network related information of the device so that it can communicate and connect with the host computer. When setting the network information of the device, it is necessary to ensure
that the device and the host computer are in the same network segment, and the IP address of the device and the IP address of the host computer cannot conflict.
Step 1 On the main menu interface, turn the knob to select "Communication Settings", and press the knob to enter the "Communication Settings" interface.
Step 2 Turn the knob to select "Network Settings", and press the knob to enter the "Network Settings" interface.
Step 3 Turn the knob to select "Network Mode" to set the network mode.
ÿManual setting: You need to manually enter the IP address, subnet mask and default gateway information of the device.
ÿAutomatic setting: The system automatically assigns IP address information. When the device and the host computer are connected to the same router or switch, "Network
Step 4 When the "Network Mode" is set to "Manual", turn the knob to select "IP Address", "Subnet Mask" and "Default Gateway", and manually set
Configure the IP address, subnet mask and gateway information of the device.
Step 5 Turn the knob to select "Apply", and press the knob to make the set network information take effect.
Rotate the knob to select "Restore Default" and press the knob to restore all the set network parameters to the default configuration.
about me
www.novastar-led.cn 34
Machine Translated by Google
about Us
In About Us, you can check the firmware version information of the device, the official website and email information of the device provider, and check the update of the device through the official website.
New information or other equipment information, through the official mailbox, you can feedback the problems encountered in the use of the equipment or propose the required technical support
Select "About Us" on the main menu interface, and press the knob to enter the "About Us" interface.
www.novastar-led.cn 35
Machine Translated by Google
Specifications
Machine Specifications
gross weight
8.9 kg
accessory box 1×power cable, 1×DP cable, 1×HDMI cable, 1×CAT5E network cable, 1×screw
www.novastar-led.cn 36
Machine Translated by Google
YCbCr4:4:4
YCbCr4:2:2
YCbCr4:2:0
YCbCr4:4:4
YCbCr4:2:2 3840×2160@60Hz
YCbCr4:2:0
YCbCr4:4:4
YCbCr4:2:2
YCbCr4:4:4
YCbCr4:2:2 3840×2160@60Hz
YCbCr4:4:4
YCbCr4:2:2
YCbCr4:4:4
YCbCr4:2:2
ÿSupport ST-424 (3G), ST-292 (HD) and ST-259 (SD) standard video input
www.novastar-led.cn 37
Machine Translated by Google
A 3D function description
Step 2 Connect the network cable. At this time, the EMT200 can be connected in series to a certain network cable. After the EMT200 is powered on, turn on the matching 3D (shutter type)
Glasses switch.
Step 3 Configure the screen. It should be noted here that the load of a single network port is halved, and the load of the total device is halved.
Step 4 Select the format of the video source, if the video source is a left-right format, select [left and right]; if the video source is a top-bottom format, select [upper
Down]; if the video source is in front and back frame format, select [Back and Back Frame].
Step 5 Adjust the priority of left and right eyes. The left and right frames of the video playback may be inconsistent with the switching between the left and right eyes of the glasses, so this parameter needs to be adjusted.
It is recommended to adjust according to the actual observation effect after turning on 3D. By default, the left eye is given priority.
ÿ [left and right] format 1920×1080@60hz 3D source, adjust the starting position of the right eye to 960, if it is
3840×1080@60hz [left and right] format 3D source, the starting position of the right eye is adjusted to 1920. That is, [left and right] format
When using a 3D source, it is recommended to adjust the right eye position to one-half of the resolution width of the source.
ÿ For the 3D source of [up and down] format 1920×1080@60hz, adjust the starting position of the right eye to 540, if it is
3840×1080@60hz [Up and Down] format 3D source, the starting position of the right eye is adjusted to 540. That is, when the 3D source is in [upper and lower] format, it is recommended to
Step 7 Adjust the signal delay time so that the switching between the left and right eyes of the 3D glasses is synchronized with the switching between the left and right eyes of the display. It is recommended to adjust according
Step 8 Turn on 3D, at this time, V2460 will close other windows, leaving only window 1.
Step 9 The position and size of window 1 can be adjusted arbitrarily. This window supports 3D effects. After wearing the standard 3D glasses, you can see
3D effect now.
A.2 Precautions
1. After 3D is turned on, the load of the single network port of the device is halved, and the load of the device is halved.
www.novastar-led.cn 38
Machine Translated by Google
www.novastar-led.cn 39
Machine Translated by Google